CXN Conversation styles vs legacy voicemail systems

Similar Questions

• BlackBerry Smartphones speed dial an automated voicemail system

  I am a new user of BB and have asked several people how abbreviated to my office voicemail system to retrieve messages.  Previously on standard mobile phones, I dial phone number, insert "ppp" for breaks, while the auto attendant would make the next step.  There are 3 sets of number to get all the way in.  Example: 800-555-5555ppp555ppp5555ppp5555 and I would be able to retrieve messages.

  I tried a few different options and have be unsuccessful.  My carrier is AT & T.  BB is a Bold 9700.  Does anyone have any suggestions?

  Yes.

  When you program the speed dial, you will need to enter the number as a contact number in the address book. So, as you create this contact in the phone number entry screen, you will see the W or P support to enter the WAIT or PAUSE that you need.

• 200 concurrent sessions to a voicemail system

  Hello

  It is a call center where about 200 concurrent calls from PSTN leave messages in a voice mail box.

  The agents listen to messages and recall. Or a software can be written to read the caller id and deliver the caller ID to the agents.

  Are there Cisco products that can achieve this?

  Any information is appreciated.

  Best regards.

  By using the connection of the unit with HA.

  Sent by Cisco Support technique iPad App

• Conversion of QuickTime is eating hard drive space?

  So I thought I'd go through some old video files on an external drive, so when I found and tried to open them by default - open with Quicktime Player because they were .mov files. But when opening them that forced me to convert first, which took some time, but it was very good. After viewing the file, I have it closed and he could be invited to record the conversion, but I said no every time.

  Dozens of video clips later, I received a warning that my hard drive is running out of space even though I was not downloading anything. Of course, I'm up to 1 GB, even if I don't know I got a lot more than this, perhaps 20, but at least 10gbs before starting. I don't know Quicktime is somehow to blame, and whenever I try to open a .mov file and it begins to convert, I actually see my free disk space down a bit like 1.35 GB GB 1.06 to 53KO to zero bytes. However, now it crashes towards the end by saying: he can't open the clip, even if the conversion is almost over, and then my disk space back to about 1.35 GB. However, on my most recent test it is simply suspended zero byte. I quit the program and am currently stuck at zero-byte and get the impossible to open again message clip.

  I was able to open the same .mov files in VLC without problem. I tried to use OmniDiskSweeper to find where these ghosts files could be but nothing extraordinary appears. I can't find all the physical files that QuickTime can be created on my hard drive, unless I'm looking in the wrong places...

  I'm currently under OSX Yosemite v10.10.5 and Quicktime v10.4.

  If someone could help me please understand this point, I would be very happy. Thanks for reading this.

  If someone could help me please understand this point, I would be very happy.

  To start, I remember not where temporary files of conversion are stored by the system or if this location varies for different operating systems from the user. Basically, the problem is self-inflicted. When you refuse to save the file after the conversion, the reference of the source file ends up stored in your list of 'Récent' without for as much free disk space used to store the converted data. Try to access the data already converted via the "open the recent item" option will restart just another conversion of the same file. On the other hand, you had actually stored the converted file, you may have deleted or moved to an external drive for future use. Fortunately, if your system works like mine, there may be another way to reclaim the space for temporary storage consumed by conversions without having to know where temporary data is stored. Simply try to empty your "Récent" list by pressing the option "delete". Then watch the space window of Finder reading for a short period, while to see if the OS is recover storage space that has been allocated to the converted data. It worked for me under El Capitan, when I reset my normal 'None' setting return to the default value of '10' and ran some tests to try to reproduce your problem.

  

• 15 g092na: "the selected disc is the gpt partition style" during installation

  I am writing my phone because I'm stuck in win7 install. I deleted the partition with the surprising victory 8.1 and when I thought I'll just it chop and install win7, it is said that he has other plans. What should I do to let me install win7?

  During the installation of new versions of windows it is important to understand that there are two main formats of hard drives and there are also two forms of priming.

  UEFI boot:

  Newer computers come with what we call a uefi boot interface. This allows additional features such as start secure as well as HP UEFI to support environment that allows you to test different hardware without having to start an operating system.

  UEFI operating systems use the disc Table of Partition GUID (GPT) format that allows multiple partitions, as well as larger capacity hard drive.

  BIOS boot:

  Older computers have the BIOS that contans the basic as well as setting the date of the on-board system and clock. Features such as virtualization or CPU overclocking (according to availability on selected hardware) are able to be enabled or disabled in the BIOS. Most of the features of the BIOS have now been reproduced in the latest UEFI boot.

  BIOS according to the operating systems use the Master Boot Record (MBR) disk format that allows the support of legacy operationg systems.

  What it means:

  To downgrade your device Windows 8.1 to windows 7, you can either

  1. Format the disk to MBR format.  (Be sure to back up your data before doing this)
  2. Start your installation of windows media 7 in UEFI mode (make sure that your UEFI boot mode is set to UEFI hybrid for maximum compatibility)

  DiskPart allows you to select the physical disk, rather than the partitions so when you convert between MBR and GPT (and), you lose the recovery partition. Condition have recovery HP/Windows Media you shouldn't encounter too much trouble for the recovery of your computer.
  
  Hope this helped and good luck with your re-setup

• Desktop H500s put in the disk hard windows 10 from another OPERATING SYSTEM PC - ERROR CODE 1962 - No.

  I tried to replace the current hard drive with the disc provided with windows 10 from another PC.

  I have is after having swapped the hard drive. The system cannot load Windows 10 and displays this message "ERROR CODE 1962 - No. OPERATING SYSTEM".

  The main reason I like to swap the drive is because it is a larger and faster disk and it come with Windows 10 Enterprise license. Instead of my current hard drive of Levono who only 8.1 Windows

  I understand that the pilot is maybe a problem. But, I should at least be able to see the Windows screen and I can fix it the driver, instead of the message "ERROR CODE 1962 - No. OPERATING SYSTEM"

  Note: I did I tried to put this disc in the CD player, I've found, it can read the disc. Therefore, should not be SATA non-compliance issue.

  Any suggestion?

  Hope to hear the suggestion

  Dear all

  I managed to fix in Boot "Disable UEFI and activate the legacy", my system is running. I just need to install the audio driver after the system is running

  Usefully it doesn't matter who will help to have the same problem

• Voicemail will not play through bluetooth car

  I have a Moto X (Sprint) and it won't play my voicemails via Bluetooth... Worse that this, because I'm connected to bluetooth in the car, I can not play through the phone that either will I am in the car, everything is running... Does not work on buick Enclave wife either.

  Even the phone works fine, even a text for voicemail system on Buick is working well!

  Help!

  You are also able to use it during a call? You use stock voicemail (component number) or some visual voicemail application? You have the features A2DP (ability to listen to music via bluetooth from your car)?

• How can I delete the message from the voicemail from the screen of a SPA302D

  I have two combined SPA302D recorded on a SPA232D basis.

  My voip provider (voipfone.co.uk) provides a voicemail service.

  If it does not respond to a call, it is recovered by the voicemail system.  A voicemail icon on the SPA302D with the number of messages in voice mail box.

  However, I can't find anything to clear the voice mail of the screen icon.  I listened to voicemails and them deleted voipfone system, but can see no way to clear the message of the voicemail on the screen of the handset SPA302D.  I Goggled the question and searched this forum but have not found anything.

  If anyone has experienced this problem or have any suggestions to delete the message?

  I have no problem to implement market and of the voice of the screen as long as proper NOTIFICATION SIP are sent on the PBX side.

  Thus, to intercept SIP messages between your provider and the SPA232D base station. Check thatIP NOTIFIER content S 'pending Messages: no' arrived from your provider. Ask your provider for help that if no such message has arrived - the question is not about SPA232D.

  If not - paste the content of this message and reply of the adapter here. Enable syslog and debug messages and also well catch them. They are a valuable source of information and will help you/us to analyze the issue.

  I assume you are using the latest firmware (1.3.3 (15) on SPA232D, 2.62 on SPA302D)

• Voicemail configuration base with CUCM and connections of the unit

  Hello again,

  I'm still very new to CUCM.  I am configuring a CUCMB 6.01 test deployment.  He has connections in the integrated unit.  I have 2 DNs assigned to users and Cisco IP phones.  I use MGCP (Cisco 3745 with 2FXO as gateway).  Now, I'm trying to extensions of voicemail installation for the users.  I read a lot of documentation on CUCM and unity, but I know that Unity Express is not what I need, and that you have not found information on the basics of implementing voicemail for users of CUCM.

  Users are DN 1001 and 1002 respectively.  They are part of a list of hunting (broadcast) so that the arrival of incoming calls, both phones will ring simultaneously.  Not sure if this has any bearing or not.  I would like to be able to put in place so that each DN rings on the IP phone say 6 times, then go to a Unity voicemail box configuration for that user.  I have already imported users 2 in the unit.  I ran the voice messaging port configuration wizard.  Everything looks as if it runs correctly, but I'm stuck really share say CUCM to route the call to the mailbox of the unit.  Probably the simplest part.  Ideas or help on this would be much appreciated.  Thank you in advance.

  Impetuous salvation,

  CUCM works this way

  So the fact that 1001 and 1002 receive calls via a group has a significant impact on this config.

  You must keep in mind that a call that is routed through the fighter pilot will always ignore the CFWD settings on phones of hunting member of the group. The normal way to control it then is through disconnection of the Group Hunt members phones combined with the front fighter pilot level settings.

  The following section describes how the parameters to call it forward on the phones of individual members Hunt are ignored when presented a call via the hunting feature. Here's a clip;

  Hunting and call forwarding

  The concept of hunting differs from call forwarding. Hunting allows Cisco Unified Communications Manager to extend a call to one or more lists of numbers, where each such list can specify an order of hunting which is selected from a fixed set of algorithms. When a call extends over a part of hunting of these lists and the party does not answer or is busy, hunting resumes from the next part of hunting. (The next party of hunting varies according to the current hunting algorithm). Hunting has so ignore settings call forward No Answer (CFNA), call forward busy (CFB) or call before all (CFA) for the party to attempt (group member line phones).

  Cisco Unified Communications Manager offers the possibility to redirect a call when hunting fails (that is, when the hunt ends without a part of hunting to the respondent, due either to exhaust the list of numbers of hunting is to expire). If used, this final redirection includes an automatic call forwarding action. Therefore, the fighter pilot Configuration window includes call forwarding configuration concepts which are similar to those found on the directory number Configuration window.

  Example of a call hunt

  Although hunting is different from the transfer, Hunt often develops as a call that gets forwarded to a certain number of fighter-pilot. The protective cover of appeal extends from hunting to allow the final drive after two exhausts of hunting or expires.

  A typical call calling hunting can include the following phases:

  The appeal of hunting through groupings of posts set up according to the algorithms implemented for each group. Hunting is successful (if it meets a hunting party), exhausts (if all parts of hunting are tempted, but no response), or expires (if the deadline set by the Maximum hunting timer runs out before that all parties are tempted, and none of the parties who have tried to answer).

  For the purpose of this example, we assume that hunting does not succeed.

  If a form any of the final drive is configured, the call forward for a next destination; otherwise, the call is released.

  Maximum hunting timer

  The Maximum Hunt Timer field on fighter pilot Configuration window allows the administrator to enter a value (in seconds) to limit the hunting through a list of hunting season. After gaps in the time specified, if hunting was not successful, the call is transferred to a voicemail system, a specific compound number, or some personal treatment (if configured) or the call is released.

  The good doc.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/CUCM/Admin/6_0_1/ccmsys/a03rp.html#wp1078922

  If the call goes unanswered or all Member phones are disconnected, then an attacker needs to be applied at the level of the "fighter pilot".

  Hunt the settings forward

  Before hunting without an answer - when did not answered the call which is distributed through the list of hunting at a specific time, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Before busy hunt - when the call which is distributed through the list of hunting is busy at a precise moment, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Maximum Timer Hunt - enter a value (in seconds) that specifies the maximum duration for hunting. (Used in conjunction with Forward busy hunting)

  In your case, it is best to configure the DN of a fighter pilot in the extension of alternatives under the 1001 and 1002

  mailbox.

  I hope this helps!

  Rob

• Appeal of Smartphones blackBerry in a voicemail companies and the ability to spell

  When you call a company and you enter their voicemail system, it may ask you to spell the name people.  Is there a function on the curve which will display the alpha characters associated with a specific key, for example the 2 (or E) key is the a, b, c choice on a regular phone.

  You press the ALT key (lower left) and spell out the letters you need...

• BlackBerry Smartphones Can dial pad stay on screen then in a virtual machine system?

  Is there a way to make the telephone keypad remains visible during the audit of a voicemail system.  Whenever I call my voicemail to the company (or the Verizon also) key dial screen minimizes immediately and the screen with the options for speaker/Flash/Mute/add Participant rises.  And then every time I write a digital option to treat my VM (i.e. delete msg, respond, forward, etc...) I have to tap the screen twice to put the telephone keyboard on the screen, then enter the number of people.  I wouldn't mind the minimization 1 (I understand that it is a good screen for most of the calls from person to person), but once I got back the phone keyboard I want to stay there.  The extra keystrokes required are really annoying when you go there many VM on my company's system.

  Have you entered your phone settings and adjusted both your screen stays on? That could help as well.

  I have no problem to hit the dial button, and the keyboard remains for me.

• How to dynamically change the graphic style css?

  What is the right method to dynamically replace the graphic style of JavaFx 2.2 in the code? I modified the example in the tutorial below with or without loading the css file. So far, I am unable to replace the style from the code. My goal is to dynamically set the width of each line. We use Java with Eclipse on Windows 7 (64-bit) 7_51. The CSS generated in the code below works when it is in the file. There must be a better way than to write a new file and read it, right?

        String title = "Chart Title";
        stage.setTitle("Stage Title");
        final LogAxis xAxis = new NumberAxis();
        final NumberAxis yAxis = new NumberAxis();
        final LineChart<Number, Number> chart = new LineChart<>(xAxis, yAxis);
        chart.setTitle(title);
        chart.setLegendVisible(false);
        chart.setCreateSymbols(false);
        xAxis.setLabel("x-axis");
        yAxis.setLabel("y-axis");
  
        // each bar is a line from x,0 to x,y
        int width = 24; // pixels
        for (int i = 0; i < ydata.length; i++)
        {
           String css = "";
           // TODO: dynamically calculate unique width for each "bar"
           final XYChart.Series data = new XYChart.Series();
           data.setName("Series" + (i + 1));
           data.getData().add(new XYChart.Data(xdata[i], 0.0f));
           data.getData().add(new XYChart.Data(xdata[i], ydata[i]));
           chart.getData().add(data);
           // Dynamically set style instead of reading from file
           // Assign each "bar" data series a color and line width
           css += ".chart-series-line{ -fx-stroke: red; -fx-stroke-width: ";
           css += width;
           css += "px; }\n";
           data.getNode().setStyle(css);
           System.out.println("node style: " + data.getNode().getStyle());
           System.out.println("node style class: " + data.getNode().getStyleClass());
           width *= 3; // TODO: replace this with dynamic calculation of width
        } // end for
  
        final Scene scene = new Scene(chart, 800, 600);
        scene.getStylesheets().add("Chart.css");
        System.out.println("Scene stylesheet: " + scene.getStylesheets());
        System.out.println("chart style: " + chart.getStyle());
        System.out.println("chart style class: " + chart.getStyleClass());
        System.out.println("chart style sheet: " + chart.getStylesheets());
        stage.setScene(scene);
        stage.show();
  

  The Node #setStyle (String) method only supports the statements, not the rule full css. The setStyle call with '.chart-series-line {-fx-stroke...} '. "should give an error in the parser. Something like "whereas IDENT.

  You might find the line you want in the series. If series.getNode () is a form (as it will be for a line chart), you can just get the node in a form and call the setStrokeWidth() directly.

• How can I apply a shadow to the text of paragraph & there not as a system?

  Is there a way to text style, typekit, webfonts not system fonts?

  I wish I could have the styles, like the strokes, bevel etc on my text.

  Also, is the shadows to the text of the paragraph, not only title text, a widget for it?

  Thanks in advance.

  These features are not available for text in web browsers. They must be converted into images.

• Create new style box to highlight in Captivate 7 video demo to use several files of cpvc

  Hello

  Is it possible to create and then save a new style to display that can be used in several projects, when editing video demos in Catpivate 7? I can create a new style of economy, but when I open another file .cpvc is not available and I can't find a way to reuse/import.

  Any ideas? I don't know that I made a stupid mistake somewhere.

  You can export your new style in a local system folder and import it into your new project using the Style Manager object.

  Anthony

• Oracle cards: legend for dynamically generated styles

  Hi all
  
  I use the dynamically generated styles in my application of the Oracle cards. Depending on the situation, the style may be a variable marker or a color scheme. Now, I need to create a map legend, but I'm having a problem.
  
  A model of color scheme is defined and applied as:
  

  xmlDef = '<AdvancedStyle><ColorSchemeStyle basecolor="blue" strokecolor="black">' +
                          '<Buckets>' +
                              '<RangedBucket label="" high="' + value + '"/>' +
                              '<RangedBucket label="" low="' + value + '" high="' + value*2 + '"/>' +
                              '<RangedBucket label="" low="' + value*2 + '" high="' + value*3 + '"/>' +
                              '<RangedBucket label="" low="' + value*3 + '" high="' + value*4 + '"/>' +
                              '<RangedBucket label="" low="' + value*4 + '" high="' + value*5 + '"/>' +
                              '<RangedBucket label="" low="' + value*5 + '" high="' + value*6 + '"/>' +
                              '<RangedBucket label="" low="' + value*6 + '"/>' +
                          '</Buckets></ColorSchemeStyle></AdvancedStyle>';
                          
        style = new MVXMLStyle("COLOR", xmlDef);

  I can apply and see the results without any problem, however when I try to create a legend, like this:
  

  var html = "<table><tr><td><img src="+baseURL+"/omserver?sty=COLOR&w=180&h=175&ds=solap></td></tr></table>";
      
      legend = new MVMapDecoration(html,null,0.04,200,110);
      mapview.addMapDecoration(legend);

  I get an error of this style is not found 'COLOR ':
  

  May 25, 2009 7:35:17 AM oracle.sdovis.style.AllStyleTable getStyleObject
  WARNING: Cannot find style named COLOR of SYSTEM in all_sdo_styles
  May 25, 2009 7:35:17 AM oracle.lbs.mapserver.oms reportException
  SEVERE: Message:style not found

  It's strange because the style is there and successfully applied to the card, I just can't generate a legend. Any ideas please?
  
  Thanks in advance,
  ~ Ruben

  You can build an application of xml and use it in the url of the image. Make sure that you remove all redundant new lines and spaces in the query and call encodeURIComponent to encode it. Here is an example.

  var xmlreq = encodeURIComponent ("

  '");

  var html ="

  ";

  Caption = new MVMapDecoration(html,null,0.04,200,110);
  mapview.addMapDecoration (legend);