DAQmx, specify the resources occpaied

Similar Questions

• VISA (Hex 0xBFFF001E) error the specified state, the attribute is not valid or is not supported as defined by the resource.

  Hello

  First of all that I must say I just starting with control of the instrument using Labview. For this reason, it is possible that the problem I have is easy to solve. However, I am looking for any solution for the forum, but unfortunately I can't fint anything.

  While the situation is this: I'm looking to plug a power Analyzer (Yokogawa WT1800) with the PC through GPIB. To achieve this, I use the USB/GPIB Interface of Agilent 82357 B. The connection is done correctly because I can see and communicate with him through the Explorer NI MAX.

  In order to achieve control of the instrument using Labview, I downloaded and installed the driver of Yokogawa WT1800 (Driver instruments ykt1800) using the NI Instrument Driver Finder tool. The problem I have is that when I run the examples, I find the following error message:

  Error 1073807330 has occurred to the property (arg1) node in Yokogawa WT1800 Series.lvlib: Initialize.vi-> Yokogawa WT1800 series continuous measurement Normal.vi

  Possible reasons:

  VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not taken in charge as defined by the resource.

  I tried to change the input of the open Visa arguments vi because I think that this is where is the problem, but I can't reach any solution. The following image is attached to the block diagram of the initialize.vi:

  

  Any help is appreciated.

  Thank you.

  I suspect the redirect property. Try to remove it.

• VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not supported as defined by the resource.

  I try to open a com port Seraglio in LabVIEW get this error:

  VISA: (Hex 0xBFFF001E) the State specified, the attribute is not valid or is not supported as defined by the resource.

  It occurs in ISA set up a Serial Port (Instr) .vi and seems to be related to the speed of transmission. If I use anything else than 9600, I get this warning. I need to use 115200. I can open successfully to other com ports at 115200.

  I am able to talk to this device using other Terminal programs to 115200 without problem. It is only through LabVIEW and NI MAX.

  The Unit presents itself as "Stellaris Virtual Serial Port (COM12)" in deveice Manager.

  Is there a way to get around this?

  Thanks in advance!

  
  

• Startup error: DLL Load error can not load the resource dll: REPLRES. RLL the specified module could not be found

  Original title:

  ReplSync.dll - error loading DLL cannot load resource dll: REPLRES. RLL the specified module could not be found

  I get this error message whenever I start my computer: replsync.dll - DLL Load error can not load the resource dll: REPLRES. RLL specified module is not found Help please?  Thank you!

  Hello
  You did changes to the computer before the show?
  Method 1:
  Step 1:
  
  You can try to start in safe mode and check if the problem persists.

  The Advanced Boot Options screen lets you start Windows in advanced troubleshooting mode. You can access the menu by turning on your computer and pressing the F8 key before Windows starts.

  Some options, including the mode safe mode, start Windows in a limited State, where only the essential is started. If a problem doesn't reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as a possible cause.

  Advanced startup options
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
  
  Step 2:

  If the problem does not occur in safe mode, and then try to perform the clean boot and see if the problem still occurs. Clean boot helps eliminate software conflicts. For more information, see the following link:

  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the article mentioned above.

  Method 2:
  
  You can run Windows Defender Offline tool.

  See the following link for more information about the same:

  What is Windows Defender in offline mode?

  http://Windows.Microsoft.com/en-us/Windows/what-is-Windows-Defender-offline
  
  Windows Defender Offline: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows/Windows-Defender-offline-FAQ
  
  Note: data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  Method 3:
  
  Try the SFC (System File Checker) scan on the computer.

  SFC/scannow is a very useful command that you can use in any version of Windows. When the SFC (System File Checker) command is used with the/scannow switch, the tool analyzes all the important files of Windows on your computer and replace if necessary.

  Missing and the corruption of the operating system (like many DLLs) files are probably the main cause of the major problems of Windows. In view of this, plus the fact that the SFC/scannow is completely automatic and very easy to use, the tool should be usually one of your top not troubleshooting.

  Reference:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Let us know if it helps!

• How to specify the sampling frequency? Must use "measurement & Automation Explorer '?

  I use to measure the input current analog OR cDAQ-9171 (chassis only location USB) and NOR-9207. I have 2010 NOR-installed DAQmx and LabVIEW.

  How can I specify the sampling frequency?

  If I use M & A Explorer to create the task, I can specify the flow rate (Hz) on the Configuration tab-> sync settings.

  For the acquisition of data NOR, it is mandatory to use M & A exploring?

  If I don't want to use M & A Explorer, how can I specify the rate (Hz)?

  Hello

  You can specify the sampling frequency with "DAQmx Timing.vi" located in the function palette DAQmx (read context-sensitive help on how to use wisely).

  You do not have to use M & A exploring (MAX) to create a task.

  A simple and quick way is to use DAQ Assistant (same configuration as in MAX) to configure your measurement.

  Another is to use blocks of DAQmx function to manually build your application code.

  In my experience Assistant DAQ is ideal for simple tasks (one measure), with regard to the more complex measures (synchronized the analog and digital inputs).

  I tend to use function blocks because they give you more freedom about code execution.

  Note: You can also build DAQmx code from a wizard configured DAQ task.

  Best regards

  Matej

• Error-1074118631 after driver update "the name of the resource is not attributed...". "PXI-6562

  I just updated my version 1.5.3 to 1.7.4 niHSDIO driver and now the device, a PXI-6562 is won't boot. I get the following error. The VI is suspended for 30 ~ 60 s attempt to initialize before the error occurs.

  Code: - 1074118631

  Message: niHSDIO Init generation Session.vithe name of the resource is not assigned to an instrument supported by NOR-HSDIO.

  The device worked fine with the old driver.

  Windows Device Manager indicates that everything is installed and working.

  I tried to write a simple VI by using new versions of the screw HSDIO and recreating the I/O resource menu drop-down.

  The resources dropdown lists the name as "PXI1Slot2".

  I can see the device in MAX thanks its location listed as "chassis: 1; Slot: 2 "

  The PXI-6562 has 2 LEDs on the front panel for 'access', 'active'. No lights during an attempt to initialize.

  I tried uninstalling the driver in Windows, reinstalling and restarting: same problem.

  I tried to use the device in Signal Express, and it produces the same error.

  I use LabVIEW version 8.5 and Signal Express 2.5.

  

  

  

  

  Does anyone know how to fix this?

  Thank you

  Arthur

  Hey Arthur,.

  You should also do a repair on the NOR-DAQmx driver for example, after you have repaired HSDIO. Let us know how it goes. Thank you.

  Kind regards

  DJ L.

• Instrument not listed is not in the resource of VISA

  I have a GPIB resource.  He appears in MAX, but not on behalf of the constant resource.  I checked I/O filtering and updated the name of the resource, but the problem persists.  What is going on?  See attached picture.

  I tried some of these approaches, but they are not what I'm looking for.  It seems that even if the resource does not appear on labview, and I'm still able to talk to her if I manually enter the name of the resource.  The GPIB-USB instruments are those that gave me problems, because I would like to know the address specify the instruments but not their interface IDS. They use different controllers.

  I've written a vi this loop by interface 0-4 with a primary issue specified address id the * IDN? command and check the answer.  With this method, I am able to find the address of the GPIB string and speaks with the same visa instruments does not have this resource.

  I hope that this method will be held up through time.

• How to detect the resource (find) information?

  Hi all

  I'm trying to detect programmatically information resource name for devices HSDIO PXI and PXI-4130.   How can I do?    System DAQmx property does not include these devices, and I can't find a way to convert a resource VISA name in name of resource HSDIO or NI DC PS formats.  I enclose a code snippet that detects resource VISA for a device 6552 name, but I can't seem to figure out how to get the name of MAX the device resource.   Both the niHsdio and the properties of 'name of the resource' OR DcPS requires that you spend a session valid in them need valid resource name andI to make...

  And no, asking the operator to launch of MAX and find the name of the resource is not an option

  Thank you

  Hello

  Modular instruments and devices devices use their own set of screws to find devices in the system. The lybrary called NOR-ModInst and i's includedin the palette of the utility with the MID drivers.

  Here is a small example that demonstrates the use of their base.

  Let me know there are questions of the amy

  Kind regards

  JC

• Find the name of the resource of the SMU-4143 NI

  Hello world

  Is there a way to find the resource name assigned by MAX using LabVIEW? I need to use niDCpower initialize wite channels VI to initialize a session with SMU-4143. This VI asks the name of resource assigned by measurement & Automation Explorer (MAX) of the 'PXI1Slot3' form as input. I'm not sure whether we can use VISA find resources to detect the PXI instrument. If so, the resource to find string exit VISA is a different format. How can I get the name of resource affected by MAX of this? Any ideas?

  You can use a constant DAQmx device name or a control.

  Or you can do deactivation:

  

• I am not able to open a web address, Windows Live, because the resource does not respond.

  I'm not able to open my Windows Live Calendar that is created by Windows;

  https://CID-cc49fdd95b0ee0dd.Calendar.live.com/calendar/private/c839cef8-8d4f-47E2-9c85-77c9f425c449/9f1db3ad-6994-4981-8d1d-8f0d174e6a0a/index.html

  I get a message that the resource does not respond.

  Your suggestions help to access detailed information, as well as my email.

  Nonsense. If you see the details of your calendar when you click on the link I gave, then you are connected with the Live ID that is associated with the agenda. No matter who else by clicking above will see either his own calendar so it is connected, or an invitation to sign it if it is not.

  If you try to share a calendar with other people, then use the options to share on the calendar page. You can specify how much or little detail people see, including the only periods of availability.

  Please ask questions about Windows Live Calendar in the forum dedicated to it.

  Noel

• How to pass the resource Viewer setting task workflow in service - accordingly

  Hello

  I created a custom and created service rworkflow esource Viewer to allow custom resources to display.

  Here's the entry in service - accordingly

  	"< taskFlowId="/WEB-INF/custom-resource-viewer#custom-resource-viewer display ">
  	< Parameters >
  	< parameter name = value 'viewId' = 'news-detail-view' / >
  	< / Parameter >
  	< / display >

  but I'm not able to get viewId in my workflow:

  < af:outputText value = id "Rendering #{pageFlowScope.resourceId}" = "ot1" / > <! - it appears - >

  < af:outputText value = id "Rendering #{pageFlowScope.viewId}" = "ot13" / > <! -It's null->

  Please let me know if I'm missing something.

  Thank you

  -Yves

  Hi TheNewBee.

  Here I explain why increased only from these resources.

  • If you use <> using a workflow then commented the default parameters are sent in the workflow.
  • If you use <> with a call for implementation of ResourceUrlRewriter you can send more settings (custom) If you want added to default ones.

  My recommendation is that you have to take a look at in the IdentityResourceUrlRewriter and MessageFormatResourceUrlRewriter which are provided by WebCenter OOTB. It will give you an idea on how to implement a ResourceUrlRewriter.

  Taken from official (official documentation):

  Indicating a workflow ID

  This is used by the search, Tags and Discussions. Instead of having an ID of the view (page JSPX), the service provides a workflow to return the resource.

  • The attribute taskFlowId indicates that the converter is a workflow.
  • A workflow will be used to make the resource specified by the resource identifier.
  • The workflow will honor a resourceId input parameter and use it to restore the resource.

  By specifying a class name URL Rewriter

  or

  or

  This is used by services such as ITS Oracle and Documents, that specify a URL recorder in order to treat the resource in the form of URLS and rewriting ID that appropriately. URL burner modifies the resource ID in a URL that can be launched with a goLink. Two ResourceUrlRewriters are provided:

  • oracle.webcenter.framework.internal.resource.IdentityResourceUrlRewriterexists for ITS Oracle. It takes the resourceId value in the form of URL as is.
  • oracle.webcenter.framework.internal.resource.MessageFormatResourceUrlRewritersuitable for Documents. It takes a message parameter (in the service-definition ). The message parameter contains a {0} which will be replaced by the value of the resourceId . The urlExternal setting is applied to all the engravers of URL to tell the JSPX who consumes a resource action Manager link if it must open a new window.

  The default behavior is to launch a new dialogue window with that URL.

  No resource Viewer (as the ID layout resource ID)

  Some services, such as the service Page, may have no spectator resource but can allow dubbing their IDS of resources such as mode page IDs.

  I hope this helps.

  Kind regards.

• Control of the resources of the Machine

  Is there a way I can put the resources of the machine when im plans based NetApp FlexClone - creation models

  Or will the amount of RAM that is always picked up from the model? and that's why I need a model for my normal instance (2xCPU and 3 GB of RAM) and another model for an instance Lite (1xCPU and 1 GB of RAM)

  I tried specifying a custom property: VirtualMachine.Memory.Size but it made no difference. I can't change what the action plan as it changes back again once so presumably the model replaces the value of nay?

  I have not Advanced Services

  Thank you

  Jon

  cegjd - vRA/vCAC affects the size of the vCenter model at that point you the action plan the minimum CPU/memory. You cannot set the lower values that the model is configured for. If you want it lower, you will need to reduce model resources.

  A separate note on this subject, be sure to set the number of CPUS to 1 if you allow users to select processors how they want. If set you it to 2 and try to build a virtual machine with vRA and you select an odd number of CPUS the build fails. We have discovered this the hard way and we puzzled for a day.

• Error in moving VMS to the resource group

  Hello

  I'm trying to rebuild some ESXi hosts due to a hardware refresh. New ESXi hosts are in a cluster and eventually the old cluster will disappear because the virtual machines are migrated. I've implemented the script that works fine except for 1 error below. It seems that since we have groups of resources with the same names in all are clusters, it cannot determine where to place the virtual computer. Is there a way to specify the ID of the resource pool with the Move-VM command or another command? Or maybe a way to point to the list of resources in a cluster through a sort of way? I can easily rename Resource temporarily pools, but I want to continue to use the part of the script later to other familiar things.

  The exact error is that the specified parameter 'destination' expects only one value but your 'Low priority' name criteria corresponds to multiple values.

  Thanks in advance for any help!

  

  Hello

  Try something like this,

  $RP = get-ResourcePool | Where {$_.} {ID-like "* 27663"}

  Move-VM - VM VMName - Destination the $RP

  Kind regards

  Julien.

• Oracle/binding_permission_authorization_policy name of the resource

  Hello
  
  I was setting this policy and everything works fine if I specify
  
  
  Permission class: oracle.wsm.security.WSFunctionPermission
  The resource name:
  Action of permission: *.
  
  It is configured in the application with the application role related policies. Only users in the role are permitted to access the resource. I would like to link it to a specific resource now.
  
  
  I tried to change
  
  Resource name of: < < space of names > > / < < ServiceName > > # < < operation > >
  Action of permission: *.
  
  And
  
  The resource name for: *.
  Action of permission: call
  
  And
  
  Resource name of: < < space of names > > / < < ServiceName > > # < < operation > >
  Action of permission: call
  
  None of which work. I know that I have the correct namespace for the WSDL file and the name of the composite service and operation. They all give me permission errors. Any ideas?

  OK, an update, got the job by having the

  Name of the resource as > />

  Action as >

• vihostupdate - how do I specify the Bundle path

  Hello

  Have a new configuration of ESXi 4.0 U1 with vMA cluster. Downloaded the bundle of U2 to store data on the local host, but I can't find a way to specify the path to the bundle with the vihostupdate command. I can list the warehouses of data (and local host) with sharp - listds whereby, I see all attached data storage, but I don't know how to specify the path of all.

  I understand that ESXi is not "aware of file structure", but there must be a way to do this with the remote hosts.

  Anyone can shed some light on this?

  Thank you for your time.

  / r,.

  Smokey

  When you use vihostudpate on the vMA, the beam must be local to vMA and not the host ESX (i). All will then be transferred to your host and patched

  Here is an example on how to use the vihostupdate utility - http://vm-help.com/esx/esx3i/esx_3i_rcli/vihostupdate.php

  You can also find more information in the vCLI guide - http://www.vmware.com/support/developer/vcli/

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".