Dead Peer detection on VPN client
Hello world
I know that we can DPD over Anyconnect SSL config on cisco ASA.
You need to know we can configure the DPD on VPN on your PC as client?
Concerning
MAhesh
Mahesh,
DPD for ASA-side and Client-side detection are configured in the group policy on the ASA.
Here is a link to the section of the configuration guide and below a photo of the place where it is ASDM:
Tags: Cisco Security
Similar Questions
-
IKE Dead Peer Detection between Cisco ASA and Cisco PIX
I have a network environment in Star with about 30 offices of satellite remote using VPN Site to Site connectivity. The majority of remote satellite offices have the features of Cisco PIX 501 running PIX Version 6.3. The hub office runs a version 8.2 (1) Cisco ASA.
I configured Dead Peer Detection on the Cisco ASA device at the office hub with the default settings of the following-
Confidence interval - 10 seconds
Retry interval - 2 seconds
I think I'm right assuming that raises are limited to 3 before the tunnel is completely demolished. Basically, the problem that I am facing is with several remote satellite offices. What seems to be the case, the tunnel between the remote offices and the hub is demolished (probably because of the length of IKE, always 86400 seconds) and the tunnel then fails to renegotiate unless traffic is physically forced from the hub office. The tunnel NOT to renegotiate after satellite office, ONLY the end of the hub; so that means sending traffic to the satellite when the VPN tunnel is out of service, not to renegotiate the tunnel. The Hub office is a colo and therefore traffic rarely comes to that end, the tunnel remains so down until manual intervention occurs and the ICMP traffic is forced into the tunnel.
Should the KeepAlive and retry interval settings corresponds to both ends, for example if the two devices be configured for DPD?
What are the potential pitfalls to the extension of the life of IKE, and this will help or even hinder the problem?
Thank you in advance for helping out with this.
Hi Nicolas,.
I think that the two DPD settings must match on both ends, if these do not match then problems like yours might arise which seems to happen here, is that one end shows a tunnel down, but the other end may not detect it down, we could have to watch debugs, or record two ends to see if this is the case , setting in the meantime ike DPD for same timers could hetlp on.
In regard to the increase in the life expectancy of IKE, well you just need to be aware that this could allow keys to be discovered since these are not renegotiated unless the tunnel is down on the level of IKE. Other than that I don't see why this would affect you.
-
Dead Peer Detection and email?
Hello
Is it possible to get some kind of notification (such as email) when DPD detects a dead peer and failover to the next?
In this case, EasyVPN is used as a server and a client on two ASA 5505. 5505 has a failover server backup 5505.
Thanks i.a.
Hey Stan,
Check out this document, specifically "send System Log Messages to an e-mail address:
http://www.Cisco.com/en/us/docs/security/ASA/asa72/system/message/LogConf.html#wpmkr1107270
James
-
VPN client and peer simultaneously with dynamic ip
LAN (static ip) - to - Lan (static ip) is very well
LAN (static ip) - to - Lan(static ip) + VPN Client is fine
LAN (static ip) - to - Lan (dynamic ip) is very well
LAN (static ip) - to - Client VPN is good
LAN (static ip) - to - Lan(dynamic ip) + VPN Client does not work
I think that the problem is due to this commans
ISAKMP crypto keyname key address 0.0.0.0 0.0.0.0
or
ISAKMP crypto keyname key address 0.0.0.0 0.0.0.0 no.-xauth
How can I distinguish a router with a dynamic ip address that doesn't require authentication from a VPN Client that requires authentication?
P.D. I use local authentication
You are right in your diagnosys of the problem, we see this from time to time and there is not much that can be done unfortunately.
The only way is if the remote peer Gets a subnet or a dynamic address on a particular beach all the time, then add a line "isakmp key... No.-xauth" with this defined subnet. For example, if the remote peer always receives an address in 4.104.225.0/24, then do:
> cry isa key address 4.104.225.0 255.255.255.0 no.-xauth
Not much, but it's the only way around it.
-
VPN site to site & outdoor on ASA 5520 VPN client
Hi, I'm jonathan rivero.
I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.
the executed show.
ASA1 (config) # sh run
: Saved
:
ASA Version 8.0 (2)
!
hostname ASA1
activate 7esAUjZmKQSFDCZX encrypted password
names of
!
interface Ethernet0/0
nameif inside
security-level 100
address 172.16.3.2 IP 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 200.20.20.1 255.255.255.0
!
interface Ethernet0/1.1
VLAN 1
nameif outside1
security-level 0
no ip address
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/5
Shutdown
No nameif
no level of security
no ip address
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
object-group, net-LAN
object-network 172.16.0.0 255.255.255.0
object-network 172.16.1.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
object-group, NET / remote
object-network 172.16.100.0 255.255.255.0
object-network 172.16.101.0 255.255.255.0
object-network 172.16.102.0 255.255.255.0
object-network 172.16.103.0 255.255.255.0
object-group network net-poolvpn
object-network 192.168.11.0 255.255.255.0
access list outside nat extended permit ip net local group object all
access-list extended sheep allowed ip local object-group net object-group net / remote
access-list extended sheep allowed ip local object-group net net poolvpn object-group
access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group
pager lines 24
Within 1500 MTU
Outside 1500 MTU
outside1 MTU 1500
IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 100 burst-size 10
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 access list outside nat
Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1
Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
!
!
internal vpngroup1 group policy
attributes of the strategy of group vpngroup1
banner value +++ welcome to Cisco Systems 7.0. +++
value of 192.168.0.1 DNS server 192.168.1.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value splittun-vpngroup1
value by default-ad domain - domain.local
Split-dns value ad - domain.local
the address value ippool pools
username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15
tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared-key *.
type tunnel-group vpngroup1 remote access
tunnel-group vpngroup1 General-attributes
ippool address pool
Group Policy - by default-vpngroup1
vpngroup1 group of tunnel ipsec-attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:00000000000000000000000000000000
: end
ASA2 (config) #sh run
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
VPNL2L interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared key ciscomy topology:
I try with the following links, but did not work
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml
Best regards...
"" I thing both the force of the SAA with the new road outside, why is that? ".
without the road ASA pushes traffic inward, by default.
In any case, this must have been a learning experience.
Hopefully, this has been no help.
Please rate, all the helful post.
Thank you
Rizwan Muhammed.
-
Windows - Internet access, no split Tunnel L2TP VPN Clients does not
Greetings!
I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.
I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.
Here is the configuration:
: Saved
:
ASA Version 1.0000 11
!
SGC hostname
domain somewhere.com
names of
COMMENTS COMMENTS LAN 192.168.2.0 name description
name 75.185.129.13 description of SGC - external INTERNAL ASA
name 172.22.0.0 description of SITE1-LAN Ohio management network
description of SITE2-LAN name 172.23.0.0 Lake Club Network
name 172.24.0.0 description of training3-LAN network Southwood
description of training3 - ASA 123.234.8.124 ASA Southwoods name
INTERNAL name 192.168.10.0 network Local INTERNAL description
description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
description of Apollo name 192.168.10.4 INTERNAL domain controller
description of DHD name 192.168.10.2 Access Point #1
description of GDO name 192.168.10.3 Access Point #2
description of Odyssey name 192.168.10.5 INTERNAL Test Server
CMS internal description INTERNAL ASA name 192.168.10.1
name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
description of training3-VOICE name Southwood Voice Network 10.1.0.0
name 172.25.0.0 description of training3-WIFI wireless Southwood
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif INSIDE
security-level 100
255.255.255.0 SGC-internal IP address
!
interface Vlan3
nameif COMMENTS
security-level 50
IP 192.168.2.1 255.255.255.0
!
interface Ethernet0/0
Time Warner Cable description
!
interface Ethernet0/1
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/2
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/4
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/5
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/6
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/7
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
boot system Disk0: / asa821-11 - k8.bin
Disk0: / config.txt boot configuration
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
INTERNAL DNS domain-lookup
DNS domain-lookup GUEST
DNS server-group DefaultDNS
Name-Server 4.2.2.2
domain somewhere.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
the DM_INLINE_NETWORK_1 object-group network
network-object SITE1-LAN 255.255.0.0
network-object SITE2-LAN 255.255.0.0
network-object training3-LAN 255.255.0.0
object-group training3-GLOBAL network
Southwood description Global Network
network-object training3-LAN 255.255.0.0
network-object training3-VOICE 255.255.0.0
network-object training3-WIFI 255.255.0.0
DM_INLINE_TCP_2 tcp service object-group
EQ port 5900 object
EQ object Port 5901
object-group network INTERNAL GLOBAL
Description Global INTERNAL Network
network-object INTERNAL 255.255.255.0
network-object INTERNALLY-VPN 255.255.255.0
access-list outside_access note Pings allow
outside_access list extended access permit icmp any CMS-external host
access-list outside_access note that VNC for Camille
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
access-list outside_access note INTERNAL Services
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
no pager
Enable logging
exploitation forest asdm warnings
Debugging trace record
Outside 1500 MTU
MTU 1500 INTERNAL
MTU 1500 COMMENTS
192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
enable ASDM history
ARP timeout 14400
Global 1 interface (outside)
(INTERNAL) NAT 0 access-list sheep
NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
NAT (GUEST) 1 0.0.0.0 0.0.0.0
5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
Access-group outside_access in interface outside
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server Apollo
Apollo (INTERNAL) AAA-server Apollo
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 INTERNAL
http 0.0.0.0 0.0.0.0 COMMENTS
No snmp server location
No snmp Server contact
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
correspondence address 1 card crypto outside_map INTERNAL SITE1
card crypto outside_map 1 set of peer SITE1 - ASA
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
address for correspondence card crypto outside_map 2 INTERNAL training3
outside_map 2 peer training3 - ASA crypto card game
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
address for correspondence outside_map 3 card crypto INTERNAL SITE2
game card crypto outside_map 3 peers SITE2 - ASA
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
delimiter group @.
Telnet training3 - ASA 255.255.255.255 outside
Telnet SITE2 - ASA 255.255.255.255 outside
Telnet SITE1 - ASA 255.255.255.255 outside
Telnet 0.0.0.0 0.0.0.0 INTERNAL
Telnet 0.0.0.0 0.0.0.0 COMMENTS
Telnet timeout 60
SSH enable ibou
SSH training3 - ASA 255.255.255.255 outside
SSH SITE2 - ASA 255.255.255.255 outside
SSH SITE1 - ASA 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 INTERNAL
SSH 0.0.0.0 0.0.0.0 COMMENTS
SSH timeout 60
Console timeout 0
access to the INTERNAL administration
Hello to tunnel L2TP 100
interface ID client DHCP-client to the outside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd ping_timeout 750
dhcpd outside auto_config
!
address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
dhcpd Apollo Odyssey interface INTERNAL dns
dhcpd somewhere.com domain INTERNAL interface
interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
enable dhcpd INTERNAL
!
dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
enable dhcpd COMMENTS
!a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.43.244.18 prefer external source
WebVPN
allow outside
CSD image disk0:/securedesktop-asa-3.4.2048.pkg
SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
enable SVC
Group Policy DefaultRAGroup INTERNAL
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
Group Policy DefaultWEBVPNGroup INTERNAL
attributes of Group Policy DefaultWEBVPNGroup
VPN-tunnel-Protocol webvpn
Group Policy DefaultL2LGroup INTERNAL
attributes of Group Policy DefaultL2LGroup
Protocol-tunnel-VPN IPSec l2tp ipsec
Group Policy DefaultACVPNGroup INTERNAL
attributes of Group Policy DefaultACVPNGroup
VPN-tunnel-Protocol svc
attributes of Group Policy DfltGrpPolicy
value of 192.168.10.4 DNS Server 4.2.2.2
VPN - 25 simultaneous connections
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
the value INTERNAL VPN address pools
chip-removal-disconnect disable card
WebVPN
SVC keepalive no
client of dpd-interval SVC no
dpd-interval SVC bridge no
value of customization DfltCustomization
attributes global-tunnel-group DefaultRAGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Disable ISAKMP keepalive
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
attributes global-tunnel-group DefaultWEBVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultWEBVPNGroup
tunnel-group 123.234.8.60 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.60
pre-shared-key *.
tunnel-group 123.234.8.124 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.124
pre-shared-key *.
tunnel-group 123.234.8.189 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.189
pre-shared-key *.
type tunnel-group DefaultACVPNGroup remote access
attributes global-tunnel-group DefaultACVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultACVPNGroup
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
inspect the they
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
: end
ASDM image disk0: / asdm - 623.bin
ASDM location Camille 255.255.255.255 INTERNAL
ASDM location INTERNAL CGT-external 255.255.255.255
ASDM location INTERNAL SITE1-LAN 255.255.0.0
ASDM location INTERNAL SITE2-LAN 255.255.0.0
ASDM location INTERNAL training3-LAN 255.255.0.0
ASDM location INTERNAL training3 - ASA 255.255.255.255
ASDM location INTERNAL GDO 255.255.255.255
ASDM location INTERNAL SITE1 - ASA 255.255.255.255
ASDM location INTERNAL SITE2 - ASA 255.255.255.255
ASDM location INTERNAL training3-VOICE 255.255.0.0
ASDM location puppy 255.255.255.255 INTERNAL
enable ASDM historyI should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.
You must configure * intercept-dhcp enable * in your group strategy:
attributes of Group Policy DefaultRAGroup
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.comIntercept-dhcp enable
-Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked. It is located on the Advanced tab of VPN client TCP/IP properties. Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.
Alex
-
Cisco VPN Client 5.0.0 does not connect
Hello
I am trying to establish the VPN session the firewall to 5525 X Cisco ASA crossing 9.1.1 Cisco VPN Client. Although AnyConnect is the way to go, the inherited method must always be supported for some time as part of a migration. I tried two VPN users (authenticated by ad) on two client computers running Windows 7 64 bit and Cisco VPN Client 5.0.07.0440. Both users are able to establish a session to a computer at the ASA, but not the other. Entering credentails evil, the login popup will appear immediately. On the combination of username/password correct name, the following VPN client log messages are generated and the session drops that is "not connected" in the status bar. The PCF file is the same on both client computers.
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
119 22:49:16.933 06/23/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 203.99.111.44.
120 22:49:16.939 06/23/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
121 22:49:16.942 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 203.99.111.44
122 22:49:16.973 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
123 22:49:16.973 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 203.99.111.44
124 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
125 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
126 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
127 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
128 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
129 22:49:16.977 06/23/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
130 22:49:16.977 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 203.99.111.44
131 22:49:16.977 06/23/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
132 22:49:16.977 06/23/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xCA7C, Remote Port = 0x1194
133 22:49:16.977 06/23/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
134 22:49:17.000 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
135 22:49:17.000 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
136 22:49:17.211 06/23/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
137 22:49:17.211 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
138 22:49:23.207 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
139 22:49:23.393 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
140 22:49:23.393 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
141 22:49:23.393 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
142 22:49:23.401 06/23/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
143 22:49:23.401 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
144 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
145 22:49:23.427 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
146 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.2.193.69
147 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.2.5.2
148 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 10.1.5.2
149 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000000
150 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
151 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 10.0.0.0
mask = 255.0.0.0
protocol = 0
src port = 0
dest port=0
152 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = example.org
153 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
154 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5525 Version 9.1(1) built by builders on Wed 28-Nov-12 11:15 PST
155 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
156 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
157 22:49:23.445 06/23/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
158 22:49:23.445 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.99.111.44
159 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
160 22:49:23.477 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 203.99.111.44
161 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
162 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 7 seconds, setting expiry to 86393 seconds from now
163 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
164 22:49:23.477 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from 203.99.111.44
165 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to 203.99.111.44
166 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=F3E3C530
167 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
168 22:49:23.478 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
169 22:49:23.479 06/23/13 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65
170 22:49:23.479 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from 203.99.111.44
171 22:49:24.310 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
172 22:49:26.838 06/23/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
173 22:49:26.849 06/23/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
174 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
175 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
176 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
177 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
Any ideas why the second client of Windows 7 does not work?
Kind regards
Rick.
Rick
Thanks for the additional output. It shows the xauth authentication step, which is good to see. But it does not offer much clarity on what is causing the problem.
My attention is drawn to a couple of message on the balls that are in line with the two sessions for which you posted newspapers.
32 00:36:08.178 24/06/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
I'm not sure that we see any answer to this, but it makes me wonder if it is somehow involved in the issue. Is it possible that there is a difference in the configuration of firewall and operating between two clients?
I am also interested in this series of posts
48 00:36:08.210 24/06/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
I don't know why the pilot requested a key at this point, and I wonder why the remote IP is 0.0.0.0?
It is followed by a package in which the ASA provides the value of the life of SA - which seems to be on the path to a successful connection. that is followed by
55 00:36:08.350 24/06/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = 203.99.111.44
56 00:36:08.350 24/06/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">
during which the SAA indicates that no proposal has been selected. It seems therefore that the ASA is not happy about something.
If we do not find indications of the client that allows to identify the problem, then maybe we look at the ASA. Are all log messages generated on the SAA during this attempt to establish VPN that could show us the problem? Would it not be possible to run debugs on the SAA in a trial of this machine?
HTH
Rick
-
Another problem with the configuration of Cisco VPN Client access VPN Site2site
We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site. JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support. So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0
Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.
CORP netowrk 192.168.1.0
IP VPN 192.168.12.0 pool
Colo 10.1.0.0 internal ip address
Also, here's an example of my config ASA
: Saved
:
ASA Version 8.2 (1)
!
hostname lwchsasa
names of
name 10.1.0.1 colo
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
backup interface Vlan12
nameif outside_pri
security-level 0
IP 64.20.30.170 255.255.255.248
!
interface Vlan12
nameif backup
security-level 0
IP 173.165.159.241 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 12
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network NY
object-network 192.168.100.0 255.255.255.0
BSRO-3387 tcp service object-group
port-object eq 3387
BSRO-3388 tcp service object-group
port-object eq 3388
BSRO-3389 tcp service object-group
EQ port 3389 object
object-group service tcp OpenAtrium
port-object eq 8100
object-group service Proxy tcp
port-object eq 982
VOIP10K - 20K udp service object-group
10000 20000 object-port Beach
the clientvpn object-group network
object-network 192.168.12.0 255.255.255.0
APEX-SSL tcp service object-group
Description of Apex Dashboard Service
port-object eq 8586
object-group network CHS-Colo
object-network 10.1.0.0 255.255.255.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.1.0 255.255.255.0
host of the object-Network 64.20.30.170
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
ICMP service object
service-object icmp traceroute
the purpose of the service tcp - udp eq www
the tcp eq ftp service object
the purpose of the tcp eq ftp service - data
the eq sqlnet tcp service object
EQ-ssh tcp service object
the purpose of the service udp eq www
the eq tftp udp service object
object-group service DM_INLINE_SERVICE_2
the purpose of the ip service
ICMP service object
EQ-ssh tcp service object
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0
outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
outside_pri_access_in list extended access permit tcp any interface outside_pri eq www
outside_pri_access_in list extended access permit tcp any outside_pri eq https interface
outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100
outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface
outside_pri_access_in list extended access permit icmp any any echo response
outside_pri_access_in list extended access permit icmp any any source-quench
outside_pri_access_in list extended access allow all unreachable icmp
outside_pri_access_in list extended access permit icmp any one time exceed
outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586
levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0
outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0
outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0
outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0
Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list
OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0
L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
exploitation forest asdm warnings
record of the rate-limit unlimited level 4
destination of exports flow inside 192.168.1.1 2055
timeout-rate flow-export model 1
Within 1500 MTU
outside_pri MTU 1500
backup of MTU 1500
local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 100 burst-size 5
ICMP allow any inside
ICMP allow any outside_pri
don't allow no asdm history
ARP timeout 14400
NAT-control
interface of global (outside_pri) 1
Global 1 interface (backup)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside_pri) 0-list of access OUTSIDE-NAT0
backup_nat0_outbound (backup) NAT 0 access list
static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns
static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns
Access-group outside_pri_access_in in the outside_pri interface
Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1
Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254
Timeout xlate 03:00
Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
http server enable 981
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside_pri
http 0.0.0.0 0.0.0.0 backup
SNMP server group Authentication_Only v3 auth
SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection tcpmss 1200
monitor SLA 123
type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri
Annex ALS life monitor 123 to always start-time now
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outside_pri
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_pri_map 1 match address outside_pri_1_cryptomap
card crypto outside_pri_map 1 set pfs
peer set card crypto outside_pri_map 1 50.75.217.246
card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5
card crypto outside_pri_map 2 match address outside_pri_cryptomap
peer set card crypto outside_pri_map 2 216.59.44.220
card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
86400 seconds, duration of life card crypto outside_pri_map 2 set security-association
card crypto outside_pri_map 3 match address outside_pri_cryptomap_1
peer set card crypto outside_pri_map 3 216.59.44.220
outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
card crypto outside_pri_map interface outside_pri
crypto isakmp identity address
ISAKMP crypto enable outside_pri
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 50
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
!
track 1 rtr 123 accessibility
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd auto_config outside_pri
!
dhcpd address 192.168.1.51 - 192.168.1.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
rental contract interface 86400 dhcpd inside
dhcpd field LM inside interface
dhcpd allow inside
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection host number rate 2
no statistical threat detection tcp-interception
WebVPN
port 980
allow inside
Select outside_pri
enable SVC
attributes of Group Policy DfltGrpPolicy
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal GroupPolicy2 group strategy
attributes of Group Policy GroupPolicy2
Protocol-tunnel-VPN IPSec svc
internal levelwingVPN group policy
attributes of the strategy of group levelwingVPN
Protocol-tunnel-VPN IPSec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl
username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard
aard attribute username
VPN-group-policy levelwingVPN
type of remote access service
rcossentino 4UpCXRA6T2ysRRdE encrypted password username
username rcossentino attributes
VPN-group-policy levelwingVPN
type of remote access service
bcherok evwBWqKKwrlABAUp encrypted password username
username bcherok attributes
VPN-group-policy levelwingVPN
type of remote access service
rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username
rscott username attributes
VPN-group-policy levelwingVPN
sryan 47u/nJvfm6kprQDs password encrypted username
sryan username attributes
VPN-group-policy levelwingVPN
type of nas-prompt service
username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0
username cbruch attributes
VPN-group-policy levelwingVPN
type of remote access service
apellegrino yy2aM21dV/11h7fR password encrypted username
username apellegrino attributes
VPN-group-policy levelwingVPN
type of remote access service
username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5
username rtuttle attributes
VPN-group-policy levelwingVPN
username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin
username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0
username nbrothers attributes
VPN-group-policy levelwingVPN
clong z.yb0Oc09oP3/mXV encrypted password username
clong attributes username
VPN-group-policy levelwingVPN
type of remote access service
username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0
username attributes finance
VPN-group-policy levelwingVPN
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
type of remote access service
IPSec-attributes tunnel-group DefaultL2LGroup
Disable ISAKMP keepalive
tunnel-group 50.75.217.246 type ipsec-l2l
IPSec-attributes tunnel-group 50.75.217.246
pre-shared-key *.
Disable ISAKMP keepalive
type tunnel-group levelwingVPN remote access
tunnel-group levelwingVPN General-attributes
address LVCHSVPN pool
Group Policy - by default-levelwingVPN
levelwingVPN group of tunnel ipsec-attributes
pre-shared-key *.
tunnel-group 216.59.44.221 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.221
pre-shared-key *.
tunnel-group 216.59.44.220 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.220
pre-shared-key *.
Disable ISAKMP keepalive
!
!
!
Policy-map global_policy
!
context of prompt hostname
Cryptochecksum:ed7f4451c98151b759d24a7d4387935b
: end
Hello
It seems to me that you've covered most of the things.
You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel
outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo
Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.
-Jouni
-
Hi guru of cisco
Help me please to configure VPN access on ASA 5505 for Cisco VPN Client. I want to let the customers gateway, but access remote 192.168.17.0/24 and 192.168.10.0/24 (connected through site-to-site) networks.
Will be much appreciated for your help.
My config:
Output from the command: 'display conf '.
!
ASA Version 8.2 (2)
!
name of host host1
domain domain name
activate the encrypted password password
encrypted passwd password
names of
!
interface Vlan1
Description INTERNET
0000.0000.0001 Mac address
nameif WAN
security-level 0
IP address a.a.a.a 255.255.255.248 watch a1.a1.a1.a1
OSPF cost 10
!
interface Vlan2
OLD-PRIVATE description
0000.0000.0102 Mac address
nameif OLD-private
security-level 100
IP 192.168.17.2 255.255.255.0 watch 192.168.17.3
OSPF cost 10
!
interface Vlan6
Description MANAGEMENT
0000.0000.0106 Mac address
nameif management
security-level 100
IP 192.168.1.2 255.255.255.0 ensures 192.168.1.3
OSPF cost 10
!
interface Vlan100
Failover LAN Interface Description
!
interface Ethernet0/0
!
interface Ethernet0/1
Shutdown
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport trunk allowed vlan 2.6
switchport mode trunk
!
interface Ethernet0/7
Shutdown
!
boot system Disk0: / asa822 - k8.bin
passive FTP mode
DNS domain-lookup WAN
DNS server-group DefaultDNS
Server name dns.dns.dns.dns
domain domain name
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service RDP - tcp
RDP description
EQ port 3389 object
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-protocol udp
object-tcp protocol
Access extensive list ip 192.168.17.0 LAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
Standard access list LAN_IP allow 192.168.17.0 255.255.255.0
WAN_access_in list of allowed ip extended access all any debug log
WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 192.168.10.0 255.255.255.0 inactive debug log
WAN_access_in list extended access permit tcp any object-group RDP any RDP log debugging object-group
WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 a.a.a.a 255.255.255.248 debug log
MANAGEMENT_access_in list of allowed ip extended access all any debug log
access-list extended OLD-PRIVATE_access_in any allowed ip no matter what debug log
access-list OLD-PRIVATE_access_in allowed extended object-group DM_INLINE_PROTOCOL_1 interface OLD-private 192.168.10.0 255.255.255.0 inactive debug log
access-list OLD-PRIVATE_access_in allowed extended object-group TCPUDP interface OLD-private no matter what inactive debug log
access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.10.254 interface private OLD newspaper inactive debugging
access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.17.155 interface private OLD newspaper debugging
access-list 101 extended allow host tcp 192.168.10.7 any eq 3389 debug log
Access extensive list ip 192.168.17.0 WAN_1_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
Capin list extended access permit ip host 192.18.17.155 192.168.10.7
Capin list extended access permit ip host 192.168.10.7 192.168.17.155
LAN_access_in list of allowed ip extended access all any debug log
Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_nat0_outbound list of allowed ip extended access all 192.168.17.240 255.255.255.252
WAN_nat0_outbound to access extended list ip 192.168.2.0 allow 255.255.255.0 192.168.2.0 255.255.255.248
Access extensive list ip 192.168.17.0 WAN_2_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.17.0 255.255.255.0
LAN_IP_inbound list standard access allowed 192.168.10.0 255.255.255.0
Standard access list IPSec_VPN_splitTunnelAcl allow a
access extensive list ip 192.168.17.0 vpnusers_splitTunnelAcl allow 255.255.255.0 any
sheep - in extended Access-list allow IP 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
pager lines 24
Enable logging
logging trap information
asdm of logging of information
Debugging trace record
MTU 1500 WAN
MTU 1500 OLD-private
MTU 1500 management
mask 192.168.1.150 - 192.168.1.199 255.255.255.0 IP local pool VPN_Admin_IP
IP local pool vpnclient 192.168.2.1 - 192.168.2.5 mask 255.255.255.0
failover
primary failover lan unit
failover lan interface failover Vlan100
15 75 holdtime interface failover pollTime
key changeover *.
failover interface ip failover 192.168.100.1 255.255.255.0 ensures 192.168.100.2
ICMP unreachable rate-limit 1 burst-size 1
ICMP permitted host b.b.b.b WAN
ICMP allow 192.168.10.0 255.255.255.0 WAN
ICMP permitted host c.c.c.c WAN
ICMP allow 192.168.17.0 255.255.255.0 WAN
ICMP deny any WAN
ICMP permitted host OLD-private b.b.b.b
ICMP allow 192.168.10.0 255.255.255.0 OLD-private
ICMP allow 192.168.17.0 255.255.255.0 OLD-private
ICMP permitted host c.c.c.c OLD-private
ICMP permitted host b.b.b.b management
ICMP permitted host 192.168.10.0 management
ICMP permitted host 192.168.17.138 management
ICMP permit 192.168.1.0 255.255.255.0 management
ICMP permitted host 192.168.1.26 management
ASDM image disk0: / asdm - 631.bin
don't allow no asdm history
ARP timeout 14400
Global (WAN) 1 interface
Global (OLD-private) 1 interface
Global interface (management) 1
NAT (OLD-private) 0-list of access WAN_nat0_outbound
NAT (OLD-private) 1 0.0.0.0 0.0.0.0
WAN_access_in access to the WAN interface group
Access-group interface private-OLD OLD-PRIVATE_access_in
Access-group MANAGEMENT_access_in in the management interface
Route WAN 0.0.0.0 0.0.0.0 a.a.a.185 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
local AAA authentication attempts 10 max in case of failure
Enable http server
http 192.168.1.0 255.255.255.0 WAN
http 0.0.0.0 0.0.0.0 WAN
http a.a.a.a 255.255.255.255 WAN
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Service resetoutside
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto WAN_map 1 corresponds to the address WAN_1_cryptomap
card crypto WAN_map 1 set peer b.b.b.b
WAN_map 1 transform-set ESP-DES-SHA crypto card game
card crypto WAN_map WAN interface
ISAKMP crypto enable WAN
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
the Encryption
sha hash
Group 1
life 86400
Telnet timeout 5
SSH b.b.b.b 255.255.255.255 WAN
SSH timeout 30
SSH version 2
Console timeout 0
dhcpd auto_config OLD-private
!a basic threat threat detection
host of statistical threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 129.6.15.28 source WAN prefer
WebVPN
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec svc webvpn
internal admin group strategy
group admin policy attributes
DNS.DNS.DNS.DNS value of DNS server
Protocol-tunnel-VPN IPSec
internal vpn_ipsec group policy
attributes of the strategy of group vpn_ipsec
value 192.168.17.80 DNS server dns.dns.dns.dns
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_ipsec_splitTunnelAcl
the address value vpnclient pools
username admin password encrypted password privilege 15
n1ck encrypted password privilege 15 password username
type tunnel-group admin remote access
tunnel-group admin general attributes
address pool IPSec_VPN_pool
vpnclient address pool
LOCAL authority-server-group
strategy-group-by default admin
tunnel-group admin ipsec-attributes
pre-shared-key *.
tunnel-group b.b.b.b type ipsec-l2l
tunnel-group b.b.b.b General-attributes
strategy-group-by default admin
b.b.b.b tunnel ipsec-attributes group
pre-shared-key *.
NOCHECK Peer-id-validate
type tunnel-group vpn_ipsec remote access
tunnel-group vpn_ipsec General-attributes
vpnclient address pool
Group Policy - by default-vpn_ipsec
vpn_ipsec group of tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmpThanks a lot for the confirmation. There is some lack of configurations and also some configuration errors.
They are here:
(1) Split tunnel-access list is incorrect:
vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
It should be allowed in your internal network. Please, add and remove the following:
standard access list vpn_ipsec_splitTunnelAcl allow 192.168.17.0 255.255.255.0
No vpn_ipsec_splitTunnelAcl of the standard access list only allowed 192.168.2.0 255.255.255.0
(2) NAT 0-list of access should also include the traffic between the local subnet to the Pool of IP VPN:
Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.2.0 255.255.255.0
(3) dynamic-map has not been created and assigned to crypto card:
Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-SHA
card crypto ipsec WAN_map 65000-isakmp dynamic dynmap
(4) Finally, you have not enabled protocol IPSec in your group strategy:
attributes of the strategy of group vpn_ipsec
Protocol-tunnel-VPN IPSec
Hope that helps.
If it still does not after the changes described above, please kindly share the latest config and also the output of the following debugs when you try to connect:
debugging cry isa
debugging ipsec cry
-
Authentication failure - 5505 8.3 configuration to windows server RAIDUS vpn client
Hello
I'm trying to put up a 5505 (8.3 running) so that I can use vpn client through the RADIUS authentication
I set up a new local RAIDUS windows box and used the ASDM Assistant and a few other installation guides the 5505.
I get the following error:
INFO: Attempt to <10.0.0.92>IP address authentication test (timeout: 12 seconds)
ERROR: Authentication rejected: failure of the AAA
any help would be greatly appreciated
Here is my config sanitized:
lit5505-02 # sh run
: Saved
:
ASA Version 8.3 (1)
!
hostname lit5505-02
no names
!
interface Vlan1
nameif inside
security-level 100
10.0.0.100 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
banner motd ****************************************
Banner motd No. unauthorized access is allowed
banner motd ****************************************
passive FTP mode
DNS server-group DefaultDNS
domain name
network obj_any object
subnet 0.0.0.0 0.0.0.0
object network lotus_notes
host 10.0.0.3
network sonicwall_ssl_2000 object
Home 10.0.0.12
network of the NETWORK_OBJ_10.0.0.0_24 object
10.0.0.0 subnet 255.255.255.0
network of the ABD_LAN object
10.7.0.0 subnet 255.255.0.0
network of the LIT_LAN object
10.0.0.0 subnet 255.255.0.0
network of the LIT_LAN_vlan101 object
subnet 10.0.1.0 255.255.255.0
network of the LIT_LAN_vlan102 object
10.0.2.0 subnet 255.255.255.0
network of the LIT_LAN_vlan103 object
subnet 10.0.3.0 255.255.255.0
network of the LIT_LAN_vlan104 object
10.0.4.0 subnet 255.255.255.0
network of the LIT_LAN_vlan105 object
10.0.5.0 subnet 255.255.255.0
network of the LIT_LAN_vlan106 object
10.0.6.0 subnet 255.255.255.0
network of the LIT_LAN_vlan109 object
10.0.9.0 subnet 255.255.255.0
network of the LIT_LAN_vlan112 object
10.0.112.0 subnet 255.255.255.0
network of the LIT_LAN_vlan114 object
10.0.114.0 subnet 255.255.255.0
network of the LIT_LAN_vlan120 object
10.0.20.0 subnet 255.255.255.0
network of the LIT_LAN_vlan121 object
10.0.21.0 subnet 255.255.255.0
network of the LIT_LAN_vlan100 object
10.0.0.0 subnet 255.255.255.0
network of the LIT_LAN_vlan107 object
10.0.7.0 subnet 255.255.255.0
network of the LIT_LAN_vlan108 object
10.0.8.0 subnet 255.255.255.0
network of the BER_vlan1 object
subnet 10.8.0.0 255.255.255.0
the LIT_VLANS object-group network
network-object, object LIT_LAN_vlan100
network-object, object LIT_LAN_vlan101
network-object, object LIT_LAN_vlan102
network-object, object LIT_LAN_vlan103
network-object, object LIT_LAN_vlan104
network-object, object LIT_LAN_vlan105
network-object, object LIT_LAN_vlan106
network-object, object LIT_LAN_vlan107
network-object, object LIT_LAN_vlan108
network-object, object LIT_LAN_vlan109
network-object, object LIT_LAN_vlan112
network-object, object LIT_LAN_vlan114
network-object, object LIT_LAN_vlan120
network-object, object LIT_LAN_vlan121
the BER_VLANS object-group network
network-object, object BER_vlan1
access list off - in extended permit icmp any one
out-in access-list extended permit tcp any object sonicwall_ssl_2000 eq https
access-list out-in extended permit tcp any eq smtp lotus_notes object
access list-based ip allowed any one
outside_1_cryptomap list extended access permitted ip LIT_VLANS object ABD_LAN object-group
outside_2_cryptomap list extended access permitted ip object-group LIT_VLANS-group of objects BER_VLANS
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT static LIT_VLANS LIT_VLANS destination (indoor, outdoor) static source ABD_LAN ABD_LAN
NAT static LIT_VLANS LIT_VLANS destination (indoor, outdoor) static source BER_VLANS BER_VLANS
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
object network lotus_notes
Static NAT (indoor, outdoor)
network sonicwall_ssl_2000 object
Static NAT (indoor, outdoor)
Access-group all-out in the interface inside
out-in access-group in external interface
Route outside 0.0.0.0 0.0.0.0
Route inside 10.0.1.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.2.0 255.255.255.0 10.0.0.254 1
Route inside between 10.0.3.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.4.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.5.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.6.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.7.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.8.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.9.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.20.0 255.255.255.0 10.0.0.254 1
Route inside 10.0.21.0 255.255.255.0 10.0.0.254 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server litvms03
litvms03 AAA-server (inside) host 10.0.0.92
key *.
RADIUS-common-pw *.
the ssh LOCAL console AAA authentication
Enable http server
http 10.0.0.0 255.255.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
map 1 set outside_map crypto peer
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 2 match address outside_2_cryptomap
card crypto outside_map 2 pfs Group1 set
card crypto outside_map 2 defined peer
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet timeout 5
SSH 10.0.0.0 255.255.0.0 inside
SSH 10.7.0.0 255.255.0.0 inside
SSH timeout 5
SSH version 2
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 216.14.98.234 prefer external source
NTP server 204.15.208.61 prefer external source
WebVPN
internal jdr_littleport_employee_vpn group policy
attributes of the strategy of group jdr_littleport_employee_vpn
banner value
value of 10.0.0.8 WINS server 10.100.1.141
value of 10.0.0.8 DNS server 10.100.1.141
Split-tunnel-policy tunnelall
jdrcables.com value by default-field
Split-dns value jdrcables.com
IPv6 address pools no
type of tunnel-group ipsec-l2l
Tunnel ipsec-attributes group
pre-shared key *.
type of tunnel-group ipsec-l2l
Tunnel ipsec-attributes group
pre-shared key *.
!
!
context of prompt hostname
Cryptochecksum:6d1868630c83f17fe0c7de41006a1526
: end
Rich
I have checked the road conditions but missed the VIRTUAL LAN address. Sorry about that.
I'm glad to see that you solved the problem and am not surprised that the question seems to have been some incompatible in the serttings server. I think you should be able to close the thread based on your response. Give it a try.
HTH
Rick
-
Cisco VPN Client cannot ping from LAN internal IP
Hello
I apologize in advance for my lack of knowledge about it, but I got a version of the software running ASA 5510 7.2 (2) and has been invited to set up a site with a client, I managed to get this configured and everything works fine. In addition, I created a group of tunnel ipsec-ra for users to connect to a particular server 192.168.10.100/24 remote, even if the connection is made successfully, I can not ping any IP on the LAN 192.168.10.0/24 located behind the ASA and when I ping inside the interface on the ASA it returns the public IP address of the external interface.
If someone out there could give me a little push in the right direction, it would be much appreciated! This is the current configuration of the device.
Thanks in advance.
: Saved
:
ASA Version 7.2 (2)
!
hostname ciscoasa5510
domain.local domain name
activate the password. 123456789 / encrypted
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group ISP
12.34.56.789 255.255.255.255 IP address pppoe setroute
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
passwd encrypted 123456789
passive FTP mode
clock timezone GMT/UTC 0
summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS server-group DefaultDNS
domain.local domain name
permit outside_20_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124
access-list Split_Tunnel_List note the network of the company behind the ASA
Split_Tunnel_List list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
IP local pool domain_vpn_pool 192.168.11.1 - 192.168.11.254 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 12.34.56.789 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
internal domain_vpn group policy
attributes of the strategy of group domain_vpn
value of 212.23.3.100 DNS server 212.23.6.100
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Split_Tunnel_List
username domain_ra_vpn password 123456789 encrypted
username domain_ra_vpn attributes
VPN-group-policy domain_vpn
encrypted utilisateur.123456789 password username
encrypted utilisateur.123456789 password username
privilege of username user password encrypted passe.123456789 15
encrypted utilisateur.123456789 password username
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 set pfs
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
peer set card crypto outside_map 20 987.65.43.21
outside_map crypto 20 card value transform-set ESP-3DES-SHA
3600 seconds, duration of life card crypto outside_map 20 set - the security association
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 987.65.43.21 type ipsec-l2l
IPSec-attributes tunnel-group 987.65.43.21
pre-shared-key *.
tunnel-group domain_vpn type ipsec-ra
tunnel-group domain_vpn General-attributes
address domain_vpn_pool pool
Group Policy - by default-domain_vpn
domain_vpn group of tunnel ipsec-attributes
pre-shared-key *.
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 5
Console timeout 0
VPDN group ISP request dialout pppoe
VPDN group ISP localname [email protected] / * /
VPDN group ISP ppp authentication chap
VPDN username [email protected] / * / password *.
dhcpd dns 212.23.3.100 212.23.6.100
dhcpd lease 691200
dhcpd ping_timeout 500
domain.local domain dhcpd
!
dhcpd address 192.168.10.10 - 192.168.10.200 inside
dhcpd allow inside
!
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:1234567890987654321
: end
Hello
Seems to me that you are atleast lack the NAT0 configuration for your VPN Client connection.
This configuration is intended to allow the VPN Client to communicate with the local network with their original IP addresses. Although the main reason that this is necessary is to avoid this traffic to the normal rule of dynamic PAT passing this traffic and that traffic is falling for the corresponding time.
You can add an ACL rule to the existing ACL NAT0, you have above and the NAT configuration should go next
Add this
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
Hope this helps
Let me know how it goes
-Jouni
-
Problems to connect via the Cisco VPN client IPSec of for RV180W small business router
Hello
I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for
> [34360] has no config mode. I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.
Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.
Router log file (I changed the IP
addresses > respectively as well as references to MAC addresses) Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart
> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT> [44074] because it is admitted only after the phase 1.
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [4500]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for> [4500] - > [44074] with spi = >.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP>
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP>
Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for> [4500] - > [44074] with spi = > The router configuration
IKE policy
VPN strategy
Client configuration
Hôte : < router="" ip=""> >
Authentication group name: remote.com
Password authentication of the Group: mysecretpassword
Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)
Username: myusername
Password: mypassword
Please contact Cisco.
Correct, the RV180 is not compatible with the Cisco VPN Client. The Iphone uses the Cisco VPN Client.
You can use the PPTP on the RV180 server to connect a PPTP Client.
In addition, it RV180 will allow an IPsec connection to third-party customers 3. Greenbow and Shrew Soft are 2 commonly used clients.
-
AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2
Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type
Type of TG_TEST FW1 (config) # tunnel - group?
set up the mode commands/options:
Site IPSec IPSec-l2l group
Remote access using IPSec-IPSec-ra (DEPRECATED) group
remote access remote access (IPSec and WebVPN) group
WebVPN WebVPN Group (DEPRECATED)FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
FW1(config-tunnel-IPSec) #?configuration of the tunnel-group commands:
any required authorization request users to allow successfully in order to
Connect (DEPRECATED)
Allow chain issuing of the certificate
output attribute tunnel-group IPSec configuration
mode
help help for group orders of tunnel configuration
IKEv1 configure IKEv1
ISAKMP policy configure ISAKMP
not to remove a pair of attribute value
by the peer-id-validate Validate identity of the peer using the peer
certificate
negotiation to Enable password update in RADIUS RADIUS with expiry
authentication (DEPRECATED)FW1(config-tunnel-IPSec) # ikev1?
the tunnel-group-ipsec mode commands/options:
pre-shared key associate a key shared in advance with the connection policyI'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)
Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..
But it would be nice to have a bit more security on VPN other than just the connections of username and password.
If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?
If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?
I really hope that something like this exists still!
THX,
WR
You are welcome
In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.
With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.
-
The VPN client VPN connection behind other PIX PIX
I have the following problem:
I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).
So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5
I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.
Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.
If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:
305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x
194.x.x.x is our customer s address IP PIX
I understand that somewhere access list is missing, but I can not understand.
Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.
Can you please help me?
Thank you in advan
The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.
I've cut and pasted here for you to read, I think that the problem mentioned below:
Question:
Hi Glenn,.
Following is possible?
I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.
The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?
My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.
Thank you very much for any help provided in advance.
Response from Glenn:
First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:
fixup protocol esp-ike
See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.
If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:
ISAKMP nat-traversal
See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.
NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.
ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.
A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.
NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.
Hope that helps.
-
Win 7 VPN client cannot access remote resources beyond the VPN server
I have a Win 7 laptop with work and customer Win 7 VPN set up, and through it that I can access everything allowed resources on the remote network.
I built a new computer, set up the Win 7 client with the exact same parameters everywhere, connected to the VPN with success, but can not access any of the resources on the remote network that I can on my laptop.
Win 7 64 bit SP 1
I did research online and suggestions have already had reason of my new set up. In addition, I have a second computer that I've set up the VPN client, and I'm having the same problem. VPN connects successfully, but is unable to access the resources.
Tested with firewall off the coast.
Troubleshooting Diagnostic reports: your computer seems to be configured correctly, distance resources detected, but not answered do not.
I created another VPN client on the new computer to another remote network and everything works perfectly.
Remember the old VPN connection to the remote network that does not work on the new computer works perfectly on Win 7 64 bit laptop computer.
So, what do I find also different between identical configurations "should be" where we work and two new machines is not?
It must be something stupid.
Hello
This question is more suited for a TechNet audience. I suggest you send the query to the Microsoft TechNet forum. See the link below to do so:
https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworkingPlease let us know if you have more queries on Windows.
Maybe you are looking for
-
Where did "recently marked with a bookmark?
Since the upgrade to 13 FF I have recently bookmarked in my drop down list more.He uses a lot and miss me him! Also recently synced my FF between desktop and laptop, does that take away "recent bookmarks"? Thank you!
-
What is the latest version of IMovie
Hello I have version 10.1.1 race on my Mac OS X 10.11.4. Hard to find manuals or instructions. This is the latest version of IMovie?
-
Satellite A100-680: PnP BIOS Extension missing driver
I searched for about one hour now, other threads from reading and the search manually through the database of the driver, but I can't find any useful information. As you can see from the following screenshot...[http://img528.imageshack.us/img528/3171
-
J3Z14PA #ABG: is it possible to change the display on HP Envy 15 Q004TX Panel
The laptop has initially complete 720 p. is it possible to change the Panel of slab IPS 1080 p? It's touchsmart and what is the display for q004tx part number? Kind regards
-
I can not configure Windows messenger in Windows XP
I have installed Windows XP system. I could not configure windows messenger to communicate with my colleagues. When I checked the tools-> Options-> tab accounts, I couldn't find the account of SIP communications service with which others have configu