Debug problems using EPCO, zipalign.exe file not found

Similar Questions

• After the closure of Windows XP on my medion Tower desktop computer it now primer not. The message I get is Retten.exe file not found.

  I have a Medion Tower Office that, like fine until this last time, I closed Windows and now won't start or switch to safe mode recovery mode, ect., the message I get is unable to find the retten.exe file. It will not allow even me to re - install Windows xp from the disk that came with the desktop computer. Can any help?

  Thank you

  Hello

  ·        You did changes to the computer before you shut down the computer?

  You can try to boot from the CD and perform a disk check, and check if that helps. You will need to change the boot order in the BIOS (Basic Input/output System) and check if that helps.

  Warning: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Start Recovery console, and then run the disk check. To start Recovery console follow the link below.

  http://support.Microsoft.com/kb/314058

  Note: To start the recovery console, you need the Windows XP installation CD.

  Once you start in the recovery console, follow the link to perform the disk check.

  http://support.Microsoft.com/kb/315265

  You may need to contact the manufacturer for support.

  http://support.medionusa.com/

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• error-17500 when you use the version selector and the toolboxinstaller.exe file not found since the deployment of ts3.5

  Whenever I run the version selector to switch between ts4.2 and 3.5, it displays the error message above and gives also advice how to fix for a version of visual studio, I do not have (I am using 2003). As well as this when I start the deployment of TS3.5 engine I get error message with toolboxinstaller.exe system.io.filenotfound. I know that they are then tried to repair/reinstall nothing works, any help would be greatly appreciated thanks

  Hi Elizabeth,.

  The message below is similar to the message that you receive (note that this message relates to Visual Studio 2005, you could relate to Visual Studio 2003):

  

  This is a known issue with Version TestStand selector and was reported to R & D (#171620). The picker Version TestStand assumes that when Visual Studio is installed on the machine, that Visual C++ has also been installed. It tries to write in Visual C++ specific files that do not exist if Visual C++ is not installed.

  This error does not mean that something is not necessarily, it is more a message that the file cannot be written in successfully. You should be able to continue to launch TestStand successfully without problem.

  On the deployment utility, I suppose that the two issues are related, however, it would be much easier to say for certain that the error you receive won't cause problems if you post a screenshot of the error. You can do it.

  Thank you!

• start-up in win xp that I got the error as "system3_.exe" file not found, search... what kind of error is? Please help me.

  I searched a lot on the internet, but nowhere I found the solution, if you can solve it please reply post.

  Something you installed was not installing correctly.

  Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx --> here

  Install Autoruns, then run it.  Wait until the analysis is completed (as shown in the lower left corner) and then click on the tab 'connection '.  Browse the entries in the right column ("path of the Image) for an entry that includes"system3_.exe ".  When you find it, uncheck the box at the left end of the line and restart your computer.  The error should appear is no longer.

  If you can't find "system3_.exe" on the connection tab, click the "all" tab.  Then click on file > find to search for "system3_.exe."

  I would be interested to learn what caused this particular problem, so when you find the entry, please right click on it and select copy.  Then paste an answer here.

• I can't access some websites using Firefox. For my own site, I get "file not found". My Yahoo downloads in the form of text. No problems with browsers IE or Chrome

  I can't access some websites using Firefox. Pages say "File not found" or in the case of Yahoo and Facebook, they resemble the on-screen text files. No problems with my computer and it is not the case with my browsers IE and Chrome. Already deleted and reinstalled Firefox and it has not solved the problem

  You can also do a check of malware with some digitization programs of malicious software on the Windows computer.
  
  Please scan with all programs, because each program detects a different malicious program.
  
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender: Home Page:
    http://www.Microsoft.com/Windows/products/winfamily/Defender/default.mspx
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

• I come from components to build a new computer. Try to use the Windows XP Pro computer old version but after BIOS and XP installation I get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. "What should I do?

  New components is a new computer.
  Inserted the XP Pro CD in the drive but get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. »
  Rebooted comp 5 times with the same problem after BIOS.

  Hi Milkshake83,

  Thanks for posting. Proceed as follows for this error.

  Method 1: Restore the default settings of the BIOS WARNING: this procedure may involve changing the semiconductor (CMOS) settings of the computer's complementary metal oxide and by changing the BIOS of the computer. Incorrect changes to the BIOS of your computer can result in serious problems. Change the CMOS settings of the computer at your own risk.

  To resolve this issue, restore the BIOS of the computer to its default settings. For more information about the correct settings of the BIOS of the computer and how to check and change these settings, see the computer documentation or contact the manufacturer of the computer.

  In addition, to confirm that the computer's BIOS is current, contact the computer manufacturer to inquire about the last update of the BIOS available for the computer.

  Back to top

  Method 2: Remove the faulty RAM to resolve this issue, remove the memory modules installed in the computer.

  NOTE: you must leave enough RAM for the computer to start and run Windows.

  For more information on the amount of RAM that is required to run Windows, click on the number below to view the article in the Microsoft Knowledge Base:

  304297 configuration (http://support.microsoft.com/kb/304297/) System requirements for Microsoft Windows 2000 operating systems

  If the error message described in the "Symptoms" section of this article appears again after removing the memory module, remove a different memory module. This procedure may ask you to restart your computer several times to identify the specific memory module that is not working properly.

  For more information about how to add and remove RAM to the computer, contact the manufacturer of your computer or see the documentation that came with your computer.

  http://support.Microsoft.com/kb/318729

  I hope this helps!
  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• LoadPanel fails with error-94 file not found code unless I am in debug mode

  I've written a dll that has a number of panels in a .uir file.

  When I have it, debug using "debug SeqEdit.exe", everything works fine.

  But, if I just use "run SeqEdit.exe" (without debugging and using the same sequence file, I get the error message:)

  "Error in the call to LoadPanel.

  Handle of parent of Panel: 0,

  The IUR filename: HiPot.uir.

  Resource Panel ID: 4.

  Error code:-94

  File not found. "

  The IUR file is always in the same place, the only difference is that I do not use the debug option.

  It's probably something simple I've forgotten?

  You should not use LoadPanelEx in this case?

• RUNDLL32. EXE. FILE NOT FOUND...

  When I try to use one of my applications, I is the RUNDLL32. EXE. File not found, or I get a window 'open with' appearing aways. I can't even download a "Fixit Solutions" because of the window "open with." Can you help me please?

  Hello

  1. Since when are you facing this problem?
  2 have had changes made prior to this issue?

  Try the following steps:

  Step 1:

  Put the computer in a clean boot state and then try to run programs
  a. put your system in start mode state minimum helps determine if third-party applications or startup items are causing the problem.

  b. refer to the KB Microsoft article below for more information on how to solve a problem by performing a clean boot in XP:

  How to configure Windows XP to start in a "clean boot state"?
  http://support.Microsoft.com/kb/310353

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in the "steps to configure Windows to use a Normal startup state" section in the article above.

  Step 2:

  If the problem persists, I highly recommend to run the Virus Scan. Then follow link below

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• problem running programs and .exe files

  computer has been corrupted (by clicking on kids')-tried malwarebytes' anti-malware scan, when I rebooted, nothing works.  I tried microsoft security, but could not access the program.  I tried the system restore, but that no longer works.  If I try to download a program, do not automatically work .exe files and my computer asks me what kind of program to run it - nothing done!  I am missing shortcuts, applications, and system files.  I can't go to the Help Center to try a new date of system restore because application helpctr.exe is not found.  Any help?

  It is likely that your .exe and other extensions have changed my virus/malware.

  There is a simple fix as long as you can open regedit from the start > run box.

  As long as you can then go (I hope I'm not breaking rules here - url not mine but very helpful)

  http://www.dougknox.com/XP/file_assoc.htm

  Download the .reg and .exe association fixes. Use ' file > import ' option in regedit for each of the downloaded files. This should solve your problems. Best regards, Dave.

• Lsass.exe - Unable to locate component. This application has failed to start because the oleaut32.dll file not found

  Original title: oleaut32.dll xp

  My system XP pro/sp3 does not start normally, without danger or with the original sys disk. I get a message
  Isass.exe - Unable to locate component. This application has failed to start because the oleaut32.dll file not found. reinstalling the application may fix this problem.
  However, I can't in the operating system to do a re-install.
  Any suggestions?

  If c:\windows\system32\oleaut32.dll is missing, you will see messages like this:

  Lsass.exe - Unable to locate component
  This application has failed to start because the OLEAUT32.dll file not found.  Reinstalling the application may fix this problem.

  If the missing file is the only problem, you might have to do a reinstall to fix.

  There should be a copy of Oleaut32.dll in the c:\windows\system32\dllcache folder, so if you can get in the XP Recovery Console, you can just replace it - then you are going to have to start on something to do.

  Once started in the XP Recovery Console, you must enter this command at the prompt:

  Copy c:\windows\system32\dllcache\oleaut32.dll c:\windows\system32

  If the file is not in the dllcache folder (it should really be), depending on your installation, this command can work:

  Copy c:\windows\servicepackfiles\i386\oleaut32.dll c:\windows\system32

  Answered in the affirmative if invited to replace any existing file.

  I don't know what the Microsoft Support Engineer think that KB307545 or KB922371 will help you.  I think that the MSE is just throw a few things to try and some links.  You don't describe symptoms consistent with the need to use one of these methods.   I would say the MSE has never seen this problem before, made no attempt to reproduce the problem, and has no idea how to fix this.

  If your CD does not start in the Recovery Console, or if you don't know what kind of CD do you have to do a CD of XP Recovery Console and boot on it (no media XP required).

  Here's how:

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  After replacing the file, remove the CD and type 'exit' to leave the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• To start XP message get this file xyv.exe is not found.

  QUESTIONS OR COMMENTS
  Message: XP on startup, I get a message this file C:\Documents and Settings\user\eyv.exe is not found. I can't find what program calls this file. A computer search found the following instructions in the file named setupapi.txt under C. Windows.

  2011-01-03 08:11:30 1464.596]
  # 199 Executing "C:\WINDOWS\explorer.exe" with command line: explorer.exe 'C:\Documents and Settings\User\eyv.exe '.
  #W383 'certclas. PNF"migrates: PNF language = 0409, Thread = 1 c 09.
  [2011-01-03 10:44:54 1480.923]
  # 199 Executing "C:\WINDOWS\explorer.exe" with command line: explorer.exe 'C:\Documents and Settings\User\eyv.exe '.
  #W383 "FONTS. PNF"migrates: PNF language = 0409, Thread = 1 c 09.

  It seems that explorer is looking for info on commissioning.

  QUESTIONS OR COMMENTS
  Message: XP on startup, I get a message this file C:\Documents and Settings\user\eyv.exe is not found. I can't find what program calls this file. A computer search found the following instructions in the file named setupapi.txt under C. Windows.

  2011-01-03 08:11:30 1464.596]
  # 199 Executing "C:\WINDOWS\explorer.exe" with command line: explorer.exe 'C:\Documents and Settings\User\eyv.exe '.
  #W383 'certclas. PNF"migrates: PNF language = 0409, Thread = 1 c 09.
  [2011-01-03 10:44:54 1480.923]
  # 199 Executing "C:\WINDOWS\explorer.exe" with command line: explorer.exe 'C:\Documents and Settings\User\eyv.exe '.
  #W383 "FONTS. PNF"migrates: PNF language = 0409, Thread = 1 c 09.

  It seems that explorer is looking for info on commissioning.

  "EYV" seems to be part of a known Trojan virus.  Messages like the one you usually arise when your antivirus application or any other anti-malware partially removed the malware, but left in place the room calling the main malware.

  You may be able to find that trying to launch eyv.exe when connecting using Autoruns .  There is a lot of information presented in Autoruns; focus on the 'Connection' tab

  I suggest that you scan your computer with these tools free anti-malware:

  MalwareBytes Anti-Malware

  SUPERAntiSpyware

  eSet Online Antivirus Scanner (Read the FAQ)

  And you might consider changing your antivirus application.

• I have error msikhd32.dll file not found on startup, how to solve this problem?

  msikhd32.dll

  There was a problem starting msikdh32.dll

  The specified could not be found.

  Hi Vipul,

  Thank you for the question to Microsoft Community. I'll give my best to help you.

  From your problem description, I understand that you receive error msikhd32.dll file not found when starting.

  To better understand the issue, answer the following questions.

  You did changes to the computer before the show?

  You can perform the methods suggested below and check if they will help you solve the problem.

  Method 1: Perform the clean boot, check if you receive the message.

  To do this, follow the steps in this link:

  http://support.Microsoft.com/kb/929135

  NOTE: After you check the clean boot feature configure Windows to use a Normal startup using step 7 proposed in the above mentioned link.

  Method 2: perform the complete analysis of a computer by using the Microsoft Safety Scanner: http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  If the problem persists, or if you want more help respond us. We are happy to help you.

• File not found error when you use agent ODI.

  Hello

  I am trying to load data using the csv file and get the following error.

  ODI-1227: SrcSet0 (load) task fails on the source FILES LOCAL connections.

  Caused by: java.sql.SQLException: ODI-40438: file not found:

  I am going through the oracle blog and discover this ODI agent and the source file must be in the same server. But I can't place t of the file to the server of the odi where the agent is running. Can anyone know how to solve this problem.

  ODI configuration:

  ODI 11.1.1.7

  ODI Linux server

  ODI Client Windows 7.

  Thank you

  P

  Hi Paul.P,

  If you select an agent for execution of your, this agent should have access to all sources of data (DB, files,...) used in your integration project.

  You can map a network drive on the server where the agent is running and move files. Or you can get it from the original location via FTP or sFTP, for example. But your server must be able to manage this file at some point, if you want to use.

  If there is no way you can have the files on this server, you must take the opposite approach and install a new agent, where the files are located.

  More information: http://www.ateam-oracle.com/understanding-where-to-install-the-odi-standalone-agent/

  Kind regards

  JeromeFr

• Try to reinstall Adobe Photoshop Extended CS5 Win - have downloaded the file, but when I double click on the .exe to install file, I get and which words "Installer could not initialize - file not found" error message can someone help me?

  Try to reinstall Adobe Photoshop Extended CS5 Win - have downloaded the file, but when I double click on the .exe to install file, I get and which words "Installer could not initialize - file not found" error message can someone help me?

  Hi Rose

  Refer to the troubleshooting error messages | CS5, CS5.5 bootstrapper

  Installer [CS5.5] initialization failed. Please download Adobe Support Advisor to detect the problem.

  I hope this helps.

  Thank you

  Varun

• I downloaded Adobe photoshop cs 5, after download, it is not installing in my computer of OS - Windows 7 and the message is to give "Installer failed to initialize. File not found. Download Adobe support Advisor to check the problem

  I downloaded Adobe photoshop cs 5, for trial, after download, it is not installing in my computer of OS - Windows 7 and the message is to give "Installer failed to initialize. File not found. Download Adobe support Advisor to check the problem

  just uninstall cs5, clean a cleaning use of the CC tool to resolve installation problems. CC, CS3 - CS6 then install.

  Make sure your file is downloaded to your hard drive sizes are expected file sizes.  If you don't know how, ask someone to do it for you.