Debugging and telnet

Similar Questions

• Allowing ICMP and Telnet via a PIX 525

  We are trying to build a new block of distribution to our backbone WAN. We are experiencing a problem when establishing ICMP and Telnet via the PIX. The following is known:

  1 Ping and telnet to the 6509 and internal network works very well for the PIX.

  2 Ping the 7206 for the PIX works just fine.

  3 debug normal to see activity track ICMP for connections ICMP for the PIX of the network 6509 and internal; However, the debug shows nothing - no activity - during attempts to ping at a.b.5.18. (see below).

  In short, all connections seem to be fine between the three devices, however, we can get ICMP and Telnet work correctly through the PIX.

  The layout is:

  6509 (MSFC) - PIX 525-7206

  IP:a.b.5.1 - a.b.5.2 a.b.5.17 - a.b.5.18

  255.255.255.0 255.255.255.240 255.255.255.240

  (both)

  networks: a.b.5.0 a.b.5.16

  255.255.255.240 255.255.255.240

  6509:

  interface VlanX

  Description newwan-bb

  IP address a.b.5.1 255.255.255.0

  no ip redirection

  router ospf

  Log-adjacency-changes

  redistribute static subnets metric 50 metric-type 1

  passive-interface default

  no passive-interface Vlan9

  ((other networks omitted))

  network a.b.5.0 0.0.0.255 area 0

  default information are created

  PIX 525:

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif ethernet2 security10 failover

  hostname XXXXXX

  domain XXX.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  access ip-list 102 permit a whole

  access-list 102 permit icmp any one

  access-list 102 permit icmp any any echo

  access-list 102 permit icmp any any echo response

  access-list 102 permit icmp any any source-quench

  access-list 102 permit everything all unreachable icmp

  access-list 102 permit icmp any one time exceed

  103 ip access list allow a whole

  access-list 103 allow icmp a whole

  access-list 103 permit icmp any any echo

  access-list 103 permit icmp any any echo response

  access-list 103 permit icmp any any source-quench

  access-list 103 allow all unreachable icmp

  access-list 103 allow icmp all once exceed

  pager lines 24

  opening of session

  timestamp of the record

  logging buffered stored notifications

  interface ethernet0 100full

  interface ethernet1 100full

  interface ethernet2 100full

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  IP address outside a.b.5.17 255.255.255.240

  IP address inside a.b.5.2 255.255.255.240

  failover from IP 192.168.230.1 255.255.255.252

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group 103 in external interface

  Route outside 0.0.0.0 0.0.0.0 a.b.5.18 1

  Route inside a.0.0.0 255.0.0.0 a.b.5.1 1

  Inside a.b.0.0 255.240.0.0 route a.b.5.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet a.0.0.0 255.0.0.0 outdoors

  Telnet a.0.0.0 255.0.0.0 inside

  Telnet a.b.0.0 255.240.0.0 inside

  Telnet a.b.5.18 255.255.255.255 inside

  Telnet timeout 5

  SSH timeout 5

  Terminal width 80

  Recognizing any help on proper routing through a PIX 525, given that all this is for a network internal.

  on the 6509, why the int has a 24 subnet mask, when everything has a 28? If you try the 6500 ping.18, he thinks that it is on a local network, and there no need to route through the pix

  Your access lists are confusing.

  access-list # ip allowed any one should let through, and so everything that follows are redundant statements.

  for the test,.

  alloweverything ip access list allow a whole

  Access-group alloweverything in interface outside

  should the pix act as a router - you are effectively disabling all firewall features.

• SSH and Telnet access for catalyst 4503 list

  I was wondering the structure of command to apply an access list to ssh and telnet on a catalyst 4503. I keep a list of access for indoors and outdoors. Can afford two different IPs from the outside? Thank you

  You will need create an access list indicating the networks/hosts that you want to allow.

  -Example

  access-list 10 permit 10.10.1.10

  access-list 10 permit 10.10.2.10

  access-list 10 permit 127.1.0.0 0.0.255.255

  access-list 10 permit 192.168.1.0 0.0.0.255

  So you want to put this list of access on the VTY interfaces.

  -Example

  line vty 0 4

  access-class 10

  entry ssh transport * if you only want to SSH *.

  line vty 5 15

  access-class 10

  entry ssh transport * Ditto *.

  Now you can do all this with * line vty 0 15 * but, it gives you a better idea of what is happening. It is a simplistic configuration. Remember that it is advisable not to allow ssh. If you want to allow at the same time, let him * transport input ssh * out of the configuration.

  I hope that gives you an idea of the structure. If this is not the case, let me know.

• How to debug and find the exact constraint violation error

  {14:22:36:ErrorCode 122712 - 1 with ErrorMessage as ORA-00001: unique constraint (OPS$ CMS.)} {PK_TB_ML_EXER_UPLOAD) violated appeared [SSO16063259009], pk_xop_subsales.pr_process_exer [CMSCOST_USER]}
  
  {Pr_process_exer (PROCEDURE)
  p_voucher_num tb_xop_order_manager_t.voucher_num%TYPE,
  p_status_type tb_xop_order_manager_t.status_type%type,
  p_dest tb_xop_order_manager_t.dest%type,
  p_reference_key tb_xop_order_manager_t.reference_key%type,
  p_seq_num tb_xop_order_manager_t.seq_num%type,
  p_return_code tb_xop_order_manager_t.return_code%type,
  p_reason_desc tb_xop_order_manager_t.reason_desc%type,
  p_activity_qty tb_xop_order_manager_t.activity_qty%type,
  p_leaves_qty tb_xop_order_manager_t.leaves_qty%type,
  p_exec_price tb_xop_order_manager_t.exec_price%type,
  p_current_status tb_xop_order_manager_t.current_status%type,
  p_err_cur ON ref_cursor)
  IS
  CURSOR get_order_dtls (v_voucher_num tb_xop_order_manager_t.voucher_num%type)
  IS
  SELECT *.
  OF tb_xop_order_manager_t
  WHERE voucher_num = v_voucher_num;
  
  CURSOR get_mail_cd (v_opt_num OPTIONEE.opt_num%TYPE) IS
  SELECT mail_cd, sp_mail_cd
  OF XOP_OPTIONEE
  WHERE opt_num = v_opt_num;
  
  cursor get_opt_dtls (v_opt_num OPTIONEE.opt_num%TYPE) IS
  Select
  SUBSTR (Trim (O.name_first) |) ' ' || Trim (O.name_mi) | ' ' ||
  Trim (O.name_last), 1: 35) p_name,.
  SUBSTR (O.address1, 1, 35) opt_addr1,.
  SUBSTR (O.address2, 1, 35) opt_addr2,.
  SUBSTR (O.address3, 1, 35) opt_addr3,.
  SUBSTR (O.address4, 1, 35) opt_addr4,.
  SUBSTR (O.address5, 1, 35) opt_addr5,.
  SUBSTR (O.address6, 1, 35) opt_addr6,.
  SUBSTR (Trim (O.City) |) ' ' || Trim (O.State) | ' ' ||
  Trim (O.zip) | ' ' || Trim (O.Country), 1: 35) city_state_zip_country,.
  Trim town (O.City),
  Trim (O.State) State,
  Trim (O.zip) zip,
  Trim (O.Country) countries
  of the option o holder
  where o.opt_num = v_opt_num;
  -CQ: PCTUP00210726 - added wire instructions audit for info thread deleted.
  CURSOR (c_wire_instruction)
  in_wire_seq_no TB_XOP_WIRE_INSTRUCTIONS.wire_seq_no%TYPE) IS
  SELECT ml_brok_acct_num,
  SSN,
  plan_num,
  instr_type,
  aba_routing_num,
  swift_routing_code,
  bank_name,
  bank_acct_num,
  name_on_account,
  bank_addr_1,
  bank_addr_2,
  bank_addr_3,
  City,
  State,
  countries,
  zip,
  bank_ident_num,
  addtl_info
  OF TB_XOP_WIRE_INSTRUCTIONS
  WHERE wire_seq_no = in_wire_seq_no
  UNION
  SELECT ml_brok_acct_num,
  SSN,
  plan_num,
  instr_type,
  aba_routing_num,
  swift_routing_code,
  bank_name,
  bank_acct_num,
  name_on_account,
  bank_addr_1,
  bank_addr_2,
  bank_addr_3,
  City,
  State,
  countries,
  zip,
  bank_ident_num,
  addtl_info
  OF TB_XOP_WIRE_INSTRUCTIONS_AUDIT
  WHERE wire_seq_no = in_wire_seq_no;
  
  CURSOR c_order_qty IS
  SELECT order_qty
  OF tb_xop_order_manager
  WHERE voucher_num = p_voucher_num;
  v_order_qty tb_xop_order_manager.order_qty%TYPE;
  
  v_wire_instruction c_wire_instruction % ROWTYPE;
  v_order_dtls get_order_dtls % rowtype;
  v_opt_dtls get_opt_dtls % rowtype;
  v_settle_dt tb_ml_exer_upload.settle_dt%type;
  v_cusip_num corp.cusip_num%type;
  number of v_err_cd (12): = 0;
  v_err_msg varchar2 (4000);
  v_compy_nme tb_fc_Compy.compy_nme%type;
  v_ml_sec_num tb_fc_compy.ml_sec_num%type;
  v_mail_cd xop_optionee.mail_cd%type;
  v_count1 PLS_INTEGER: = 0;
  v_sum_activity_qty tb_xop_order_manager_t.activity_qty%TYPE;
  v_transact_no PLS_INTEGER;
  
  v_ivr_plan_num tb_fc_compy.ivr_plan_num%TYPE;
  
  wait_for_more EXCEPTION;
  exceeds_order_qty EXCEPTION;
  -Added CQ # PCTUP00481233
  number of v_sub_totfee;
  number of v_sub_fixedfee1;
  number of v_sub_fixedfee2;
  number of v_sub_fixedfee3;
  number of v_sub_secfee;
  number of v_sub_feenum;
  -Added CQ # PCTUP00481233
  v_fixedfee1 tb_xop_order_manager_t.fixed_fee1%TYPE; -SPIF # 43161 - variable to contain the fixed mensuels1
  
  BEGIN
  
  OPEN c_order_qty.
  SEEK c_order_qty INTO v_order_qty;
  CLOSE C_order_qty;
  DBMS.output.put_line ('completed1');
  IF v_order_qty <>p_activity_qty THEN
  DBMS.output.put_line ('completed2');
  IF p_status_type = "EO" AND v_order_qty < p_activity_qty THEN
  RAISE exceeds_order_qty;
  DBMS.output.put_line ('completed3');
  ELSIF p_status_type = 'EO' AND v_order_qty > p_activity_qty THEN
  -Partial enforcement
  INSERT INTO tb_xop_hold_multi_orders
  (voucher_num
  reference_key
  seq_num
  return_code
  reason_desc
  status_type
  activity_qty
  leaves_qty
  exec_price
  current_status
  waiting
  activ_dt)
  VALUES
  (p_voucher_num
  p_reference_key
  p_seq_num
  p_return_code
  p_reason_desc
  p_status_type
  p_activity_qty
  p_leaves_qty
  p_exec_price
  p_current_status
  , 'Y'
  SYSTIMESTAMP);
  DBMS.output.put_line ('completed4');
  ON THE OTHER
  IF p_status_type = "BE" THEN
  SELECT COUNT (1) IN v_count1
  OF tb_xop_hold_multi_orders
  WHERE voucher_num = p_voucher_num;
  DBMS.output.put_line ('completed5');
  IF v_count1 > 0 THEN
  INSERT INTO tb_xop_hold_multi_orders
  (voucher_num
  reference_key
  seq_num
  return_code
  reason_desc
  status_type
  activity_qty
  leaves_qty
  exec_price
  current_status
  waiting
  activ_dt)
  VALUES
  (p_voucher_num
  p_reference_key
  p_seq_num
  p_return_code
  p_reason_desc
  p_status_type
  , (-1) * p_activity_qty
  p_leaves_qty
  p_exec_price
  p_current_status
  , 'Y'
  SYSTIMESTAMP);
  UPDATE tb_xop_hold_multi_orders
  QUEUE = 'Y '.
  WHERE voucher_num = p_voucher_num;
  DBMS.output.put_line ('completed6');
  END IF;
  END IF;
  END IF;
  DBMS.output.put_line ('completed7');
  SELECT SUM (NVL(activity_qty,0)) IN the v_sum_activity_qty
  OF tb_xop_hold_multi_orders
  When pending = 'Y '.
  AND voucher_num = p_voucher_num;
  
  IF v_sum_activity_qty > 0 THEN
  IF v_sum_activity_qty <>v_order_qty THEN
  RAISE wait_for_more;
  ON THE OTHER
  -final order in the case of partial performance; complete the process
  UPDATE tb_xop_hold_multi_orders
  PUT on hold = ' don't
  process_dt = SYSDATE
  WHERE voucher_num = p_voucher_num;
  END IF;
  END IF;
  END IF;
  
  UPDATE tb_xop_order_manager_t
  SET activ_dt = TO_CHAR (SYSDATE, "YYYY-MM-DD HH24:MI:SS") | '. 000'
  dest = p_dest
  reference_key = p_reference_key,
  seq_num = p_seq_num
  return_code = p_return_code
  reason_desc = p_reason_desc,
  status_type = p_status_type
  , activity_qty = v_order_qty - p_activity_qty
  , leaves_qty = 0 - p_leaves_qty
  exec_price = p_exec_price,
  WHERE voucher_num = p_voucher_num;
  DBMS.output.put_line ('completed8');
  /*
  * SPIF # 43161 - update of the current situation to the PO moved to the end, even in works of the PROD.
  */
  
  IF (p_status_type = "EO") THEN
  
  BEGIN
  Select cusip_num
  in v_cusip_num
  Corp;
  EXCEPTION
  WHEN NO_DATA_FOUND THEN
  SELECT cusip_num
  IN v_cusip_num
  OF tb_xop_espp_compy
  WHERE compy_acronym = replace (replace(user,'CMS'), '_USER');
  WHILE OTHERS THEN
  NULL;
  END;
  
  Select compy_nme, ml_sec_num, ivr_plan_num
  in v_compy_nme, v_ml_sec_num, v_ivr_plan_num
  of tb_fc_compy
  where compy_acronym = replace (replace(user,'CMS'), '_USER')
  UNION ALL
  Select compy_nme, je_ml_security_number, ivr_plan_num
  of tb_xop_espp_compy
  where compy_acronym = replace (replace(user,'CMS'), '_USER');
  -where ivr_plan_num = replace (substr(p_voucher_num,1,7), 'NORTH', 'XOP');
  
  Open get_order_dtls (p_voucher_num);
  SEEK get_order_dtls INTO v_order_dtls;
  
  v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_order_dtls.exer_date + 1));
  v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_settle_dt + 1));
  v_settle_dt: = fn_xop_bankopen_bizday (TRUNC (v_settle_dt + 1));
  
  FOR c_mail_cd IN get_mail_cd (v_order_dtls.opt_num)
  LOOP
  v_mail_cd: = c_mail_cd.mail_cd;
  -We need get sp_mail_cd and overlay with the sp_mail_cd in order_manager_t?
  END LOOP;
  
  OPEN get_opt_dtls (v_order_dtls.opt_num);
  SEEK get_opt_dtls INTO v_opt_dtls;
  CLOSE Get_opt_dtls;
  
  v_fixedfee1: = nvl (v_order_dtls.fixed_fee1, 0);
  /*
  * SPIF # 43161 - at least one transaction per day fees
  */
  v_fixedfee1: = pk_xop_enh_exerupdate.chrg_tranxfixed_fee (v_fixedfee1,
  v_order_dtls. Symbol,
  v_order_dtls.corp_acronym,
  v_order_dtls.opt_num);
  -Insert in tb_ml_exer_upload
  -Added CQ # PCTUP00481233
  Pk_Xop_Transactmodel.GET_FEE (v_order_dtls. GROUP_ID, v_order_dtls. SVC_ID, 'SQ', v_order_dtls.opts_exer,
  round (v_order_dtls.exec_price, 4), v_sub_totfee, v_sub_fixedfee2, v_sub_fixedfee1,.
  v_sub_fixedfee3, v_sub_secfee, v_sub_feenum, LPAD (v_order_dtls. SSN, 9, 0));
  v_order_dtls.sec_fee: = v_sub_secfee;
  UPDATE tb_xop_order_manager_t
  SET sec_fee = v_sub_secfee
  WHERE voucher_num = p_voucher_num;
  
  DBMS.output.put_line ('completed8');
  -End CQ # PCTUP00481233
  INSERT INTO tb_ml_exer_upload
  (exer_num, exer_seq,
  exer_dt, written_flag, backout_flag, output_line,
  je_flag, opts_exer,
  tot_tax, shrs_sold, comm_value, tot_fee,
  mkt_prc, exer_type, soc_sec,
  name_first, name_mi,
  name_last, check_addr_1, check_addr_2, check_addr_3,
  check_addr_4, check_addr_5, city, state, zip, country,.
  city_state_zip_country,
  p_name, opt_addr1, opt_addr2, opt_addr3, opt_addr4,
  opt_addr5, opt_addr6,
  settle_dt, send_to_citibank_flag,
  dom_chek_distr, foreign_currency_code,
  distribution_method, wire_seq_no,
  cusip_num, ml_retail_account, multi_curr_handling_fee,
  ml_sec_num, corp_name, upd_optionee_addr,
  outbound_flag,-there are N
  corp_symbol, taxwire_approve,-not make applicaplabe
  exersource,
  mail_cd, sp_mail_cd,
  backup_withholding,
  user_id,
  acct_num_othr)
  VALUES (v_order_dtls.exer_num, 0, v_order_dtls.exer_date, 'No', not, NULL,)
  -Would be PG 12/12/05 Changed to fill the resulting je_flag of dom_chek_distr',.
  -PG 16/12/05 I should not be generated for international controls... If 'Y' always
  'Y',-je_flag
  v_order_dtls.opts_exer, 0,-total tax will be 0.
  v_order_dtls.opts_exer, shrs_sold,
  v_order_dtls.comm_value,
  -SPIF # 43161 - replaced nvl (v_order_dtls.fixed_fee1, 0), with v_fixedfee1
  v_fixedfee1 + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), - v_order_dtls.fees_amt,
  round (v_order_dtls.exec_price, 4), v_order_dtls.exer_type.
  LPAD (v_order_dtls. SSN, 9, '0'),-v_order_dtls.ssn, modified by Suresh on 08/02/07 for SPIF # 37210
  v_order_dtls.name_first, v_order_dtls.name_mi, v_order_dtls.name_last,
  v_order_dtls.check_addr_1, v_order_dtls.check_addr_2, v_order_dtls.check_addr_3,
  v_order_dtls.check_addr_4, v_order_dtls.check_addr_5, NVL (v_order_dtls. City, v_opt_dtls. (City),
  NVL (v_order_dtls. State, v_opt_dtls. State), NVL (v_order_dtls.zip, v_opt_dtls.zip).
  NVL (v_order_dtls. Country, v_opt_dtls. (Country),
  SUBSTR (nvl (v_order_dtls.city | v_order_dtls.)) State | v_order_dtls.zip | v_order_dtls. Country,
  v_opt_dtls.city_state_zip_country), 1: 34),-COLUMN LENGTH MAX IS 35
  v_opt_dtls.p_name, v_opt_dtls.opt_addr1, v_opt_dtls.opt_addr2, v_opt_dtls.opt_addr3,
  v_opt_dtls.opt_addr4, v_opt_dtls.opt_addr5, v_opt_dtls.opt_addr6,
  v_settle_dt, Decode(v_order_dtls.distribution_method,'W','Y','D','Y','C','Y','D'),
  v_order_dtls.dom_chek_distr, v_order_dtls.foreign_currency_code,
  v_order_dtls.distribution_method, v_order_dtls.wire_seq_no,
  v_cusip_num, v_order_dtls.acct_num, v_order_dtls.multi_curr_handling_fee,
  -nvl (fn_get_sec_num (replace (substr (p_voucher_num, 1, 7), 'NORTH', 'XOP'), v_order_dtls.symbol), v_ml_sec_num).
  NVL (fn_get_sec_num (v_ivr_plan_num, v_order_dtls.symbol), v_ml_sec_num).
  v_compy_nme, v_order_dtls.upd_optionee_addr,
  'N'-' is for outgoing flag.
  v_order_dtls. Symbol, 'd', --a ' for disabled taxwires
  The of ', - the of ' source being a subsequent sale.
  v_mail_cd, need to get mail_Cd?
  v_order_dtls.sp_mail_cd, v_order_dtls.backup_withholding,
  (User, v_order_dtls.acct_num_othr);
  
  IF (NVL(v_order_dtls.wire_seq_no,0) > 0) THEN
  
  OPEN c_wire_instruction (v_order_dtls.wire_seq_no);
  SEEK c_wire_instruction INTO v_wire_instruction;
  CLOSE C_wire_instruction;
  
  INSERT INTO TB_XOP_TRANSACT_WIRE_INSTR
  (user_id, exer_num, wire_seq_no, ml_brok_acct_num, ssn,
  plan_num, instr_type, aba_routing_num,
  swift_routing_code, bank_name, bank_acct_num,
  name_on_account, bank_addr_1, bank_addr_2, bank_addr_3,
  City, State, country, zip, bank_ident_num, addtl_info)
  VALUES
  (USER, v_order_dtls.exer_num, v_order_dtls.wire_seq_no,
  v_wire_instruction.ml_brok_acct_num, v_wire_instruction.ssn,
  v_wire_instruction.plan_num, v_wire_instruction.instr_type, v_wire_instruction.aba_routing_num,
  v_wire_instruction.swift_routing_code, v_wire_instruction.bank_name, v_wire_instruction.bank_acct_num,
  v_wire_instruction.name_on_account, v_wire_instruction.bank_addr_1, v_wire_instruction.bank_addr_2,
  v_wire_instruction.bank_addr_3, v_wire_instruction.city, v_wire_instruction.state, v_wire_instruction.country, v_wire_instruction.zip,
  (v_wire_instruction.bank_ident_num, v_wire_instruction.addtl_info);
  DBMS.output.put_line ('completed10');
  END IF;
  
  
  / * PG 05/01/06 call conversion check only for international controls and son * /.
  IF = v_order_dtls.dom_chek_distr ' n AND v_order_dtls.distribution_method IN ('W' ' d ","C"" ") THEN
  / * PG 20/12/05 to treat the subsequent sales with the wire or the distribution of currency * /.
  v_transact_no: = 88;
  pk_xop_citibank_forex.pr_cashconversion_ins_request (v_order_dtls.acct_num
  LPAD(v_order_dtls.ssn,9,'0') - v_order_dtls.ssn, modified by Suresh on 15/02/07 for SPIF # 37210
  v_order_dtls.distribution_method
  v_order_dtls.foreign_currency_code
  v_order_dtls.wire_seq_no
  , TOWER ((v_order_dtls.opts_exer * ronds (v_order_dtls.exec_price, 4)), 2)
  -ROUND(v_order_dtls.comm_value,2)
  -ROUND (nvl(v_order_dtls.fixed_fee1,0) + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), 2)
  -nvl(v_order_dtls.multi_curr_handling_fee,0)
  -product net nvl(v_order_dtls.backup_withholding,0)-
  , v_order_dtls.multi_curr_handling_fee - handling fee
  -Modified by Billon/Suresh on 03/02/2006-, v_order_dtls.login_name
  , CASE v_order_dtls.login_name WHEN ' CUSTOMER /' THEN v_order_dtls.login_name |' SSO' ELSE v_order_dtls.login_name |' / SSO' END
  , v_transact_no - transact_no as a placeholder for the 88 exer_type
  v_order_dtls.check_addr_1
  v_order_dtls.check_addr_2
  v_order_dtls.check_addr_3
  v_order_dtls.check_addr_4
  v_order_dtls.upd_optionee_addr
  v_order_dtls.city
  v_order_dtls.state
  v_order_dtls.zip
  v_order_dtls.country
  v_order_dtls.login_ipaddress
  v_order_dtls.fcnum
  v_order_dtls.opt_num
  v_settle_dt,
  p_exer_num = > v_order_dtls.exer_num
  );
  END IF;
  
  COMMIT;
  
  close get_order_dtls;
  
  END IF;
  
  /*
  * SPIF # 43161 - update of current status in IN. is moved to this part, even PROD.
  */
  UPDATE tb_xop_order_manager_t
  SET exec_dttime = decode (p_status_type, "EO", to_char (sysdate, 'DD-MON-YYYY HH24:mi:ss'), null)
  exer_date = trunc (sysdate)
  , cancel_dttime = decode (p_status_type, 'CX', to_char (sysdate, 'DD-MON-YYYY HH24:mi:ss'), 'UR', to_char (sysdate, "MON-DD-YYYY HH24:mi:ss), null)
  , current_status = "PO."
  sum_status = decode(p_status_type,'EO','X','C'),
  sum_stat_dttime = SYSDATE
  WHERE voucher_num = p_voucher_num;
  
  v_err_cd: = sqlcode;
  v_err_msg: = sqlerrm;
  
  Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
  
  EXCEPTION
  DBMS.output.put_line ('completed200');
  / * PG 02/10 managed 'order of partial fill' exception * /.
  When wait_for_more then
  v_err_cd: = 0;
  v_err_msg: = ' ORA-0000: normal completion, successfully ';
  pr_xop_log_errors (' partially filled;) Pending-activity qty:' | TO_CHAR (v_sum_activity_qty) | "pk_xop_subsales.pr_process_exer");
  Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
  When exceeds_order_qty then
  v_err_cd: = sqlcode;
  v_err_msg: = sqlerrm;
  Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
  pr_xop_log_errors ("exceeded the amount of activity Order_qty - activity qty: ' | ') TO_CHAR (p_activity_qty) | "pk_xop_subsales.pr_process_exer");
  while others then
  v_err_cd: = sqlcode;
  v_err_msg: = sqlerrm;
  Open the p_err_cur for v_err_cd select err_code, v_err_msg err_msg double;
  pr_xop_log_errors (' error code ' | ') SQLCODE |' with ErrorMessage like ' | SQLERRM |' occurred '. the user | (' pk_xop_subsales.pr_process_exer');
  DBMS.output.put_line ('completed125');
  END pr_process_exer;
  }
  
  Hi friends, any1 help me how set ref-cursor in the declaration section and how to find the constraint error situation has occurred...

  956684 wrote:
  Hello.

  Friends please help... How to debug and find the exact position of the constraint violation... Thank you for the help...

  It's not a way to track it unless you have taken the exception raised.

  As a way to start debugging, you will need to monitor
  1. all DML against the Table on which you have constraint. Specifically, the DML that Act on the column you will be forced.
  2. use the exception handling, to record the error and the data that causes the constraint to fail.
  3. don't forget to monitor triggers, if used, could write data in the column you have forced on.

  Or

  Another track is to:

  select *
    from user_source
  where lower(text) like '%your_table_name%';
  order by type, name, line;
  

  Look at the lines, exclude that are in the statement or in the SELECT statements and targets of the DML.

  Looking at the unformatted code, that you have published, this statement looks like a culprit.

  INSERT INTO tb_ml_exer_upload
  (exer_num,exer_seq,
  exer_dt, written_flag, backout_flag, output_line,
  je_flag, opts_exer,
  tot_tax,shrs_sold,comm_value,tot_fee,
  mkt_prc,exer_type, soc_sec,
  name_first, name_mi,
  name_last,check_addr_1,check_addr_2,check_addr_3,
  check_addr_4,check_addr_5,city,state,zip,country,
  city_state_zip_country,
  p_name,opt_addr1,opt_addr2,opt_addr3,opt_addr4,
  opt_addr5,opt_addr6,
  settle_dt,send_to_citibank_flag,
  dom_chek_distr,foreign_currency_code,
  distribution_method,wire_seq_no,
  cusip_num, ml_retail_account,multi_curr_handling_fee,
  ml_sec_num, corp_name,upd_optionee_addr,
  outbound_flag, -- make it N
  corp_symbol,taxwire_approve, -- make it not applicaplabe
  exersource,
  mail_cd, sp_mail_cd,
  backup_withholding,
  user_id,
  acct_num_othr)
  VALUES(v_order_dtls.exer_num,0,v_order_dtls.exer_date,'N','N',NULL,
  -- PG 12/12/05 Changed to populate the je_flag based on dom_chek_distr 'D',
  -- PG 12/16/05 JE should not be generated for international checks.. So 'Y' always
  'Y', --je_flag
  v_order_dtls.opts_exer,0,--total tax will be 0.
  v_order_dtls.opts_exer, --shrs_sold,
  v_order_dtls.comm_value,
  --SPIF# 43161- replaced nvl(v_order_dtls.fixed_fee1, 0) with v_fixedfee1
  v_fixedfee1 + nvl(v_order_dtls.fixed_fee3,0) + nvl(v_order_dtls.sec_fee,0), --v_order_dtls.fees_amt,
  round(v_order_dtls.exec_price, 4),v_order_dtls.exer_type,
  LPAD(v_order_dtls.ssn,9,'0'), --v_order_dtls.ssn, Modified by Suresh on 02/08/07 for SPIF # 37210
  v_order_dtls.name_first,v_order_dtls.name_mi,v_order_dtls.name_last,
  v_order_dtls.check_addr_1,v_order_dtls.check_addr_2,v_order_dtls.check_addr_3,
  v_order_dtls.check_addr_4,v_order_dtls.check_addr_5,nvl(v_order_dtls.city,v_opt_dtls.city),
  nvl(v_order_dtls.state,v_opt_dtls.state),nvl(v_order_dtls.zip,v_opt_dtls.zip),
  nvl(v_order_dtls.country,v_opt_dtls.country),
  SUBSTR(nvl(v_order_dtls.city||v_order_dtls.state||v_order_dtls.zip||v_order_dtls.country,
  v_opt_dtls.city_state_zip_country),1,34), -- COLUMN LENGTH MAX IS 35
  v_opt_dtls.p_name,v_opt_dtls.opt_addr1,v_opt_dtls.opt_addr2,v_opt_dtls.opt_addr3,
  v_opt_dtls.opt_addr4,v_opt_dtls.opt_addr5,v_opt_dtls.opt_addr6,
  v_settle_dt,decode(v_order_dtls.distribution_method,'W','Y','D','Y','C','Y','D'),
  v_order_dtls.dom_chek_distr,v_order_dtls.foreign_currency_code,
  v_order_dtls.distribution_method,v_order_dtls.wire_seq_no,
  v_cusip_num,v_order_dtls.acct_num,v_order_dtls.multi_curr_handling_fee,
  -- nvl(fn_get_sec_num(replace(substr(p_voucher_num,1,7),'SSO','XOP'),v_order_dtls.symbol),v_ml_sec_num),
  nvl(fn_get_sec_num(v_ivr_plan_num, v_order_dtls.symbol),v_ml_sec_num),
  v_compy_nme,v_order_dtls.upd_optionee_addr,
  'N', --'N' is for outbound flag.
  v_order_dtls.symbol,'D', --'D' for taxwires disabled
  'S', -- 'S' for source being subsequent sale.
  v_mail_cd, --need to get mail_Cd??
  v_order_dtls.sp_mail_cd,v_order_dtls.backup_withholding,
  user,v_order_dtls.acct_num_othr);
  

  What is the structure of the tb_ml_exer_upload Table and the columns do you have constraints?
  Which column of the tb_ml_exer_upload table is your primary key (because the constraint name mentions pk_tb_ml_exer_upload)?

  Published by: Jen K on January 4, 2013 12:57

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

• Files dump debugging and log files to install in the disk cleanup window

  The two points above appear in my disk cleanup window, and I wonder if it is o: k to remove. The first occupies a space of 283 KB and the other 2537 KB. The description of these two files in the disk cleanup window is "files created by Windows.

  I have a second question: I have about 5 GB left as free space on my hard drive of 'C '. If this is considered sufficient, or should I get more? I am a senior retired and only use the computer for basic items.

  I have a computer Dell Dimension 4100 with Service Pack 3 for Windows XP - Home Edition Operating System - desktop, 111 Pentium with 930 MHZ, 20 GB hard drive and 512 MB RAM. The file system is FAT 32.

  Thank you very much for your cooperation and your response.

  "Debug dump files" are copies of the contents of your computer's memory.

  When a program crashes, it will sometimes "dump" all or part of the
  contents of the RAM to a file on your hard drive. The file is useful to
  a technical support person who tries to understand why the program
  crashed. (Most of the tech support people have no idea what to do with a dump
  file.)

  Unless you have been asked to submit a dump for inspection file, feel free
  to get rid of them.

  Setup logs files are "log" installation of a program. If you
  Watch a (they are really just text files - open with Notepad) you will have
  see that they give a blow by blow description of how the program has been
  installed, glorious detail.

  If a program does not properly settled, the Setup log will tell you what that
  was wrong. If you have not had a facility wrong, do not hesitate to ditch
  These files as well.

  On the question of how much free space on the disk is enough... There is no
  standards. 15% of your drive must be empty in order for Windows
  The Defragmenter built into the work. In addition, it is to you.
   
  Your processor is another story. It's not easy to find effective security
  software that will work on a P3. Even if you only use the computer
  for the basic elements, an internet connection is pretty basic for a online
  criminal to find you.

  Another response of the community of Windows XP newsgroups

• Difference between Debug and build together and run

  Hello

  I'm new to programming. I have a doubht. What is the difference between the two generation and execution (Alt + F5) and Debug (F5). Can we execute line by line? Help, please. Thank you

  A few times, you can get unexpected behavior on the device. To trick you can use.

• net_rim_app_manager. Debug and other debug files

  Hello

  where can I download:

  • net_rim_app_manager. Debug
  • .Debug net_rim_cldc (*)
  • net_rim_bb_medialoader_backgrounds_480x360_b .debug (*)
  • net_rim_bb_medialoader_ringtones_89xx .debug (*)
  • and all the others-debug files

  for my BlackBerry Curve 8900 with OS 5.0.0.1067 debug 1.3 (on Eclipse 3.6.1 download of RIM) with BlackBerry Java plug-in for Eclipse?

  If I ignore these debug files ("don't ask again"), will be able to debug my device?

  And so, I can't find any Simulator for OS 5.0.0.1067...

  Thank you

  Sincere greetings,

  franc

  Yes, there is no download I know.

  No not you have debug, in any case.

  usually, you want to debug your application and maybe a related library, you need the files of debugging for them.

• No.. Debug and not able to deploy BlackBerry double initialize?

  It's freaking me out and is very definitely a rookie mistake so sorry in advance.

  Why is that if I do this in a class

  Private double d1 = 0;

  the JDE and Eclipse will not generate a .debug file and let me debug BUT

  If I do this

  Private double d1;

  It works fine? The error I get is "debug information are missing. Not all applications can be debogables... "blaa blaa.

  Again, I am new to Java to take it easy on me...

  In case someone else runs into this, it was a rookie mistake.

  I was running the jde 5.0 but my phone worked only 4. something OS. He didn't like it.

  Ken

• The ACS 5.3 device name time and telnet

  Dear all,

  This is the place to discuss GBA, I need two entries more experts

  ACSServer

  Thu Sep 13 14:35:28 UTC 2012

  pughaz

  15

  [CmdAV = Ganymede ip source-interface FastEthernet 0/1]

  Device Type: all device Types: ROUTERS, location: all locations: MATERIAL DC NOT

  On the above message

  1 need to chang time UTC at IST

  2. the device column does not appear the exact device name; I have telnet and config changed, is to show the name of the single unit group, how to get the exact device I appoint telnet on this message

  Hello

  You can change the zone through the cli:

  For the exact syntax of zone-

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.3/command/reference/cli_app_a.html#wp1892764

  Here is the command to do this-

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.3/command/reference/cli_app_a.html#wp1894584

  As far as the name of the device does not, you can check the column settings and see if it can removed.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• PIX 515E and Telnet to port 25

  When I telnet (in or out) on a mail server (using port 25) the answer is:

  220-*******************

  and all orders come back as "invalid command."

  When I put the old (no - pix) firewall, this does not happen (the responses are complete and commands work fine.)

  A lot of email is coming and going, but some mail servers cannot send email.

  This is common for misconfiguration and where should I look?

  Thank you

  Mark

  Delete the fixup protocol smtp 25!

  command to run:

  No fixup not protocol smtp

  Details about this:

  The order fixup protocol smtp active the function of guard of mail, which allows only mail servers receive the RFC 821, section 4.5.1 of the orders of HELO, MAIL, RCPT, DATA, RSET, NOOP, and QUIT. All other commands are translated into x which are refused by the internal server. The result is a message such as "500 unknown command: 'XXX'.» Incomplete orders are ignored.

  Note during a SMTP session interactive, different SMTP security rules may reject or hang with your Telnet session. These rules include the following: SMTP commands must be at least four characters; must end with the return cart and jump; of line and must wait for a response before issuing the next reply.

  From PIX Firewall software Version 5.1 and higher, the fixup protocol smtp command changes the characters of the SMTP banner asterisks except for the "2", "0", "0" characters. Return (CR) and linefeed (LF) characters are ignored.

  PIX Firewall software Version 4.4, all the characters in the SMTP banner are converted to asterisks.

  Reference:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_command_reference_chapter09186a00801727a8.html#wp1067379

  sincerely

  Patrick

• Debugging and testing custom taskflow-ADF

  Hello

  I have a custom ADF taskflow that is deployed and used in WebCenter spaces, trying to understand the process of development and debugging. How can I debug this ADF taskflow outside WebCenter, i.e. in JDeveloper spaces? Can they just be running on the server Weblogic integrated or what I need to find a way to set up debugging on the server, WebCenter?

  Thank you

  Hello.

  The white paper is nice enough explaining the new way on the deployment of the task flows into the portal and to persist on questions of web.xml.

  From my experience, if the task runs are fully developed without any dependency (spaces) Portal (like spaces API or EL Expressions) they can be perfectly run locally and tested before deploying to the portal (spaces).

  However, sometimes the task developed flow are dependent on runs inside the portal (application for spaces). From my experience, I always try to have my developers working with a Virtual Machine with an installation of site in order to get the speed in testing and deployment of task flows to the portal (spaces).

  Summarize:

  • Portal (spaces): Local Virtual Machine.
  • : Portal Install ADF frame JDev WebLogic integrated in order to have the opportunity to consume MDS development database. It allows all developers work in their integrated WebLogic sharing MDS and Services installed in a Dev environment.

  I hope it helps.

  Kind regards.

• Developer SQL Debugging and Securiy issue

  Running PL/SQL: CALL the DBMS_DEBUG_JDWP. CONNECT_TCP ('my pc ip', '58201')

  ORA-30683: failure connecting to debugger

  ORA-12535: TNS:operation expired

  This message appears when I try to debug a procedure of the SQL Developer. I have concluded that the database cannot connect to the debugger on my pc for to proceed with debugging. I have security problems in our network for open access on the database side to my pc.

  Oracle has put this question in concern the preparation of the debugger? Is there a way to set the debugging procedures and functions to be server-side? or suggestions to work around the security concerns.

  N.B.:

  1. Toad both server-side options, and client-side debugging
  2. There are a lot of request for access will be issued to allow the databases to connect to client computers and it is an application of type of unreasonable for people to safety.

  SOLVED

  I opened my pc access over the network to the database, so now the database can connect to my sql developer debugger when you are debugging.

  Thanks for the support

• SE bin-debug and bin-release to work

  Hello

  I'm really stuck.

  I have my application to work with a MySQL database (the application itself makes no difference)

  When I compile and run the application with the menu ¨Run! and then ¨run main¨, everything works fine.

  But when I go in the bin-debug or release-bin directory and ask the application.html to open in the browser, I just get my repeating error

  Someone told me that the gataway.php file should not be referenced as url: but I don't know what that means.

  It certainly has to do with the dataservice access, but my Spanish is at the end on debugging. Who can unlock me really (I'm stuck for a good week on that.

  At the end I want to do is to export bin-publishing to a remote server (not localhost) in order to make the application available on the internet.

  I thought I can just ftp release bin in this remote server and perhaps adjust the MySQL database access settings.

  But I also need something to the Zend Framework, I guess.

  Help, please

  Peter

  its because when you hit in FB runs the application in a local server

  If you open the file in Windows Explorer, you won't be running on the local server.

  using WAMP? You have an icon in the system tray? Click on that and open localhost, find the Debugging folder and execute the html page from there. It will work because you are in the local server environment

  This might help

  http://www.YouTube.com/watch?v=P333JuiX-V8

• Debug and parameter groups to release

  Hello

  I created a plugin and I am faced with two questions right now. First of all, my user interface is a little cluttered. I've read all the SDK but could not find enough information on how to create groups of parameters.  Second, can someone tell me how to convert the plugin from Debug to release in Xcode and Windows? Also, whenever I change the Outflags, AE throws an error saying that theere is an incompatibility with PiPL. How is this figure PiPL calculated? Is this just a hexadecimal number?

  Thank you much in advance.

  Once, there was a call API ADM (the adobe dialog manager).

  It enabled plugin programmers to create windows with various controls, including text boxes.

  I don't know why, but it is no longer supported.

  Anyway,.

  Since you mentioned using interface builder, I guess that we are talking about mac.

  I have to tell you my friend, you have hit the spot with this question.

  There are a lot of little problems in this process, which left me frustrated for days on end.

  so now you have a .nib file and ask yourself, "now what?"

  first of all, open the .nib file in interface builder.

  set the modal class of the window 'furniture '.

  This will ensure the window being in front of the AE and avoid interactions with EI until the window is released.

  the second step would be to add the .nib file to the xcode project.

  of course, you add the file like any other file, and it appears in the project.

  You should see that it also appears on the last record on the project, called "Files" NIB.

  We're not done Add.

  now spin towards the bottom of the category "targets" and twirl down the name of your plugin.

  You can now see the stages of construction.

  Now add a new generation of scene, "copy bundle resources" and add the file in as .nib.

  now, compile your plugin and go into the generated file.

  Open the packaging and check that the file nib is there.

  included with success?

  We are still adding stuff.

  now add two objects of type "existing frameworks.

  'IOKit.framework' and 'CoreFoundation.framework '.

  We move.

  go to the folder 'mac' inside the project folder and look for a file named "YourPlugName.plugin - info.plist".

  open it with the property list editor.

  We are especially interested in the chain of CFBundleIdentifier.

  This is very probably "com.adobe.AfterEffects.YourPlugName."

  You can keep it like that, or change it to anything you want.

  Make sure it is unique, so no other packs in the world would use the same name.

  Copy this name. We need to later.

  and that is how it is all being implemented:

  some of the statements

  CFBundleRef bundleRef = NULL;

  IBNibRef theNibRef = NULL;

  OSStatus theErr = NULL;

  const EventTypeSpec [] = {{kEventClassCommand, kEventCommandProcess}} kEvents;

  WindowRef ActivationWindow = NULL;

  Create a reference of nib

  bundleRef = CFBundleGetBundleWithIdentifier (CFSTR ("replace this text with the name of bundle of earlier"));

  theErr = CreateNibReferenceWithCFBundle (bundleRef, CFSTR ("replace this text with the .nib, without the .nib extension file name"), & theNibRef);

  optioanl control to find errors.

  You should put this after almost every step.

  It is up to you.

  require_noerr (theErr, CantGetNibRef);

  Create a window.

  It is still not visible at this point.

  theErr = CreateWindowFromNib (theNibRef, CFSTR ('Window'), & ActivationWindow);

  We don't need the reference of the pen more.

  DisposeNibReference (theNibRef);

  ensuring that the window appear somewhere on the screen.

  RepositionWindow (ActivationWindow, NULL, kWindowCascadeOnMainScreen);

  The window has been created hidden then show it.

  ShowWindow (ActivationWindow);

  Install event handlers

  theErr = InstallWindowEventHandler (ActivationWindow, EventHandlerFunction,

  GetEventTypeCount (kEvents), kEvents, (void *), ActivationWindow, NULL);

  Call the event loop

  RunApplicationEventLoop();

  This is it. you are now stuck at the event loop until end you it.
  Here is the Basic code for the event handling:
  #define OkCommand 'ok '.

  #define CancelCommand "no!"

  OSStatus ActivationFormEventHandler)

  EventHandlerCallRef inHandlerCallRef,

  EventRef inEvent,

  void * inData)

  {

  OSStatus theErr = eventNotHandledErr;

  HICommand theHICommand;

  WindowRef theWindow = inData (WindowRef);

  () GetEventParameter

  inEvent, kEventParamDirectObject, typeHICommand, NULL,

  sizeof (HICommand), NULL, & theHICommand);

  Switch (theHICommand.commandID)

  {

  case OkCommand:

  do what you want to do when the user clicks on "ok".

  termination of the window and freeing up the process of return to the effect.

  DisposeWindow (theWindow);

  QuitApplicationEventLoop();

  break;

  case No. CancelCommand:

  and the same for when the user clicks "Cancel".

  QuitApplicationEventLoop();

  theErr = noErr;

  break;

  }

  Return theErr;

  }
  That's all.
  This should help you operational.
  :-)