debugging packages with ASA 7.2 worm (2)
Hello
Previously with the version 6.3 of the PIX you can debug the packets in real time. That is to say with the command of debug package.
Looking through the ASA 7.2 (2) order that the command of debug package no longer exists. If the order of packet - trace exists, is not in real time.
Does anyone know how you debug packages with version 7.2 (2).
Thank you
Brett
Create an ACL identify traffic that you want to debug. Create a capture specifying the ACL and the interface enters the circulation.
Example:
capture from the list of allowed access host ip x.x.x.x y.y.y.y
capture mycapture access interface to capture inside list
See capture mycapture detail dump
Tags: Cisco Security
Similar Questions
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Installation of Service Pack 3 cannot update an active (debug) system with a free(commercial) version of Service Pack 3, or vice versa.I tried the regedit fix. Setting HKEY_LOCAL_MACHINE\Software\Microsoft\Windows NT\CurrentVersion current either free, or verifiedThis has not worked for me. I don't seem to be able to find another fix.I also have a pop - up every 5 minutes on my computer after you perform a repair with the xp disc. It reads as follows (Microsoft Feeds Synchronization has encountered a problem and needs to close.AppName: msfeedssync.exe AppVer: 8.0.6001.18702 ModName: user32.dllModVer: 5.1.2600.2622 Offset: 000095d 8Thanks for any help.
Hello
1. How do you try to install Windows XP service pack 3?
2 did you change on your computer before this problem?
You can follow the suggestions and check out them.
Method 1
You can follow the procedure in the article.
How to troubleshoot an installation fails on Windows XP Service Pack 3
http://support.Microsoft.com/kb/950718
Note: Antivirus can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.
Method 2
You can reset the grocery store.
a. click on start, then run.
b. type %userprofile%\Local Settings\Application Windows and press OK.
c. remove all files in the folder.
Note: You can export the workflow before you restore it and import it on the computer.
See also:
Steps to take before you install Windows XP Service Pack 3
http://support.Microsoft.com/kb/950717
Note: Antivirus can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attack.
Learn how to install Windows XP Service Pack 3 (SP3)
http://Windows.Microsoft.com/en-us/Windows/help/learn-how-to-install-Windows-XP-Service-Pack-3-SP3
-
Service Pack 3 Setup error: "Service Pack 3 Setup cannot update an active (debug) system with a free (retail) version of Service Pack 3, or vice versa"
I have XP SP3 download Tuff. I have a Dell Inspiron 16000 w / XP Edition home (version 2002) W / SP 2 is installed. I couldn't find a reference to the error in line last night. Can anyone help?
Turbo Tax 2011 says that I can not download their stuff until I get my XP Stuff to the height.
Only 6 more days until what the tax man will come :-)...
Help!
Put your search inside the quotes term allows when you search for the exact error messages:
"Service Pack 3 installation cannot update an active (debug) system with a free (retail)"
The first shot has the answer: http://www.askvg.com/windows-xp-sp3-setup-error-cannot-update-a-checked-debug-system-with-a-free-retail-version-of-service-pack-3/
CurrentType at HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion value should read "Uniprocessor Free" or "free multiprocessor".
John
-
NAC Appliance with ASA (for remote user VPN)
I have a pair of firewall 5520 cisco which is used as a VPN gateway (for remote user VPN) and perimeter firewall Internet (to provide outbound internet connectivity).
We allow the NAC to remote VPN users. I have it will be deployed with active 3 layer inband.
The problem with this design is that how to ensure that outgoing internet traffic does not pass through the CASE?
I heard about couple of optioins:
-ACB (for send only IP subnet to VPN users remote to go through CASE)
-Version 8.x characteristic of ASA (Restrcit access to VLAN under Group Policy).
I intend to do with ASA firewall where I can set a new subinterface on the SAA (with a new tag VLAN) and under the group policy for remote user VPN, I select the option to "restrict access to the new VLAN.
My question is: is - it still works (even if the firewall have a route to the internal network by using the 'inside' interface and NOT the new interface of the NAC). If this does not work, please let me know what are the other options for this type of deployment.
Thanks in advance.
Hello
It should work. Please see the attached PDF for more clarity on this topic: https://supportforums.cisco.com/docs/DOC-9102
HTH,
Faisal
-
No Internet connectivity with ASA 5505 VPN remote access
Hello
I configured ASA 5505 for remote access VPN to allow a remote user to connect to the Remote LAN officce. VPN works well, users can access Office Resource of LAN with sahred etc., but once they have connected to the VPN, they are unable to browse the internet?
Internet navigation stop working as soon as their customer VPN connect with ASA 5505 t, once they are disconnected from VPN, once again they can browse the internet.
Not ASA 5505 blocking browsing the internet for users of VPN? Is there anything else that I need congfure to ensure that VPN users can browse the internet?
I have to configure Split Tunnleing, NATing or routing for VPN users? or something else.
Thank you very much for you help.
Concerning
Salman
Salman
What you run into is a default behavior of the ASA in which she will not route traffic back on the same interface on which he arrived. So if the VPN traffic arrived on the external interface the ASA does not want to send back on the external interface for Internet access.
You have at least 2 options:
-You can configure split tunneling, as you mention, and this would surf the Internet to continue during the use of VPN.
-You can set an option on the ASA to allow traffic back on the same interface (this is sometimes called crossed). Use the command
permit same-security-traffic intra-interface
HTH
Rick
-
Changing table via the package with immediate execution (problem)
Hello
I have a unusual problem. I have a package that contains the procedure that via execute immediate statement, creates a table on which he performs different actions for example:
-alter table some_owner.dummy_table noparallel
-create index some_owner.idx_name on some_owner.dummy_table (column)...
But I only managed to run move and create synonym table/public via execute immediate statement. Actions as alter table and create index fails with error ORA-01031: insufficient privileges.
Note If call these commands outside the package (a simple script) this all done OK.
I found a way, where I set the AUTHID CURRENT_USER command create package statement. In this way all the actions executed OK.
I wonder why I can't change the table via the package with immediate execution on a table that is in the tablespace "SOME_TABLESPACE" and the title of owner "SOME_OWNER", without putting the AUTHID command on the package.
There must be a problem why a package cannot change the table which is owned by the user 'SOME_OWNER '.
All useful responses would be appreciated.
I have a unusual problem.
No - you don't have. This question has been answered SEVERAL times on this forum and others.
But I only managed to run move and create synonym table/public via execute immediate statement. Actions as alter table and create index fails with error ORA-01031: insufficient privileges.
OK - your username doesn't have privileges to do these operations or only received privileges through roles.
Roles are DISABLED in named PL/SQL blocks that use of the AUTHOR's rights.
Note If call these commands outside the package (a simple script) this all done OK.
I found a way, where I set the AUTHID CURRENT_USER command create package statement. In this way all the actions executed OK.
Of course - the roles are NOT disabled in named PL/SQL blocks that use the rights of the APPELLANT or in anonymous blocks.
I wonder why I can't change the table via the package with immediate execution on a table that is in the tablespace "SOME_TABLESPACE" and the title of owner "SOME_OWNER", without putting the AUTHID command on the package.
Well now you know!
-
Instill items 11 (mac) with OSX El Capitan worm. 10.11.4 puts icon on the screen, but then nothing, any help please.
I thought I would try the version test, but with the same problem, will not work.
Any help please would be appreciated
Concerning
MP
How to open third-party applications to developers not identified in Mac OS X "Mac tips.
-
Hi all
AM creating packages with Creative could conditioner, need to include 'Extension Manager CS6 ' to my list of requests, I downloaded a version and trying to add to the list with the help of add the option offline media, but get the error as media is not appropriate etc...
Can any body please let me know how to add media offline while we creating packages with Creative Cloud Packager.
Thanks in advance.
This is possible in theory, as long as the source media that you add is complete and unzipped. Also if 32 bit it cannot be added to a 64-bit package and vice versa.
It's not really what this feature is designed for good. It is designed for DVD sets provided to customers who live in areas where poor internet infrastructure that cannot download apps via CCP.
-
I have been subscribed to a single package Photoshop CC from 2013, and one of my friends said that I was paying too much, and I should at least have included Lightroom. So, I checked, asked a few questions to the (probably a bot) chat service, before I knew he was there, my possibility to opt for a package with photoshop and Lightroom (including bridge)
It was time to update my existing bridge and photoshop. After doing this, all of a sudden my photoshop has changed in a 30-day trial! How can I fix it?FIXED! Re, I entered the cat, with the hope to fix with someone, and it is fixed!
-
I have PS 4, 5 and 6 is installed on my Macbook Pro and Lightroom 4 and 5. Can I remove PS 4 and 5 and 4 LR? PS 4 is the entire plant and PS 5 and 6 are updated. LR 4 is the complete package with LR upgrade.
I need space!
First of all, let me disabuse you of a misconception: Adobe all upgrades are FULL installers. If you buy upgrades or new versions does not have one iota of difference. Upgrade installation programs do not need to find a previous version installed, they invite you just for the old serial number as well as the old one and they are not based on the old version in the slightest.
Second, the time to uninstall an earlier version is BEFORE upgrading to a newer version. If not, uninstall older versions will mess up with your new installation. There are a gazillion of the files that are named the same and in the same locations as the other.
Your best bet now is to uninstall ALL versions of Photoshop, you have it installed, including the newest one, one by one, and then run the Adobe CS clean-up tool, and then run repair permissions of the Apple desktop utility and finally reinstall the latest version.
The other alternative, if your boot HD is quite large (very questionable in the case of a laptop as a Mac Book), is to leave all the versions on this subject.
Your choice.
-
demand has been to package with a runtime in captivity
Hi all
The system configuration:
Flash Pro CC
Use of AIR 13.0.0.95 for iOS
Use of AIR for Android 13.0.0.95
I could test my app (DeveloperProv and DeveloperCert) and send (DistributionProv and DistributionCert) to iTunes Connect Using Flash Pro CC successfully > AIR for iOS. My application is currently pending review. I'm fine with the part of the iOS.
Currently, I'm trying to publish my APK, I did and a get a window display "Adobe Flash Professional > APK was set successfully, but a warning." Note: the application has been the package with a captive runtime. »
The message is a little confusing, firstly the APK is successful, and then a warning occurs. Is that what I can do to get rid of this warning? Is how important it?
Thanks in advance for any further discussion.
Flash is just show something that this ADT reports. It is not a mistake, it's just an observation. You can't get rid of it, and no, it's not bad.
-
The charge would be created with the unique package with date id
Hi all
Thanks in advance,
IAM new to ODI, in my process I dnt know below two constaraints how to do, please help me in this regard...
1. the load would be created with the id of a single lot with the date and
stamp under the unique number (when the load data from source to target).
2. HIGHLAND field would have the line number incremented from
.001 when records are inserted in the table30021986 wrote:
HelloThanks for the reply, my requirement is,
1.i have field JELN in the target table, in that line number is incremented from de.001 in the table. (Field JELN would have the incremented number line from de.001 when the rows are inserted in the table)-> for what I had done using sequenceing odi_sequence craeating, but it will give higher error.
and the second condition isNever use ODI sequence unless you do business with a technology that has no native sequence is
(eg files). Most of the RDBMS has their own sequence, and you use these alone.
For oracle, you must use. NEXTVAL in the field mapping. Be sure to run on the target. 2. when iam loading the data from the source to target a unique batch number must be generated with the date and time stamp (the load would be created with the unique package with date id and + *)
timestamp in the unique number +) *.You can use SYSTIMESTAMP in this area and do not forget to run on the target.
-
Can Wireshack we package with ThinApp
Application that need to install the service and the other maybe special device driver package with ThinApp. The application in question is wireshack. I know this isn't the norm, but I think is the worst scenerio and be a good test to try. After that I installed and package wireshack with thinapp, I'm missing dll error service not started. Did the package on a windows XP VM guest where finishing package has been trying to start on a physical window vista.
DWC
No, applications that depend on the kernel mode device drivers cannot be packed.
-
Hello
I want to install 2 on real java card applets. They are in the same package and can use each other.
How can I do this on JCOP?
and what happens if they are on the packages of the difference and what happens if I use a few other lib as well? do I need to install this lib also if yes, how?
BR
UmerIf your packages and applets are in a single project Java Card JCOP, this must be processed for you. You can have several cmdlets in a package, you can have multiple instances of a simple applet, and you can have multiple packages with several cmdlets as well as library packages.
If you want to access an applet from another cmdlet in a single package, as a reference to another instance of the class. If they are in different packages, you use shared objects. It's because of the firewall of the applet.
See you soon
Shane
Maybe you are looking for
-
How to transfer from one computer to another search history
I want to reinstall my windows, so I have to save my search history and put it in mozilla firefox.
-
Hello I created a simple Subvi (attached), that I would use whenever I need activate or disable the States of a TAB control. However I can see there is a point of stress when I connect a reference to the refnum TABcontrol input terminal. I'm not fami
-
than 25 ns sets sampling rate...
Hello I'm trying to test the sampling rate of chassis cRIO 9103... I created a simple FPGA project, for sampling sign this clock frequency of the FPGA equal to 40 Mhz (on by default). I applied 1 Mhz square wave to pin MISO DIO6/SPI, place one of the
-
Hello I think this is the right place to post dump files memory to get the help of troubleshooting questions? I started on this: link to use Driver Verifier, and the latter built: link Learn how to find and download the files to get help. So this is
-
7 missing public windows desktop folder
My public desktop folder is missing. I can create an ok but when I restart again his party. How can I get there? Thank you Colin