DELL EMC CX600 FC SAN with ESX4.1 or ESX4 reference

Similar Questions

• Dell XPS 15 (L502x) problems with mSATA, it is even compatible?

  Hey all,.

  After you run out of warranty and immediately having HDD, I decided to install an mSATA SSD for faster boot times (with the possibility to keep a large spinning for storage disk). I bought a Liteon M3M 128 GB module and installed in the mini-pci-e slot in the compartment under the laptop.

  After that installation there no change, nothing picked up in the bios, nothing through a live Linux OS, nothing in the installer of windows and nothing in Windows itself (when I gave up and replaced the drive rotating and re-installed).

  I've updated to the latest version of the BIOS (A12) but this does not make any difference, I just googled and there is mention of a disabling Intel RST, but this option is not available for me in BIOS

  Is there something that I have done is wrong, it is likely that the device is defective, do I need some kind of pilots of special controller for installation of windows 7 or is this model of Dell just simply not compatible with mSTATA?

  See you soon,.

  -Dan

  Hi Dan,.

  XPS L502X supports the devices in the solid state (SSD) of 256 and 512 GB of capacity. However, I'm sorry to inform him that it does not support the mSATA disks. You can replace the hard drive with an SSD in order to improve the performance of the system.

  Please let me know if you need further information.

• Dell 8IO printer is compatible with Windows 7?

  Printer problems

  Dell 8IO printer is compatible with Windows 7?

  According to Dell, it is.

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/DriverFileFormats?c=us&s=BSD&CS=04&l=en&DriverID=R146120

  SC Tom

• Reference Dell photo printer 720 compatibility with Windows 8

  Is Dell photo printer 720 compatibility with Windows 8. ?

  You would be better to replace this printer.  It was a free add to dell computers sold in 2004 that cost $25 buy then. It's time to buy a new one.

  It is not compatible with windows 8 - see THIS

• Boot from SAN with 4 HBAs

  Hello

  What are the guildlines for boot from SAN with 4 fibre HBA.
  Our HP Blades originally had 2 available Qlogic host bus adapters.  I have always chosen a boot on both device and the servers never had a problem starting.  Recently we add a second back-end connectivity map and associates of mezzanine on the HP to allow everything.  On the SAN and blade we show 4 HBAs.  Now when booting of servers, we have stuck in the bootloader GRUB.  This has happened on a server that has already been built and when we reinstalled.  What are the guidelines for booting from the San with multiple HBAs.  We use ESX 4.1.

  Hello

  The general rule is that boot from SAN works on HBA cards in the lowest PCI slot.

  I don't know what rules HP uses to translate slots PCI mezzanine cards.

• Problems with 5.4 Mirage download reference CVD

  Hello

  I tried to go down my 5.4 Mirage ground infrastructure, but I continue to turn in questions with the CVD reference do not download.

  I have two Mirage servers behind a Barracuda Load Balancer, and even if I point the Mirage customer directly to one of the nodes in an attempt to capture the reference machines I get the same error below.

  Any help is appreciated.

  Full download failure

  Device ID is 3 ', CVD ID is 10003'

  System.NullReferenceException: Object Reference not set to an instance of an object.

  to Wanova.Server.Common.Database.CommonStorageOperations.GetPrimaryMongoVolume (ISession session)

  to b__0 (ISession s) Wanova.Server.Common.FileSystem.OperationsWrapper.Sis2FileSystemErrorWrapper. < FindCurrentProblematicVolume >

  to Wanova.Server.Common.Database.Storage.RunDbOperationInternal [T] (try Func 2 dbOperation, IsolationLevel isolationLevel, Int32, Int32 batchSize, IStorageRetryChecker retryChecker, String funcName)

  to Wanova.Server.Common.Database.Storage.RunDbOperation [T] (try Func 2 dbOperation, IsolationLevel isolationLevel, Int32, Int32 batchSize, IStorageRetryChecker retryChecker, String funcName)

  to Wanova.Server.Common.Database.Storage.RunQuery [T] (Func 2 doQuery)

  at Wanova.Server.Common.FileSystem.OperationsWrapper.Sis2FileSystemErrorWrapper.FindCurrentProblematicVolume)

  to Wanova.Server.Common.FileSystem.OperationsWrapper.Sis2FileSystemErrorWrapper.Wrap [T] (Func 1 action)

  to Wanova.Server.Common.FileSystem.ErrorHandlingRemoteSis2FileSystem.BatchExists (IList 1 fileProperties)

  to b__0 Wanova.Server.Common.FileSystem.BatchingUnit.HoardingFileSystem. < BatchExists > (IEnumerable 1 inList)

  to Wanova.Server.Common.FileSystem.BatchingUnit.HoardingFileSystem.ChunkIntoBatches [TIn, everything] (IEnumerable 1 fileProperties, Func 2 application)

  to Wanova.Server.Common.FileSystem.BatchingUnit.HoardingFileSystem.BatchExists (IList 1 fileProperties)

  at Wanova.Server.Common.FileSystem.BatchingUnit.ManifestBasedCachingFileSystem.ProcessManifest (IStreamingManifest manifesto)

  at Wanova.Server.Server.Upload.PrepareUploadCompletion.CreateSis2DedupIndex (IDedupIndex, dedupIndex, clear IStreamingManifest)

  to Wanova.Server.Server.Upload.PrepareUploadCompletion.OnCompleteWithSuccess (IFileSystem tempAreaFs, onSuccess, Action 1 onError Action)

  I was using a Dell FS8600 NAS back ends with Compellent SAN.

  The problem was the storage subsystem.  Confirmed by the creation of a file out on the network server and use it as my first volume.  Operations have succeeded at this time.

  Will have to study with Dell to find out why their device does not work with the Mirage.

  Fluid FS version 3

• SRM with different DELL/EMC CLARiiON systems

  I have a client who currently owns a Dell Clariion CX300. They seek to replace it with a CX4-120 and would send the CX300 to an offsite location for use as a solution using MRS. DR.

  According to my research, I believe that this solution is possible using EMC RecoverPoint/SE to mirror, both on an IP network, but what is not clear is if I need is more SnapView and MirrorView (I don't think I do)

  HA - that someone does something similar to this before and care to share their experiences?

  Hi Sean

  I am writing as an employee of EMC society UK VMware affinity team. Please see my responses below online

  "I have a customer who currently has a Dell Clariion CX300. They seek to replace it with a CX4-120 and I would send the CX300 to an offsite location for use as a solution using MRS DR. »

  > > > > It is possible - if as you suggest with the CX300 not support MirrorView based SRM (support for this begins with the CX3 family) the only way to achieve consistent SRM and SRM with the CX300 is through the use of RecoverPoint as you suggest

  According to my research, I believe that this solution is possible using EMC RecoverPoint/SE to mirror, both on an IP network, but what is not clear is if I need is more SnapView and MirrorView (I don't think I do)

  > > > > RecoverPoint uses its own capabilities in conjunction with a host, fabric based or CLARiiON based write splitter log all entries available to a designated SAN "volume of the journal. SnapView or MirrorView are required for this

  > > > > the CX3 / generation CLARiiON CX4 supports the separator RecoverPoint CLARiiON that allows these units to split the writings of two VMS with RDM (which is a limitation when using the separator with ESX host - the host splitter only supports Microsoft VMs using RDM - so no support of the SRM) while being able to split the Scriptures volumes VMFS suitable for SRM.

  > > > > fabric database splitting and splitting based CLARiiON are fully integrated with ESX, including support for Site Recovery Manager (in accordance with the comparability of VMware SRM Matrix) as the CX300 supports not the CLARiiON splitter - this gives you the choice of fabric-based splitting of the side DR using something like the Brocade 7600 or the switch Cisco SSM blade or 9222i Fabric my concern with what is the cost of implementation of a fabric RecoverPoint intelligent solution based on the side DR may exceed what the client will budget for his site of DR

  > > > > According to the profile of the ESX data replicated to the site of DR it can be cost-effective to improve unity DR to another CX4-120 and use MirrorView together with SRM or if RecoverPoint remains the preferred - solution have CLARiiON both production and DR site able to support the CLARiiON RecoverPoint splitter

  Let me know your thoughts

  Kind regards

  Alex Tanner

• Creation of VM in local ESXi datastore for the backup of the data SAN with VMXNet 3 VM store

  Hi all

  I would like to know how you have configured your server to backup as a virtual machine?

  My idea is to use the local data VMFS3 store on my 3 x ESXi servers,

  by installing the application of part 3 (such as Veeam Backup 5 or Backup Exec 2010) in Windows Server 2008 R2 VM

  equipped with size of very big hard drive (OS 8 GB + 1 TB VMDK data partition) on each of the local data store to save the computer virtual within the SAN.

  What I have:

  VMware vSphere essential 4 - ESXi 4.0 (not hot add)

  Dell Power Edge 2950 with 2.5 to multiple VMFS3 extended on top - RAID 5 (6 x 500 GB SATAII 7200 RPM)

  Reference Dell MD3000i iSCSI SAN on Gigabit Ethernet

  The configuration of the Windows Server 2008 R2 VM:

  2 x CPU @ 2.33 GHz

  4 GB OF RAM

  VMXNet3 NIC-> for better connectivity to the backup between the local data store ESXi and iSCSI-SAN data store.

  Here's the reason why I'm doing this is that:

  1. I don't have the additional NETWORK card to connect my physical server in iSCSI SAN THAT switch, so I can't use - SAN backup mode.

  2. I only use the available lowest VMware license that can't stand the Hot-add the device function.

  Would it be an optimal configuration?

  Any kind of help and suggestion to implement backup VM VM would be greatly appreciated.

  Thank you.

  Kind regards

  AWT

  From what I see of you think to do, you will get no advantage of using the VMXNET3 NIC, compared using an e1000 NIC... All your traffic will be on the connections of 1 GB, because you're leaving SAN local disk... If you had the VM on the SAN, or the same storage, the VMXNET3 NIC were going at speeds of internal circulation (could get you better than 1 GB, but I advise to test before committing)...

  In addition, you will not be able to use a volume of OS 8 GB in Server 2008 R2... Bare minium is 32 GB (use plus 40 GB, which is that vSphere will use when you tell him to 2008 R2 for the operating system of the virtual machine)...

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• Reference Dell 410 repaired but loaded with a fake Windows XP Professional

  After having my Dell 410 repaired, I discovered it had been loaded with a Windows XP Prof. from the false, I can't contact people who repaired (surprise) what can I do? I have my original key code but not xp disc

  Hi Trevor,

  I'm sorry to hear that you have been scammed with a fake copy of Windows XP. I suggest you to contact Microsoft customer service and check.

  Hope this information is useful.

• How many times can I use the Dell restore cd that came with my system?

  I ran the cd of restoration over 3 times and nothing has changed that I have I'm restoring an old dell dimension xp. I thought that this would erase it clean and set of parameters by default now I can't boot the OS and not much has changed. I get a blue screen with an error message window was closed to protect the computer and search for viruis.  I found my way in the tree view of the symptoms and I've been running tests, I don't know if this will help, and I still really need help because I am very new to the use of this forum, and now I'm tender hand on this Mac laptop. Boy, any help would be greatly appreciated this whole thing with computers, it's a change of lifestyle.

  A Dell Dimension 4700 Series are of desktop computers; and, as such, do not come with wireless capabilities.

  Connect with an Ethernet cable to your router.

  If you want to use a wireless connection with it, you must either purchase a Wireless USB adapter or a card PCI of Wirelesss.

  Here is an example of both:

  USB adapter: http://www.dlink.com/products/?pid=722

  PCI Wireless Card: http://www.ebay.com/sch/i.html?_nkw=wireless+PCI+card

  And here's all the information from Dell on Dell Dimension 4700 series.

  http://support.Dell.com/support/eDOCS/systems/dim4700/en/OM/Y69490LRs.PDF

  And it can help, too (Service Manual):

  http://support.Dell.com/support/eDOCS/systems/dim4700/SM/index.htm

  See you soon.

  PS You are welcome, the ROCKS of XP

• Reference Dell Touchpad is in conflict with Logitech mouse

  Original title: Dell 1735 Vista laptop touch PROBLEMS__ pad

  Despite my having DELETED the software that makes the touch pad on my laptop work so-called, it continues to 'work' and interfere with my Logitech wireless mouse, constantly move the cursor of the hit at a time that's not going!
  Can anyone help?  I don't ever want to use the Tablet!

  Despite my having DELETED the software that makes the touch pad on my laptop work so-called, it continues to 'work' and interfere with my Logitech wireless mouse, constantly move the cursor of the hit at a time that's not going!
  Can anyone help?  I don't ever want to use the Tablet!

  Hey kdjanet

  You can ask in the forums of dell support about this problem on your dell computer

  http://en.community.Dell.com/support-forums/default.aspx

  Walter, the time zone traveller

• How can I get a Dell A920 printer become compatible with Windows Vista?

  I have programmed a Dell A920 to print from my laptop Windows Vista printer.  It worked, but when I try to print something I get an error message indicating that the printer is not compatible with Windows Vista.  How can I get compatible?

  Hello

  Download and install the latest Dell Vista drivers;

  http://www.Dell.com/support/drivers/us/en/19/product/Dell-920

  See you soon.

• Can I install XP on my laptop dell inspiron 1501 though came with Vista Home Basic?

  I have a computer laptop inspiron 1501 and it came with Vista Home Basic.  I like better XP and wondering if I have an installation on my computer, I have an XP installation disc.  If I can, how to do it all?

  Hello

  You will be able to install Windows Xp on your computer, but you will need to perform a clean installation.

  Before installing Windows XP. And also, you will have to take up the data in your computer, because the new facility will remove all data into the computer.

  Download the driver from the support of dell at the following link:

  http://support.Dell.com/support/downloads/DriversList.aspx?c=us&CS=19&l=en&s=DHS&OS=WW1&OSL=en&CATID=&impid=&SystemID=INS_PNT_1501

  I would also like to inform you that there is now the operating system disks or support is available for Windows XP.

  For reference, see the following Microsoft.

  How to back up or transfer your data on a Windows computer:

  http://support.Microsoft.com/kb/971759

  How to install Windows XP: http://support.microsoft.com/kb/978307

  Hope the information is useful.

• I need to install Dell 968 to a computer with Windows Vista. Need instructions on how to do it.

  I need to reinstall a Dell 968 printer/scanner to a computer with Windows Vista. I can't find my instruction manual. Can someone tell me what to do? Printer works but when I scan something, the information does not go to the computer so that I can work with it.

  Hello

  Here are the drivers for your printer

  http://support.Dell.com/support/downloads/DriversList.aspx?c=US&l=en&s=GEN&ServiceTag=&SystemID=PRN_ALL_A968&OS=WNT5&OSL=en&CATID=&impid=

  and here's where to download this manual for her of

  http://support.Dell.com/support/topics/global.aspx/support/my_systems_info/manuals?c=us&l=en&s=Gen& ~ CK = anavml

• Upgrade a Dell Inspiron 531 to something with more memory and faster?

  Hello, I have a Dell Inspiron 531, 32-bit operating system, and the 3G memory in it but is Vista. I tried to upgrade to Windows 7, but after many attempts, could not go without having to clear everything and start over. So I'd do it if I have to do I was wondering if I could make the machine that is more memory better and faster, without having to buy a new computer say a Dell XPS 8300 (that I'll have to run a lot of photographic software in the future and I understand that this could be a good computer for that?) In any case, it is possible to 'upgrade' the computer something like this please, or I have to save my pennies for a new? Thank in advance for your advice.)

  Hello

  If you upgraded to 4GBs off RAM you won't get many benefits

  Here is an article on what is happening with 4GBs of RAM:

  http://support.Microsoft.com/kb/929605

  "If a computer has many features implemented, the available memory can be reduced to 3 GB or less." However, the maximum memory available in 32-bit versions of Windows Vista is typically 3.12 GB. »

  and you should also consult the Dell manual for your model desktop computer see what amount of RAM your motherboard would answer anyway

  http://support.Dell.com/support/topics/global.aspx/support/my_systems_info/manuals?c=us&l=en&s=Gen& ~ CK = anavml

  and here is the reason why you can not upgrade to Windows 7

  There are no Windows 7 drivers written for her by Dell

  http://support.Dell.com/support/downloads/DriversList.aspx?c=US&l=en&s=GEN&ServiceTag=&SystemID=INSP_DSKTP_D531&OS=WLH&OSL=en&CATID=&impid=

  Click on the menu at the link above drop-down operating system

  itonlt has XP and Vista drivers available