Dell TL4000 Tape Library on Cisco UCS 6120

Similar Questions

• Connection Cisco UCS 6120 FI directly to Cisco Catalyst 6500?

  I watch a lot of design with the Cisco UCS solution guide and everywhere it is Cisco Nexus 5000/7000 connects to the uplink ports of Cisco UCS 6120 FI with the benefits of technology to the vPC.

  How about connect Cisco UCS 6120 FI directly to 10GE ports in Cisco Catalyst 6500 (without VSS and VSS)? It is possible to design?

  If I use C6500VSS there will be port-channel of the aggregation of the UCS Nx10GE all the bandwidth?

  And what happens if I use C6500 (without VSS) - how it will be on the many links between UCS and two boxes C6500? It will be blocked by STP? A little on the other?

  Please explain to me, because we have only C6500 switches in our data center and want to test a Cisco UCS schassis.

  Yes, you can connect the 6120 s to cat6500s with or without vs. With VSS, you get a vPC as port channel where 2 links to a single 6120 can be connected to different 2 6500 s in a port LACP-channel.

  VSS is not necessary, you can connect a 10 G uplinks / 1 G of 1 or more of a 6120 at cat6500s. I you have 2 cat6500s (non - vss) and 2 uplinks by 6120, then you want to connect 1 cat6500-1 and the other to cat6500-2. I would recommend going ahead and creating a single port-channel port so that you can easily add the uplinks in the furture without interruption of service.

  Ideally, for non - vss, I would have 4 10 uplinks by 6120; 2 in a channel port cat6500-1 and 2 in a port in cat6500-2 channel

• Cisco UCS model to match Dell R900

  I am trying to replace existing Dell R900 (1 TB of disk space, RAM 24GO and 2 Quad core CPU) with Cisco UCS but don't know which model I should go with.  any response will be appreciated!

  It seems that the Dell R900 is a server in a rack, so if you are looking for something similar, you can try the C460-M4:

  Features at a glance

  • Four chassis rack unit (4RU)
  • 2 or 4 processor Intel® Xeon® E7-4800 v2 or product E7-8800 family processors v2
  • Up to 6 terabytes (to)^* memory (DDR3) 3 double-flow in 96 locations of memory online double (DIMM)
  • Up to 12 small Form Factor (SFF) hot-pluggable SAS/SATA/SSD drives readers
  • 10 slots PCI Express (PCIe) Gen 3 supporting the Interface Cards virtual Cisco UCS and the third-party adapters and GPU
  • Two ports Gigabit Ethernet LAN on motherboard (LOM)
  • Two 10 Gigabit Ethernet ports
  • A dedicated to out-of-band (OOB) management port

  ^* With 96 x 64 GB DIMMS when available.

  http://www.Cisco.com/c/en/us/products/servers-unified-computing/UCS-C460...

  I hope this helps.

  Let me know if you have any questions, if no, please check the question as answered.

  -Kenny

• Driver for IBM TS3100 Tape library. for windows 2008R2 and DPM 2010

  I installed DPM 2010 in the edition of Windows 2008R2 STD. I am using the IBMTS3100 tape library. Windows detects the tape device but media changer appears as unknown medium changer. I cannot see the details of the driver for the medium changer and means 'no driver file is required or have been loaded for the device. When I try to update the driver, it says already installed the latest driver for the device.

  Now the question is DPM does not detect the slots in the tape library.

  I have installed Symantec Backu Exec in the same server and everything works fine.

  If anyone has the driver for the device please inform else we are go to Backupexec... :(

  Hello

  The question you have posted is related to professional level support. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/category/DPM

• vFoglight with Cisco UCS

  Hello all,.
  We are looking for Cisco UCS for our ESX env. and I was wondering if someone was running vFoglight UCS and had problems.
  Or if someone of Quest/Vizioncore knows of any problem or future integration planned with UCS.

  Thank you
  Craig Dieck

  Craig, I know of many clients running the Cisco USC with VMware and they are very happy. There is no known issue with vFoglight perspective. VFoglight hardware monitoring currently able to extract any platform SNMP information. If you are looking for a vFoglgith to pull information from the physical ESX servers directly (not SNMP) you will need to ask for a discussion of the roadmap with your representative local of the quest.

  Inform the product manager for the platform you are using and what you want to be monitored and displayed...

• Cisco UCS B200 M4Compatible with 2100 FEX in UCS 5108 chassis & FI 6100?

  Hello

  The blade server Cisco UCS B200 M4 is compatible with FEX 2100 within a Cisco UCS 5108 chassis & Cisco UCS 6100 fabric of interconnection?

  The interop tool said clearly for the B200-M4:

  http://www.Cisco.com/Web/TechDoc/UCS/interoperability/matrix/matrix.html

  Note 14: The 2104XP fabric Extender is not compatible when the 1240 and 1280 or 1240 and VIC Port Expander are combined on the same blade. Applies to the M3 and M3 B200 as well as B420 B22 with 1240 and the 2 adapter connector populated

  or for the VIC 1340

  Note 38: 6100 series fabric interconnects and 2100 series fabric Extender is not supported

• UCS 6120 uplink and 1 Gbps

  Hello

  How can I pay my UCS 6120 Xp for 1 Gpbs speed as uplink to my switch to Upsteream I have only 1 G CLC MM wide

  MY UCS is 1.2 me I need to upgrade the software?

  could you help her

  Yes, you must be on 1.3 to support the option of 1 GB uplink. With firmware 1.3 8 first fixed ports are the only ones who take charge of 1 GB.

• Reserved Vlan ID in Cisco UCS

  I understand that to be true with Cisco UCS platform:

  "you cannot create a VLAN with ID from 3968 to 4047. This VLAN ID range is reserved. »

  I have a private network 172.16.x.x North on my network is in the vlan what ID 4001, I wanted to present this southbound on NGC.  Maybe it's a stupid question but the only way to be arounf to change the Vlan ID to the one who is sitting in the pool of UCS Vlan IDS that are allowed?

  Yes, unfortunately

• Cisco UCS C210 M2: PXE - E61: Media test failure, check cable of

  Hello

  I'm working on Cisco UCS C210 M2 servers. I got 10 146 GB SAS HD with LSI MegaRAID Raid Controller. I did run the Raid Controller and choose RAID6. After that I installed ESXi and it said to reboot the server. Now, when I restart the server I get the following error message:

  PXE - E61: Media test failure, check cable of

  PXE - M0F: Exit Boradcom PXE ROM

  Restart, and then select proper boot service

  or Insert Boot Media in some boot device and press a key

  Any suggestions how I can solve this problem.

  Thank you.

  You will need to go into the Bios of the controller LSI MegaRaid (Ctrl + H) and select the option of virtual drives on the left. When the virtual command window opens, you must select the drive (Raid Volume) on which you want your drive master boot and underneath there will be an option to set as your boot device. Apply and save.

• Nexus 5000 native FC disk array and tape library

  Is it possible to have servers to connect by FCoE to nexus 5000 switches as well as native berries FC of attached disk and tape library without requiring additional CF as the MDS 9000 switch? The reason why I ask, is that all the patterns I've seen on consolidated IO to this point show switches connected to the FC ports native on the nexus 5000 MDS. I thought that the Nexus 5000 would be able to replace the MDS attaching devices FCoE and native Fibre Channel devices. You see only such a diagram has me second guessing my initial thought.

  Yes, you can use FCoE and FC of Nexus 5000 to connect to networks. I tested and it works very well without any problems.

  FCoE, you have module FCoE in the bays and the appropriate license.

  RAM

• Cisco ucs with VMware 5 auto deploy

  Hello

  In our lab, I test with 5 VMware and Cisco UCS. We run UCSM 2.0 (1 m). I am now to test the auto hand deploy. I have auto configuration to deploy in VMware and it works (first of all, I had some problems with DHCP on windows which is solved in version 2.0 of UCSM (q)). vSphere gets deployed to the blade. When the blade (vShpere) wants to connect to vCenter I get an error of vCenter has enough licesing for this action. I loaded a lot of low-income VMware. When I create a virtual machine, it starts perfectly and apears in vCenter.

  I search on the internet for people who have the problem of the simailer, but could not find.

  Some body the same problem our help me?

  Thanks in advance,

  Robin

  Robin,

  This looks more like a VC related question (UCS) platform.  UCS has no effect on the functionality of licenses of the VC.

  If the host does not connect to the CR, how are you VMs to "start perfectly and appear in vCenter?

  Kind regards

  Robert

• vSphere 5.1 on Cisco UCS

  Hello

  I just want to check is one have tried to install VMware vSphere 5.1 on Cisco UCS blades? I was fine that some items and come to know that if you want to install vSphere 5.1, you have to first upgrade the firmware 2.0 (4A or 4B), and only then you can install / upgrade the 5.1 vSphere

  If anyone has a sine qua non for the installation of vSphere 5.1 on B200M2 & B200M3 to share the same

  -Amit

  Hello Amit,

  The UCS SW/HW interoperability tool should answer your questions.  5.1 ESXi is supported of the UCS 2.0 (4) and later versions.  Install the OS, and then update the drivers enic & fnic from the ISO driver available on cisco.com

  http://www.Cisco.com/Web/TechDoc/UCS/interoperability/matrix/matrix.html

  Matthew

• CISCO UCS C200 M2 amber display clear on mem and warning

  Hello

  My company bought 5 units of CISCO UCS C200 M2. The servers are equipped with 2 x 6 core 2.67 GHz. The server was also equipped with 32 GB of ram. One of the shows Server alert light yellow on mem and warning on the front panel. Can someone tell what could possibly cause this problem?

  Thank you

  Logan

  Hi Steve,.

  There could be a faulty MEMORY Strip on the system, in the MMIC, you can check the logs SALT (System event log) that will provide you with more details.

  I give advice you open a TAC case for this, we can take a look at the tech show and understand why accurate and if necessary replace the defective DIMM module / part (if defective).

  Thank you!

  . / Afonso

• How can Cisco ucs c220 m4 I start with 12g cisco sas controller? 2012 UEFI Server installation issues

  first time with cisco ucs c220 m4, check my photos

  You have a VD 11TB.

  Only way to start on this is by using UEFI.

  You need to activate UEFI in the boot order.

  Anything over 2 TB and more 4 K sector size readers require the UEFI boot option.

  BIOS will not process the VDs when manages UEFI.

  Kirk...

  Summary for those who seek a similar question:

  • Client a large VD created, 11TB
  • 2 TB and more, 4K sector drives, require boot UEFI + GPT, cannot use the legacy/MBR
  • To set startup to local HD option, that referenced the PCI-E Slot, the raid controller was in (HBA slot in this case)
  • UEFI mode, can't score a VD as "bootable disk / startup.
  • You will see not the VD/raid controller appear in the 'real' boot order during the OS install.
  • Once the installation of the OS compatible UEFI is made, it will create a UEFI boot to the operating system "Windows Boot Manager" entry in our case.
  • After the next reboot, if you check your boot order, you should see this UEFI OS boot manager entry.

• GLC - T allows to connect problem failed validation ucs 6120 and 2960 s (RJ45), are SFP

  Hi, all.

  I use GLC - T to connect ucs 6120 and cisco2960s (RJ45), are sfp validation doesn't have a problem.

  

  I did the speed at 1 G, and then I get error "connection not connected" even, I plugged the cable of nnetwork...

  

  Hello

  I recommend to see if the dealer you bought the glc - t from Exchange.  There seems to be problems with the SFP modules.