Designjet 4000 PS shows error 86:01

Similar Questions

• Designjet 4520 08:11 error

  I looked at the majority of messages about this error, followed suggestions HP, used to my knowledge and still can not overcome this error. I replaced the front hoping it would be as simple as that, but nothing. I then started to replace the pieces one by one. Interconnection of the pca, main Board, HD, RAM and pca of the range. I even swapped the RAM from one location to another in the original map of the mother and the other, as suggested in another post. All with the same 08:11 end result at startup. There is no beeps when turned on and the screen remains white, (except for the contour square) until 08:11 error appears. The green light to the left of the screen will flash green, and the one on the right is red fixed. I tried to lift the diagnostic menu at the beginning, but I am unable as well as access. Any help would be greatly appreciated.

  HP Designjet 4000 Series system error 08:11.

  SOLUTION:
  This system error occurs due to loose connections of the cables & connectors.

  To resolve this issue, follow these steps:
  Turn the power off to the back of the printer and disconnect the power cord

  Reconnect the power cord and turn on the printer.

  Remove all the cable connections between the APC from interconnection and the APC's hand.

  Remove the cable connections between the hard drive, power supply and the APC's hand.

  Make sure these cables are not damaged and room good continuity.

  Remove the module from memory of the APC.

  Remove the hand Print Engine PCA and PCA of interconnection between the chassis and wait 10 minutes for any residual charge will be totally released.

  Replace parts and re-plug all connections of cable one by one.

  Make sure that the module memory is properly fixed in the slot.

  When the printer is in ready state, ensure that the printer has the latest version of the firmware. If this isn't the case, update the firmware to the latest version.

  NOTE: For HP Designjet 4020/4520 serial printer, it is likely higher than the system error is caused by the memory module.
  Memory (if necessary) is the first component that had to be replaced (before hand APC).

• Designjet t125: designjet t125 blue screen error B332347C

  Hello.

  I was ask to get this error:

  When you feed the plotter that blue screen appears with this code: B332347C

  I can't find the service manual for this, if anyone can help me?

  HELO try this solution
  You need to replace hp designjet encrypted t520 chip on the motherboard inside the plotter
  You can buy it on ebay http://www.ebay.co.uk/itm/HP-Designjet-T520-Blue-Screen-Error-Solution-Encrypted-chip/282223353841

• DesignJet 4500ps: is the interchangeable motherboard for DesignJet 4000 and DesignJet 4500PS

  I recently received a model of HP DesignJet 4500 PS broken free Q1272A of friend engineering firm.  The technician, they called to set the printer has assumed that the motherboard (main PCA card) was incorrect and removed.  I don't know anything else other that they decided that it wasn't worth fixing, and the main Board of the APC is missing.

  I think I can get a main PCA Board used for a few hundred dollars, but I have to check that get the right part.  I see the number of room Q1273-60250 being announced as the Designjet 4000 and Designjet 4500.  Can anyone confirm that this is true?  I don't want to buy this part number if it turns out that the Q1273-60250 works only in the DesignJet 4500 if I change it or if I'm just using some accessories.  I also see Q1273-60225 as being for the Designjet 4000 and Designjet 4500.  I found this part number cost very little.  It will work in fact for the 4500ps?

  Any advice?

  Where can I go to be safe?

  Hello

  The 4500 and 4000 share the same hand APC.

  The Q1273-60250 part should work.

  Best regards

  Mike G

• Designjet 4000: HP Designjet 4000 no longer work after Windows update 10.

  We have updated a Windows machine 10 - a new PC DELL Precision T1700 which is only a couple of months.  The update has been problematic with two printers netwoprk, but Canon A4/A3 is now printing.

  Updated since Win 7 lowered 8.1.

  The Designjet 4000 A0 has not printed since and is not found on the network through this machine.

  We looked for drivers, but Win10 won't even allow to install the old drivers: installation fails every time.

  (the original drivers have been in the PC, but I tried to delete to a new facility and since then, cannot install at all).

  Any help is appreciated for busy office!

  Thank you, very good suggestion as it has us going again - no perfecf, but feasible at the moment. Thank you!

• What window updated each time showing error code 00000646 nearly a month what is the solution

  What window updated each time showing error code 00000646 nearly a month what is the solution

  Thank you

  msiddique

  Gives it a try and see if it solves the problem.... http://support.Microsoft.com/kb/2258121

  Let us know if this helped

• My Windows Vist shows error 8024402f update code, impossible to update windows. Help, please.

  My Windows Vist shows error 8024402f update code, impossible to update windows. Help, please.

  Hi you can try the following...

  Click on Start >
  Type in CMD > 
  Right-click on the result, and then click on run as administrator >
  Then type sfc/scannow , and then press ENTER.
  Reboot your PC and try it a few times.

  Download and install the update tool of the system for Vista (Windows Update hotfix)

  • Updated preparation system tool for Windows Vista (KB947821) [February 2012] 32-bit
  • System Update tool for Windows Vista for x 64 based systems (KB947821) [February 2012] 64-bit
  "This tool is being offered because an inconsistency was found in the maintenance shop windows which can prevent the installation of future updates and service packs software."

  Microsoft technical support suggestions:

  Configure the connection to obtain an IP address automatically

  1. Click on «Start», enter "NCPA. CPL"(without quotes) in the search bar and press"Enter. "
  2. Right-click on the network connection, and then click "Properties". If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. Click Select "IP Version 6 (TCP/IPv6)" and then click "Properties".
  4. Check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  5. Click on 'OK '.
  6. Click Select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.
  7. Check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  8. Click on 'OK '.
  9. Restart the computer.

  Other Solutions for error 8024402F

  You can view these articles the Microsoft KB to fix the problem:

  • You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  • Code error Windows Update 80244016, 8024402f, or c80003fa
  • or see this thread

• my printer shows error & or shows offline

  my printer shows error & or watch the printer is offline

  Ronald

  What error does show?

  You have the right drivers and software installed?

  You can run this fix it tool to see if it helps with your problem.

  http://support.Microsoft.com/mats/printing_problems/

• Downloaded windows 10 but not able to install that, due to a problem. now m by downloading again n it's show error 80010108

  Original title: update windows

  I downloaded windows 10 but not able to install that, due to a problem. now m by downloading again n it's show error 80010108. pls help me.

  thanku

  Try to upgrade manually:

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10
  • How to: determine if a device application or hardware is compatible with Windows 10
  • Will remain the documents and applications, or install app must

  then

  • How to download official Windows 10 ISO files
  • How to: upgrade previous versions of Windows using the file ISO for Windows 10

  then

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• Reliance net connector on windows 7, it's show Error 711.

  OT:

  When I use reliance net connect go on windows 7 ultimate it's show Error 711, I tried several ways to solve this problem does not happen. I read all the answers in mycrosoft, I tried, but fails, give me a solution of permanent members of the body of Error 711

  Hi Munasu,

  Thanks for posting in the Microsoft community.

  I suggest you follow the link.
  http://Windows.Microsoft.com/en-us/Windows/get-help-Error-711#1TC=Windows-7

  Keep us updated on the status of your issue and we will be happy to help you.

  Thank you.

• try to install sdk beta4 stunts, always showing error

  Hi blackberrians,

  I am trying to install sdk beta4 stunts, always showing error. I enclose the screenshot.

  I use windows 7

  Kind regards

  Dinesh

  Hey lew.

  Thanks for the reply, I'm already there as an administrator. But I downloaded it again and now it is installed successfully.

  Thank you best regards &,.

  Dinesh

• try to install sdk beta4 nativ, always showing error

  Hi blackberrians,

  I try to install the sdk native beta4, always showing error. I enclose the screenshot.

  Kind regards

  Dinesh

  I downloaded this tool once again, now it is installed

• I can't post pictures on facebook and it is showing error

  I am not able to publish photos on facebook, and every time I try to post pictures it shows error. also I can't order anything online or pay online. It shows the CRDD connection error when I place any order.

  Hello Marie Lise.

  1. SSL connection error are you referring?
  2. What web browser you use to surf the Internet?
  3. If you are using Internet Explorer, version of Internet Explorer is installed on the computer?

  Please answer these questions so that we can help you as best as possible. In the meantime, you can try the steps in the link below.

  Web browsers cannot connect to a Web using Secure Sockets Layer (SSL) site, after you install Microsoft KB2661254

  Hope the helps of information provided. We know the results.

• My system is continually showing error 1723 when removing java, it shows that I have problem with my windows install?

  error 1723

  my system is continually showing error 1723 when removing java, it shows that I have problem with my windows install?

  Help, please...

  and could u please suggest ways to update java for the system and for programming.

  Which version of Java should I download for my system to Windows 64-bit operating?
  http://www.Java.com/en/download/FAQ/java_win64bit.XML
   
  Download errors: 1305, 2755, 1606, etc..
  http://www.Java.com/en/download/help/error_installshield.XML
   
  Installation of Java
  http://Java.com/en/download/help/index_installing.XML?user_os=Windows%207

  Download the appropriate java installation file and save it on HD physically disconnect your computer from the internet, it's true - pull the Ethernet cable or disconnect the wireless connection. Install the installation file java (note: no error message). Back to zero (not sure if necessary, but do it anyway).  Reconnect to the internet and your java work.

• I use windows 7 64-bit edition Home premium and I cannot connect to access database in java program.it shows error database connection driver not installed.

  I am using windows 7 64 bit home premium I installed ms office 2007 and did all the settings.
  but I am unable to connect to the Access database in java program.it shows error database connection driver not installed.
  Please give me the solution...

  Hello

  I suggest you to ask your question about Java programming forums on the subject.

  https://forums.Oracle.com/Forums/Forum.jspa?forumid=922

  You can also ask your question on the forums to access.

  http://answers.Microsoft.com/en-us/Office/forum/access?page=1&tab=all&TM=1349633636662