Designjet 4520 08:11 error

Similar Questions

• DesignJet Scanner 4520: Designjet 4520 Scanner network problems

  I have a Scanner of DesignJet 4520, that very recently stopped working on the network.  Wiring to the scanner is good and the network itself works normally.  I can't get a DHCP address or assign a static IP address to the device.  When I try to assign a static IP address, I get the following error:

  56-62 an error occurred when applying network settings. Check that the entered parameters are valid for the network.

  Thoughts?  Is my scanner goes wrong?

  Looks like you have a Rev A scanner and the software is for the Rev A and B

  The SW is 24.1 the the file name once you have created the bootable image and make sure they match

• Designjet t125: designjet t125 blue screen error B332347C

  Hello.

  I was ask to get this error:

  When you feed the plotter that blue screen appears with this code: B332347C

  I can't find the service manual for this, if anyone can help me?

  HELO try this solution
  You need to replace hp designjet encrypted t520 chip on the motherboard inside the plotter
  You can buy it on ebay http://www.ebay.co.uk/itm/HP-Designjet-T520-Blue-Screen-Error-Solution-Encrypted-chip/282223353841

• Designjet T120: HP T120 error BA7F11E0 designjet

  We have a HP designjet T120 when power on/off, this (BA7F11E0) error message appears on the screen immediately.  No movement of transport or initialization is performed. Just the error and nothing else. Pls help.

  Thank you

  Hello

  Try to isolate the printer, remove the printhead, inks, connectivity cables and turn on the printer.

  If the error persists, it may be a problem with the APC hand.

  Best regards

  Mike G

• DesignJet 5500: firmware update error

  The firmware on my printer is: S.03.12D

  I went to this URL:

  http://h20566.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=82219 & swLangOid = 8 & swEnvOid = 181

  and downloaded the firmware under Windows 2000, even if I have Windows 7 64 bit on my computer because I thought that the firmware was just download to the printer, so it should matter what OS is on the computer.

  I downloaded S.56.07 February 3, 2009

  I downloaded the firmware to the printer file and it improved up to 97% and then gave the error message below.

  An unexpected error has occurred. Make sure that the firmware you are using is a valid firmware file.

  I have a Designjet 5500 and I went from dye in ink UV, if that matters.

  The printer seems to be ok, but it would be good to know how I can upgrade the firmware.

  Yes, a connection between the computer and the printer is recommended.

  Version of the OS is not the problem here, but exact number of the product will make a difference, so please use the actual peripheral product number.

• Designjet 4000 PS shows error 86:01

  Hello

  I bought a Designjet 4000 opportunity. He came, I started the printer and it started printing a testchart with colors about 30 x 40 cm. Then it stopped and showed a 86:01 error. There is no paperjam, but the belt was in very poor condition. So I changed the belt, but the error still occurs.

  As a precaution, I changed the encoding Strip, but the printer showed error

  Test run of axis of scan in the works of service for a long way mode. The movements of the printing in the Middle unit, can be moved by pressing the arrows, he tries the printway by moving to the left and to the right, the distance ist ok. If you come from the right side after that, he moves about 10 cm and stops with an error 86:01.

  The display shows the long version of the error:

  Code: 0 x 18010001

  Severity: error

  Priority: 3000

  ID: 0x101021a

  Description: STRING_MEDIA_JAM

  File: CarriageServoMotor.c

  Line: 1537

  Class: Scan axis

  Subclass: movement

  Error: Transport jam

  Set: DRACO_SCAN_AXIS_MOVEMENT_JAM

  Description: Jam of transport

  Of course, I cleaned and oiled the stem and sliding. The trolley can be moved smoothly, I would say.

  I changed the motor, belt - no change. I called HP Support, they commended for changing the diet, I have still no change.

  I don't understand, the printer worked first with a belt of poor and now in test mode flies over all printway for several times before running into error. And modifying in part after part on spec, will be a costly way, I think. Any idea? Thank you.

  After changing many elements - the reason was the new belt! I would say, I have no HP original, but a part of China. Unfortunately I can't prove it, but after changing the belt against the original, the error disappeared.

  Thanks a lot for your messages.

• HP ENVY 4520: SETUP PRINTER ERROR?

  I got this error message when you try to download the drivers to install this printer HP Envy 4520:

  Call to DriverPackageInstall returned error 5 for package "C: / Prgram files/HP/HP ENVY 4520 Series/Driverstore/NGScanDriver/HPNIA_EN4520.INF."  A caller of DriverPackageInstall must be a member of the Administrators group to install a driver package.

  What the hell it means, and how should I do to fix this?  All ideas are welcome.

  Thank you

  Deb7325

  Hey @Deb7325, welcome to the Forums of HP!

  I would be happy to help you install your craving 4520. If I understand your description that you see "Call to DriverPackageInstall returned error 5 for package" C: / Prgram files/HP/HP ENVY Series/Driverstore/NGScanDriver/HPNIA_EN4520.INF 4520.  A caller of DriverPackageInstall must be a member of the Administrators group to install a driver package. "When you try to install the software.

  You are the administrator on this PC, or you logged in to the Admin account? If this isn't the case, please ensure that you install on the Admin account.

  If you try to install on the Admin account, please perform a clean boot and try to install again. If you need help by performing a clean boot, click the following link: How to perform a boot in Windows.

  If you are still not able to install the software, let me know and I will do everything I can to help. If this resolves the issue, please be sure to mark your post as solved by clicking on the accept button Solution below. Thank you.

• HP DesignJet Z6200 plotter ink error - ink appearing

  I print the cards on a large scale on a plotter HP Designjet Z6200 and ink blots are appearing on the side. While the tasks are not printing itself, it always indicates an error. In addition, on diagnostics test print only, some of them does not appear (it is not on any other impression here yet).

  

  

  Ink absorber?

  Clean print heads?

  Any ideas?

  Hello

  You have a bad printhead.

  If they are under warranty, call HP, share these photos and ask for replacements.

  If they are not in warranty, you can purchase them directly on any store reseller or HP.

  I will recommend you to stop printing until you replace the print heads, because you may damage the maintenance cartridge, the vacuum system, contaminating the milling table, etc., everything about contamination due to a leak of ink.

  I hope this helps

  Best regards

  Mike G

• DesignJet T2300 firmware update error

  When you try to update the firmware I get the error message: manifest of updating the Firmware file does not.  The firmware update was interrupted.  Firmware version is IG_02_00_15.1

  Any suggestions?  (just unboxed this plotter today!)

  Never mind... set to update to the latest firmware using a USB key instead of the network.

  All right.

• DesignJet 815 mfp 2007 error cannot write to device

  We get this message on the touch screen when you try to copy. All other functions work correctly. Unfortunately the detailed resolution of the "Try Again" does not seem to correct the error.

  Any ideas would be very grateful to you. Thank you.

  Issued or resolved.

  I found that the printer (815) was not selected as the default printer. When I chose it now all copy as it should.

• right of the Designjet printer door open error 3500cp

  Hello

  I have a range of designjet 3500cp printers. After that I turned on the printer (which is not connected to a computer), it is said right the door is open and I have to close it to continue. The door is closed and tried to trick the printer by pressing the small lock with a screwdriver, but that did not work. Also, when the printer is finished initialization and right before the message lights, the printer makes a clicking like the printheads noise moves, but then get stuck or stop.

  Thank you in advance.

  I just want to let anyone have a similar problem to know that I fixed that. It turns out that the ribbon cable flat on the control panel (screen which displays messages) was a thread that was torn a bit. So, I used an exacto knife to separate this individual thread. Then I cut, where it was torn so that I can remove the rubber covering to reveal the thread under and then enclose it with a new wire to the ends of it so that I can establish a connection. Then I turned on the printer and it worked. I'll upload a youtube video or a process diagram, but it saved me $120 in the purchase of a new control panel.

  Basically, the two sensors or microswitches have sons (ground floor and hot) that connect to the control panel circuit and the circuit is a dish that connects to the main circuit on the pack. When the flat ribbon had a small tear on this subject, the right door sensor is absent. The dish is also persevered in the CB Panel. in any case, hope this helps someone in the future.

• DesignJet 1055 CM path error msg

  Just finished replacing the belt according to the manual. set the table plotter back together and turned on. After auto checks are completed it begins to initialize and then I get the display "turn the power off. Check the path of the print head. 1 "

  I've checked everything and still get this message. I had a lot of rubber dust I cleaned before putting the new belt and also used the applicator of oil on the stems roadrunner front back together.

  Help.

  The coding Strip was not sitting in the Groove on the print head.

• HP Designjet T120: T120 Designjet error HP: 805D06E31

  Hello

  My HP Designjet 120 gives the error code: 805D6E31.

  I tried to install the new drivers, but my printer will not be available in the Hp Utility tool.

  Of course, tried to reset it but you need the touch screen for this. which displays the blue screen.

  Any solutions guys?

  Found the solution.  The plug was defective.  replaced and it worked.   @HP - please get this error on a Web page code, sound very confusing and it is illogical that this error code is not traceable at all.

• Designjet 5500: HP Designjet 5500 - failed hard drive?

  My next plotter Designjet 5500 has the error message: "failed to start.  Error: 1f50007.  Hard drive failure. "I took out the hard drive.  Then I took a good hard drive on another plotter Designjet 5500 I have here (he has other issues, but the hard drive is in good health) and installed it in the abacus of 1st.  He repeats the same error message (i.e., "failed to start.  Error: 1f50007.  Hard drive failure. "I took that hard drive back out and put back in 2nd tracer and it always starts very well.

  For me, this means that probably the hard drive is not really the problem with my 1 tracer because I put a hard drive perfectly well in and he said that the hard drive has failed.  It seems that something has no who is now saying the plotter that there a defective hard drive when it's not the real problem.  Someone else this experience?  Pointers for me on what to look for or what would be my next step in troubleshooting?  Not covered in the manual on the defective hard drive errors.  Only how to remove and install a.

  Thank you.  Erica

  Unplug the printer.  Loosen the screws and remove the print server plug at the back of the printer (he shoots just to the outside), then take the back cover off long.  Look for the two lights, amber and one green on the circuit on the left.  Lights are on the top left of the Board of Directors (main PCA).  If you do not have both lights then it is most likely doesn't have the power of power supply Board (the circuit board to the right of the hard drive).  My experience has been that when the power Board fails, the error you see is that the hard drive will not start.

  If you have already tried a known good hard drive and have the same defect, it is most likely the problem.

  Tell us what you find.

• I am a technician working on a HP design jet t920, desplays error restart 21:13

  HP designjet T920 broadsheet desplays error 21:13 before initialize completely and restart if persist contact for service. I tried to clean and lubricate the machine but no change. Kindly help

  Newsyl3

  Hello

  The error is related to the Station (SS)

  Look for any obstructions

  Clean the MICR band to make sure that the ramasseherbe is not on the wrong place when the SS moves

  If you have noises coming from the SS, when he tries to move or does not move, you may need to replace the part