DeskJet 3634: Deskjet 3634 automatically prints on the test at startup page

Similar Questions

• HP Deskjet 845c stopped printing in the middle of a job and don't print any more

  My deskjet 845c was printing fine and then suddenly stopped printing in the middle of a page. The power light is on and steady, and the orange light blinks.  I can't print at all at the moment.

  I followed the troubleshooting listed using the HP diagnostic Print and have removed and cleaned the ink cartridges, but the orange light still flashes.

  Any help you could offer would be greatly appreciated.

  Thank you.

  It seems that one of your cartridges has failed.  I don't remember if the printer Deskjet 845c is printed in reserve with a deleted cartrdige mode.  If you then remove the cartrdige color and try to print a test page.  If this works the cartrdige of color was at fault.  Otherwise then reinsert the cartrdige color and remove the black cartrdige and print a test page.  It worked?  If so, the black cartrdige is at fault.

  If the printer will not print with a cartrdige deleted then I would replace the black cartridge with a replacement fee.  My experience suggests that the black cartrdige is usually the culprit...

• HP Deskjet Ink Advantage 1515: stop the test page printed for all-in-one printer, HP Deskjet Ink Advantage 1515

  How can I stop my HP Deskjet Ink Advantage 1515 all-in-One printer to print a test page everytime I STARTED printing?

  Hello JoshSimon ,

  Welcome to the HP Forums.

  I see that you have a problem with the printer printing before you print a test page.

  If you turn off the printer at the end of the day, please do not.  Turn the printer on/off will result in printing a test page.  If you are concerned about the printer lost power, and that's why you stop, the unit actually built in sleep/stand mode that will kick in when you are not using the printer.

  Once a print job is sent to the printer it then wake up and do the task at hand.

  In addition, make sure you have the printer power cable connected directly to a wall outlet and not a bar/power strip. Here is a document that uses a LaserJet printer for example, but it is intended for HP products in general. Please click the link which explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  See you soon,.

• All-in-one printer, HP Deskjet F4480 cannot print from the INTERNET?

  You encounter problems, printing from the internet HP Deskjet F4480 all-in-one printer?

  Sometimes nothing prints, part of the page is missing, print headers only and etc. No worries, I have a document that can help you with this problem.

  This link will provide you with the differenct steps that will solve this problem.

  http://support.HP.com/us-en/document/buu01105

  If you have any questions, feel free to ask. I hope this helps.

• HP Deskjet 1510: Duplex printing problem - an odd number of pages only

  If I print something with 8 or 12 pages or whatever (numbers) everything works perfectly.

  For odd numbers of 9 or 15, or whether, it becomes a bit like a random number generator. Page 1 is ok, but the rear where need to go 2 can be empty, could be page 4. The last page prints on the last page which must be empty.

  If I have a 9 page document that I can choose pages 1-8 and then separately just print 9 and it works well.

  Hey @terry6,

  I see you have some problems with the printing of your Windows Vista computer to your Deskjet 1510. Now, a printer only prints what the computer told him to print, but I can help you find the problem on your PC.
   
  Here's what we will do:

  1. Turn the printer off.
  2. Close all programs on your PC.
  3. Open your control panel, and then printers and faxes.
  4. Right click on the image to the printer.
  5. Click on remove the instrument.
  6. Repeat if you have copies of your Deskjet 1510 listed.
  7. Turn on the printer.
  8. If the printer does not appear in this window after you turn on the printer and wait a few minutes and then click Add a printer up.
  9. Follow the prompts to add the printer to the back.
  10. Try to print again.

  This should fix your problem with printing pages in the right order. If it does not then try the following:

  1. Uninstall and reinstall the printer.
  2. Uninstall and reinstall the software, you are printing from.
  3. Try another program.

  If he let so please other users know by clicking on accept as Solution below my post. Even if you have any other questions please let me know.

  I hope this helps and I hope you have a great weekend!

• HP 5150: After each print job, I get a "printed in the test document. How to stop the test sheet?

  After each print job, I always get a 'test page print '.   I don't know how to stop printing. Any ideas?

  Hello

  ·         Using the HP Deskjet 5150 color inkjet printer or all-in-one printer, HP Photosmart C5150?

  ·         Were there recent changes made on the computer or the printer before the show?

  Follow the form of measures troubleshooting article and check if that helps.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  See also:

  Resources for the resolution of the printer in Windows XP problems

  http://support.Microsoft.com/kb/308028

  If the problem persists I suggest you contact HP support for help:

  http://WWW8.HP.com/us/en/support-drivers.html

• HP Officejet Pro 8620: Im a line is printed to the bottom of each page I copy via adf, including analyses

  Everything I insert through the adf comes out with a dark line printed to the bottom of the page, including pages that are being analyzed?

  This is caused by a specification on the thin piece of glass to the left of the main bed.  Clean this area, it will solve the problem.  It can help to use a strong flashlight which is held parallel to the glass to highlight the area that needs to be cleaned.

• How can I print only the part selected a page?

  When I highlite prints part of the entire page. How can I print only the part selected page?

  Try:

  Highlite your text

  Press CTRL + P to start the print menu

  "All" is selected by default in the scope . Change it by selecting 'selection ', and then click OK.

  This example shows only the text that is selected. Microsoft® Security MVP, 2004-2009

• OfficeJet Pro 8600 N911a is no longer prints except the test page or status report

  The object printer worked fine until today when it stopped printing from my Macintosh computer.  I am able to print very small application PAGES but message with any normal print job, I get the following messages:

  The printer ready

  Preparation print

  Connected to the printer

  Print page 1

  (slight noise of printer)

  100% full

  The printer ready

  In other words, she almost immediately jumps to 100% full when in reality it has not yet started printing.  It then acts as if it was ready for an another print job saying printer ready.

  DonovanH thanks for your help.  The result is that now the printer works because of some experiments I did.  I pass the steps you suggested and I still had the problem, but further experiments showed that the pages that would be printed not had a warning that they are associated with "character borders are not supported and were removed.  I don't know why this document in particular has these problems, but I find that all documents without such warning prints fine except that they seem to often slower than expected.  Any document with this warning indicates quickly as it's done 100% but it does not print.

• Can't print in the center of my page

  I'm no stranger to InDesign, but I just took a new job with a lot more applications print. I am now in charge of the production of the finished product. I print simple things like postcards, where I have two identical images on a single page. I then cut the page 8.5 x 11 in half and have two postcards. It's ALL I want to do, but considering that for the life of me I can't understand how to keep the image centered when I print, I'll have to do more cutting. Even in this case, it seems bad. Any advice?

  He could make a difference which stok of paper you are uusing and drawer from which it is drawn. These animals can sometimes be fickle...

  Your probably also has RIP of settings for you to move the image on the page and at the level in both directions.

• Automatic connection to the server at startup for VMware View Client 2.2 Horizon?

  In iterations (5.x), there was simply an option in "always connect to this server on startup". 

  
  

  In test 2.2.0 I don't see that option anywhere. I have also yet to find any switch that I can add to enable this feature.  Does anyone know if this is even possible?

  
  

  Thank you

  You can create a custom shortcut that bypasses the user selects server connection: "C:\Program Files (x 86) \VMware\VMware Horizon view Client\vmware - view.exe ' desktopProtocol - desktopLayout - fullscreen PCOIP - serverURL 'view.connection.server.url' logInAsCurrentUser - false

• Drive hard short DST failed the test at startup

  I use a Compaq Notebook PC CQ58 and were not able to boot from the tenth day of may I'm in Windows 8.
  I tried to understand what was wrong and used F2 for boot test. My "short hard drive DST' has no amd I don't know how to solve this problem, can someone

  Hi Hank,

  F2 to start test is a feature on HP computers to check if there are problems with the hardware components of the computer. DST short for hard disk error means that there is a problem with the hard drive and must be replaced.

  If the computer is under warranty, you can contact HP Support and get this replaced and if the computer is not under warranty, you can buy a new hard drive for this computer and get this fixed number.

  If you need additional information, you can come back.

  Concerning

  MathewT

• HP Deskjet 1010 does not print on the web

  My Deskjet 1010 new print from the software I have installed fine, but when trying to print a size on the web there is nothing even if all options come to print.  What Miss me?

  Hi, have you tried using another browser?

• DeskJet 5550 cannot print the page to clean cartridges.

  DeskJet 5550, Win 7 64 bit, after clicking on the clean print cartridges, it does nothing. Power light is solid on. The menu box arrives with Click clean to clean the cartridges now. Clicking on clean makes this area of empty menu and nothing happens. No error or no program has stopped responding. Can the text and images fine print except that I need to run the utility for a few minor flaws. Past to the best setting which helped a lot. Does not print the calibration page either. Prints all the tests and the test page.

  I believe you can force a cycle of cleaning as follows: power on press and hold the power button, press on and release the button X twice quickly, then release the power button.  No page will print, but you should hear the printer to clean.  A more aggressive cleaning can be done by pressing the X button twice and once the page break button, a still more energetic cleaning by pressing the X button twice, then press the page twice break before releasing the power button.

  You can print a diagnostic page holding the power and then button by pressing the X button eight times followed by the button to jump to page four times, then release the power button.

• Need Win 7 driver for my HP Deskjet 1000 c printer.

  I need a driver for Windows 7, 64-bit, please, for my HP Deskjet 1000 c printer.  Printer is old but works well with XP and large format.

  Thanks to all those who can help you.
   
  Original title: hp deskjet 1000 c

  Hi John,.

  You can download the driver for HP Deskjet 1000 c printer on the manufacturer's Web site.

  Check out the link: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=4066377#N216

  If the problem persists, I suggest you contact HP support for help.

  http://h10025.www1.HP.com/ewfrf/WC/contacthp?CC=US&DLC=en&LC=en&os=4063&Product=4066377&sw_lang=

  Hope this information helps. If you need more assistance or information on this question, reply to this post. I'll be happy to help you.