Desktop very very very slow in anyway, installation of windows or open my computer or install the driver and everything

Similar Questions

• Very slow to load on a Windows Server 2012R2 PowerCLI

  Hi all

  PowerCLI 5.5 is very slow to load on my Windows 2012R2 server, I did a few tests

  Test 1 - load the snap of PS on my worstation (8.1 for Windows 64-bit - SATA hard drive)

  PS C:\Users\MyUser > Measure-Command {Add-PSSnapin vmware.vimautomation.core}

  Days: 0

  Hours: 0

  Minutes: 0

  Seconds: 1

  Milliseconds: 871

  Ticks: 18717065

  TotalDays: 2.16632696759259E - 05

  TotalHours: 0.000519918472222222

  TotalMinutes: 0.0311951083333333

  TotalSeconds: 1.8717065

  TotalMilliseconds: 1871.7065

  Test 2 - snap of PS of load on a 2012R2 Windows Server not connected to the internet, check on CRL

  PS C:\Users\MyUser > Measure-Command {Add-PSSnapin vmware.vimautomation.core}

  Days: 0

  Hours: 0

  Minutes: 0

  Seconds: 51

  Milliseconds: 603

  Ticks: 516030768

  TotalDays: 0.000597257833333333

  TotalHours: 0.014334188

  TotalMinutes: 0.86005128

  TotalSeconds: 51.6030768

  TotalMilliseconds: 51603.0768

  
  

  
  Test 3 - support software component PS plug-in on a Windows Server 2012R2 not connected to the internet, check CRL disabled

  PS C:\Windows\system32 > Measure-Command {Add-PSSnapin vmware.vimautomation.core}

  Days: 0

  Hours: 0

  Minutes: 0

  Seconds: 16

  Milliseconds: 323

  Ticks: 163238507

  TotalDays: 0.000188933457175926

  TotalHours: 0.00453440297222222

  TotalMinutes: 0.272064178333333

  TotalSeconds: 16.3238507

  TotalMilliseconds: 16323.8507

  As you can see there is an improvement when I disable CRL checking in accordance with this article: http://blogs.vmware.com/PowerCLI/2010/01/troubleshooting-slow-startup-with-powercli-40-u1.html

  But I still have 16 seconds to load the snap against 1 second on my workstation (which has much less computer resources!)

  Any help is appreciated.

  Hi LucD,

  I've found a workaround:

  When I run the import-PSSnapin I noticed (with wireshark) a lot of traffic failed to WAN addresses, so I set myself, in Internet Options a false proxy (127.0.0.1), excluding the proxy DNS of my domain active directory name (so I can connect to the virtual center without going through the wrong proxy)

  Now is the time of execution:

  Windows PowerShell

  Copyright (C) 2013 Microsoft Corporation. All rights reserved.

  PS C:\Users\MyUser > Measure-Command {Add-PSSnapin vmware.vimautomation.core}

  Days: 0

  Hours: 0

  Minutes: 0

  Seconds: 2

  Milliseconds: 774

  Ticks: 27745259

  TotalDays: 3.2112568287037E - 05

  TotalHours: 0.000770701638888889

  TotalMinutes: 0.0462420983333333

  TotalSeconds: 2.7745259

  TotalMilliseconds: 2774.5259

  Not bad! Execution time lowered 16 sec at 2.8 sec

• Printer installation error (could not install the driver, error 28)

  I just bought a new printer (Epson XP-204) and tried to install it on my laptop Dell XPS15 (running edition W7 home 64-bit).

  After you have installed the software and drivers, I connected the printer to a USB port, Windows detects it and started to install the driver. After a few seconds, I got an error message telling me that it was an error and the driver could not be installed (error 28).
  I managed to make the printer works by using its WiFi connectivity, but now, I found ALL my USB printers have disappeared and I can't use it anymore. Whenever I plug a printer into the USB port, I get the same message with error 28. What is happening on printers that worked very well until I tried to install the new Epson in the USB port.
  I tried to restore the system to the State prior to the installation, but the system restore fails to complete and return an error message.
  All my USB devices work ok (mouse, storage, debuggers, etc) the problem only occurs with the printers.
  I tried to start in safe mode and remove all USB devices, but after mounting them again once the error occurs again.
  I don't know what else to do (reinstallation of the operating system is not an option, and if I do, I swear I'll go to Linux).
  No idea?

  Hello

  Problem solved!
  After reading this page: http://www.asyndetic.com/blog/2010/02/06/debugging-usb-device-installation-on-windows/ I found it lacking the USB.inf file in my system too (I don't know why or how it has been deleted).
  I copied the file from another machine, removed the printer in Device Manager, rescan the devices and Windows found and installed all the drivers with success!
  Thanks for your time,
  Fabio Pereira

• Not changed map of video on HP m8400f desktop; Cannot install the Driver

  Card video NVIDIA GeForce 8500 GT to my HP Pavilion m8400f Desktop computer has failed. replace the defective video card with an NVIDIA GeForce GT 610 video card.  Display is back, but now the computer is SUPER SLOW.  I can't get access to enough RAM to install the CD for the driver for the new card!  Tried Safe Mode - could not install the software driver on the CD.  Simple operations (such as opening Windows Explorer) is about 3 minutes.  The HP Startup Repair utility takes forever.  I want to run Norton Antivirus, but the computer is so SLOW that it takes an hour to see my desktop icons.  I put my old card back video; the graphics have been shredded as 'The Matrix' and startup performance was just as slow.  Any suggestions (in addition to buying a new computer)?  Can't the basic functions of Mode safe without the video card?

  (Sigh) Given that the CPU of the computer of my 6 year old works 100% (even with only a race application), I decided to cut my losses and buy a new HP Envy 700-327c desktop PC.  In the meantime, I do backups of files from my old PC to an external hard drive; What was once taking 10 minutes is literally take 10 DAYS because the CPU is running so SLOW.  Thanks for your help.

• I want to activate an installation of creative cloud on 1 computer to install it on a laptop more recent. How can I go about it?

  I want to activate an installation of creative cloud on 1 computer to install it on a laptop more recent. How can I go about it?

  Open your desktop cc app and disconnect, http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  or you can simply connect to your cc on your 3rd computer desktop application and it will give you the opportunity to sign out of your other two computers.

  If you need the application of cc, Download Adobe Creative Cloud apps desktop | CC free trial Adobe

• Hi, I am Ganesh, I tried to installed the application using creative cloud. But seems it's taking too long to install the application and it is hit. After the installation of 42%. Still, I tried to restart my computer and re-install the application. But i

  Hi, I am Ganesh, I tried to installed the application using creative cloud. But seems it's taking too long to install the application and it is hit. After the installation of 42%. Still, I tried to restart my computer and re-install the application. But it is keep taking so long time and struck at the end of the installation of 42%.

  If the installation process is stalled at 42 percent with no possibility of error, there is a problem with the zipped file to Extraction of downloaded in the Temp folder.

  As a fundamental step. Leave the creative Cloud desktop application.

  Delete the contents of the Temp folder:

  Optional: it will be ideal to install software like Winrar, WinZip or 7-zip,., etc.

  Please press Windows + R and you will get a command window run, get hit and type %temp%.

  Delete all the content inside the temp folder.

  
  

  
  Then try again to install application InDesign CC again.

  Just in case, if you are still having the same issue.

  Creative application cloud thus released, do not close it.

  Open the Temp folder, then search for the CC InDesign installation file and copy it to the desktop computer.

  Then leave Creative Cloud application and try to install.

• Whenever I open my computer I get the following message is displayed as a pop-up on the desktop: C:\PROGRAMA~2 Kodak\EasyShareSetup\$Regis~1\Registration_7.2.20.2.stx

  Whenever I open my computer I get the following message is displayed as a pop-up on the desktop: C:\PROGRAMA~2 Kodak\EasyShareSetup\$Regis~1\Registration_7.2.20.2.stx I don't have Kodak on my computer and I typed Kodak in the search above Start section and checked my programs.

  How do I get this off of my computer?  Any suggestions appreciated woul

  I typed Kodak in search above to start section and checked my programs.

  Instead do with msinfo32.exe to open system information.   Then, in the Environment\Startup software do a find, category searches only for Kodak

  Even better would be to use AutoRuns (utility system available on TechNet).

  HTH

  Robert Aldwinckle
  ---

• I am trying to install ION Slides2pc scanner. When I try to install the driver, I get a message "system administrator has established policies of prevention of this type of installation. All the answers?

  I'm trying to install the software for a slide ION Slides2pc scanner.  When I try to install the driver I get the following message "system administrator has established policies of prevention of this type of installation.  All the answers?

  Try right click on the installer and selecting 'run as administrator '.

  Support http://www.ionaudio.com/support ION

• Try to install the software and I get an error message saying that the installation cannot continue because a previous installation requires your computer needs to be restarted.

  Original title: .net framework 4.6

  I try to install the software and I get an error message saying

  Setup cannot continue because a previous installation requires your computer must be restarted. Restart your computer and run the Setup again.

  so I restart my pc and run it again and the same message appears

  Try to perform a "clean boot" to start Windows by using a minimal set of drivers and startup programs. This will eliminate software conflicts that occur when you start Windows, install a program or an update or when you run a program in Windows.
  http://support.Microsoft.com/kb/929135

  Perform a clean boot to determine if background programs are interfering with your game or other programs
  http://support.Microsoft.com/kb/331796

  One by one add back an application both in the boot list to find the software application incriminated.

  J W Stuart: http://www.pagestart.com

• I uninstalled by mistake the installer of windows 7. How can I install downdload?

  I uninstalled by mistake the installer of windows 7.  How can I install downdload?

  Troubleshoot Windows install

  2438651 how to solve problems that may occur when you install, uninstall, or upgrade a program on a Windows computer

  http://support.Microsoft.com/kb/2438651

  Substitute:

  Unregister Windows Installer and then reregister Windows Installer. To do this, follow these steps:

  1. in the menu 'Start', click on ' execute:.»

  2. in the "Open" box, type "msiexec /unreg", and then press ENTER.

  3. in the menu 'Start', click 'run '.

  4. in the "Open" box, type "msiexec/regserver", and then press ENTER.

  If this is insufficient, the I would say to install the Windows Installer Cleanup utility and run that to remove the Java remains Setup files that can cause problems with your current installation.

  For more information, visit the below mentioned link:

  http://support.Microsoft.com/kb/290301

  ------------------------

  Click Start Orb, in the box, type search: Regedit.

  Highlight: HKEY_lOCAL_MACHINE/SYSTEM/CurrentControlSet/services/msiserver

  Verify that the SYSTEM account has full control. If it does not, add the SYSTEM account with full control.

  Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk.

• I would change a few pdf, I created. I downloaded (acrobatproDC_00000000000000000000000409.exe) and then did the installation. but when I opened one of my docs, the Edit option not there. What have I done wrong

  I would change a few pdf, I created. I downloaded (acrobatproDC_00000000000000000000000409.exe) and then did the installation. but when I opened one of my docs, the Edit option not there. What have I done wrong

  Uninstall what you have downloaded.

  If windows, clean it by Download Adobe Reader and Acrobat tool - Adobe Labs

  Reinstall the correct version for which you are authorized to use another browser.

  Available downloadable Setup files:

  • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | Suite X | 9,8 | 9 pro extended exe,7z extended pro 9 | 9 standard | 8 standard
  • Captivate: 9 | 8 | 7 | 6 | 5.5, 5 | 1
  • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2
  • Lightroom: 6.6.1. 6| 5.7.1| 5 | 4 | 3
  • Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
  • Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Satellite A85 S1072: Very slow OS after installation of new

  Hello
  I have problem with my laptop. It is a technical issue. Recently, my system crashed and I reinstalled system, now I have problem with speed and works, when I install some programs or copy the file into different space, the system is slow and it's look like a block for a while.

  example: I have 2 partitions when I copy a large file like 400 MB of partision partision 1 2 I have like 50 kbytes 1200 KB transfer.

  I tested my system with the tool of diagnosis PC Toshiba program and he said: it's an OK status with the material. I used some more flavor called Easy Recovery professional programs to test my hard drive and the status is OK.

  What do you thing about my problem. That's the problem with my hard drive or motherboard? you know any problem to test some of those things to help me.
  Very thanks for the reply.

  Next time.

  Notebok parameters: 256 ram, 40 GB drive, processor 1.4 GHZ.

  Hello

  Your device comes pre-installed with a Toshiba recovery media?
  I would recommed to check the HARD disk.
  You can try to use some HDD monitoring tools. Googled around.

• ISE Posture Windows enter password to view the desktop very slow

  Hello, had a problem of slowness that I don't know how to solve problems.  ISE 2.0 patch3, AnyConnect 4.3.02

  My setup is Anyconnect which is already on the computer windows laptop 10, EAP with TLS chaining for authentication of the host and PEAP for user auth.  ISE Posture checks for windows AV defs and AV windows install.  AnyConnect has 'start before logon' installed and * just work *.  Boots of the user, auths from the machine before the connection of the user, user logs in and ISE Posture check runs and passes.  The user gets the green checkmark on the line.

  With a little problem.  At the time wherever the user types the password and hit enter, the grip of the Welcome screen for about 45 to 60 seconds, a few rare occasions longer, my high water line is 1 minute 12 seconds.  Meanwhile machine auth and auth user spend with the unknown state of compliance in the live of the radius of ISE log.  Then welcome screen disappears and the bureau paints (finally), at this time, the machine cannot access anything on the network, 5 seconds later the Anyconnect client starts.  1 second later the bumps network connection, and the analysis of the Posture of ISE in the Anyconnect client starts.  Analysis of the Posture of the ISE takes about 7-10 seconds to complete.  After that everything is good and the user can access the network.

  If control of Posture of ISE is deleted, the whole process takes 10-15 seconds password entry the user to be able to use the laptop and access the internet.

  Does anyone have an idea whence this 'start delay '?  Feels like a timeout of some sort.  It happened on this latest version of the Anyconnect and 3 previous ones as well.  I concentrate on my test machine windows 10 laptop, but the same thing happened on 4 other test systems which are a mixture of windows 7, 8.1 and 10.  The 10 win test system is a lenovo x 1 carbon with an SSD and is normally fairly quick.

  All the tips are greatly appreciated.

  e-

  Do you have the port in a vlan to auth machine and then change once the machine and the user connects? Also, you will probably need to open any acl you apply while the posture is 'unknown '. It is usually due to some AD access that is blocked.

• Very slow access to network between Windows 7 64 and XP 32 readers

  Nice day

  Recently, we have replaced a dying man computer of Windows XP with a new Windows 7, i3, 4 GB RAM with full 100Mbit network card, which is operating quite smoothly. This computer has a very necessary shared folder, the folder F1000.dta for Acomba, what is needed by other users. One of these users work with a 32-bit of Windows XP Professional SP3 with 2 GB of RAM and 100Mbit ethernet card. Given that its a 7 / XP share, all sharing on the Windows 7 computer options have been configured (only show network, sharing of citrine, no password, etc...)

  The problem now is that while the shared folder is visible, mapped as a network drive, it takes about 5-7 minutes to open the mapped "drive/folder" and a 1-2 minute goo whenever one of its subfolders is accessed. I tested the cable connecting the computer to the network with 3 laptops (running Windows 7 Starter Edition, Vista Home and Vista Ultimate) and all were able to access the drive a few seconds (for 7 Starter) for a decent 10-15 seconds for Vista machines.

  Acomba, it should be noted, does not work from this mapped folder, but is installed locally on each computer. Only the file data that contains the documents of the company for Acomba, is shared and accessed remotely.

  Is this a normal problem between XP SP3 32 bit and 64 bit of Windows 7 Professional, or am I wrong configured something?

  Thanking you in advance,
  Greg Jean-Louis

  Hello

  Journal of computers support sites download the latest NIC drivers and force the installation.

  Download the drivers and extract them to a folder of your choice.

  Since an Admin account.

  In Device Manager, right click on the adapter, http://www.ezlan.net/Win7/net_dm.jpg

  Click Update drivers and choose her browse my computer for drivers.

  Choose let me a list of choices, click on disk and point to the folder with the drivers.

  -----------------------

• Pavilion 550qe Desktop: is the extensible desktop Pavilion 550qe computer of SSD HARD drive and also increased the RAM?

  I buy the HP Pavilion 550qe desktop computer, and it will come with a 1 to HARD drive and 8 GB of ram.   I'll be able to open and pass at the disk for one SSD... and also, can I replace the 8 GB of RAM for 16 GB?   Is RAM welded in, or is it replaceable?  I heard that HP is very difficult to spend at home, this is true even with desktop computers?

  You are welcome!

  Yes, you can upgrade the memory.  There are two locations of memory on the motherboard.  This is the page for Specifications of the motherboard of the computer.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.