DHCP client/server problem

Similar Questions

• I can't find the ip address of the print server on my router, DHCP clients

  I got the wireless-g WPS54G print server at a yard sale and have downloaded the Setup Wizard.  Everything looks fine until step 7, select print server.  Could not find anything.

  Before that, I tried to access the print directly through its ip address server, but can't get it.  I checked all the IPS on the main router and found everything except the print server.

  Everything is setup, more than once, exactly as defined in the steps of the installation wizard.

  I have Windows 7 and a computer laptop 64 bit.

  Any suggestion would be great.  I already spent 2 hours on this thing and am determined to make it work.  All the lights on top of the blink/light print server as it should when they should.  I was not wireless yet, still trying to get this Setup program.

  Thank you

  Chris

  Connect to the print server with the Ethernet cable to the Ethernet port on the router.

  Press the reset on the print server for 15-20 seconds.

  You could get the printer test page, mentioning the IP address of the print server.

  If this is not the case, the print server and the router to power cycle.

  Open the router setup page and check if you have the IP address of the print server in the DHCP client table.

• Cisco IOS DHCP Server + classless static routes on DHCP clients

  Hi, I tried to find if it is possible to add the ability for static routes to DHCP clients on the Cisco IOS DHCP configuration mode. I'm looking to add a parameters as defined in RFC 3442, like this one, located on the ISC DHCPd server:

  Global settings:

  121 = integer table 8 code option rfc3442-classless-static-routes;

  ms-classless-static-routes option code 249 = integer table 8;

  And for the subnet declaration:

  option rfc3442-classless-static-routes 24, 192, 168, 30, 192, 168, 10, 1;

  option 24 ms-classless-static-routes, 192, 168, 30, 92, 168, 10, 1;

  Is this possible?

  Thank you!

  Vitor

  Yes, the fun part it is to convert it into a format IOS will accept.  You can try:

  IP dhcp pool 0

  option 121 24.192.168.30 ip 192.168.10.1

  option 249 ip 24.192.168.30 92.168.10.1

  If this does not work, change the "intellectual property" for "hex" and each of your decimal byte converted to hexadecimal.

• Client-server applications with problems

  We use appvolumes 2.10

  We are certain to have issues with client-server applications such as launch winscp and subversion.they very well, but they can not connect to servers. The appstacks work fine on own vanilla but does not work on the main image with all the policies and basic applications. When install us it manually on the main image the applications work as expected. Indications on where we can make changes on the primary image for the appstacks works? Thank you

  Lakshman thanks for you the directions. I tried to change the .cfg file last week, but had no luck. It's a known with Appsense AM incompatibility. We have uninstalled Appsense & h and it seems to have solved the problem.

• Consistency API solves all the problems of coherence Client/Server App.

  While working on consistency client/server applications, I hope that only the consistency API would be enough for the part coding mainly for the management of the caches.
  It is necessary to adopt some other APIs such as 'Spring AOP + Annontation' for the management of caches through webservices, pls?
  
  Edited by: online247 July 19, 2011 15:02

  Re: "I hope that only consistency API would be sufficient for the part coding mainly for the management of the caches.

  Yes.

  But hiding a lot more than simple 'management' (i.e. start then get / put.) You may want to use a larger section of the API to make "in place" data processing where he resides in fact (i.e. on the server side) using input processors, etc. etc. Same read/write of data from external sources, that is the basics. Good reading to the top of the dev Guide. What coherence do (some of them not even you force to actually encode anything via the API.)

  Re: "is it necessary to adopt some other APIs such as 'Spring AOP + Annontation' for the management of caches through webservices, pls?

  Well, only not for the 'management' of the caches. You tend to do more monitoring and management via JMX.

  But for 'access' caches...

  If you want a 'web services' interface on your registry caches, it's your call, how to go about it. I had good results with Apache CXF in the past, using the standard Java Web Service Annotations to the drive. The use of the spring and Spring AOP is yours. Consistency do respect, it's just a choice that you make about how you want to achieve the specific requirements of your project.

  See you soon,.

  Steve

• DHCP client enabled on XP x 64 = LAN down.

  XP x 64 wins netowork.
  I have 2 machines with XP SP3 x 64 in a largely 32-bit environment. These machines will take the network. For a long time, I didn't know what was causing the loss of packets on the pings and no LAN or exteranal Web pages to load. I was able to identify the problem by unplugging all Dataport one (we have only about 150 or more). I was able to isolate the problem to a specific machine. I had cloned the machine and put the clone on an another identical hardware configuration. This machine would be the network as well down. Just for posterity, I turn off the NETWORK interface integrated and inserted a PCI NIC, problem still occurred. I was able to come in one long night after everyone had disappeared and that the network was "mysteriously" down again. I knew it was the XP x 64 machine the cause. At this point, I decided to take the other identical machine offline.
  If I physically unplugged the ethernet cable and the network would be back immediately. I did 3 or 4 times. I also tried troubleshooting to identify how service could be the cause of the issue. All services, I have started and stopped only the DHCP Client Service would take the network at startup. It was like a switch. = Network down active DHCP client. Collapsed = network upwards. on several occasions. I've reformatted both machines with xp x 64 but don't want a repeat. Any information you could provide would be appreciated.
     
  We have a server that is running server 2008 x 64 (not a domain controller. Basically just a host for a virtual Server 2003 running Exchange 2003)
  Network configuration: we have 3 physical on the site servers and the other virtual. We also have a VPN to two remote sites with the domain controllers are there. About 50 workstation or so, almost all of the Windows XP 32. just 1 or 2 Win 2 k machines. No Vista or Win7 yet.
  Any idea on why this would be useful.

  Hello the Oregonian,

  Then, when you put a sniffer of packets on the wire so that the XP x 64 boxes have been rising, making that reveal? Good advice on all XP themes, visit the http://www.annoyances.org/exec/forum/winxp

• SDM & easy VPN server problem

  I'm having a problem setting up an easy VPN server using Cisco Security

  Device Manager Version 2. 0a on a router in 1711 with IOS 12.3 (7) XR3.

  I have reset the router to the factory defects since the opening screen of SDM.

  Connect to 10.10.10.1

  User: cisco

  Password: Cisco

  Start SDM for the initial router configuration dialog box.

  Don't use CNS

  On basic configuration screen:

  Hostname set to router

  Domain: test.com

  Synchronize time with local PC

  Change the user name

  New user name: root

  password: xyzzy123

  password: xyzzy1234

  The LAN Interface Setup screen

  IP address set to 10.1.1.1

  Subnet: 255.255.255.0

  Active DHCP server

  Start IP: 10.1.1.50

  End IP: 10.1.1.70

  DNS Configuration screen

  Primary: 45.45.45.45

  Secondary: 45.45.45.46

  Use for DHCP Clients

  WAN Configuration screen

  Ethernet selected without Encapsulation PPOE

  No dynamic (DHCP Client) host name

  Advanced options screen

  Selected for VLAN1 port address translation

  After reading the summary, I chose the FINISH. Asked if dialog box I have

  you want to set up a basic firewall, I selected YES. I left all the

  secure by default items selected. I clicked FINISH. SDM detected that the

  DHCP client on the untrusted external interface and asked if I wanted to

  allow DHCP traffic through the firewall. I selected YES. The configuration

  has been delivered.

  Save the running-config startup-config and reloaded the router.

  Released and renewed my ip address and then reconnected in 1711 from new

  user name and password. SDM restarted.

  Has begun the task of configuration and choose to set up an easy VPN server.

  The opening screen had a command prompt to enable AAA. I launched the selected task

  After that the AAA commands have been delivered to the router.

  I chose the interface FastEthernet0 menu drop-down

  IKE proposals - selected default all the

  Transform set - selected default all the

  Group authorization / policy research - Selected Local only

  Add the user name: User1

  Password: local1

  Encrypt with MD5

  Privilege: 2

  Group permission/User Group Policies

  Add political group: tunnel

  Preshared key: sharedkey

  Selected new address Pool: 10.1.1.80 to 10.1.1.90

  Test after you have configured the selected button.

  Exit this screen, there was a warning SDM on the NAT with ACL rules

  have to be converted into NAT rules with course maps. I clicked YES to let

  SDM convert rules.

  Tests successful Easy VPN Server and client screen displays a warning

  on the "crypto ipsec df - bit clear' needing to be defined." He was not a

  way to put it in SDM and the search function had no success.

  I copied the running-config to the startup-config and tested the router from a

  connect remotely using a different ISP.

  The results:

  The SDM monitor shows the client connection, but the client cannot ping

  any host on the LAN of the router. No one on the LAN can easy ping of VPN client

  Assigned IP of VPN, but they can ping the client using the asigned IP ISP

  address.

  It seems that SDM not correctly configures the 1711 to route of the

  VPN interface to the local network.

  I enclose my 1711 Running Configuration generated by SDM.

  Hello

  I think that the reason why the ping is not successful is that your LAN IP address (connected to the VLAN interface) and the pool of IP addresses assigned to the client are in the same network.

  You can try assigning a pool of IP addresses for VPn clients that is in another subnet (say 10.1.2.80 to 10.1.2.90) and then try to ping?

  You can change the pool by means of configure-> additional tasks-> local swimming pools.

  You can then disconnect the client on the Monitoring page and connect again.

  Kind regards

  Ravikumar

• Debian 5.0 host and Client, network problems

  I have a system Debian 5 (Lenny) as a host for VMware Server 2.0.1 with a configuration ethernet servile (bond0 with Robin balancing).

  This host is the ping requests etc. without problem by any computer in the network and vice versa. This host gets its IP address of a DHCP server and appears very well.

  On this host, I run a virtual client, also Debian 5 (Lenny), with an ethernet in Bridge mode connection.

  This host gets its IP from DHCP Windows without problem and is also listed correct

  The host can ping the client without problems. The client cannot ping the host: ping packets 1 in 10 get through.

  Same story for ping any other computer on the network and vice versa (ping the virtual client from any computer).

  A very small amount of packets through. Can someone help me?

  I'll give you the basic information (see images) for host and virtual client.

  Threesa wrote:

  I changed to mode 5 (transmission of balance) and rebooted, but no progress so far: s

  It was a general indication. If you use a NIC team, no matter whether you use VMware, you use BLT if your switches do not support a protocol group.

  The manual on page 238 describes only for Windows is told by the way.

  .. .and some general tips like this: VMware has not tested and does not support the network adapter teams with

  VMware Server on Linux hosts. »

  Would it because I listed the OS as Debian 4 like Debian 5 was not available in the drop-down list?

  It is a line that wraps a LOT in the newspaper for vmware: cannot find Debian conversion type: vim.vm.GuestOsDescriptor.GuestOsIdentifier

  I do not think because if the problem is related to the link it is not related to the prompt (you can install a Windows client for example who is facing the same problems then).

  I thought back to a NETWORK card to check that your installation works in general. If this is the case, we can try to get the liaison work.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP / vEXPERT 2009

  Published by AWo

• Must regularly restart the DHCP Client - HP Pavilion 500-205 DT - Windows 7

  HP Pavilion 500-205 DT - Windows 7 Home Premium 64 - bit SP1

  Realtek PCIe GBE Family Controller - pilot 7.67.1226.2012

  Bought 3 identical machines for our daycare. Set up the same. All work fine except ONE of them becomes inaccessible periodically (every day more or less) on other computers on our small LAN-to-peer Windows. You can see, but cannot access any shared folder. To access OTHER computers on the local network of it there is NO problem. All 3 machines have the same profile sharing, workgroup, permissions, AV, firewall, all settings. I realized by restarting the computer solved the problem immediately but temporarily. I reduced to restart the DHCP Client service. Do all works well immediately, but temporarily.

  I tried the things:

  Call support HP - not useful at all. It is under warranty.

  IPv6 disabled

  Disabled wireless

  Disabled network card stopcock energy saving

  Definition of recovery CLIENT DHCP on:

  First failure = restarting the Service

  Second failure = restarting the Service

  Subsequent failures = restarting the Service

  Reset Fail Count after = 120

  Restart the Service after = 0

  But again, this is not the case for other machines with the default settings. Nothing works except the Client DHCP service is restarted. Loss of access occurs with or without someone connected or using it. It has happened since its first establishment.

  I don't know if the HP warranty covers the OS loaded at the factory. I don't want to restore the thing and start over. I'm not a Pro, just the guy in the office who did these things, but it seems that the network card may be faulty. I don't know if I can convince a person of first level support phone to have me bring the machine in an approved place.

  Any help greatly appreciated,

  Larry

  HP sends a FedEx box to put the thing in picked it up. I'll mark this resolved thing. Thank you all for your comments!

• Client/Server simple Bluetooth on the same machine

  Hi all

  I have a simple question about Simple Bluetooth Client/Server example. Perhaps the answer is obvious and I'm just a fool, but nothing is written about it in all subjects I've read:

  Simple Bluetooth Server.vi and Simple Bluetooth Client.vi may be running on the same computer?

  Hi Frax,

  the device you want to connect with and the pc must be different, because the communication works with address and I don't think he'll like use the same address for the server and client...

  Problems to use this example?

  It will be useful,

  Let me know!

  FBM

• Error: Failed Application path: C:\Program Files (x 86) \Trend Micro\Client Server Security Agent\HostedAgent\svcGenericHost.exe

  original title: genric hosted agent services

  Description

  The failing Application path: C:\Program Files (x 86) \Trend Micro\Client Server Security Agent\HostedAgent\svcGenericHost.exe

  Signature of the problem

  Problem event name: APPCRASH

  Application name: svcGenericHost.exe

  Application version: 3.5.0.1163

  Application timestamp: 4d9d3841

  Fault Module name: StackHash_0a9e

  Fault Module Version: 0.0.0.0

  Fault Module Timestamp: 00000000

  Exception code: c0000005

  Exception offset: 74676c9c

  OS version: 6.1.7601.2.1.0.768.3

  Locale ID: 1033

  Additional information 1: 0a9e

  More information 2: 0a9e372d3b4ad19135b953a78882e789

  Additional information 3: 0a9e

  Additional information 4: 0a9e372d3b4ad19135b953a78882e789

  Additional information about the problem

  Bucket ID: 2507689456

  Maybe you shouod check with Trendmicro support.

  http://eSupport.trendmicro.com/en-us/default.aspx

• Svchost and dhcp client slows windows xp

  I've recently updated the image into my netgear router. The device is connected via a powernet connection.
  But since the upgrade and also a little before the upgrade, the svchost in windows xp that runs the thread of the dhcp client has been slowing all processes within windows xp sp3.
  It has now got to the point that I have to wait more than 2 hours before I can get on the internet with any real effect. It costs money to my company and I am sure that Mr. Gates would be more upset if his employees only had 1/2 hour of work time each day due to an unusable operating system.
  I don't have the original image file to down-grade of the router. Can anyone suggest a fix for this problem?

  I know that this problem has been reported for many years through different websites and microsoft have still not managed to solve this problem.

  Hi tmd63,

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

  Method 2: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  In Windows network connection issues

  Method 3: Update the latest drivers for network.

  How to manage devices in Windows XP

• Cannot get the DHCP client service to start automatically

  I work on a computer that has been recently infected with a fake AV protection virus.  The user has removed the virus using Microsoft Essentials and Malwarebytes.  Subsequently, they were unable to connect to a network with wired network cards or wireless.

  The afd.sys file has been deleted and couldn't start the DHCP client.  As soon as I restored the AFD, I was able to manually start the DHCP client.  At this point, I was able to connect to the network and get on the internet.

  The problem is that I restarted the computer and saved in Windows, the DHCP client is not automatically start as it should by the setting.  I can still go and start it manually, but it does not start by itself.

  I tried to use Winsock fix, the different netsh commands, / flushdns and enough & renew, tdsskiller and a number other programs I have come across.

  Computer is running Windows XP Service Pack 3

  Microsoft Essentials, Malwarebyes, Superantispyware and CCleaner are all installed.

  Any ideas on how to get this to start running automatically without having to do a reinstall of Windows XP?

  Thank you.

  an error saying there is no hard drive installed.

  This may mean that you have a SATA drive.  If so, you have to activate something like "legacy mode" in the BIOS before you can use the XP CD to do a reinstall (unless you have a floppy drive to add SATA drivers or integrate a CD with SATA drivers).

• WRT54G2 DHCP Client Table empty.

  OK this thing is 4 days and worked fine until today. Wireless can connect to it. My DHCP client table is empty (does not see the same wired connections). I tried the firmware update, reset to factory settings I even unplugged it DST foer. No luck.

  Note: this was bought to replace a month 8 old WRT160N which oddly would not release someone from the DHCP client table and would regularly not people to reconnect because he thought that it was already connected. That the only solution was to go inside and remove them manually.

  I don't know what you guys done different with this generation, but you should have stayed with your old G

  Sorry I never posted back, but here is the solution.

  It worked only for the WRT54G2 and not for the WRT160N problem (Im sure this is a hardware problem).

  In any case apparently AVG default firewall (now) blocks all network discovery when it is enabled in your operating system. How and why it affected the client DHCP table i havnt yet understood.

  Solution: If your AVG version help complete (not free) goto Tools/settings system//(whatever profile your using either Standalone or Small home or office) Firewall service. Now scroll CPP of Windows service and to allow for the change. Viola everything works now. Went and did it on all my computers on the netwrk with full AVG and it works now.

• What is a DHCP client address and what is an ISP?

  Try to connect Tivo w / a wireless connector for my computer instead of using the phone line. TiVo's request for a DHCP client address and Pack International customer

  Hello

  The DHCP Dynamic Host Configuration Protocol () is a protocol for network configuration for hosts on networks IP (Internet Protocol). Computers that are connected to IP networks must be configured before it can communicate with other hosts. The essential information needed are an IP address and a default route and the routing prefix. DHCP eliminates the manual task by a network administrator. It offers a central database of devices that are connected to the network and eliminates duplicate resource assignments.
  An ISP (ISP) is an organization that provides access to the Internet.

  See the following link:
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233

  Note: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry