Debian 5.0 host and Client, network problems

Similar Questions

• Vista "Local access only" and "Unidentified network" problem

  Hi recently my Windows Vista Home Premium - 32-bit has had problems with the internet.

  It was only said 'Local' next to the 'access' and said "Unidentified network" and used to connect me on the internet.

  This problem occurs when you try to connect through an Ethernet cable to the Modem and the router and also while wireless.

  I know that this is not the fault of my Modem/Router, because my laptop says this when I try to connect about internet anybodies.

  Ive spent a good 3 days on this problem, looking for every website I could find searching for answers. NONE of them have worked :(

  Ive done everything except Microsoft and their paying a call answer...

  So if someone can help me, please and id love for it :)

  Also I know people will ask ipconfig/all, but I'll wait for a response and download what the person asking. Thank you.

  I will not need now, I used a program called "Connectify" on my windows 7 laptop. (connectify is a program that acts as a hotspot access point)

  Somehow I was able to connect my Windows Vista computer to the internet via Connectify and I ran all the updates on my laptop with Windows Update, now I am able to connect to my router and modem without any problem.

  Hope that if anyone else has this problem, they can also use Connectify to Windows 7 computers and difficulty there problems internet as I :)

  DjKilla ICE

• How to remove file Hello and solve network problems?

  whenever I turn on my pc, I have to wait 1 minute then I must remove the Ethernet cable and then put back again to the internet at work, I think it's because Hello, if it is can someone please, if it's not, can someone please tell me what they think it is. Thank you very much.  :)

  Hello is one of the 6 programs that are installed automatically when you install iTunes.  I have not heard of Bonjour causing the problem you describe (but I have not studied that so it may actually be a common problem with it).  You can uninstall Hello from the control panel > uninstall a program in the same way that you would like to uninstall any program - but who can create other problems with Apple devices if you have one.  Another alternative would be to disable it temporarily by clicking on start > all programs > administrative tools > Configuration system and then go to the Services tab and remove the check mark next to Hello and restart your computer to see if you still have the problem.  You re-enable Hello in the system similar to the way Configuration which you the disabled.

• Public static IP - host and Client

  Sorry if this is bad for this community, but I work with my first installation of vSphere and am a bit new to server virtualization.

  I have my server ESXi 4.1, has just created my first VM on it and began to create the network configuration. My main issue right now - should I I put in place of the static for all IP that I can? For example, I have 4 network adapters on the server that I attributed as follows: 2 for management and iSCSI and 2 for the network of the VM. Who should produce 4 static + static IP for each virtual computer addresses?

  Thanks for your help!

  Hello

  You assign no IP NIC but vmkernel portgroup as iSCSI, vMotion, the service console, FT

  For mgmt - static

  for iSCSI - static

  for VM - you will set up IP on guesOS not on the level of ESX VM

  See you soon
  Artur
  

  Please, do not forget the points of call of the "useful" or "correct" answers

• Network down frequently on a virtual machine after the upgrade of computers host and vmware to win 10

  Dear all,

  A week ago, I upgraded both my two machines VMWare Win 7 to win 10, as well as the host operating system. also from 7 to 10.

  Now once every 1 or 2 days, one or both the two vmwares aura an esclamation mark on the network status icon in the lower right corner and West no connection.

  The host operating system is NOT having any problems with the network.

  The solution is to disable and reactive the adapter to virtual machines, or repair of running Network Diagnostics where she'll tell me that it s has reinstated the connection to the bridge. But obviously I´d prefer the VM´s to be on the internet 24/7 without my intervention.

  I have another computer on the same router on which I did the same thing, but with this I m not having these problems. A different and not connected equipment via the VPN running on the host OS, which is the case with the machine that s had questions.

  But even once, the host operating system is not having issues, the two VM´s aren´t always the two to have this problem, and this never happened when he was all Win 7.

  I ve disabled some nights windows defender analysis and TCP/IP V6, but neither helped.

  Want to see some of the information from the last network diagnostics / repair or some log file, or you already know what would be the solution to my problem?

  Thanks in advance!

  Best regards

  Jazzl

  Well, I thought that a vm was having this problem a lot more often than the other, so I looked for error messages in windows journal, showing that the network problem - have to with DHCP btw - always spent 2 minutes after an event regarding slui.exe, not found on the other machine.

  What I also noticed was that the problematic vm had lost its activation of windows with the upgrade to win 10 (win 10 has limits to how much the same license can be run as virtual machines), is is not the case for the more successful one.

  Then I copied the good machine, which contains the same as the other, changed mac and uuid and now it s showing that enabled, no problem so far.

• Host of migration on 2 no and 2 network vMotion

  Hello

  I'm trying to migrate virtual machines between the two groups.  I use a host on the new cluster as the go between.  This host is connected to two no and two networks of vMotion.

  I would say that I can't have the two vMotion active network at the same time.  So I uncheck the checkbox vMotion IDE oucederomsurlesecondport a vMotion vmk and allowing it on the other hand.  But I find that I have to reboot the host to get to ping or vMotion to the bottom of the other network for vMotion.

  It seems that this is not the second connection.  If I consult the routing table, it is empty for the second connection.

  It seems that I just need to force her to arp on the second connection.  Or somehow for vMotion service restart.

  Any ideas?

  Thank you

  Mike G.

  The problem turned out the vMotion subnet get pinned to a vmk / uplink that was not yet active.  I discovered using esxcfg-Highway - l

  So here's a ping on the failure of network vMotion.

  ~ # vmkping 333.444.1.65

  PING 333.444.1.65 (333.444.1.65): 56 data bytes

  -333.444.1.65 - ping statistics

  3 packets transmitted, 0 packets received, 100% packet loss

  Here's the arp table.  He is aware of the subnet, but it's somehow pinned to the layer of VMware to vmk6.  vmk6 is vMotion on fabric B, which is currently not working due to the non-vmware of the reasons.

  ~ # esxcfg - road - l

  VMkernel itineraries:

  Interface of network gateway subnet mask

  777.444.124.0 255.255.255.0 subnet local vmk1

  777.444.125.0 255.255.255.0 subnet local vmk3

  333.444.1.0 255.255.255.0 subnet local vmk6

  555.888.128.0 255.255.255.0 subnet local vmk4

  555.888.158.0 255.255.255.0 subnet local vmk0

  by default 0.0.0.0 555.888.158.1 vmk0

  Here are the arp table after I deleted vmk6 via vCenter.  333.444.1.0 is now pinned to vmk5.  Or deactivation of vMotion, dropping the uplink or a reboot would turn the road to vmk5.  Only deleting vmk6 fix it.  vmk5 is vMotion on A fabric, that works.

  ~ # esxcfg - road - l

  VMkernel itineraries:

  Interface of network gateway subnet mask

  777.444.124.0 255.255.255.0 subnet local vmk1

  777.444.125.0 255.255.255.0 subnet local vmk3

  333.444.1.0 255.255.255.0 subnet local vmk5

  555.888.128.0 255.255.255.0 subnet local vmk4

  555.888.158.0 255.255.255.0 subnet local vmk0

  by default 0.0.0.0 555.888.158.1 vmk0

  Here's the ping works once vmk6 has disappeared.

  ~ # vmkping 333.444.1.65

  PING 333.444.1.65 (333.444.1.65): 56 data bytes

  64 bytes from 333.444.1.65: icmp_seq = 0 ttl = 64 time = ms 0,346

  64 bytes from 333.444.1.65: icmp_seq = 1 ttl = 64 time = 0,121 ms

  64 bytes from 333.444.1.65: icmp_seq = 2 ttl = 64 time = 0.146 ms

• Network problem between the host computers

  I am in the process of upgrading all my ESXi hosts and I came across a strange problem that I didn't know.  I have 2 guests (two ESXi) and I have a few VM I can't ping when I migrate from one to the other.  This virtual switch has 30 virtual machines running on it and I have two that will not work on a single host.  I run a constant ping and as soon as I migrate to a host I lose my connection ping.  All other virtual machines are still running and very well.  I'm quite puzzled why.  Someone has an idea?  Thank you

  Host2 - ESXi - the virtual machine in question work on this one

  Host4 - ESXi - the virtual machine in question do not work on the work of this one, but all the other fine vm.

  Remove the network adapters on the operating system. UN install VMware tools. Remove the network card settings of the virtual machine. Restart the operating system. Reinstall the VMware tools. Add network adapters on the virtual machine. New analysis of the material changes. Re add parameters, etc.

• Configure the host and the VM on two separate wireless networks

  Hello community, I was a browser for a long time, but this will be my first post.

  I would like to begin by saying that I have always found the answer I was looking for by browsing these forums and that I browsed discussions thereon and consulted the chapters regarding virtual networks in the manual workstation 7.1, but at this stage were still unable to solve my problem.

  The scenario:

  I'm a small business working in a House (upstairs) / hookah lounge (bottom). We recently had a second internet connection (WORK), Internet home of my family (HOME), to provide our customers with a free wi - fi. I would use the connection of WORK (during our hours of downtime) in a Ubuntu VM for folding and seeding of torrents. I want to put this far on a network traffic will not affect the other.

  The network:

  SE host: Windows 7 Pro 64-bit

  (Host) NIC: Intel PRO/Wireless 3945ABG (Mini PCI)

  VM: Ubuntu 10.04 on VMWare Workstation 7.0.0 build-203739

  NIC (VM): Alfa awus036h (USB)

  
  

  The current configuration:

  Network connection is made, the State of replication physical physical network is unchecked.

  The Alfa is connected to the virtual machine and is no longer present on the list of the network adapters in Windows.

  It seems that I have to manually disable the "auto eth 1" interface or the virtual machine using the internet connection in host rather than the network of your choice that the Alfa connects to in VMWorkstation. The speed of the internet with eth auto 1 is connected is quick and consistent, but using it defeats the purpose. Strangely, when I go to network connections, under the "last use" for "eth 1 auto ' it is said 'never '.

  When "eth 1 car" is disconnected, it seems that the virtual machine uses the network wireless connected to the Alfa. But the internet speed is very slow and inconsistent. On downloads, the speed varies considerably; Also, it remains at 0 kb/s for a while before going to 80 KB/s, then works his way down to 0 kb/s again.

  Possible solutions:

  1. it's a driver problem for the Alfa inside the VM environment all this time?

  2 just misunderstood how to set up this kind of virtual network?

  3 is it possible to get the desired configuration by filling the WORK and VMnet0/1/8?

  * Note: Only VMnet1 and VMnet8 appear on the Windows network connections, however isn't VMnet0 bridged one responsible for networking?

  4. upgrade to the current version of the desktop would be useful?

  5. do this problem originally because of some settings on the router?

  * Note: The AP is close enough to provide a signal strength of 85-90%

  Sorry to be so talkative, I just wanted to be as clear as possible because I'm still a beginner to learn more about virtualization.

  Thank you in advance, as always, your help is greatly appreciated.

  First of all, I must say that when I did this last response, I've been on my Mac and I thought the configuration of a host of Windows XP however outside the nomenclature of the names of the host network settings dialog box the rest stands as it is on a host Windows 7 as described below, including a picture as an attachment.

  On a Windows 7 x 64 host with two network adapters, each on a different subnet and VMware Workstation 7.1.3 installed with the editor of virtual computer network configured for VMnet0 and VMnet2 jumpered separately to one of the host of NIC and I have not changed the settings for Windows 7 host NIC-1 and have network/Internet connectivity to the host of this NETWORK adapter as shown in the picture of Google in Internet Explorer on the host computer.  In VMware Workstation 7.1.3 I have a Linux Guest configured to use VMnet2, which is filled in the settings and the Windows 7 host NIC-2 have all with the exception of VMware Bridge Protocol unchecked and have network/Internet connectivity in the guest as indicated by Google in a browser.

  From the perspective of connectivity network between the host and the guest by NIC - 2 on the host computer when all with the exception of VMware Bridge Protocol unchecked there is no connectivity between the two on this subnet because there are no protocol at stake to allow the conversation to take place.

  So theoretically and in practice what I said previously, but didn't were not expressly with a Windows 7 host in mind, nevertheless what I said is true and accurate, as evidenced by world real test/use by what I said and with the image attached herein.

  FWIW Windows 7 has been configured with the default settings and the only changes to the host's network were those made during the installation of VMware Workstation 7.1.3 so with the configuration I discussed with the attached picture, there is no reason why the host and the guest cannot be on different physical networks and each network/Internet connectivity based on the information I have provided and they be isolated from each other by being on separate physical networks.

  That said, even if they can be isolated by being on separate physical networks can still can connectivity between the 2 through VMware shared folders it it turned on and of course & slide and other services so if absolute isolation is necessary to the point where it can be, and the guest still operating system run on a Virtual Machine in the host you would need to disable the Backdoor for VMware Tools cannot provide shared folders on VMware, & glide and other services.  So if you need this isolation level let me know and I will provide additional information to complete it.

• "Unable to connect to the MKS: unable to connect to the host [servernamehere] failed on vSphere 4.0 and client.

  Anyone have this problem?  I loaded vSphere 4.0 host ESX 3.5 and everything seems to work very well yesterday, after sleep more testings and this error arose:

  "Unable to connect to the MKS: unable to connect to the host failed on vSphere 4.0 and client.

  After a google search, I could it is resolved by placing the DNS entries on the client machine c:\windows\system32\drivers\etc\hosts file point to my ESX host name and domain name FULL name runs and it worked fine.  I'm curious to know why this went well?

  What is MKS mean in this case?  Server key from Microsoft or the key management server?

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Kind regards

  Stefan Nguyen

  VMware vExpert 2009

  iGeek Systems Inc.

  VMware, Citrix, Microsoft Consultant

  When you click on the console of a virtual machine, the server that hosts the vm responds back with its host name for your client to connect to.  Thus, the MKS console could not be connected to, and you could not see the virtual machine console, until you updated name resolution.  Given that the ESX host is back with a name, the customer could not resolve the name, if your client could not connect to the virtual computer mouse, keyboard, screen.  Hope that makes more sense.

  -KjB

  VMware vExpert

• host and network bridge

  Is someone can you please tell me what is the right way to create a virtual machine with the host only networking and a static IP address?

  What should be the range of IP addresses for the host only one virtual computer?

  Thank you.

  fernandoch wrote:

  OK well with that. But how do I access the virtual machine with an IP 192.168.1.101 host if it uses a briged network and I can not access the same virtual machine (with IP address

  192.168.1.101) so it uses only network host?

  The subnet of the host is only 192.168.50.0

  Because it seems that you use wrong IP address in your comments.

  Each IP network needs its own subnet address. This means that the physical and virtual network who need different IP subnet addresses. This is the case with your installation and that's right.

  If you move the mode prompt "bridged" with IP subnet address 192.168.1.0/24 to 192.168.50.0/24 the guest needs an IP address in this range. Either set it to DHCP and if you have not changed the default settings in VMware it will receive a correct IP address automatically configuration or set the IP address manually, for example 192.168.50.10 (and if this address is still available). Furthermore, if you set the DHCP client and if you have a DHCP server on the local network physical prompt always gets the right to installation when you mofve it from one network to the other.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP / vEXPERT 2009

• Host and guest of the machines on different physical networks

  Hello everyone.  I would wise advice from the forum, about a particular environment, I am trying to set up.

  I have VMware Server 2 installed on my XP laptop, which is connected to a DSL modem via a NIC edge portable said has also a PCMCIA NETWORK card installed in it.

  I would like to take a virtual XP workstation and connect to a modem cable via the PCMCIA NIC for test connection hosts and guests safe through the public internet.  For this exercise, I need two machines to be completely separate and therefore have no way to reach or in interaction with each other anyway, except through the extended link.

  What follows is a list of what I've done so far.  I would like to know if there is anything I missed.  Perhaps more measures must be taken that I'm not aware of.

  Thanks in advance for your collective time.

  (1) disabled all services associated with the PCMCIA NIC on the host computer, including TCP/IP, except the VMware Bridge Protocol.

  2) welded by the mentioned back PCMCIA NIC to VMnet2 via VMware Virtual Network Editor.

  (3) excluded the NETWORK PCMCIA card automatic connection via the virtual network Editor.

  (4) set up the virtual ethernet device of the instance XP comments use the custom VMnet2 network.

  (5) set the property 'NetworkAddress' of the network connection in the case of XP from comments to the MAC address of the PCMCIA NIC by step seven of the next mission - http://communities.vmware.com/message/378576;jsessionid=034FC6E865C0DB28AD269D7445F2AD0D

  PS - How could these measures differ for a guest computer to Linux (openSUSE 11), especially step 5 in my list above?

  Welcome to the forums!

  IMHO, I think you have done all that was required. I don't know why your step 5 is necessary or if it will be same cause problem. "Bridged" means that the customer acts as its own instance on the network, which includes a discreet addresses MAC and IP, from my point of view. Affecting the MAC guest host MAC is not necessary for the connection of standard bridge, so why if it is necessary here? In addition, you can set any MAC address that you like for a VMware guest. There are restrictions, once again setting the host MAC address in the guest can cause problems.

  You can find the VMware documentation on how to do it here: Page 240, http://www.vmware.com/pdf/vmserver2.pdf

  There is also something on definition of MAC addresses: Page 234

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP/vExpert 2009

  Published by AWo

• Satellite P30 - need a CD-resuscitator and network problem

  Please if you can help out and drive!
  Problems with the computer, in the disconnected himself from the network?

  Hello

  To be honest I n don't know what you want. You write in the title on a CD reanimator, but you have problems with the network
  It is not very clear.

  In addition, you should give us more information on your OS and a description of the exact problem.
  You have this problem on the LAN or WLAN?

  However, try to update the drivers. You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Welcome them

• Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem? ___

  Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem?
  I have also recently set up a wireless network.

  Hello

  Try this 1st to see if it helps, and it should:

  Description of the Patch registration cleanup tool
  http://support.Microsoft.com/kb/976220/

  ------------------------------------------------------

  If necessary :

  Try this - Panel - Windows Updates - on every update that will not be installed - click on the important updates
  or the update itself - double click a view more information (or click top then discovers on the right)

  Those who will take you to a page where you can download the update.

  Or go here and the KBxxxxxx number to download it.

  Download Center - mount the KBxxxxxx.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  Download - SAVE - go to where you put them - click on - RUN AS ADMIN

  Then you can right click on the update in the updates Windows and HIDE.

  If you get an error Installer install this version:

  Windows install 4.5 Redistributable
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  ----------------------------------------------------

  Then run this:

  How to reset the Windows Update components? -a Mr Fixit
  http://support.Microsoft.com/kb/971058

  Description of the system for Windows Vista, Windows Server 2008, update tool and
  for Windows 7
  http://support.Microsoft.com/kb/947821

  ------------------------------------------------------------
  Because these are all Office updates you might get more information if necessary in the Agency of those groups that
  may have experienced the same problem.

  Office newsgroups
  http://www.Microsoft.com/Office/Community/en-us/FlyoutOverview.mspx

  Microsoft.public.office.misc discussions
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Office.misc&cat=en_us_01cb749f-c998-4762-8099-df71793c11c7&lang=en&CR=us

  ------------------------------------------------------------

  If necessary you can incident free get reports however the above should take care of it for you.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps and happy holidays!

  Rob - bicycle - Mark Twain said it is good.

• "Receive the error message" Microsoft (R) HTML Application host has encountered a problem and needs to close, etc. "when you access user accounts

  Original title: I can't access the accounts of users (XP).

  I can not access (XP) user accounts.  I get the message: "Microsoft (R) HTML Application host has encountered a problem and needs to close etc.."  The APPname is mshta.exe. I have this msg when I click on anything in the user accounts.

  1. What is the problem?
  2. what should I do to fix this?

  Hello Eric_984,

  Thank you for the question!

  It is disheartening to know that have problems you with user accounts. "As I understand it, you get an error message" Microsoft (R) HTML Application host has encountered a problem and needs to close etc. "when you access user accounts.

  I need to ask you a question to help you best.

  Were there any changes (hardware or software) to the computer before the show?

  Perform the steps in the link and check.

  Error message when you try to open the item user accounts in Control Panel on a Windows XP-based computer: "Microsoft HTML Application host has encountered a problem and needs to close."

  Answer to us if you are having problems with user accounts or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• Each time after clicking the icon of user account on windows xp to change a password is crashes with this error message: Microsoft (R) HTML Application host has encountered a problem and needs to close.

  Each time after clicking the icon of user account on windows xp to change a password is crashes with this error message: Microsoft (R) HTML Application host has encountered a problem and needs to close.

  There is a Microsoft Knowledge base article which sets up a few steps to perform in the computer in order to solve the problem you are experiencing, read the article that you find on the link I am mentioning below and see if it helps the measures mentioned:

  http://support.Microsoft.com/kb/919751