DIAGONISTIC HARDWARE TOOL

Similar Questions

• How to stop "FOUND NEW HARDWARE tool"

  Whenever I start up I get the message "FOUND NEW HARDWARE TOOL' up to four 4 times before so I can continue."  How in the heck to I get rid of this.  It is also irritating as my HP printer messages all the time!  LEA

  Hi LEA J.HIGGINS,.

  ·          Did you the latest changes on the computer?

  See the below Microsoft article and try the steps mentioned, check if it helps.

  The new hardware wizard may detect the printer device after every restart of the computer

  http://support.Microsoft.com/kb/298370

  If the previous step fails, then check in the Device Manager to see if a device does not work or pilot device tries to install at the start.

  How to troubleshoot unknown devices listed in Device Manager in Windows XP

  http://support.Microsoft.com/kb/314464

• tools and hardware upgrades through the update after the upgrade Manager

  If I run a base line to upgrade tools and equipment of vmware, then choose restore, is a clever enough Update Manager to make tools first and then perform the upgrade of hardware vm? I have a few machines I moved from 4.1 to 5.1 and the two operations must be made. I don't know if I have to do both together or separately.

  This logic is incorporated in the Update Manager if you use grouping Baseline: basically, create a group with the material and baselines Tools, join group reference VM (s) that interest you and to fix. Otherwise, you can make sanitation through autonomous base lines - in this case, you would need address first, then hardware tools.

• No more VMotion after upgrading hardware VM

  Hello

  We have improved our servers successfully VMWare to ESX4.0 build 175625 (Group 1) and ESX4i build 181792 (Group 2). Right now we are upgrading all our VM to VMware and virtual machine hardware tools.

  Everything works well and more VM becomes green in Update Manager indicating the VM is perfectly updated and a fine, BUT... all the VM which is currently being upgraded cannot be VMotioned to anoter host! When you try to migrate a virtual computer to another host, he says:

  Host CPU is not compatible with the requirements of the virtual machine to CPUID level 0 x 1 register "ecx":

  Bits of the host: 0000:0000:0000:1000:0010:0010:0000:0001

  Required: 1000:0000:0000:100 x: xxxx0:0x1x:xxx0:x 001

  Why is it all of a sudden? I hope that I don't have to change all the masks of the host for all my virtual machines now?

  Take a look at this article

  http://KB.VMware.com/kb/1011294

• MacBook Pro delivers after water damage

  Hello.

  I have the model: A1278 I do not know what operating system is installed

  The laptop in question got wet and is now dry.

  The problem starts when I turn on the system, it normally turns... (but slower)  It asks me to put my password. When I enter it, it says it is incorrect and asks me if I want to reset it using my apple ID, when I press on it the computer crashes.

  I tried to insert a USB stick with version OSX 10 but when I press and hold C or D I get the following error:

  

  Since to play I can not even get it back to the password screen. It just constantly restarts all by showing a blinking globe.

  I also tried ALT - D with an ethernet cable is plugged.

  All data are saved.

  I can't get the hardware tool to work.

  Clues about the error message given? I tried to remove the two RAM sticks.

  Any help would be appreciated. Thank you.

  Your best option is an appointment at an Apple store for a FREE genius bar.  Wait for a repair quote are very high.

  Ciao.

• iMac 8.1 stuck on the apple logo

  Model: iMac8, 1

  2.66 GHz Intel Core 2 Duo

  At 2BG memory when the problem started

  Mountain Lion 10.8.5

  Is in trouble with occasional frosts. Would be closed and it should restart very well. About 2 weeks ago, the computer froze. I shut down the computer and restarted. The apple logo came with the spinning wheel, and then just the apple logo.

  I can start safe mode. Tried resetting the PRAM, reset of SCM. Tried to start with all peripherals except keyboard and mouse disconnected. Use the command R to start the computer and went into the disc utilities. Disc checked and it said disc looks OK. Verified permissions. Mistakes came for iTunes more a warning which was not repairable. Fixed permissions. None of these permits to start properly.

  Parle talked anyone computer repair who suggested to unplug the computer, hold the power button while up to one minute, plug the computer back in and pressing the Start button. It came in fine. A few days letter that the computer froze and I had to stop it. You press the Start button, got the spinning wheel, so only the apple logo and apple logo. Start the computer by pressing command + R and reinstalled Mountain Lion. Installation once it stuck at the apple logo again. Active disk. Drive seems to be OK. Permission verified. Permission with iTunes but issues no warning this time. Repaired permissions. Nada.

  Inserted the installation disk, turned on the computer while holding D key. A ran Apple Hardware tools (tests of short or long). This error message came up twice with different numbers of rpm: 4MOT/1/40000003: drive HARD-110. I know that it's the hard drive fan. Computer repair man came out. Thought problem may be because I only had 2 GB of memory and ran only to open the Lion of mountain with several programs. Upgrade to 4 GB memory, which is recognized by the computer. But the computer still does not start correctly. Tried the Single Mode and run/sbin/fsck - fy. Said it seemed OK, but changed the volume. Ran he says once again and everything seemed OK. Still will not start.

  When I start in the disc, part of the grey background Utilities is missing. If you move the cursor on the screen, the gray background fills.

  Also, when I try from normally I get startup chime, the apple logo and the spinning wheel. After that make a spin the wheel stops, there is sort of a Flash, then the wheel goes and remains the apple logo. I can hear the computer tries to do something, then the arrow cursor appears and can be moved around the screen. It's like that.

  Also installed Mountain Lion on a USB key, it made the startup disk and tried to start the computer normally. Still will not start.

  Any ideas or suggestions for what could be wrong or other things to try?

  1. the present proceedings is a diagnostic test. It doesn't change anything for the better or worse and therefore, by itself, will not solve the problem. But with the help of the results of the tests, the solution may take a few minutes, instead of hours or days.

  The test works on OS X 10.8 ("Mountain Lion") and later versions. I do not recommend running it on older versions of Mac OS X. It will do no harm, but it will not do not much good.

  Do not be put off by the complexity of these instructions. The process is much less complicated than the description. You make the tasks more complicated with the computer all the time.

  2. If you do not already have a current backup, please back up all the data before doing anything else. The backup is needed on the general principle, not because of what anyone in the test procedure. Backup is always a must, and when you encounter any kind of problems with the computer, you can be more than the usual loss of data, if you follow these instructions or risk not.

  There are ways to back up a computer that is not fully functional. Ask if you need advice.

  3 here is instructions to run a UNIX shell script, a type of program. As I wrote above, it doesn't change anything. It does not send or receive data over the network. There is no to generate a report on the State of the computer human readable. This report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents for me or someone else.

  You should ask yourself if you can believe me, and if it is safe to run a program at the request of a foreign national. In general, no, he's not sure, and I encourage it.

  In this case, however, there are ways for you to decide if the program is safe without having to trust me. First of all, you can read it. Unlike an application that download you and click to start, it is transparent, anyone familiar with the code can check what it does.

  You may not be able to understand the script yourself. But variations of it have been posted on this site several times over a period of years. One of the million registered users to have read the script and set off the alarm if it was dangerous. Then I wouldn't be here now, and you would not be reading this message. See, e.g., this discussion.

  However, if you cannot satisfy yourself that these instructions are safe, do not follow them. Ask other solutions.

  4. here is a general summary of what you need to do, if you decide to go forward:

  ☞ Copy text from a particular web page (not this one) to the Clipboard.

  ☞ Paste into the window to another application.

  ☞ Wait for the test to run. It usually takes a few minutes.

  ☞ Stick the results, which will be copied automatically, in a response on this page.

  These are not specific instructions; just a glimpse. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait and paste it again. You don't need to copy a second time.

  5. try to test in conditions that replicate the problem, to the extent possible. For example, if the computer is slow intermittently, run the test during a downturn.

  You may have started up in safe mode. If the system is now in safe mode and works pretty well in normal mode to test run, restart as usual before running it. If you can test only in safe mode, this.

  6. If you have more than one user and a user is affected by the problem, and the user is not an administrator, and then run the test twice: once under the affected user and one administrator. The results can be different. The user that is created automatically on a new computer, when you start it for the first time is an administrator. If you are unable to log in as an administrator, verify that the user concerned. More personal Mac have only one user, and in this case this section does not apply. Don't log in as root.

  7 load the linked web page (the site "Pastebin.") Press the combination of keys command + A to select all the text, then copy it to the Clipboard by pressing command-C.

  8. start the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name ("Terminal") in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing Command + V, then press return. The text that you pasted should disappear immediately.

  9. If you logged in as an administrator, you will be prompted for your login password. Nothing displayed when you type. You won't see the usual points instead of the characters typed. Make sure that caps lock is turned off. Type carefully, and then press return. You can get a warning to be careful. If you make three unsuccessful attempts to enter the password, the test is still running, but it will produce less information. If you do not know the password, or if you prefer not to enter, just press back three times at the password prompt. Yet once again, the script will run.

  If the test takes much longer that usual to run because the computer is very slow, you can be prompted for your password a second time. The permission you grant by entering it will expire automatically after five minutes.

  If you are not logged as an administrator, you will be prompted for a password. The test will run. It just will not do anything that requires administrator privileges.

  10. the test may take a few minutes to run, depending on the number of files you have and the speed of the computer. A computer that is abnormally slow may take more time to run the test. During execution, a series of lines is displayed in the Terminal window like this:

      Test started

          Part 1 of 4 done at: … sec        …        Part 4 of 4 done at: … sec

      The test results are on the Clipboard.

      Please close this window.

  The intervals between the parties will not be exactly the same, but they give an approximate indication of progress.

  Wait for the final message "Please close this window" appear - again, usually within a few minutes. If you don't see this message in about 30 minutes, the test probably won't be completed within a reasonable time. In this case, press the Ctrl + C key combination or the point command to stop it. Then go to the next step. You will have incomplete results, but still something.

  In order to get results, the test should be allowed to perform or be stopped manually as shown above. If you close the window of the Terminal, while the test is still running, the partial results will not be saved.

  11. when the test is completed, or if you manually stopped, leaving the Terminal. The results have been saved to the Clipboard automatically. They do not appear in the Terminal window. Please do not copy from there. All you have to do is start a response to this comment and then paste it again by pressing Command-V.

  At the top of the results, there will be a line that begins with the words «Start time.» If you do not see that, but rather to see a mass of gibberish, you wait for the message "close this window". Please wait and try again.

  If personal information, such as your name or e-mail address, appear in the results, make anonymous before posting. Usually it will be not necessary.

  12. in the validation of the results, you see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the software which manages this website. Thanks for posting the results of the tests on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

  13. When you are finished with the test, it is gone. There is nothing to uninstall or clean.

  14. This is a public forum and others can give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but all that you can not be. For others who choose to run it, I do not recommend that you view the results of test on this Web site unless I ask.

  15. the related UNIX shell script is a notice of copyright. ASC readers can copy for their personal use. The whole nor any part can be redistributed.

• HP dv6000 with Hp lp2475w.

  Hello... I know very little computers so any simple advice would be apreciated.

  I have a HP Pavilion dv600 (vista 32 bit). It has a mounted Nvidia geforce Go 6150 graphics card.

  I use mostly this laptop with photoshop to edit photos. Because of the limitations of the screen of the laptop I buy a HP LP2475w monitor to use as an external display. This screen has a native resolution of 1920 x 1200. My spec graphics card ' says that it will support monitors up to this res.

  We know if this material match will work OK? All the problems?

  My NVIDIA Control Panel does not have a facility to change the screen resolution so I would normally change it in Control Panel, but listed here max res is 1280 x 800. Is it because it's the res max for the laptop screen? Does then change it to a maximum of 1920 x 1200, after I installed the new driver monitor and selected which monitor?

  Because the graphics card uses the memory of laptops I need to change the settings to allow him to use more?

  If so how would I do that?

  Sorry... a few questions in here!

  Thanks for any help

  It should work perfectly. There is no way to change the video memory and no need to do so. The pilot video and material pull in as much memory as necessary to support that the work you do. Yes the only resolution that you have now is 1280 x 800, because that's the max of the laptop screen resolution. Once you plug in the external monitor, another screen will appear and you can configure in nVidia control panel. See if it doesn't just without load the driver for the monitor and if not, then load the monitor driver that comes with the monitor. You only need to run screens dishes (including your built in the laptop screen) to the default resolution, which is also the max.

  You can consider to extend the Windows desktop on the external screen, but you can also mirror the current desktop on the external monitor. My wife is a professional photographer who lives his life's work in Photoshop. It uses an extended desktop arrangement and Photoshop at the pictures on the extended part of the office. You will find that the HP monitor is very steeped in colour and that it requires calibration to give you an accurate picture of how your photos will look once they are printed. Calibrate a screen for Photoshop work is a bit of an art in and of itself and there are software and hardware tools that help:

  http://www.drycreekphoto.com/learn/monitor_calibration.htm

• Satellite X 200-temperature of a faster microprocessor with the new RAM

  After the installation of 2 * 2 GB of RAM, the CPU temperature is now 47-49, idle, undervolted C 0, 9750v

  With 3 GB of RAM installed temperature CPU slowed 27 c, undervolted 0, 9750v
  Is there any dependence between CPU temp and how much RAM is installed?
  PS
  RAM is about 20% faster now, tested with benchMem

  Post edited by: latest

  Hello

  What new modules that you buy and this old modules that you used?

  I doubt you had a temperature 27 ° C CPU. Of course, it would be really nice, but these low temperatures never can have on cell phones. Even on the desktop, you have higher temperatures.

  If your computer is overheating laptop doesn t (stop, gel, etc), everything is ok and forget these hardware tools display the temperature. They often present temperatures wrong in my opinion.

• Portege 3480CT: cannot use the 16-bit PCMCIA card

  Hello

  I had a problem with a PCMCIA card (new media wave jammer, 16-bit) on a 3480 with Win98 & XP.
  The card appears as an unknown device in the "remove hardware" - tool.

  In Device Manager it does not at all appear and Windows did not ask for the driver.

  It looks like a card damaged, but still, this card works fine in another laptop!
  The problem could be related to different areas of memory used by the Cardservice.

  The Cardservice of the 3480 ct seems not be configurable.

  What can I do?
  Thank you

  Hello

  The PCMCIA card doesn't need a driver!
  To my knowledge, you must check the settings in the BIOS!

  On the second page of the BIOS, you should try to change the configuration of device for all devices and in the section of PC card, you must set the controller to Cardbus/16-bit mode

  then save the BIOS settings.

  Maybe it helps

• Question on the application of web camera

  Recently, I started my laptop Toshiba, as it does so, I became aware that the application of Web camera that is part of the installed software/hardware tools, has appeared on the desktop screen, as usual, but on this occasion, he disappeared again, I tried to locate and determine what had happened, but without success, to solve the problem or retrieve the application of the Web camera as a tool of the laptop It is rather limited and miserable as I video link with my daughter, London and is essential, apart from talk, see visually and vice versa.

  No advice and no information would be more appreiciative

  In general, default webcam app starts with Windows as small window pop up on the left side of the desktop.

  Unfortunately I didn t understand what happens with this application on your laptop but you can start it manually.
  Otherwise, if you use the webcam with other applications like Skype, webcam application must not start with Windows.

  The bottom line is this webcam is properly installed and listed in Device Manager.

  If there is a problem with the webcam in general please describe in detail what is wrong with that and we can try to help you.

• Tecra 9100 crashes after a few minutes

  My Tecra9100 (P4, 1.8 Ghz) freezes after a few minutes. He shows no reaction on the keyboard or mouse input.
  No matter if I am using Windows XP, Linux or simply enter the BIOS.

  Restart the system leads to a shorter period until the freezing point (a few seconds).

  First of all I thought about overheating of the CPU, but a small hardware tool shows me that the temperature is normal and the cooling fan works.

  Any idea? Maybe a problem with the VGA?

  Hello

  Yes, it s perhaps something wrong with VGA, but I think it could be a fault memory.
  Try to replace the modules and check if there is some performance enhancements.

  Otherwise, the technician must check the motherboard specifications
  You know it; It is always not easy to say what could be wrong without any diagnostic procedure

• Screen does not light after the start, but after standby on Satellite M100

  Hello
  I have some experience with computers and laptops, but this problem exhausted all of my knowledge.
  My girlfriend has a Toshiba Satellite M100, PSMA1E. He currently works on Windows XP, SP3.
  The laptop has always had problems closing/stand bye. He would stand bye and the screen would not. She would usually be manually turn off (holding the power button) and restart.

  Same thing happened last week, but with me. I turned off the power button but when I turned it on the screen was completely black. After a few attempts, I realized that everything worked; I could hear the usual audio files and XP Boot, but there was no way I could get the job of the screen.

  The strangest thing is that the CMOS/BIOS, one with the Toshiba logo settings screen, also does not appear. If it's an OS problem, I thought that I would be able to access the BIOS at least, but it does not work. FN + F5 does not work.

  Then, strange yet something happened. I was turning it on and off with keyboard shortcuts and I realized that if I put on stand bye using shortcuts and then go back on the screen turns on perfectly well (there is a cause of adjustment resolution icons are irrelevant, but it works perfectly fine).

  From that on I tried everything I know. Update the BIOS, all Windows XP updates, all Toshiba QuickFix, cleaning the registry with different tools, uninstall and reinstall the video driver (ATI Radeon X 1400) utility, shortcuts keyboard, power saver, tools hardware Toshiba, looking to start up programs, services, everything I could possibly think off.

  What intrigues me is that the Toshiba start screen will not be displayed. I can't access the BIOS, but I tried to restore the standard values of the BIOS with Toshiba hardware tools. It did not work. I don't even know if reinstalling XP will work because whenever I turn it on it is all black and I have to make the stand bye / Tower on Tower.

  When I have it plugged into an external monitor, I could see all starting the process (initial screen of the BIOS and Windows). I then tried to access the video driver display configuration but it would show only the external monitor. It would only detect the laptop screen after a stand bye / turn back on, and then it worked perfectly: the screen two screens simultaneously, extended, everything. Ah, changing BIOS selection automatic the LCD + external monitor does not work.

  I am really puzzled here and I can't understand it. I really don't think it's a hardware problem, because the screen works 100% after the stand bye. I guess that XP is do something during the closing down that completely 'stops' my screen, even after starting, and then I can only turn it on with the thing stand bye.

  Any help would be really appreciated!

  Best,

  Hi guys

  I had a similar problem on a series of Satellite A200 and I could solve works to update the BIOS and update the graphics driver.
  In addition, you must make sure that all available MS fixes and patches have been installed.

  Unfortunately, but that's all I can suggest. If the problem persists and you would not be able to solve update components then an ASP needs to check.

  Good luck

• Problem to connect a Macbook Air to Time Capsule

  I have a MacBook Air with 10.11.2. The TC I have 695 GB of 998 GB available.

  I tried several times to Run Time Machine on the TC. First it has green light in the airport and on the hardware tool, then a warning sign appears in the tool of the airport.

  No backup copy is made.

  All solutions?

  Anders

  When you open TimeMachinePreferences, have you assigned as the backup drive TC?, if so, delete and assign it again.

• How to record on an output table iterated data

  I want to save modified data (individual channels of data) in a table or an indicator that shows the ropes of checksums. As you can see from my attached code that each value is to be replaced by the following. I want to save all the iterations and not just the last. Need help please

  You are missing some basics of the works of LabVIEW. The son of control the flow of data, but do not store data. Whenever you write a value to your table, you replace what was previously shown on this table. You must use shift registers to store Info for the iteration of loop iteration, or you need produce table from the table using automatic indexation.

  Here's how you can do with a release of senior year under the loop condition.

  

  See also below for free training.

  "Give me six hours to chop down a tree and I will spend the first four sharpening the axe.  -Abraham Lincoln

  Here are some free training focused mainly on LabVIEW and hardware tools to help get started.

  Training center of NOR

  NEITHER start-up

  -Hardware Basics

  -Guide of MyRIO project Essentials (a lot of good simple circuits with links to youtube events)

  -LabVEW databases

  -DAQ Application tutorials

  -CRIO Developer's guide

  Learning OR training videos resources

  Introduction to LabVIEW for 3 hours

  Introduction to LabVIEW for 6 hours
  Paced self-study for students
  Self Paced Training beginner to advanced, required SSP

• Why push button and stop button does not work in the structure of the casing and buckle my VI? (code attached)

  I am a beginner. I'm trying to create a simple VI only switches beetween two types of signals like sine and triangle when someone press on the push button and at the same time, save the data in the file to my desktop. I also have a stop button which no longer record data.  Here are my questions and dproblems:

  1. when I press the button, it does not the true and false in the structure of the case so that I can see the triangle wave stops and begins the sine waveform table.

  2 when I press the stop button, I want the program still running, but the process of writing data in time the loop stops. I don't mind if the graph of the wave stops too but it would be better for the user to see the wave form is running, but the data will stop recording.

  3. Although the condition of the loop did not accept the local variable for the stop button inside the loop or within the structure of the case, so I put the button outside all the loops and the structure.  (I know that this is a problem, I do not know how to use a single button several times in a single code. The local variable did not work the world premiere? I have to?)

  4. the data file it creates hase a lot of lines and columns. I expect a time column and a column of mixed signals based on the push button amplititude this user press every time.  I did that with the acquisition of data and a sensor, it automatically gives me the voltage and time in a column. I tried 2D and 1 d and it has not changed anything.

  Thank you for your help

  

  

  Like you said, you read only your entries at the beginning, then whatever value they had before you hit run is worth to be seen by the rest of the code. Programming LabVIEW is based entirely on the data flow and parallelism. It is incredibly powerful and has led to its success over the years (coupled with graphical programming), but is usually one of the first things the new developers stumble on. This is a simple resource to familiarize themselves with its functioning. The function to highlight execution is a great way to watch how your application uses data streams.

  

  Simple code goes like this:

  • Containing the main code of while loop
    • Inside of the whole loop is all user interaction code or modify the code entry
    • Stop the terminal loop is attached to stop certain criteria or user selection of a stop button
  • Loop initialization above all if necessary
  • Closing referrals and communications, etc after all loop

  It's very simple code. If you want to watch in more advanced architectures that are scalable, Google "LabVIEW State Machine" or "LabVIEW producer consumer."

  If you are just starting, you should do a free training have the capabilities of LabVIEW.

  "Give me six hours to chop down a tree and I will spend the first four sharpening the axe.  -Abraham Lincoln

  Here are some free training focused mainly on LabVIEW and hardware tools to help get started.

  Training center of NOR

  NEITHER start-up

  -Hardware Basics

  -Guide of MyRIO project Essentials (a lot of good simple circuits with links to youtube events)

  -LabVEW databases

  -DAQ Application tutorials

  -CRIO Developer's guide

  Learning OR training videos resources

  Introduction to LabVIEW for 3 hours

  Introduction to LabVIEW for 6 hours
  Paced self-study for students
  Self Paced Training beginner to advanced, required SSP
  LabVIEW training Wiki