Different GUI interface on RV220W

Similar Questions

• How to change the GUI "interface use of traffic" of the ASDM

  I have an ASA 5510 and have recently added a second internet connection (primary) and an older DSL line that I now intend to use as a backup connection. Plan for this, I put the DSL on interface 0/1 and the T1s are 0/0. Unfortunately, the homepage of ASDM graphic practice is locked to 'DSL-Outside' interface (0/1) and I can't seem to find a way to change this for the 'T1-Outside' interface (0/0). Is it possible to do this? (perhaps an incantation of command line?)

  Thank you

  It depends on the security level of the interface. The chart shows the interface with the level low. Is there are 2 interfaces with the same level of security then it will go in alphabetical order.

  Please rate if this can help.

• Move on to a different physical interface same ASA L2L tunnel

  Some may describe the process to move a tunnel L2L existing since one physical interface to another?

  Thank you!

  Sent by Cisco Support technique iPhone App

  Add the map encryption to the new interface

  card crypto IPSEC interface new_outside

  You will also need to add isakmp to the new interface

  ISAKMP crypto enable new_outside

  If you have a new public IP address, then you will need to create a new VPN Group also.

• Bishop Calc - how not to use the GUI interface

  Hello
  
  New on Calc Mgr. How the call where I can just type in my Business Rule and do not use the GUI? Can't seem to find it.
  
  Thank you

  I think that you are referring to formulas that you would write in EA

  In Calc nursery, find your application, go to the database under the APP and expand it as well.

  You should see "Scripts" under there. Right-click on 'Scripts' and select 'new '. White screen will appear and write exactly as you would in the EA.

  Save the Script, then you must attach the script to a rule (you can simply use a shell if you wish). Save, validate, and deploy

  GL

• Difference between 2 different scsi interface

  Hello

  I have a small question about the difference between Virtual Device Node SCSI (0:0) and SCSI (1:0).  They have the same terms of performance? What are the disadvantages and advantages.

  Thanks in advance.

  James.

  I looked at the virtual device nodes only adding RDM, I prefer adding them to a knot of virtual device separated for better performance.

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

  F10

  http://KB.VMware.com/

• Connect together two GUI.

  Hi everyone, the joint is my GUI. Im trying to create two modes of the system. the first (running by optimization) who will be using this interface.

  the second (manual mode), which I want to move to a different GUI where I choose what he MORE stop the first GUI .and (running by optimization) when I back off the (ongoing optimization mode) I want (manual mode GUI) to stop.

  will it be possible?

  Please help me.

  Thank you very much

  
  

• I do not have the new GUI Windows Update for Vista

  My friends computer which has Vista: Home Premium SP1 has the new graphical interface of Windows Update.  I have Vista: Home Premium SP2, how do I do not have the new GUI interface?

  -Mike

  :

  Hi Gamemaster406,

  Welcome to Microsoft Windows Vista Forums.

  Until we start trying to solve your problem, please provide additional information, so that we can better help you. Please, give us a brief description of your problem with the computer.

  O how long you have been faced with this problem?

  O that you make changes to the computer recently?

  O are not able to see the latest version of windows you updates?

  Ø you aren't able to see the windows graphical user interface update settings?

  Each computer is different and you could look at the history of the update between the two computers and see if you are missing the other windows updates.

  To learn more information access Windows Update the link below:

  http://www.Microsoft.com/Windows/downloads/windowsupdate/learn/windowsvista.mspx

  http://Windows.Microsoft.com/en-us/Windows-Vista/install-Windows-updates

  Hope this information is useful.

  Suresh G

  Support Microsoft Answers

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite L670-1HD - problem with audio interfaces USB 1.1

  Hello

  I have a Toshiba L670-1HD with an Intel HM55 chipset, and an Intel Core i5 460M processor. I use this machine for my music software and that's why I use different audio interfaces external and USB-MIDI-Controller with build in audio interface like Mixvibes U - Mix Control Pro (http://www.mixvibes.com/content/u-mix-control-pro). These built-in audio interface are connected via USB 1.1. Always when I use this audio interfaces interfaces crash audio internalt - the sound is cracked very hard and there are noises in. The controller of all crashes sometimes too.
  When I use another interface audio as an audio interface Hercules DJ Trim 4 & 6 (http://www.hercules.com/uk/DJ-Music/bdd/p/102/deejay-trim-4-6/), which is a USB 2.0, everything works fine. No crashes, no cracks and no noise.
  You could say now that there is no problem and I should stick to the Hercules interface if it does no problem. The problem is that the Hercules is an audio interface only, there is no controller in it with which I can control my music software.

  I've updated all the drivers from the support page of this site without success. Is there a solution available or the Toshiba knows this subject? Am I the only one having this problem?

  Would be nice if a Toshiba official support employer could respond to this message. But this does not mean that I don't want to read somethng submitted by the user for which an index - all Board/Council/recommendation is welcome.

  Thanks in advance for the help!

  See you soon,.

  Stefan

  Hello Stefan

  In my view, you see the problem from the wrong point of view.
  Toshiba and each laptop manufacturer offer product and hardware and software support. So if there is a general problem with the functionality of the material you are by Toshiba on the right address.

  You use a third party and that you have some problems. Do you really believe Toshiba should support you and help to get this external peripheral work? In my opinion not. On the market, there are thousands of different devices and laptop computer how of the manufacturer must be able to test each of them and offer a solution?
  Something like that is definitely not possible.

  In my opinion, you should communicate with Mixvibes and ask for help. They have the best experience with own product and I presume that they are testing the features on different PC/laptop platforms.
  They should know how the device should work on new laptops with USB 2.0.

  It seems silly now, but Toshiba has nothing to do with it. If you have a general problem with the USB ports and they don t work with different devices that Toshiba should ask for help.

• Permutation of Interfaces of child object in a sous-schema control

  Greetings!

  I'm working on a project where I am trying to use a LVOOP magic.  My code is still a mess and accountable, so I'll try and keep this post direct and precise.

  My class tree is farily simple.  A parent class holds all the screws needed to replace and some common database information.  Each class of the child needs its own User Interface to run because each will have its own set of controls.  These controls to manipulate the internal settings of the object, and when the town 'Generate.vi' is called it displays text that the rest of my program then uses to complete the operation.

  My thought was that I could do a 'User Interface.vi' and 'Get User Interface.vi' as substitute it in my parent class.  Versions of these files children would then contain the necessary user interface, and the Interface.vi of the user would happen the reference to the Interface.vi of the user which would be then sent to the Sub panel and allows to get values in the final of the Interface.vi of the user when the user clicks on the "Generate" button in the Interface.vi of the user.

  This seems like a reasonable approach?

  I'm not sure I understand what you want, but this might be relevant.

  http://forums.NI.com/T5/LabVIEW/an-experiment-in-creating-compositable-user-interfaces-for/m-p/12623...

  http://forums.NI.com/T5/LabVIEW/A-more-successful-experiment-in-creating-compositable-user/m-p/12768...

  In addition, click on the links to see some more relevant info.

  Note that in general, it is claimed that classes should not export ISU because you can have different user interfaces (location, options, etc.).

• multi language interface

  Hello guys: I face a problem recently, my boss asks me a program with the interface in several languages, just different and the same background block diagram code, so at - it advice or ideas? I considered a method, package the main code and develop several Sub screws with different language interfaces, they all call this embed code. The best solutions? Thanks for your concern!

  Here is an article on area OR called the localization of your LabVIEW Application for different languages.  Take a look, too, in aid of LabVIEW for "bolt location.

  Jim

• Cannot access the ISE-3395-K9 CISCO Web GUI

  Hello

  I can't access the ISE-3395-K9 web gui interface concert 0 with ip address is 192.168.1.10.  I put the ip address of my labtop to 192.168.1.20 and could ping back but am still not able to access them through a direct connection between my labtop to concert interface 0 using one of the supported web browsers.  Any help would be greatly appreciated.

  It is possible that the GUI was configured to restrict access to only certain IPs / subnets. If 192.168.1.x isn't one of them, then you will have access.

  Are you able to connect to the shell via SSH? If so, you should check and confirm that all associated ISE services run by running the following command:

  show the application status ise

  Thank you for evaluating useful messages!

• How to change the user interface of the entity object indicators / Validation msg when running?

  Hello

  I use JDeveloper with version 11.1.1.6.3. Given my requirment details below.

  Suppose I have a (say 'EMPLOYEE_RATING') table in DB with the following structure.

  Columns:

  1 EmployeeId (Employee Id)

  2 RatingType (values can be in Stock or Bonus)

  3 RatingLevel (values can be 1, 2, and 3)

  Constraint:

  EmployeeId, RatingType and RatingLevel all together must be unique.

  Requirement:

  The customer's requirement is to have two screens of rating (one for Bonus another stock) and display different user interface boards and validations as follows.

  1 RatingType is a hidden field, are defined with the default (Bonus or Stock) based on the screen that the user opens.

  1. for the Stock screen, RatingLevel label should be "Stock note.

  2. for the Bonus screen, the label should be 'Bonus Rating'.

  3. for validation, the message must be 'Bonus note level must be unique' or 'Level of Stock of notes must be unique' ADB on the user screen opens.

  Implementation:

  I have a def EO (for example "RatingEO") and VO (for example ' RatingVO') def. Tips UI (Label) are given at the level of the OS. Also the unique constraint validation is made to EO with the message ' {0} and {1} must be unique, where {0} is source.hints.EmployeeId.label "and {1} is source.hints.RatingLevel.label.  I also did the shuttle two different instances of the VO (EmployeeRatingBonusVO and EmployeeRatingStockVO) in the request form (although BonusTaskFlow and StockTaskFlow are set to open with the new transaction, Intension of the two shuttle different named instances is to have the common code in VO. impl class but can run different business logic code by checking the name of the instance of VO)

  Question:

  Since I have two different pages, I can define two different labels in the jsff, but I can't change the commit message defined at the level of object entity based on open display. At the opening of the screen, depending on the type of screen, I should be able to change the label specified at the level of the entity object. (It should not affect the definition but only the instance). As this entity object cannot be distinguished (if it belongs to Bonus or Stock), I have problem on how to change the indicators of UI during execution.

  Any help on this would be appreciated! Thank you.

  Rami

  Post edited by: rami

  I tried your script.

  I created the secondary key with EmployId and rating level. I added validation of Unique key. In failure handling handling section of the validator, I gave the error message like: {0} must be unique. For token 0: I gave RatingType (here RatingType is the name of the attribute in OT).

  We give the default for RatingType as Stock Bonus in VO. kind RatingType get its value or Stock Bonus based on the original Version that we use.

  I hope this helps.

• VISA makes about LV freeze

  Hello

  I use VISA read & write to interface a USB converter to FTDI FT232BL series. The FTDI driver created a virtual COM port.

  Everything worked fine with a few weeks with 8.51 LabVIEW 8.0 and 8.2. But all of a sudden my VI froze when I ran my stop code.

  Fortunately, I was able to track it down to close VISA, with poster simply he is running (using the symbol of a yellow bulb), but never ends. I can close the other windows of LV except the Project Explorer and the VI running at a higher level. Red Abort-button is clickable, but shows no effect.

  Open the VISA Session Monitor VI in the labview\vi.lib\Utility\visa.llb shows no VISA public sessions.

  When I kill LabVIEW by using the task manager of Windows, a different process LabVIEW.exe stays there (it says that I don't have the right to stop him) and a new LabVIEW session hangs at the time.

  I activated "sessions VISA narrow auto ' but it does not seem to make a difference

  Someone is experiencing similar difficulties?

  I tried VISA 4.3 and 4.4 with LabVIEW 8.51 on Win2000. Also, it comes as an .exe built on another PC and use also to a different GUI with the same interface hardware screws (those with VISA opportunity open/r/w/close)...

  concerning

  Marco

  He points to a blockage in the version of the dll FTDI.

  What version do you use? Have you checked for an update on the FTDI web?

• How to use the shutdown command to stop another computer?

  I just saw the setting-m to the shutdown command and decided to give it a whirl. However, when I pointed out the computer in question, I received a message that "a required privilege is not owned by the customer.

  What should I do to be able to use my laptop to turn off my old desktop computer? Both are running XP Professional SP3.
  Sometimes, I like reading or watching streaming video on Hulu on the laptop while lying in bed, and sometimes I play music if do the first, which is stored in the form of MP3 files on the desktop (which I access via a share). Be able to turn the office without getting up would be nice, but you do not get this option with Remote Desktop.

  Here is the result, the office is "slickswintel" (he's old, and since when I went first from Mac to Windows 98SE, although it is now a double XP/98) and the laptop is "slickslaptop".
  Both machines have unprivileged called 'Slick' on them local accounts that are my accounts on the day the main day. I have a different admin account, but I only use it as needed and use runas as often I log in fact.

  What should I do to get the following to work? In spite of the passing the MCSA Exam, I never learned about this feature, so I'm not sure what I should do to make it work? It'll work on a workgroup or is it only for domains? While I could set up a domain with the copy of the server I got from Dreamspark, I really didn't need one.

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  D:\Documents and Settings\Slick > shutdown /?
  Usage: shutdown [-I |-l | s | r-|-a] [-f] [m \\computername] [t xx] [-c 'c
  COMMENT'] [d up: XX: YY]

  No args display this message (same as to-?)
  -i Display GUI interface, must be the first option
  l log off (cannot be used with the - m option)
  s shut down the computer
  r Shutdown and restart the computer
  -an abandonment, a system shutdown
  -m \\computername Remote to cancel the shutdown/restart computer /.
  t xx Set timeout for shutdown to xx seconds
  -c 'comment' comment (maximum of 127 characters) stop
  Forces f - running applications to close without war
  Ning
  d [u] [p]: xx:yy reason for closing code
  u is the user code
  p is a planned shutdown code
  XX is the main reason (the positive integer code
  SS to 256)
  YY is the minor reason (the positive integer code
  SS to 65536)

  D:\Documents and Settings\Slick > stop s m \\slickswintel
  The operation completed successfully.
  A required privilege is not held by the client.

  D:\Documents and Settings\Slick >

  As a general rule, you must have administrative privileges on the remote computer to shut down this computer.  Given that both computers have XP Pro, you are halfway there (remote users always authenticate as 'Guest' on XP Home).  The computer that you are trying to close must have "Simple file sharing" disabled because otherwise you can not authenticate to this computer as anything except the user "guest".  So try to disable Simple file sharing, make sure that your user name and password are the same on both computers and make sure you have administrative privileges on the remote computer, and then you can stop the machine with the command "shutdown".

  "How to disable the file sharing simple and how to set permissions on a shared folder in Windows XP"
    <>http://support.Microsoft.com/kb/307874 >

  In fact, it's easier to use the remote desktop.  Even if you do not have a "Shutdown" option in the start menu, you can always open a command prompt window (start-> Run-> "cmd") and enter the command:
  stop s f t 35
  This will give you 35 seconds to logoff this computer before its judgment (assuming that you have administrator privileges).

  You can also look in the command "psshutdown' of the PSTools Suite
  PSTools: <> http://technet.microsoft.com/en-us/sysinternals/bb896649 >

  HTH,
  JW

• Unzip command

  What is the command to unzip or extract files from the prompt with the default Zip program in Windows 7?

  I know how to do it using GUI interface, but I have since discovered that this is not possible using the CLI interface (that's what I ask) unless you get a different zip program.  Thanks for your reply, however.