Disable Split Tunneling - SAs are not when I change crypto ACL
Hello!
When I change my ACL Crypto I receive an error message in phase I: "PROPOSAL_NOT_CHOSEN NOTIFIER' of IKE. I do this to disable the ST and get all the hollow tunnel traffic. Please see the config below:
crypto ISAKMP policy 10
md5 hash
preshared authentication
life 3600
ISAKMP crypto key cisco address x.x.x.x
!
!
Crypto ipsec transform-set esp - the esp-hmac-md5 ENCRYPTION
!
crypto map ipsec-isakmp CLIENT 1
defined peer x.x.x.x
game of transformation-CRYPTO
match address 115
!
access-list 115 permit ip 10.10.10.0 0.0.0.255 10.10.11.0 0.0.0.255
access-list 115 deny ip any one
I changed the ACL 115 to so I can disable split tunneling, and it looks like this:
access-list 115 permit ip 10.10.10.0 0.0.0.255 any
access-list 115 deny ip any one
What is a failure? I have donthink the crypto ACL must be the same?
OK, you use a card dynamic encryption on your head just as I suggested, so that's fine. What you have done, which is causing your problem (and usually causes more problems than it's worth), is to assign an access list to the dynamic encryption card. It is not necessary, because with a dynamic encryption the router head card accept any model of traffic the remote router sends.
In your case since you changed the remote router to be 'all', it is no longer maps to the 115 ACL on the head and now is failing.
Way easier around it is simply to remove the 'match 115' address card dynamic encryption on the head. This will not affect any of your other tunnels and allow the remote router to establish a tunnel.
The exact commands you would use are as follows:
> crypto dynamic-map PERSONAL 10
> no address for correspondence 115
Tags: Cisco Security
Similar Questions
-
XP Pro, SP3. I downloaded the free Bullzip pdf printer. Somehow my old printer pdf in my printer disappeared list which I have used for years. I get this message when installing - "you are not allowed to change the settings for this printer. If you need to change the settings, contact your system administrator. I click ok and it ends, but it doesn't work. It does not appear in the printer control panel as a printer to change anything.
I built this computer at home and I'm the only one using it. What is this function 'administrator '? I've never had to administrator on any program. Never. That is what it is?
CNET is infamous for the grouping of things in its downloads as much a / v programs report as junk (I went through the same thing using eSet NOD32 has / v). I seem to remember that if you ignore the warning and download the exe file and then use a tool like the free 7-zip to extract only the file necessary to run the program you want, you can work around the problem.
For a pdf printer free which is not CNET - and works well - go here--> http://www.cutepdf.com/products/cutepdf/writer.asp
EDIT TO ADD A LINK:
See, for example, http://forums.cnet.com/7723-12543_102-582307/safe-downloads-cnet-com-sorry-but-not-anymore/
-
Not sure if there is an error or a breach of security on my system, but my Mcafee Cox Security Suite client will say sometimes randomly the Parental control has been disabled, and the network firewall and Internet has been disabled and must be fixed. When you click on fix, the problems will go away, but sometimes the Protection status check will reappear do later me wonder if someone attempts to access or attempt to take control of my computer in some outside way. Using Windows Defender and Mcafee Viruscan I found nothing so far, however in one file past a Nakido.exe was found and attempted to remove, it is no longer, but I seem to always be able to find traces of the file on my computer, which makes me wonder if the Trojan horse still has limited access to my computer and try to manipulate items and just has not been detected yet.
Try to contact McAfee Support for assistance. But before that try one of these:
(1) Windows Update
(2) try to install the latest Service Pack
(3) ensure that your compatible version installed in Windows otherwise (ask McAfee upgrade option to the compatible version) -
GPS latitude and longitude are not when no signal
Hello
I am buliding a BB 9700 GPS application. I am able to get the latitude and longitude through cellTower (using the Service Provider signal), but I am unable to get the latitude and longitude when there is no signal. I tried the criteria to false, but the lattude and longitude do not come.
Please find the code below
private LocationProvider _provider; private Criteria _criteria; boolean deviceReciever,cellSignal; String longitude, latitude,altitude,speed; private void FixLocation() { resetProvider(); /** Initialize Criteria and LocationProvider instances. */ deviceReciever = true;//receiving lattitude and longitude to phone gps reciever cellSignal; = false;//Disabling ph signals setupCriteria(); createLocationProvider(); if(_provider!=null){ try{ _location = _provider.getLocation(5); locationUpdated(_provider, _location); }catch(InterruptedException e){ //log(e.getMessage()); System.out.println("Exception called --->"+e); }catch(LocationException e) { //log(e.getMessage()); System.out.println("Exception called --->"+e); } /*--> try { System.out.println("babaji"); System.out.println("The _interval="+_interval); _interval = -1; _provider.setLocationListener(this, _interval, 10, 20); } catch(Exception e) { System.out.println("Exception called-->"+e); } */ } } private void resetProvider() { if (_provider != null) { _provider.setLocationListener(null, 0, 0, 0); _provider.reset(); _provider = null; } } private void setupCriteria() { _criteria = new Criteria(); if( deviceReciever == true ) { _criteria.setCostAllowed(false); } else if( cellSignal == true ) { _criteria.setHorizontalAccuracy(Criteria.NO_REQUIREMENT); _criteria.setVerticalAccuracy(Criteria.NO_REQUIREMENT); _criteria.setCostAllowed(true); _criteria.setPreferredPowerConsumption(Criteria.POWER_USAGE_LOW); } } private void createLocationProvider() { /** * Initialize _provider using _criteria. */ try { _provider = LocationProvider.getInstance(_criteria); } catch (LocationException e) { } } public void locationUpdated(LocationProvider provider, Location location) { if (location != null && location.isValid()) { QualifiedCoordinates coordinates = location .getQualifiedCoordinates(); speed = Float.toString(location.getSpeed()); longitude = Double.toString(coordinates.getLongitude()); latitude = Double.toString(coordinates.getLatitude()); altitude = Float.toString(coordinates.getAltitude()); System.out.println("Longitude --->"+coordinates.getLongitude()); System.out.println("Latitude---->"+coordinates.getLatitude()); System.out.println("Altitude->"+coordinates.getAltitude()); } }
The longitude and latitude are coming as null always if we I'm reciving the gps via the mobile gps receiver. If the signal of the mobile service provider then uses the lang and lat come.
I don't want to use the service provier signal for lattitude and longitude.
Please suggest me the error I made in the above code and assistance.
Thanking you
Standalone GPS works best outdoors, with a clear view of the sky. At the very least, near a window.
You can experiment with the timeout.
(If these answers answer your question, please mark the thread as solved. (Thank you).
-
RV042 - disable split tunneling
Hi all
I am currently using a firewall RV042 linked to an another RV042 via the VPN Site to Site.
Everything works fine and dandy, however, I want to disable internet access on one of the RV042s.
Is there a way I can disable the split on the RV042 tunneling to achieve? It doesn't seem to be what I can find on the menus that claim.
Looking forward to some counselor here.
Thank you!
jag_lin84,
The firewall allows all outbound traffic and blocks all incoming traffic by default. You can create an access rule to block all outbound traffic.
Action: reject
Service: all the
Newspaper: -.
Source interface: LAN
Source IP: no
Destination IP: all
-Marty
-
Tags are not when you type a keyword in the address bar
Already when I typed a tag in the address bar - bookmarks Tags would be present. Now very rarely this happens to you and instead the engine search terms search appear.
To search for tags/keywords, I now have to open bookmarks and search in there. Very annoying... it sucks big time. WTF happened?
Thank you Joe
You can add a space and a + to search for tags in the address bar.
-
MS Office files are not when you do a combine
Acrobat 11.0.09 MS Office file types are listed is no longer trying to create a combined file. I browse a directory and only PDF files are listed, although it contains other (.docx, .xlsx etc)
Figured it out. Repair moved from MS Office and Acrobat now shows the types of MS Office files to combine.
-
I just upgraded to CS6 and for some reason any my page changes post on my site. It is said that the index file has been transferred, but it wasn't. And ignored others. Any suggestions? I'm a rookie at this level if ok to dumb down to the explanation. Thank you very much. Janet
To update your browser, press Ctrl + R or F5.
Nancy O.
-
See that login replication server are not in the Administrator Console view
I installed a laboratory environment to view with 2 connection view CS1 and CS2 (replica) servers. I use VMware-viewconnectionserver-x86_64 - 5.1.2 - 928164 for v5.1.2 installation.
After installation and reboot of the servers, I don't see that CS2 listed under the connection servers, only CS1 appears in the list. However, when I connect to the console administrator display on CS2 replica server, I see the two servers in the list.
On verification of registry settings on the servers, I find the correct entries under HKEY_LM\Software\VMware, Inc. \VMware VDM\ServerInstanceType 1 on CS1 = and = 2 on CS2. I chose to set Windows Firewall rules to be updated automatically during the installation. Both servers are on the same VLAN.I am able to connect to the virtual desktop when connecting using the client independently discovers a connection server, but after doing some additional testing, I found that pairing does not work properly. I've disabled its own console CS1 and updated servers on CS2 and CS1 watch still active console after several updates. I have also tested CS2 console, I disabled CS1 but it does not reflect this change on the console of the server CS1.
What I understand is the grouping and pairing does not have settings for some reason any. I've tried 3 - 4 times install it on vanilla installs Windows 2008R2 and every time I get the same results. I wonder if anyone has experienced a similar problem.The problem was caused because the DNS server did not correct entries of the second CS server for resolution of these two names before and back. (I changed the IP address)
-
Muse do not save the changes inside the text boxes
Several (but not all) pages on my site of Muse are not saving the changes I make inside a text of some box. I can not specifically with the choice of font, size, color, line spacing and super/index. I tried to disable in-browser editing and some of the pages have since begun to save but not to save even more. After I made changes and saved the site, when I close the program and open it then later these paragraph changes back to the original.
I am very confused about why it's only a few pages and why that is the case at all. Any ideas or solutions would be useful! Thank you!
I think I found a solution. It seems that the problems I had with the changes that do not stick were somehow connected to the tool 'copy of development shaped at all breakpoints. Once I started into implementing shaped each breakpoint by hand he started saving properly.
-
XP pro do not start after changing the Boot.ini file
The problem is that my C: partition Windows 7D: has XP ProThese should be considered right resp. partitions 1 and 2?
I wanted to first XP pro to start the default partition.
A few days ago, I made a change to the boot.ini file. But since XP Pro was not starting at all.
I tried XP Pro to start first that the default partition.
Given that XP Pro and my D: drive have not been starting, I consulted the boot.ini file in C:, Windows 7 partition and I changed the order (i.e. partition No.) in the boot.ini file and saved it to the required location, i.e. D:/WINDOWS/pss.through my drive C: of work, i.e. the partition of Windows 7, but it still does not work because apparently even though I save here, the actual values and the paths of the partition are not actually be changed on the system. I confirmed this by going into the CMD shell switching to D: and by running the command D: > bootcfg.Apparently any values I save in the boot.ini file that I save as a text file or "All files" in D:/WINDOWS/pss/it does not actually change in the system because whenever I run the command bootfg values are remaining still and not able to be changed, because apparently it is not saved in XP Pro and the D : partition. No matter what I do and what I put in the boot.ini file to access the values through the windows 7 partition, the values that bootcfg returns me are always the same and he refuses to change the name of path or anything else. No matter what orders, I also put in bootcfg himself.These are the values that bootcfg gives me:
default: multi (0) disk (0) rdisk (0) partition (1) \WINDOWSBoot entries:
Boot entry ID: 1
Friendly name of operating system: MS Windows XP Professional
Path: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS
The operating system load options: / noexecute = OPTIN/FASTDETECT/usepmtimerMy XP Pro partition is simply not booting, and it of my main partition and has all my work. It is imperative that it starts.
My Windows CD is also not start because apparently my DVD drive does not work properly, I had the anti malware threatfire (ThreatFire) installed on my XP D:Windows program disk but have uninstalled just in case it was blocking my changes to the system.
On C:Win7, I put the default operating system option in the Advanced tab for Win7 and the D:XP Pro to XP Pro, when he was the starter and work. Now I can only access my files D:XP Pro Player C:Win7. But XP is not just start. What shd - I do? Thks.
I don't have a very practical windows CD but my CD/DVD drive is not read and does not properly.
Looks like your original post stated that your cd/dvd does not work.
Respectfully, you will continue these hap hazard patches and your computer will not start at all. I'll try to help you once again. Please follow closely.
Start your computer by loading Windows 7. Click HERE and download EasyBCD. Install the software in trial version. Once installation is complete open EasyBCD. You will see an interface like the image below. Click Add a new entry.
A new screen appears as in the image below. Use the drop down menu to select Windows NT / 2 k/XP / 2 k 3 as described below. Type the name of the operating system in the box below. Of course, it will be Windows Xp (you can add the home or Pro to the name if you want). Make sure now that there is a check mark in the box "automatically detect the correct player. Once you have completed these steps click on 'add an entry '. That's all! You are finished. If all goes well, and if you have followed these steps carefully, there, now you have a system dual boot.
You can now start working on your cd/dvd problem.
-
Windows - Internet access, no split Tunnel L2TP VPN Clients does not
Greetings!
I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.
I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.
Here is the configuration:
: Saved
:
ASA Version 1.0000 11
!
SGC hostname
domain somewhere.com
names of
COMMENTS COMMENTS LAN 192.168.2.0 name description
name 75.185.129.13 description of SGC - external INTERNAL ASA
name 172.22.0.0 description of SITE1-LAN Ohio management network
description of SITE2-LAN name 172.23.0.0 Lake Club Network
name 172.24.0.0 description of training3-LAN network Southwood
description of training3 - ASA 123.234.8.124 ASA Southwoods name
INTERNAL name 192.168.10.0 network Local INTERNAL description
description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
description of Apollo name 192.168.10.4 INTERNAL domain controller
description of DHD name 192.168.10.2 Access Point #1
description of GDO name 192.168.10.3 Access Point #2
description of Odyssey name 192.168.10.5 INTERNAL Test Server
CMS internal description INTERNAL ASA name 192.168.10.1
name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
description of training3-VOICE name Southwood Voice Network 10.1.0.0
name 172.25.0.0 description of training3-WIFI wireless Southwood
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif INSIDE
security-level 100
255.255.255.0 SGC-internal IP address
!
interface Vlan3
nameif COMMENTS
security-level 50
IP 192.168.2.1 255.255.255.0
!
interface Ethernet0/0
Time Warner Cable description
!
interface Ethernet0/1
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/2
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/4
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/5
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/6
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/7
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
boot system Disk0: / asa821-11 - k8.bin
Disk0: / config.txt boot configuration
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
INTERNAL DNS domain-lookup
DNS domain-lookup GUEST
DNS server-group DefaultDNS
Name-Server 4.2.2.2
domain somewhere.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
the DM_INLINE_NETWORK_1 object-group network
network-object SITE1-LAN 255.255.0.0
network-object SITE2-LAN 255.255.0.0
network-object training3-LAN 255.255.0.0
object-group training3-GLOBAL network
Southwood description Global Network
network-object training3-LAN 255.255.0.0
network-object training3-VOICE 255.255.0.0
network-object training3-WIFI 255.255.0.0
DM_INLINE_TCP_2 tcp service object-group
EQ port 5900 object
EQ object Port 5901
object-group network INTERNAL GLOBAL
Description Global INTERNAL Network
network-object INTERNAL 255.255.255.0
network-object INTERNALLY-VPN 255.255.255.0
access-list outside_access note Pings allow
outside_access list extended access permit icmp any CMS-external host
access-list outside_access note that VNC for Camille
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
access-list outside_access note INTERNAL Services
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
no pager
Enable logging
exploitation forest asdm warnings
Debugging trace record
Outside 1500 MTU
MTU 1500 INTERNAL
MTU 1500 COMMENTS
192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
enable ASDM history
ARP timeout 14400
Global 1 interface (outside)
(INTERNAL) NAT 0 access-list sheep
NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
NAT (GUEST) 1 0.0.0.0 0.0.0.0
5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
Access-group outside_access in interface outside
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server Apollo
Apollo (INTERNAL) AAA-server Apollo
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 INTERNAL
http 0.0.0.0 0.0.0.0 COMMENTS
No snmp server location
No snmp Server contact
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
correspondence address 1 card crypto outside_map INTERNAL SITE1
card crypto outside_map 1 set of peer SITE1 - ASA
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
address for correspondence card crypto outside_map 2 INTERNAL training3
outside_map 2 peer training3 - ASA crypto card game
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
address for correspondence outside_map 3 card crypto INTERNAL SITE2
game card crypto outside_map 3 peers SITE2 - ASA
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
delimiter group @.
Telnet training3 - ASA 255.255.255.255 outside
Telnet SITE2 - ASA 255.255.255.255 outside
Telnet SITE1 - ASA 255.255.255.255 outside
Telnet 0.0.0.0 0.0.0.0 INTERNAL
Telnet 0.0.0.0 0.0.0.0 COMMENTS
Telnet timeout 60
SSH enable ibou
SSH training3 - ASA 255.255.255.255 outside
SSH SITE2 - ASA 255.255.255.255 outside
SSH SITE1 - ASA 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 INTERNAL
SSH 0.0.0.0 0.0.0.0 COMMENTS
SSH timeout 60
Console timeout 0
access to the INTERNAL administration
Hello to tunnel L2TP 100
interface ID client DHCP-client to the outside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd ping_timeout 750
dhcpd outside auto_config
!
address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
dhcpd Apollo Odyssey interface INTERNAL dns
dhcpd somewhere.com domain INTERNAL interface
interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
enable dhcpd INTERNAL
!
dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
enable dhcpd COMMENTS
!a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.43.244.18 prefer external source
WebVPN
allow outside
CSD image disk0:/securedesktop-asa-3.4.2048.pkg
SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
enable SVC
Group Policy DefaultRAGroup INTERNAL
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
Group Policy DefaultWEBVPNGroup INTERNAL
attributes of Group Policy DefaultWEBVPNGroup
VPN-tunnel-Protocol webvpn
Group Policy DefaultL2LGroup INTERNAL
attributes of Group Policy DefaultL2LGroup
Protocol-tunnel-VPN IPSec l2tp ipsec
Group Policy DefaultACVPNGroup INTERNAL
attributes of Group Policy DefaultACVPNGroup
VPN-tunnel-Protocol svc
attributes of Group Policy DfltGrpPolicy
value of 192.168.10.4 DNS Server 4.2.2.2
VPN - 25 simultaneous connections
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
the value INTERNAL VPN address pools
chip-removal-disconnect disable card
WebVPN
SVC keepalive no
client of dpd-interval SVC no
dpd-interval SVC bridge no
value of customization DfltCustomization
attributes global-tunnel-group DefaultRAGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Disable ISAKMP keepalive
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
attributes global-tunnel-group DefaultWEBVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultWEBVPNGroup
tunnel-group 123.234.8.60 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.60
pre-shared-key *.
tunnel-group 123.234.8.124 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.124
pre-shared-key *.
tunnel-group 123.234.8.189 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.189
pre-shared-key *.
type tunnel-group DefaultACVPNGroup remote access
attributes global-tunnel-group DefaultACVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultACVPNGroup
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
inspect the they
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
: end
ASDM image disk0: / asdm - 623.bin
ASDM location Camille 255.255.255.255 INTERNAL
ASDM location INTERNAL CGT-external 255.255.255.255
ASDM location INTERNAL SITE1-LAN 255.255.0.0
ASDM location INTERNAL SITE2-LAN 255.255.0.0
ASDM location INTERNAL training3-LAN 255.255.0.0
ASDM location INTERNAL training3 - ASA 255.255.255.255
ASDM location INTERNAL GDO 255.255.255.255
ASDM location INTERNAL SITE1 - ASA 255.255.255.255
ASDM location INTERNAL SITE2 - ASA 255.255.255.255
ASDM location INTERNAL training3-VOICE 255.255.0.0
ASDM location puppy 255.255.255.255 INTERNAL
enable ASDM historyI should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.
You must configure * intercept-dhcp enable * in your group strategy:
attributes of Group Policy DefaultRAGroup
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.comIntercept-dhcp enable
-Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked. It is located on the Advanced tab of VPN client TCP/IP properties. Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.
Alex
-
Love tunnel SAs negotiated, but do not survive.
Background
We have a stable P2P GRE + IPSec configuration to multiple rays using signatures rsa for authentication ISAKMP and EIGRP as the routing protocol. We are in transition to a love (DMVPN) configuration. GRE P2P tunnel interfaces are administratively shutdown, cryptographic cards on physical interfaces have been removed and the cryptographic database has been erased.
Question
When implement us the interfaces of tunnel love (Star), we are able to complete the ISAKMP phase I and II (briefly). However, ~ 1-1/2 minutes more, we see a message from debug on the hub, such as:
13:56:49.601 Jul 21 EDT: IPSEC (cleanup_tun_decap_oce): Unlock and null to Tunnel0 tun_decap_oce 86742E48 of 86FB990C of ident
... and then the IPSec SAs are deleted, the tunnel down, IKE_PHASE2_DEL and IKE_PHASE1_DEL messages are generated and start with phase I ISAKMP negotiation.
Anyone know what the 'CEO '?
Highlights of debugging (ISAKMP and IPSec)
13:55:13.188 Jul 21 EDT: ISAKMP: (2597): SA authentication status: authenticated
13:55:13.236 Jul 21 EDT: ISAKMP: (2597): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE
13:55:13.356 Jul 21 EDT: IPSEC (create_sa): its created.
13:55:13.356 Jul 21 EDT: IPSEC (create_sa): its created.
13:55:13.356 Jul 21 EDT: % CRYPTO-5-SESSION_STATUS: Crypto tunnel is MOUNTED. Peer: 500 Id: spoke.domain.null
13:55:13.356 Jul 21 EDT: % DMVPN-7-CRYPTO_SS: Tunnel0-socket is in PLACE
13:55:13.700 Jul 21 EDT: ISAKMP: (2597): former State = new State IKE_QM_R_QM2 = IKE_QM_PHASE2_COMPLETE
13:56:49.601 Jul 21 EDT: IPSEC (cleanup_tun_decap_oce): Unlock and null to Tunnel0 tun_decap_oce 86742E48 of 86FB990C of ident
13:56:49.601 Jul 21 EDT: IPSEC (delete_sa): deletion of the SA.
13:56:49.601 Jul 21 EDT: IPSEC (delete_sa): deletion of the SA.
13:56:49.601 Jul 21 EDT: % CRYPTO-5-SESSION_STATUS: tunnel Crypto is out of SERVICE. Peer: 500 Id: spoke.domain.null
13:56:49.601 Jul 21 EDT: ISAKMP: (2597): entry = IKE_MESG_FROM_IPSEC, IKE_PHASE2_DEL
13:56:49.605 Jul 21 EDT: ISAKMP: (2597): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DELNote: A more complete debug output is attached.
General comments (sh crypto isakmp, ipsec crypto sh its)
ISAKMP Security Association reached a State of QM_IDLE and active status. However, the SA is removed and a new is generated on the breast of ~ minute.
IPSec security associations are negotiated on the hub and the spokes. However, only speak it a program package, and only the hub has decaps. Wireshark confirms that the hub does not all ESP packets on the wire. The IPSec SAs are deleted and the new spawn every minutes ~ 1-1/2.
See the output of the command
hub #sh cry ipsec profile
Profile IPSEC DMVPN
Life safety association: 4608000 Kbytes / 3600 seconds
Answering machine-only (Y/N): N
PFS (Y/N): Y
Diffie-Hellman group: group2
Transform sets = {eni-xfm-des: {esp - esp-sha-hmac}, eni-xfm-3des: {esp-3des esp-sha-hmac}}hub #sh cry map
Card crypto isakmp-65536-"Head-Tunnel0-0" ipsec
Profile name: DMVPN
Life safety association: 4608000 Kbytes / 3600 seconds
Answering machine-only (Y/N): N
PFS (Y/N): Y
Diffie-Hellman group: group2
Transform sets = {eni-xfm-des: {esp - esp-sha-hmac}, eni-xfm-3des: {esp-3des esp-sha-hmac}}Card 'Head-Tunnel0-0' 65537-isakmp ipsec crypto
Map is a PROFILE INSTANCE.
Peer =.
Extended IP access list
access-list allow accord host host
Current counterpart:
Life safety association: 4608000 Kbytes / 3600 seconds
Answering machine-only (Y/N): N
PFS (Y/N): Y
Diffie-Hellman group: group2
Transform sets = {eni-xfm-des: {esp - esp-sha-hmac}, eni-xfm-3des: {esp-3des esp-sha-hmac}}
Interfaces with card crypto Tunnel0-head - 0:Tunnel0HQ-edg01 #sh cry session detail
Current state of the session cryptoInterface: Tunnel0
Duration: 00:00:10
The session state: UP-ACTIVE
Peer:port 500 fvrf: (none) ivrf: (none)
Phase1_id: spoke.domain.null
DESC: (none)
ITS IKE: localremote 500 500 Active
Capabilities: (None) connid:2682 life time: 23:59:47
ITS IKE: localremote 500 500 inactive
Capabilities: (None) connid:2681 life time: 0
FLOW IPSEC: allowed host 47host
Active sAs: 2, origin: card crypto
On arrival: dec #pkts'ed 6 drop 0 life (KB/s) 4517257/3589
Outbound: #pkts enc'ed drop 0 0 life (KB/s) 4517258/3589Material & IOS
C1811 (hub) - c181x-advipservicesk9 - mz.124 - 24.T
c1711 (spoken) - c1700-advipservicesk9 - mz.124 - 15.T9Follow the relevant parts of crypto configurations DMVPN (hub / talk):
crypto ISAKMP policy 3
BA 3des
Group 2
life 86399ISAKMP crypto identity hostname
Crypto ipsec transform-set eni-xfm-3des esp-3des esp-sha-hmac
transport mode
Crypto ipsec transform-set esp eni-xfm-des-esp-sha-hmac
transport modeProfile of crypto ipsec DMVPN
3600 seconds, life of security association set
the value of the transform-set eni-xfm-des eni-xfm-3des
PFS group2 Setinterface Tunnel0
IP255.255.255.0
Protection ipsec DMVPN tunnel profileNote: PNDH, love, and no other settings have been chiselled.
Any help would be appreciated.
Best regards
MikeYou are right your comment.
The previous interface of p-BRMS (in your case) can get his information in to
the tunnel endpoint database (packages of controls tunnel) even if the
p BRMS tunnel is stopped. It is also in the code a GRE packet
destined to the router will search a mathc with a p-BRMS tunnel before
Love tunnels. If the GRE tunnel packets were getting "caught".
by p-BRMS tunnel and then dropped.
If I really want a GRE tunnel to be 'down', I'll remove the "source of the tunnel...". ».
If I have two tunnels upwards at the same time, I do what you do, give
each of them a different tunnel key or a different source of tunnel.
Hope this helps to understand what was going on.
Mike.
PS. You should be able to mark it as answered present.
-
Icons are not displayed properly in Gmail when the zoom level is between 150 and 200%
Icons in Gmail will not correctly displayed in Firefox at all zoom levels. The problem does not occur in less than 150% zoom levels or levels of zoom to 200% or more. Levels of zoom between (150%) correct icons are not displayed until the mouse passes on their location.
The attached pictures show screen shots to 140% (OK), 150% (problems shown, before moving the mouse), 150% (problems shown, after moving the mouse), 190% (problems) and 200% (now OK again)
The problem was not resolved by disabling extensions, go to mode without failure or update Firefox.
Firefox and extensions/plugins are all fully patched.
You can try to disable hardware acceleration in Firefox.
- Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
You will need to close and restart Firefox after enabling/disabling this setting.
-
I have an ASUS K501N laptop.running 7 Home premium.
Sometimes when I turn on it the office/display is not so strong, if I click on Spider I get a flag your who says run the game in software rendering mode hardware acceleration is disabled or not supported by your video card driver happens whensleep and Hibernate options are not available.
Other times that everything works correctly.
Anyone know why and how to remedy
Hi leflaneur,
1 when was the last time it was working fine?
2. did you of recent changes on the computer?
3. when there is no sleep and hibernate options available?
4. are you able to play other games on the computer?
Method 1
I suggest that you enable the acceleration of the display on the computer and check if the game works.
(a) open settings display by clicking the Start button, clicking Control Panel, appearance and personalization, customization, and then clicking display settings.
(b) click on display settings, and then click Advanced settings.
(c) click the Troubleshooting tab, and then click change settings. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
(d) move Hardware Acceleration complete.
Method 2
If the previous step fails, then you will need to download and install the drivers for the graphics cards updates by visiting the card manufacturer's Web site and check if it helps.
Updated a hardware driver that is not working properly
I hope this helps!
Halima S - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think.
Maybe you are looking for
-
How to drain the battery is considered as normal?
I bought a MBP 15 "(MacBook Pro with the Retina display, OS X Yosemite (10.10.5), Core i7 2.5 GHz, 16 GB of DDR3 memory) in January 2016." Although this particular model has 9 hours of wireless web browsing, I find his behaviour pretty weird lately.
-
Satellite L40-139 - need driver Windows XP Home edition for 'ethernet '.
Please can you send me the link to Satellite L40 ethernet control model of laptop for Windows XP Home edition?
-
Title says it all.
-
Error code 5005 Keithley 2602 not detected
Hello I use the Keithley 2602 A meter/source in labVIEW2011. An error code 5005 product (wholesale value) on the display. This error is not detected by the driver. In the pilot of the world ErrorQuery maintains False even if an error occurs. If I put
-
I am a student trying to buy labview 2013 online. I found a site selling labview 2013 which has a very good price. http://www.studica.com/national-instruments-students-NI-LabVIEW-mydaq/LabVIEW-Student-Edition.html I just like to make sure that it i