Disorder of the WRT54G Wireless - G Router!

Similar Questions

• Spend the WRT54GS to WRT54G2 Router?

  I am running the Linksys WRT54GS router.  A family member gave me a unopened, still in sealed box WRT54G2 router which they never used.  For routers that I have to start all over with the installation of the new router or is there a setting in the configuration of the web which would allow me to simply select an update of the ot the router option to the new?

  You can just save the settings of the router and copy it to the new. However, you can take a screenshot of all the settings on each tab, and then do the same on the new router.

• With the wrt54g router wireless security - separates the WLAN LAN clients

  I have a wrt54g router and want to separate clients WLAN access to computers and servers on the local network... in other words, I want to make a 'guest' network I put the router in 'router' instead of 'bridge' mode I want just to be sure if it's the best thing I can do in terms of transforming the network wireless in an isolated.

  Check out the 3rd party firmware like dd - wrt.

• Using WRT54G as the second wireless with E2500

  Have read the threads on this, I want to make sure I have this correct.

  Currently I use the E2500 as my main router at my house (top).  I replaced my WRT54G with the E2500 to my DSL connection throughout the House.

  I run an ethernet as a hard link at the bottom of my smart TV cable.

  I now add another device (Channel Master DVR +) that it will also take an internet connection.

  I need two connections from an ethernet cable (already run down).  After reading a bit, looks like I can use my old WRT54G as a secondary router/switch down.  (Sorry if I'm not using the correct terms).

  In order to get my two connections (Smart TV and DVR +) I need at least a separator, or something?  However... "Why not extend my lower wireless for a stronger wireless connection down?" was my way of thinking.

  How can I configure my E2500 to recognize the WRT54G - run two difficult connections to my TV and DVR + and also extend a stronger signal wireless downstairs for my daughters iPod Touch?

  Thanks - Glen

  Who did the trick! You Rock! Thank you so much cub for your help and quick of Reid. I may be back later this week when my DVR + gets here but hope not. Thanks again!

• The best wireless router?

  Hi, so my network wireless router works little during these three days, and I think to buy a new one.
  First of all, I really want the network at high speed. And also the range. I want to high power.
  In addition, my brother and I'm an online game called Minecraft and sometimes we have had trouble with delay. I don't really want to do with my new router, so can you tell me what router should I buy?
  Oh, and if I need to tell you which computer that is using my family's here.
  We use all of the Mac.

  And also, what is the difference between AC1200 and AC1900 or AC3200?
  I'm sorry but I'm beginner...

  Ago, the WRT54g now is becoming old and can't handle the bandwidth and other band. It is not even GB supports side LAN I think. AY, you are going to be interested in a WRT1900AC. Been working fine for me and I make game on XBL. I don't know so I not Wii or NDS experiences between people and the WRT1900AC router.

  Provider of Internet and the Modem Configurations
  Which Service provider Internet do you have? Cable or DSL?
  What ISP Internet Modem MFR. and model # you have?
  What Modem ISP link service accelerates upward and down are you?

• WRT54GS Wireless Router recently started disconnecting Internet connection after 9 months

  Hello, I have read some and see that it is a problem common but of are to be decided.

  I have a Lynksys WRT54GS with the latest Firmware update v7.2 27 July 2009 (FW_WRT54GSv7.2_7.2.07.013_EN_20090727)

  I ran 2 desktop computers as well as my DVR security by the security cameras for remote monitoring, also portable hook upward wireless sometimes as well without any problem using this router for over 9 months now with no problems until the last few days... I never log out and leave it on 24/7 for 9 months without problem and now recently I had to pull on the power cord from the back of the router and reconnect it to re power on the router to establish an internet connection.

  Now the last 3 days the router loses its internet connection each monutes a few... hours... the time it disconnects are random moments and I have the programs I need to run all day but can't because the router loses its connections...

  I applied the firmware again... re factory - configure the router... rebooted the computer... tried cloning the MAC address... all seem to be doing nothing... the same problem still exists.

  All of the minutes or hours so it disconnects the interent.

  I ran the office computer directly to the DSL Modem and I'm online very well with a desktop computer without disconnections for hours and hours (18hrs to date is not a problem), so I know this isn't the access provider. I had this problem I believe before with a previous Lynksys router and then bought it and now after this short period it seems to do the same thing again with this one. What a pain in the but.

  All solutions and more...

  Re application firmware... then

  factory re set the router... then

  re - connect computers as if it were a new router... the MAC address cloning? Geezus... it must be one simple solution other then buy another brand router.

  Thanks in advance...

  What is the IP address, find the modem directly...? Connect the computer directly to the modem and check the ip address? What is the ip address, you get the router...?

  Try the following settings on the router and check the connection...

  -Change the channel to 11-2 wireless, 462 GHz

  -Under the Advance wireless settings tab, change the tag at 50, Fragmentation threshold to 2304, interval RTS threshold to 2304

• Replacement of the WRT54G Router

  I have a router that my cable company feel needs replacing. I don't really know if it's true, because they tried to sell me a new router or rent one for me. In any case I guess that replacement is necessary. I'm not a geek and my existing WRT54G Router was installed by someone else who went through all the work to set up my network home. Ideally, I would buy the same model router and use existing lines to connect the new router, thus reducing to a minimum the installation time and trouble. Of all the posts on this site, I am sure that installing a new router is not easy to do and is subject to many 'traps '. People spend days, installation of a router and a good number of them fail. It seems incredible to me that a manufacturer could produce a product that causes so much wasted time of clients and anguish.

  I am running Win XP ver. 3 with IE version 7. I'd like some experienced advice on which model of router would be ideal as a replacement for my WRT54G that was enough for my home network. So I would advice on the question of whether I should try to do it myself or hire a geek to do to me. I have next to zero patience and no tolerance for poorly written instructions. For those who have traveled down the road, I'm ready to go, tell him from me right.

  Router WRT54G is one of the best routers.

  Choose the router from Linksys E series (model E1000, E2000 and E3000). These routers are very easy to install. The speed and intensity of the signal will be very good compared to the WRT54G Router.

  You need not hire a technician to install the router. You will get a Cisco software connect with this router. Just run the CD and Cisco connect software will do everything for you. It will protect the wireless automatically for you.

• CAN I turn stop wireless to router but always send signals to an external antenna via the port?

  Can I stop/start of my Wired main WRT54G wireless and always send the signal through a WAP browser & directional external antenna plugged into the hub?

  How to allow only my own devices to use my bandwidth?

  Using WPA password on WRT hub.

  Drive Blu - Ray and AT & T Microcell Tower allow other titles-WPA2...?

  Can I block the antenna attached to the main hub of sought but allow the port to send signals at access point?

  Shields of aluminum foil over the main router antenna would cease its output signal? (if I remove them to allow the occasional portable navigation)

  If you want, you can disable the feature on your primary router WRT54G wireless and use WAP to send the wireless signal.

  Open the router configuration page and go to the Wireless tab, change the mode of network to people with reduced mobility. Save the settings.

  If your wireless network is secure only your wireless computer can connect to the wireless network and use the bandwidth. So, make sure your wireless network secure.

  Consult the manual for your Bluray and AT & T Tower and see if they take in charge WPA2.

• Router WRT54GS wireless can not connect to internet

  I am now using a WRT160N router, everything is ok, nothing happens

  I have a (ver 6) WRT54GS wireless router that I have not used for 2 years.

  yesterday I took the WRT54GS out of the Junk box and replaced the WRT160N by the WRT54GS

  I have a desktop computer that is wired & wireless laptops. My Office recognizes the local network and my laptop signal but the my router cannot connect to the internet.

  I tried everything:

  reset

  firmware update

  but nothing has worked

  If anyone can help. my ISP is comcast and it comes to my modem http://www.motorola.com/Consumers/US-EN/Consumer-Product-and-Services/Cable-Modems-and-Gateways/SURF...

  Bypass the router and connect the master computer directly to the modem.

  Make sure that you can access the Internet on your primary computer directly via the modem.

  Connect the modem to the Internet port and main computer to the Ethernet port on the router.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 30 seconds. Power cycle the router and reconfigure it manually.

  Follow this link to configure the router with cable Internet service.

• Working Group stopped after the installation of the new wireless router

  My working group stopped working after the installation of the new wireless router.  Router was switched were to move from DSL to fiber optic.

  I have a very simple home with two laptops working group, the two are connected with a wireless router.  A PC is running XP with the updates and service packs; the other PC is Windows 7 Home premium.  This working group was running without problems for a few years.  The Working Group has been used to share files between two laptops.  Internet access was through the DSL wireless router and print was with a wireless printer, without going through the working group.

  I had my DSL set out to free fiber optic last week, which meant that a new wireless router has been installed by my local phone company.  Internet works fine; wireless printer works.  The working group no longer works.  When I try to connect from XP to Win7 and I click on mode workgroup computers, I get this message:

  WorkGroupName is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

  The network path was not found.

  I tried to create a new working group, the new name for the same workgroup on both machines, but this did not help.  Working groups are supposed to be simple; This seems to be a problem on the new router - telco tech support says that nothing is stuck on the router. I don't believe them.

  What version of XP you use (Home or Pro)?

  Can you access the Win 7 a XP computer?

  You have identical accounts, passwords on both computers?

  If all that was done was to change routers without making any changes on the computers, the most likely cause of the problem is a third party (other than Windows) firewall on at least one of the computers.  Being by default, a router automatically assigns IP addresses to computers on your local network.  Different brands of routers, but use different address ranges.  For example, Cisco/Linksys routers typically use the 192.168 form addresses. 1.1 with 192.168. 1. 254, while the D-Link routers typically use 192.168.1 to 192.168.0.0. 254.  A firewall configured to allow only the first IP range blocks communication to the scope of the latter.

  So... What is the name and version of your anti-virus program?
  What other security software is installed?

  On every laptop computer, open a command prompt window
  for XP: start > run > cmd > OK
  for Win 7: type cmd.exe in the search box and press enter
  In the black command prompt window, type the following command and press enter
  ipconfig

  Please provide the values for the following for the adapter wireless of each computer
  IP (XP)
  IPv4 address (Win 7)
  Default gateway

• I can't connect to my router and my system XP Pro/SP3 has NOT installed the automatic Wireless Configuration service. How can I get that re-installed?

  I have the latest driver for my Linksys WPC54GS PCMCIA card. The Linksys software does not support WPA security, which supports my rout (and I do not want to use WEP).  The zero wireless Configurator, this is what I need, but the service is not installed on my Windows XP Pro w / SP3 System.

  Hello

  You need not be. I posted a link to google cache, so keep scrolling down, the answers are displayed below. It contains details on the manual creation of the registry key for the zero configuration service.

  You can also export to a working system.

  See you soon.

• I configured the netgear wireless router and works fine but when I turn the computer power off and back on I can't get connection

  Hi can anyone help, I am with AOL, I just switched to the Platinum service, I configured my router netgear DG834G wireless and that's all works fine, but if I turn the computer then turn it back I cannot get a connection and when I ask her to fiind wireless networks the computer tells me that windows does not support my wireless network and I must have another program running , but I didn't so I have to reload the settings again for windows to set it up. What happens whenever I turn off the computer. AOL are without help please someone has any ideas - I use windows xp service pack 3

  Hi Timstimpson,

  It is possible that the Automatic Configuration Windows wireless service is not configured to run at startup.
  Try the following:
  1. click on Start and run
  2. type in the box to run services.msc
  3 scroll down and look for the Automatic Wireless Configuration service
  4. double-click on the service and make sure that the Startup Type is set to Automatic
  
  
  Let me know if it works for you!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot access the configuration of my router (wrt54g) page

  I can't access the page of my router (wrt54g) configuration after the installation. The router works fine, but whenever I try to connect to 192.168.1.1 it says the password is incorrect. The first time that I put up I changed the default user name and password and I thought I'd simply forgotten, so I reset the device. This time I don't change any of the default values, and I can not even log on. I have to reset it several times, and you're just annoying. Anyone know how to prevent it from happening? I thought it might be a firmware issue, but I can not find all downloads for my version of road ' rs (V8). I use a macbook pro, osx 10.9.2.

  My neighbor has pretty much the same question. Did some research and found many people with similar problems. Probably time for a new...

• VAIO w / Vista connect wireless but I can't access the internet on my router

  Help.  I have a SONY VAIO with Vista.  Just totally reformatted.  I can access my router (NETGEAR WNR 2000v2) locally, but cannot access the internet.  Curiously, I can connect to unsecured networks and access to the internet.  How can I solve the problem with my router/computer? I removed the 3rd party (Norton) security and made a few other commands nothing done. (BTW - I have 3 other devices that work fine on my wireless router.)

  Hi barry909,

  ·         You get the error message?

  Follow the steps in the article.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Reference: http://windows.microsoft.com/en-US/windows-vista/Wireless-networking-frequently-asked-questions

• WRT54G - cannot connect computer wired to the internet through a router

  I have the WRT54G and unable to connect to the internet when you are going through the router.  I feel that I've checked everywhere can, but still does not work.  I connected the way the instructions, the lights are on the case and all that.  I have cable internet and when I plug directly, there is no problem.  When I try to 'ping' to check the connection between my computer and the router, I get "Request Timed Out".  I tried to reset the router and goes in this direction, but I can't go beyond checking the internet connection through the router.  Any ideas what I'm missing?

  Thank you!

  You should not use the installation CD at all.  If you throw it away.

  See here for the installer of cable.