Double signals

Similar Questions

• Cannot connect my Withings equipment to time capsule 5-2, 4 ghz

  Cannot connect withings Aura and the scale of the new Time capsule. Get the message: not compatible with 5.0 ghz router. But the capsule is supposed to have 2.4 ghz also.

  any solution?

  THX

  The time Capsule is a 2.4 GHz and 5 GHz signal at the same time.  The two bands using the same default wireless network name.

  In theory, a wireless device is supposed to choose the best quality signal with which to connect based on its own capacities and distance compared to the router.

  Some devices only 2.4 GHz... printers, in particular... seem to get confused by the double signals and they have a hard time, choose the frequency band of correct with which to connect.

  What might help is to use the AirPort Utility option to assign a different name for the 5 GHz wireless network. Then, the 2.4 GHz network has a name and the 5 GHz network has a different name... then you can run a device wireless to connect to 2.4 GHz or 5 GHz network this way.

  

• PCI-6534 receives data to clock twice

  I have a simple test developed in place to check the operation of the card PCI-6534.  A written test generator a double-ended (hi-lo) word of 16 bits of zeros with one being bitshifted to the left (MSB).  It is sent to a custom Board that converts the double signal over single-ended and then sends the map of PCI-6534.

  Something like this:

  0000000000000001

  0000000000000010

  0000000000000100

  0000000000001000

  0000000000010000

  etc...

  I have two different computers and each has a PCI 6534 installed with exactly the same configuration accept the driver.  Computer 1 PCI-6534 driver version 1.12.0f0 (circa 2006).  Computer 1 shows the diagram above as expected.  Computer 2 a driver 2.0.0f0 (circa 2007).  2 computer shows the diagram below:

  0000000000000001

  0000000000000001

  0000000000000010

  0000000000000010

  0000000000000100

  0000000000000100

  0000000000001000

  0000000000001000

  0000000000010000

  0000000000010000

  So, it looks like 2 computer gets the same data on the top and bottom of a clock cycle.

  I was about to check the clock seen by 6534 on computer 1 against 2 computer the data generator trial to show the difference.  However, in doing so, I discovered that now 2 computer shows:

  0000000000000001

  0000000000000010

  0000000000000100

  0000000000001000

  0000000000010000

  I can't reproduce the problem even if I ask the question!

  Any ideas?

  Thank you!

  We have two different vintages of differential boards.  It turns out that the newer boards have a slightly different flavor of the chips that the older 26LS32.  When we swapped the chips on the latest map with those of the former, we were able to solve the problem.

  So, with the non-functional chips installed, if we turn the clock low slow reeeaal, we can get multiple samples of data such as the differential line noise is enough that she takes back as clock.  If we turn up to, say, 6 MHz all right.  It is because at that time, the clock runs at a higher frequency than the noise and overclocking the card.

  I still have yet to understand what the parameters are new chips really are the root cause of the problem, but it works.

  -Shrew

• I am trying to configure MÜDE for my organization using Oracle BI administrator and have some questions about its feasibility. Please help me.

  I'm looking for in the MUDE (multi development environment - user) for future developments of the RPD and I tested various scenarios and I came across a few questions:

  1. do you think that we can add new objects to an existing project without checking in?

  2. in case I missed a few items for development while creating a project, so how do I add them to the project?

  3. special security on objects - it can handle special security on objects (example fields assigned to hidden only)?

  4 should we we look at a timetable of the releases (only the new changes to RPD each 60 / 90 days?)

  I know that few issues may be vague, but any idea on those who could help me a lot.

  Thank you in advance!

  I don't want a double amount of answers. Because I have no response from the other group felt that it was in the wrong place or group sleeping and it took a double signal. Of course, I will be closed one of them when the answers start coming.

• Realization of comparator: constant double input signal - waveform, threshold.

  Hello

  How achieve the comparator, where the input signal's waveform type (from data acquisition) and the threshold is a double constant.

  These two types are incompatible, then a conversion must be made. Which one?

  Thank you

  Pavel

  
  

• Flash readers 'double' all video signals

  Since yesterday, after the Flash Player update indicates videos 'double', like a 3D signal. (See photos)

  
  I tried with FF 3.6.13 and Opera 11.01. I am using Win XP SP 3 with all latest updates. All other flash content works witout problems. Turn on/off the "hardware" example has no effects.

  

  

  OK, so I noticed in another post that 10.2 allows hardware acceleration.

  Right-click on the screen

  Goto settings

  Click on the tab 1

  Uncheck the hardware acceleration

  close and reload the page

  should be back to normal

  Enjoy

  D

• Double counters in Signal Express with a USB-6229

  I have a USB-6229, which I'm running via SignalExpress, and I am trying to simultaneously record two inputs of meter.  However, it seems that he has trouble to add the second channel.  When I add the first string via signals acquire > DAQmx Acquire > counter entry > Position > angular and select ctr0 channel, he (correctly) lists PFI8 and PFI10 as inputs of channels A and B.  However, when I add the ctr1 channel to the same task (via the blue and the button "Add a channel"), he still lists the same PFI8 and PFI10 as input.

  On the other hand, if I first add ctr1 then add ctr0 Secondly, it lists PFI3 and PFI11 as A and channel B for the two entries of meter.

  How can I get the two counters operating independently?

  Thank you

  Josh

  He realized that I can't run two meters of a single task in Signal Express (unlike, say, two analog inputs).  Once I added it as two separate tasks, everything works fine.

  Now I have problems of synchronization.  Looking through these tips and documentation, it seems that I will not be able to fix this via SignalExpress, so I continue in LabView.  I'm having some problems with it, but I'll post in a new thread here.

• Z5 double guard falling mobile data signal

  Purchased and received my Xperia Z5 Dual of a seller decently well known on Amazon a few days ago. After putting my SIM card, I got mobile signal (advocate and text), but no data, so I took it to T-mobile, and they got that running. Since then, my freqnently data falls to zero bars of signal, then comes back to the top in about a minute then drop again a minute later. The wifi signal seems to do that too, although it seems to be in bars full all the time in my house, when I play a mobile game, I can tell he falls signal when it is lagging on every few seconds.

  Should I return it as broken and buy a new one? I am inclined to think that the question is not on the end of my career, because I had no signal with this SIM card problem in my last phone, a very old Moto X. My friend suggested it was probably a hardware problem (specifically, the faulty antenna Board), but I don't know a lot about hardware, so I don't know whether to take his suggestion at face value or not.

  Hi anastvns,

  Do you get the same results with WCDMA/GSM without selected LTE?

• Port of question - no video - DVI double separator i7-HDMI > DVI

  What I'm missing here?

  I have an i7 2.3 g-Mini late2012.  10.8.5. in a studio where I fed a dual display

  using a separator of video signals by - everything first, Tripp Lite, now an Aluratek - DVI 2-port video splitter (powered

  units).

  Followed by all the good order in start-up, the device worked for maybe a week and a half.

  Walked away and returned after maybe 48 hours either from Friday to Monday.  Computer is running

  "sleep" mode... The attempt, no signal wake video monitor not recognized.  Powerd deactivation/activation, no change.

  Reset PRAM and disconnected/reconnected Mini power after 30 seconds... tried reconnect splitter/monitors...

  sequence... still no resolution of the video signal to not watch.  Indicators on the splitter show the signal of the i7.

  and connectivity to the monitors.  I excluded this device that the fault.

  Am following the process mfgr correct insofar as the separator like so new out-of-box in reconnecting

  power on it - getting nothing.  Strange thing is, I had the same problem with the Tripp Lite - that's why I

  bought this Aluratek separator to replace.  Now, same problem.

  When connected to same monitors, this worked fine right out of the box.

  Now the same problem as the other separator.  Changed two different HDMI > DVI

  cables. All cables. No change.

  Either monitors directly linking ON the HDMI Mini port - display works fine.

  Tried the MiniDisplay port to the separator. didn't work...

  Which may conflict in operating system - something making these monitors sleep, something system-wise

  who is disrupting this process?  Even pulled all other connections (external USB port stuff) and it

  did not solve.

  It is also a coincidence for two separators to fail with this same issue - seems to indicate something with the

  Mac. In the meantime, no double posting until I can understand it.

  Any help greatly appreciated-

  Thank you

  Mike

  I suspect the power adapter... and maybe check for a loop of mass too.

• Mini display to HDMI adapter double link

  Can I use a mini display HDMI Dual link adapter to connect 3 HDMI TV to a Mac Pro?

  I never heard of a "Mini display Dual HDMI link.

  There are double-ling mini displayport > DVI adopters as the double bond is required for DVI so a resolution higher than 1920 x 1200.

  You can get the dispatchers who will share a single HDMI into two identical signals. You may be able to get one which divides into three signals. A power supply may be necessary for a this type separator

  A dispatcher will give identical screens on each monitor.

  What model Mac Pro?

  What card graph (s) installed?

  Want a different output on each monitor?

• Airport Time Capsule: Suspected of weak signal

  Hello

  I have 3 Apple wireless devices all. The main router is the ATV, followed of an Airport Extreme, extending the network and a former Airport Express, also the extension of the network. Briefly, it is a three-storey house, on the first floor of which is a daylight basement (windows and doors on three sides), then the second and third floor (all wood of the frame).

  I'm almost completely Mac/Apple-centric (my son except for the PC game), there are 6 Mac (PPC and Intel) and 4 iPhones on the printers network every day, matching, smart TVs and casual with a device visitors or 2. Generally, there is no connection problem apart from the complaints unfounded. There are a variety of El Capitan, Yosemite, Leopard, OS 9.2.1 and iOS operating systems. Computers are my MBP to 2008, two MacBooks circa 2010, 1 iMac (circa 2010), 1 lime iMac 400 has PPC G4 MDD and iPhones - 5s and 6s (2 of each).

  I studied this weak signal suspected by the search for possible answers on the internet, try to use various applications to diagnosis Wi - Fi and browse the various parameters of the airport. I was not able to "find" a smoking gun or even a reason suspected for the signal is so poor. "So poor" refers to my dissatisfaction with our signal coverage - my expectation!  It is perhaps as good as it gets and I have too wait.

  The layout has my ATC in my office, ground floor, the west wall of the House and approximately 4 ft above the ground. The AExt (from ATC) is through an open door and a flight of stairs and on the ramp (half wall). If you stretched a string directly between ATC and AExt would be 16' - 20'. The AExp bounced around, but currently it is in our gym, which is part of the structure of individual garage. The AExp is approximately 45 ' - 50' of the AExt and 65' or from the base (ATC). My goal is to explain the variety of signals.

  I'm not the most scientific. To drive off the coast, I don't understand why there are 4 WiFi signals reported. 2-5 Ghz and 2 to 2.4 Ghz. "The only basis ' creating a wireless network" is the ATC, the other two are "the extension of the network. There are 2 reported BSSIDs and I forgot how to determine who is what hdwr.

  Walk with a MB and it is Wireless Diagnostics app, it seems, most of the signal issues are explainable. One unexplained is when I get out the MB to the gym, the signal "through the roof" - it probably doubles in strength, and that's where the Express is maybe 60' of ATC. Sounds good, but why, when I go back to ATC, the fact the signal drop in half. I want to Express signal overall. I guess the Express to be the weak link, but of course does not appear like this. My main computer, the MBP, sits 15' and at glance of ATC and gets that weak signals - I guess that it could be the Airport card in the MBP, but I'd like to think not, that I have no way to test it. I'm sure that all this has to do with the 4 signals being broadcast and the differences between networks 2.4 Ghz and 5 Ghz.

  So, why is my best farthest signal from the router (ATC) and why is it the MBP of low signal (MB too), the nearest router. Oh, I have no neighbors to 500' or more. Sorry for writing a book.

  The layout has my ATC in my office, ground floor, the west wall of the House and approximately 4 ft above the ground. The AExt (from ATC) is through an open door and a flight of stairs and on the ramp (half wall). If you stretched a string directly between ATC and AExt would be 16' - 20'. The AExp bounced around, but currently it is in our gym, which is part of the structure of individual garage. The AExp is approximately 45 ' - 50' of the AExt and 65' or from the base (ATC). My goal is to explain the variety of signals.

  When you extend a wireless AirPort network using intermediate connections wireless base stations, it is important to understand how fundamentally. So please forgive me if I go to the places you already know.

  Extended wireless airport works wheel - as with the base station extend over the hub of the wheel. Each of them extending base stations would be on a spoke of the wheel. With the new 802.11ac 802.11n base stations, you can not extend linearly. For example, in your game both the extreme and the Express would be on another spoke in the wheel, step along the same spoke. Make sense?

  That said, the station of further base your Express, would have a harder time getting a signal strong enough to expand it, while extreme may not have this problem. Basically, this would explain the gap between the quality of the signal between these two base stations.

  I wrote an an airport users points to try to help to how to best place a base station that extend. It may be useful.

  To drive off the coast, I don't understand why there are 4 WiFi signals reported. 2-5 Ghz and 2 to 2.4 Ghz. "The only basis ' creating a wireless network" is the ATC, the other two are "the extension of the network. There are 2 reported BSSIDs and I forgot how to determine who is what hdwr.

  By default, each of your simultaneous dual band base stations provide actually two wireless networks; one on the 2.4 and the other on the 5 GHz bands. Base stations extending each of these repeat if they are in the range. Note that the higher frequency band (5 GHz) would have a harder time penetrating objects, such as walls, ceilings, etc. and it is basically only usable in the same room. I'm guessing what to do in distance between base stations, the extreme is able to expand both networks, but the Express (especially, if it is a model of generation 802.11n 1) extend one or the other.

  For routers to Apple, the BSSID is the MAC address wireless base station itself.

  One unexplained is when I get out the MB to the gym, the signal "through the roof" - it probably doubles in strength, and that's where the Express is maybe 60' of ATC. Sounds good, but why, when I go back to ATC, the fact the signal drop in half. I want to Express signal overall.

  To each base station that spread, the level of the signal from the base station can be high, but real bandwidth of the signal will be the same as what he receives in this place. Yes, you can see a high (full bar) signal level, its ability to transfer data will be reduced because of this limited bandwidth. The key is to place the base station that extend to a resort beach it is the extension to get the specific width of possible higher bandwidth SNR. It is covered in the tip that I quoted above.

• Messages in double (EGTT/receiver) ing.

  Hello. I noticed that I sometimes get/receive messages in double (iMessage, MMS and SMS) with sometimes low and no wifi and cell (ular) connection on my very old iPhone 4S with its iOS v9 (.3.2 now). Is this normal? Thank you in advance. :)

  antdude wrote:

  Hello. I noticed that I sometimes get/receive messages in double (iMessage, MMS and SMS) with sometimes low and no wifi and cell (ular) connection on my very old iPhone 4S with its iOS v9 (.3.2 now). Is this normal? Thank you in advance. :)

  Yes this is normal...

  especially if someone send an imessage and you're signal is bad, you will receive a text and then later when your signal is better receive you imessage for the same person, it has occurred to me a few times.

• Monitors flicker and "Input Signal Out of Range"

  Hello!

  I have a Mac Mini (end 2012) 2.3 GHz Intel core i7 running up-to-date El Capitan, with two HP monitors 2071d.

  These monitors have DVI connections. It is connected with Mini DisplayPort to DVI adapter, and the other with HDMI to DVI adapter (provided with the Mac Mini).

  Everything has been fine for a year until this week. Two monitors are:

  (1) intermitantly began flickering of the scrambled images

  (2) flickering intermittently at black or white noise

  (3) intermittently flickering white noise

  (4) the message of the form 'input out of range Signal. 1600 x 900 at 60 Hz settings."

  How is this problem go and come, but rather continues today.

  After research, I tried to start safe mode, but the problem persists.

  I read that put the computer to sleep and then wake up could solve this problem... it worked a

  couple of times, but the issue soon returned.

  I tried to reset several times VRAM/LANDAU and SMC.

  I doubled checked all the connections.

  Under the system of preferences > display (when the image is stable long enough for me to see) everything looks OK. Under the screen of the 'Default display' tab is selected. On the color tab, there are three HP2071d listed (with a selected) in the window display profiles. I've linked by selecting one of the other "HP2071d" listed without noticeable change.

  I also reset both monitors to factory settings via the menu screen of the monitors.

  I also came across this mini Mac EFI Firmware Update 1.7 for flickering on end of 2012 Mac Minis, but when I tried to run I got "this software don't is not supported on your system. Ugh. It turns out that my Mac Mini is already updated to MM61.0106.B0A (2015-002)

  My Information System > Hardware > graphics/display info is:

  Graphics Intel HD 4000:

  Chipset model: Intel HD Graphics 4000

  Type: GPU

  Bus: integrated

  VRAM (dynamic, Max): 1536 MB

  Seller: Intel (0 x 8086)

  Device ID: 0 x 0166

  Revision ID: 0 x 0009

  Exhibition:

  HP W2071d:

  Resolution: 1600 x 900 at 60 Hz

  Per pixel: 32-bit color (ARGB8888)

  Display serial number: 6CM3171PFF

  Mirror: on

  State of the mirror: mirror material

  Online: Yes

  Rotation: support

  HP W2071d:

  Resolution: 1600 x 900 at 60 Hz

  Per pixel: 32-bit color (ARGB8888)

  Display serial number: 6CM3170P31

  Main screen: Yes

  Mirror: on

  State of the mirror: mirror of Master

  Online: Yes

  Rotation: support

  I am of the ideas of what else to check/try.

  Thanks for any assistance that anyone can provide.

  bdcs64 wrote:

  Hello!

  I have a Mac Mini (end 2012) 2.3 GHz Intel core i7 running up-to-date El Capitan, with two HP monitors 2071d.

  These monitors have DVI connections. It is connected with Mini DisplayPort to DVI adapter, and the other with HDMI to DVI adapter (provided with the Mac Mini).

  Quite the same configuration except here, with 2 Samsung S22B310 DVI monitors on an i5 2.5 GHz in late 2012.

  Everything has been fine for a year until this week. Two monitors are:

  (1) intermitantly began flickering of the scrambled images

  (2) flickering intermittently at black or white noise

  (3) intermittently flickering white noise

  (4) the message of the form 'input out of range Signal. 1600 x 900 at 60 Hz settings."

  How is this problem go and come, but rather continues today.

  Both monitors isn't good. Which would lead us to think that the Intel HD 4000 is overheating and the problem is not with any of the adapters or cables. Although, if one of the cards was not internally, it could put additional heat stress on the graphics chip.

  Personally, I will try a few things.

  1. turn off, unplug everything, open the bottom cover and give it a good cleaning to make sure it cools properly.

  https://www.iFixit.com/device/Mac_Mini_Late_2012

  2. try each monitor individually for awhile configurations see if the problem follows the monitor cable adapter installation.

  (I know he'll be a brake after obtaining used monitors to double)

  3. try using > MacFanControl to monitor and help control the temperature of the GPU ITPP.

  http://www.CrystalIDEA.com/Macs-fan-control

  FWIW, I do not use screensavers, but I do a lot of videos as well as some games of light on both my 2010 and 2012 of the Mini and I really believe that MacFanControl has really helped to extend the life of graphics on these two systems.

  I use the control based on the sensors on the sensor of GPU ITPP and configured so that it starts slowly rise in power of the fan above 129' F

  

• hp2009 monitor turns on says no signal goes to sleep mode.useing a hp6000

  power system off and then on again, lights monitor says no signal and goes to sleep

  Hey there @mholmes940, I thank you for joining the HP Forums!

  I understand that the monitor says no signal and goes to sleep.

  Please try a few steps mentioned below.

  Click Start, Control Panel, system and Maintenance and then click Power Options.
  Select high-performance, and then click on change plan settings.
  Change the settings to never.
  Click on the button Save changes to accept the changes and restart the computer.

  Also make sure that the graphics card is up-to-date.
  1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. in Device Manager, look for graphics card you want to update, and then double-click the device name.
  3. click Driver tab and click on set to update driver and follow the instructions.

  Additionally, make sure that the cables that connect you to monitor are correctly connected, or use a different video cable.

  I'll watch for your reply.

  Have a great day!

• HP Pavilion DV7 6154ea: HP pavilion DV7 6154ea connection keeps losing signal

  Experiencing Wifi connection problems where the signal falls systematically after maybe 10 to 15 minutes of use. Is underway for the past 2 months or so. Guess it was my network, but after going through the configuration of the router, check connection on other laptops HP at home that work perfectly I guess something must be set right.

  Has been informed by a member of support Paul who was very helpful to help restore me the laptop to windows 8 to 7.

  Having recently upgraded to the SSD, perform a new installation of the OS a few days where drivers when installed through the ordered recovery disks, HP support, you are prompted to any update more or less all the drivers using the new assistant support, I would add much like ago.

  In any case on the device noticed Control Manager are now 4 cards under network adapters:

  -Intel(r) centrion (R) Wireless-N-1030

  -Microsoft Virtual Wifi Mini Port adapater

  -Microsoft Virtual Wifi Mini Port adapater #2

  -Realtek PCIe GBE family controller.

  #2 of the one is double and maybe causing the problem.

  As far as I know I thought that this model only required of these network drivers:

  -Intel Wireless driver for microsoft Windows 7

  -realtek LAN Driver

  -intel Pro set bluetooth driver

  Would be great for someone could confirm. Don't know how to move forward with this? Download the necessary drivers while that uninstall the old drivers? If so which ones should be deleted, guessing each of them?

  Mean time tried to hell be able to save, not much success. To be honest after noticing these adapters, it immediately at odds with what I knew and was informed months ago I wanted so just clear it first with you guys.

  Hello:

  I just checked my laptop which also has an Intel wireless card and it has the same features listed.

  Microsoft Virtual Wifi Mini Port card

  Map Microsoft Virtual Wifi Mini Port #2

  So I would say to both of them, because my laptop has no problems with the connection and maintaining a connection to the internet.

  Have you tried the latest driver for this model directly from Intel wireless card?

  It would be the only suggestion I can offer you.

  You want the second pilot on the list for W7 x 64.

  https://downloadcenter.intel.com/download/23723/Intel-PROSet-Wireless-Software-and-Drivers-for-Windows-7-