Doubt on the RA aaa using ACS 5.3 vpn user

Similar Questions

• Question about ACL's with the 2621 when using site to site VPN

  I set up two site to site vpn. We have an ASA at our headquarters and branches will IOS routers - one is a 1811 and the other 2621. Both are running the latest versions of IOS, respectively. The two VPN site-to-site do not work. I have a list of inbound on the external interfaces of both routers, access that allows only the IP address of the ASA IP traffic. All other traffic is denied. I put NAT overload upward in the typical form, and I use ip outgoing inspection on the same interface, to allow incoming traffic back to surfing the internet. This configuration works very well with the 1811, where all traffic is blocked except traffic IP (IPSEC) coming from the ASA. Guests at our headquarters can reach hosts behind the 1811 and vice versa.

  Here's my problem: the 2621 is processing traffic encapsulated on the external interface and block this traffic because it does not match. I know because when I turn on logging / debugging on the 2621, I see inbound traffic blocked by the ACL. Technically, I guess that it does not, but to this interface, the traffic is always encapsulated so I think it fits to this access list and then go to the Cryptography decapsulation card and be sent to the destination host. Just as it does on the 1811. I have not 'wan' t to create another line in the access list for all subnets to Headquarters. Why is not it works the same way as it does on the 1811? Is there something else I need to activate?

  ------------------------------------------------------------------------

  Config of 1811:

  !
  version 12.4
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-timezone msec
  encryption password service
  !
  hostname BranchVPN1
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 51200 notifications
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  activate the default AAA authentication no
  authorization AAA console
  AAA authorization exec default local
  !
  AAA - the id of the joint session
  no ip source route
  IP cef
  !
  !
  IP inspect the audit trail
  inspect the IP dns-timeout 10
  inspect the name IP internet udp timeout 30
  inspect the name IP internet tcp timeout 30
  inspect the name IP internet ftp timeout 30
  inspect the name IP internet http timeout 30
  inspect the name firewall tcp IP
  inspect the name IP firewall udp
  inspect the name IP firewall icmp
  IP inspect the dns name of the firewall
  inspect the name IP firewall ftp
  inspect the name IP firewall http
  inspect the name IP firewall https
  inspect the IP firewall name ftps
  property intellectual auth-proxy max-nodata-& 3
  property intellectual admission max-nodata-& 3
  !
  !
  IP domain name xxxx
  !
  !
  !
  !
  username xxxxxxxxxx
  !
  !
  !
  class-map correspondence vpn_traffic
  police name of group-access game
  !
  !
  VPN policy-map
  class vpn_traffic
  in line-action police 2000000 37500 pass drop exceeds-action
  !
  !
  !
  crypto ISAKMP policy 10
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key address xxxx xxxxxx
  ISAKMP crypto keepalive 10
  !
  life crypto ipsec security association seconds 28800
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac xxtransform
  !
  xxmap 10 ipsec-isakmp crypto map
  defined peer xxxx
  Set transform-set xxtransform
  PFS group2 Set
  match the address tunnelnetworks
  static inverse-road
  !
  !
  !
  interface Loopback0
  172.16.99.1 the IP 255.255.255.255
  !
  interface FastEthernet0/0
  Description Connection to Internet (DHCP)
  DHCP IP address
  IP access-group outside_in in
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  inspect the firewall on IP
  NAT outside IP
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No cdp enable
  xxmap card crypto
  !
  interface FastEthernet0/1
  Description of the connection to the local network
  address 172.20.1.1 IP 255.255.255.0
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No cdp enable
  VPN service-policy input
  !
  interface Serial0/0/0
  no ip address
  Shutdown
  No cdp enable
  !
  interface Serial0/1/0
  no ip address
  Shutdown
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 dhcp
  !
  no ip address of the http server
  local IP http authentication
  no ip http secure server
  IP nat inside source list nat - acl interface FastEthernet0/0 overload
  !
  IP nat - acl extended access list
  refuse any 10.0.0.0 0.255.255.255 ip
  allow an ip
  outside_in extended IP access list
  allow udp any eq bootps host 255.255.255.255 eq bootpc
  allow an ip host (ASA IPADDR)
  deny ip any any newspaper
  IP extended access list police
  deny ip host xxxx any
  deny ip any host xxxx
  IP 172.20.1.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  tunnelnetworks extended IP access list
  permit host 172.16.99.1 ip 10.0.0.0 0.255.255.255
  IP 172.20.1.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  !
  recording of debug trap
  logging source-interface Loopback0
  exploitation forest xxxx
  access-list 160 note t is
  not run cdp
  !
  !
  control plan
  !
  Banner motd ^ CC

  Authorized technician!

  ^ C
  !
  Line con 0
  line to 0
  line vty 0 4
  exec-timeout 5 0
  Synchronous recording
  entry ssh transport
  line vty 5 15
  exec-timeout 5 0
  Synchronous recording
  entry ssh transport
  !
  Scheduler allocate 20000 1000
  end

  ------------------------------------------------------------------------

  2621 Config:

  !
  version 12.3
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-timezone msec
  encryption password service
  !
  hostname BranchVPN2
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 51200 notifications
  no console logging
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  activate the default AAA authentication no
  authorization AAA console
  AAA authorization exec default local
  AAA - the id of the joint session
  IP subnet zero
  no ip source route
  IP cef
  !
  !
  IP domain name xxxx
  !
  IP inspect the audit trail
  inspect the IP dns-timeout 10
  inspect the name IP internet udp timeout 30
  inspect the name IP internet tcp timeout 30
  inspect the name IP internet ftp timeout 30
  inspect the name IP internet http timeout 30
  inspect the name firewall tcp IP
  inspect the name IP firewall udp
  inspect the name IP firewall icmp
  inspect the name IP firewall ftp
  inspect the name IP firewall http
  Max-events of po verification IP 100
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  username xxxxxxxxxxxx
  !
  !
  !
  class-map correspondence vpn_traffic
  police name of group-access game
  !
  !
  VPN policy-map
  class vpn_traffic
  in line-action police 2000000 37500 pass drop exceeds-action
  !
  !
  !
  crypto ISAKMP policy 10
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key address xxxx xxxxx
  ISAKMP crypto keepalive 10
  !
  life crypto ipsec security association seconds 28800
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac xxtransform
  !
  xxmap 10 ipsec-isakmp crypto map
  defined peer xxxx
  Set transform-set xxtransform
  PFS group2 Set
  match the address tunnelnetworks
  reverse-road remote-peer
  !
  !
  !
  !
  interface Loopback0
  172.16.99.2 the IP 255.255.255.255
  !
  interface FastEthernet0/0
  Description Connection to Internet (DHCP)
  DHCP IP address
  IP access-group outside_in in
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  inspect the firewall on IP
  automatic duplex
  automatic speed
  No cdp enable
  xxmap card crypto
  !
  interface Serial0/0
  no ip address
  Shutdown
  No cdp enable
  !
  interface FastEthernet0/1
  Description of the connection to the local network
  IP 172.20.2.1 255.255.255.0
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  automatic duplex
  automatic speed
  No cdp enable
  VPN service-policy input
  !
  interface Serial0/1
  no ip address
  Shutdown
  No cdp enable
  !
  IP nat inside source list nat - acl interface FastEthernet0/0 overload
  no ip address of the http server
  local IP http authentication
  no ip http secure server
  IP classless
  IP route 0.0.0.0 0.0.0.0 dhcp
  !
  !
  !
  IP nat - acl extended access list
  refuse any 10.0.0.0 0.255.255.255 ip
  allow an ip
  outside_in extended IP access list
  allow udp any eq bootps host 255.255.255.255 eq bootpc
  allow an ip host (ASA IPADDR)
  deny ip any any newspaper
  IP extended access list police
  deny ip host xxxx any
  deny ip any host xxxx
  IP 172.20.2.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  tunnelnetworks extended IP access list
  permit host 172.16.99.2 ip 10.0.0.0 0.255.255.255
  IP 172.20.2.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  recording of debug trap
  logging source-interface Loopback0
  exploitation forest xxxx
  not run cdp
  !
  !
  !
  !
  !
  Banner motd ^ CCC

  Authorized technician!

  ^ C
  !
  Line con 0
  line to 0
  line vty 0 4
  exec-timeout 5 0
  Synchronous recording
  entry ssh transport
  line vty 5 15
  exec-timeout 5 0
  Synchronous recording
  entry ssh transport
  !
  !
  end

  Please check if this helps:

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_crpks.html

  Federico.

• How can I assign the static fixed IP for remote access VPN users

  Hi team,

  I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this

  Thanks in advance
  Mikael

  username user1 attributes

  VPN-framed-ip-address 10.200.115.78 255.255.0.0

• How to check the total memory used by Oracle and user who use more memo

  Hello
  
  I use oracle 10.2.0.4 on Windows 2003 server SP2 version.
  
  1. How can I check the "total memory" used by Oracle
  
  2. which users use more CPU resources.
  
  Thanks and greetings
  Amit

  Hello

  Oracle EM is the best to identify the use of the processor and memory used by each session.

  In addition, use after query to calculate the memory used by each session of the.

  SELECT to_char (ssn.sid, '9999') | ' - ' || NVL (ssn.username, nvl (bgp.name, 'background')) |
  NVL (Lower (SSN.machine), ins.host_name) "SESSION."
  TO_CHAR (prc.spid, '999999999') ' PID/THREAD. "
  TO_CHAR ((se1.value/1024) / 1024, '999G999G990D00'). "MO" "SIZE."
  TO_CHAR ((se2.value/1024) / 1024, '999G999G990D00'). "MO" 'MAXIMUM SIZE '.
  V $ sesstat se1, v$ sesstat se2, v$ session ssn, v$ bgprocess bgp, v$ process RPC.
  v$ ins instance, v$ statname stat1, v$ statname stat2
  WHERE se1.statistic # = stat1.statistic # and stat1.name = 'pga session in memory.
  AND se2.statistic # = stat2.statistic # and stat2.name = 'pga memory max session'
  AND se1.sid = ssn.sid
  AND se2.sid = ssn.sid
  AND ssn.paddr = bgp.paddr (+)
  AND ssn.paddr = prc.addr (+);

  Kind regards
  Charrier

• Unable to switch to the privilege level using password set using ACS enable

  Hi all

  I am not able to not be able to visit the privilege level to help enable password set using ACS 1121 (5.4.0.46).

  Please find details of the ASA-

  ASA5580-20
  version of the software - 9.1

  LAB - FW / see the law # run | I have aaa
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + (inside) host 192.168.x.x
  GANYMEDE + LOCAL console for AAA of http authentication
  Console telnet authentication GANYMEDE + LOCAL AAA
  AAA authentication enable console LOCAL + GANYMEDE
  authentication AAA ssh console GANYMEDE + LOCAL
  Console telnet accounting AAA GANYMEDE +.
  AAA accounting console GANYMEDE + ssh
  AAA accounting enable console GANYMEDE +.
  No vpn-addr-assign aaa

  I created the Shell profile so & given privilege 15 it.please find wink 1 similarly in word doc attached

  However, when I try to create the service profile I get the error message, please find snap 2 in word doc attached.

  Kindly share your expertise.

  Hello Dominic,.

  For authorization privileges to take effect, you must add the following command to your configuration on the ASA:

  AAA authorization exec-authentication server

  After adding it, the ASA will take into account the level of privilege that are sent by the ACS.

  Associated with the error you are getting on the graphical interface of the ACS, please make sure that you are using a browser supported for ACS 5.4 version based on the release notes:

  http://www.Cisco.com/c/en/us/TD/docs/net_mgmt/cisco_secure_access_contro...

  Note: Please mark it as answered as appropriate.

• Anyone know of a doc covering using ACS 5.3 to control the VLAN using GANYMEDE?

  Hello

  If someone could help with this, I'd appreciate it.

  I configured a system ACS 5.3 and all my groups etc fucniton corrcetly both for network access and for the Administration of the unit.

  However I am stuck trying to allow clients to authenticate on the page web of the router or the Web authentication, using GANYMEDE + between the router and the ACS5.3.

  I watched this and I need to configure a custom attribute of 'service' with the type bound and in relation to a permission policy.

  I think that the custom configuration attributes is where I'm stuck.

  Once agin thanks for any help

  Brian

  Your best bet is to use the RADIUS, ACS supports RADIUS and most of the time you try to users access to the network of your admins of device segment, and the best way to do that is using RADIUS versus Ganymede.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• doubts in the database using backup controlfile recovery.

  Hi gurus,

  I have a doubt in database recovery using backup controlfile.

  I do not speak of "ORA-01207: file is newer than the control file - old control file.

  Here, any of our files archive / redo log have been lost and the problem of lack of update in the control file.

  So why open the database in resetlogs option, after recovering the database by using a backup controlfile. ?

  Thanks in advance

  Mahi

  In order to maintain the consistency of the data, the RCS should be the same in all the files of the controlfile & file REDO data current.

  By definition when you use 'backup controlfile' there a SNA expired in it.

  RESETLOG requires the RCS to 1 in order to get consistency across all files in the database.

  CREATE CONTROLFILE fills this new file with the most recent SNA that exist in the data files.

  It's just the way Oracle has been implemented.

• doubt in the use of multi canvas [SOLVED]

  Hi people,
  
  I use forms 6i with oracle 9i. I had basic doubts on canvas.that is assumed if we create multicanvas to display a special canvas, we can use TAB option.rather can we use any encoding to display a specific canvas?. If yes how to write code in which trigger?
  
  and a probably more if I have multi data blocks and if I create a canvas for ex, there is a datablock BLOCK3.now to know if I create a canvas CANVAS7 know how to locate this particular painting in datablock BLOCK3.
  pls suggest me.thanku in advance.
  
  Concerning
  VIDS
  
  Published by: vidusnat on June 29, 2009 12:29 AM

  Hi Vidusnat,

  You create a canvas in a window and then data block in your Web.

  So, when you create the data block, go in the layout editor, you will see the canvas and the block over the drawing area.

  Select the appropriate (in this case CANVAS7) canvas where want you place your block.

  You can explicitly set the scroll bar canvas to the property 'CANVAS7' (in this case) in the property for BLOCK10 palette window.

  It will be useful.

  Check the answer as useful / OK, if this can help you

  Carole

  Published by: Carole Punj on June 29, 2009 00:17

• Permission of AAA with ACS Shell-games

  Hi all

  I use a router cisco 871 running that version 12.4 (11) T advanced IP Services.

  I have difficulty getting permission to AAA to work properly with ACS.

  I am able to configure ACS fine users and assign them shell and private level 7.

  I then install a set of Shell Auth and enter the issuance of orders and configure.

  When I log in as a user, I get an exec with a level of 7 priv no problem, but I never seem to be able to

  to access global configuration mode by typing in conf (or set up) terminal or t.

  If I type con? It is the only command connect, configure is never an option...

  The only way I can get this to work is by entering the command:

  privilege exec level 7 Configure terminal

  I thought the whole purpose of the ACS Shell Set to provide this information to the router?

  It's frustrating

  The ACS server is set up with the Shell Set named Level_7 order authorization

  It is attributed to the relevant groups and I have the 'Unmatched orders' option selected in the 'license '.

  The "unmatched Args allowed" is also selected.

  See an extract of my IOS config below:

  AAA new-model

  !

  !

  AAA group Ganymede Server + ACS

  Server 10.90.0.11

  !

  AAA authentication login default group local ACS

  AAA authorization exec default group ACS

  AAA authorization commands 7 by default local ACS group

  !

  Cisco radius-server host 10.90.0.11 keys

  !

  !

  privilege exec level 7 Configure terminal

  privilege exec level 7 set up

  privilege exec level 7 show running-config

  privileges exec level 7 show

  !

  Hope you can help me with this one...

  PS I tried with orders of privilege on the router and remove the router and just keep getting the same results!

  Hello

  So now,

  You're actually using two different options and trying to couple then together. What I would say is you either use authorization Command Shell function or play with level privileges. Not mixed together both.

  Above scenario might work, if you move orders to focus on level 6 and give the 7 user privilege level. He couldn't be sure. Try it and share the results.

  That's what I suggest that orders back to a normal level.

  Provided below are the steps to set up the shell command authorization:

  -------------------------------------------

  Follow these steps on the router:

  -------------------------------------------

  ! - is the desired username

  ! - is the password

  ! create - us a local user name and password

  ! - in case we are not able to get authenticated via

  ! - our Ganymede server +. To provide a backdoor.

  password username 15 privilege

  ! - To apply the aaa on the router model

  AAA new-model

  ! - Following command is to specify our ACS

  ! - location of the server, where is the

  ! - ip address of the ACS server. And

  ! - is the key which must be the same during the FAC and the router.

  radius-server host key

  ! - To get the authentication of users through ACS, when they try to log - in

  ! - If our router is unable to join the ACS, we will use

  ! - our local user name & the password that we created above. This

  ! - we prevent locking.

  AAA authentication login default group Ganymede + local

  AAA authorization exec default group Ganymede + local

  AAA authorization config-commands

  AAA authorization commands 0 default group Ganymede + local

  AAA authorization commands 1 default group Ganymede + local

  AAA authorization commands 15 default group Ganymede + local

  ! - Sequence of commands are for posting to the activity of the user.

  ! - When the user connects to the device.

  AAA accounting exec default start-stop Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  orders accounting AAA 0 arrhythmic default group Ganymede +.

  orders accounting AAA 1 by default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  --------------------

  ACS configuration

  --------------------

  [1] Goto 'Profile components shared' a-> 'Shell command authorization sets'-> 'Add '.

  Provide any name at all.

  provide sufficient description (if necessary)

  (a) for full administrative access set.

  In the unmatched controls, select 'allow '.

  (b) for all access limited.

  In the unmatched controls, select "decline."

  And in the field above 'Add a command' box, type in the box below and the main command "permit unmatched Args" Order under allow.

  For example: If we want the user to only have access to the following commads:

  opening of session

  Logout

  output

  Enable

  Disable

  Show

  Then, the configuration should be:

  -----------------------------------------------

  -Allowed unparalleled Args.

  -----------------------------------------------

  connection permit

  permit disconnection

  exit permits

  Select the permit

  disable the permit

  license terminal configuration

  ethernet interface license

  permits 0

  to see the running-config

  ------------------------------------------------

  in example above, user will be allowed to run only from commands. If the user tries to run the interface ethernet 1', the user will get "failed command authorization.

  [2] press 'submit '.

  [3] Goto Group on which we want to apply these command authorization set. Select 'change settings '.

  (more...)

• ACS database does not not after having changed the secondary ip of acs.

  Hello.. Im having 2 ACS 3.1 server. ACS01 (primary) & ACS02 (secondary). We recently moved ACS02 to another site and has changed its ip address.

  When we of database replication from ACS01, we received the error message saying ACS02 has refused the request of replication.

  Any idea what can be the problem?

  Consider these elements when you implement the database replication feature Cisco Secure:

  (1) ACS supports only supported replication of database to other ACS servers. All ACS servers participating in the Cisco Secure database replication must run the same version and patch to FAC level.

  (2) the principal server copy compressed and encrypted the database on the secondary server components. This transmission is done via a connection TCP, Port 2000. The TCP session is authenticated and using an encrypted protocol, Cisco-owners.

  (3) only hosts properly configured, valid ACS can be secondary servers. To add a secondary server, configure it in the AAA servers table in the section of this document Network Configuration. When a server is added to the AAA servers table, the server is displayed for selection as a secondary server in the list of AAA servers as replication partners, on the Cisco Secure database replication page.

  (4) the principal server must be configured as an AAA server and must have a key. The secondary server must have a primary server configured as an AAA server and its key for the primary server must match the key primary servers.

  (5) secondary servers replication takes place sequentially in the order listed in the replication list under replication partners, on the Cisco Secure database replication page. (6) the secondary server that receives the replicated components must be configured to accept replication of database from the primary server. To configure a secondary server for database replication, refer to configuring a secondary Cisco Secure ACS Server of this document section.

  (7) ACS does not support two-way replication of database. The secondary server, which receives the replicated components, check that the primary server is not on its list of replication. If this is not the case, the secondary server accepts replicated components. If so, it rejects the components.

  (8) to replicate the seller of RADIUS defined by the user and the configurations of the specific attribute (VSA) provider successfully, definitions have to be replicated must be identical on the primary and secondary servers. This includes seller RADIUS slots occupy sellers RADIUS defined by the user. For more information on the sellers of the RADIUS and the VSA attributes defined by the user, see section User-Defined RADIUS vendors and VSA sets the document Cisco Secure ACS database command-line Utility.

• AAA using microsoft IAS

  Hi all

  I'm looking for a little guidance. Aplogies if I'm not following the correct procedure, but I am a newbie to SCC so feel free to let me know if I'm not posting my question correctly. I'm a network administrator for a medium-sized company, running a variety of Cisco devices. Currently, all we have is authentication password user name local on the devices.

  I was in charge so that we can control who gets access to devices, what level of access they get to come up with a solution of AAA and logging of the business and ofwhat they played. In the current climate, we will not get the money to buy ACS or something similar, so my question is this.

  Can Microsoft Server IAS (Internet Authentication) provide me with a decent solution of AAA?

  What I really want to do is to allow network administrators full access to devices (privilege 15) and personal help desk some cut to the low level of access (still to be defined) with authentication that occur by using the Acive directory.

  From what I read the part of Authencation isn't too hard, but I want to connect in the authorization and accounting in the solution.

  Can someone give me a starting point or benefit from their experience?

  Thank you very much

  Tom

  Hi, Tom.

  IAS can be used. There are number of threads on the forums of the SCC on AAA on IAS.

  But IMHO, if the Cisco products are not an option because of the money, better turn to FreeRADIUS.

  If your bosses are still considering the budget, you can try the evaluation version of ACS (all features, free) and if you're going to love it - try to convince them to buy a normal.

  Also, you can watch ACS Express - it must also meet your needs.

  Cheers, iron

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• How can I fix the redirects when using Firefox 30? Windows 8.1.

  I've redirected and/or pop ups using Firefox 30 with Windows 8.1. He started immediately with the download of the said Windows 8.1, so I think it came with this download, and although I have run deep scans and even a pre-start with Avast scan, as well as a scan with IObit Anti Malware, I always get the redirects or pop ups.

  A smart redirection (context sensitive) it's trying to get the money from you. For example, I had tried to stop the pop ups [redirects, maybe] with the pop-up blocker probably integrated into Firefox, but Firefox Help leads me to an # 800 who offered to connect remotely and fix my PC with certified technicians as you will see in the chat below. He appeared as a function of Firefox, not a redirect.

  Just after the chat with the 800 suit, I opened FireFox and he went to the (default) url: start.mysearchdial.com/ and a hash string more, which is perhaps how popups spreads?
  I'm from mozilla via a url and soon encouraged me to download the new version, saying a current obsolete. But he was not going to download it from: http://downloadsoftware.pw/download/firefox2/

  He isn't very smart, it is also resistant to many software removal tools.

  What could suggest you? I tried not many of these tools yet.

  MySearchDial must have an entry in the Control Panel, but may also have fangs in your browsers.

  Control and cleanup that will take a few precautions. I suggest starting here:

  Open the Control Panel, uninstall a program. Click on the column heading "installed on" to group infections, I mean additions by date. This can help the undisclosed items bundle smoker who snuck out with some software, you have agreed to install. Out as much garbage as possible here.

  Then, in Firefox, open the page modules using either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then, in case of doubt, disable (or delete, if possible) not recognized and unwanted extensions.

  Often, a link will appear above at least an extension disabled to restart Firefox. You can complete your work on the tab and click one of the links in the last step.

  Finally, you can "absorb" remain problems with the scanning/cleaning tools listed in our support article: Troubleshooting Firefox problems caused by malware.

  Are you able to get rid of him?

• Computer laptop HP DV6 freezes when on the power of the battery, for the most part using Firefox. Looking for help in debugging

  Is there anywhere I can look to see what is running or happening when my PC crashes?

  BACKGROUND:

  My PC has been freezing more frequently lately.

  It seems to happen more often when I am on battery, usually when I am online using Firefox my default browser.

  I tried checking the event viewer, but did not find much, and do not know, I am interested in the right part.

  I can say without a doubt it happens when it is on battery power, almost never when it is plugged.

  In addition, it seems to happen more frequently when I use Firefox, but then I'm usually just surf when I'm on battery.  When I don't really work, I tend to sit at a desk and connect.

  Here are my specs:

  HP Pavilion dv6-3120us laptop

  Product number: XG871UA

  OS: Windows Home Premium Service Pack 1

  Browser: Firefox Chrome for the most part, other times

  I'm starting to capture when / where it happens the more frequntly in a strive to locate the problem.

  I'll try to turn off Firefox addins / extensions as a first step, but would like any other tips.

  Thank you!
  Ian

  I did a quick check this week, surfing on the battery while using Firefox, I fell two times.  Once run it normally, first with all add-ons disabled.

  When I switched to Chrome I had any problems.

  I'll close this and call it a problem of Firefox, I'll open a new ticket if it appears elsewhere.

  But I'll check the both battery test.

  Thank you!
  Ian

• Limiting the tables and using lindex in commands regexp

  Hello

  Here's my second and extremely crap question/post in what concerns the EEM/TCL.  I did some research on Google and have not really been able to find an answer to these questions.  Probably more due to my lack of agility with the search bar of the information being just is not there.  Hope you'll forgive me if.

  1. my first question is this.  Say I want to get an output of a command.  I would like to see all the interfaces in the 'ip vrf command show interface' for example.  Not knowing how many interfaces there may be, there could be 10, or there might be 200, what is the best way to limit a loop function after that I gave the following commands?

  Set _vrf_int [exec show ip vrf interface]
  Set _array_vrf_int [split $_vrf_int '\n']

  set $i 0

  then {$i< 200}="">
  RegExp {([A-Z]+[a-z]+[0-9]+). *} [lindex $_array_vrf_int $i] _complete_string _int
  Inc. $i 1

  }

  Not 100% sure that the syntax is correct, sorry.  If I don't have that 10 interfaces so it won't be necessary to issue this loop 200 times to "$_array_vrf_int".  Also wouldn't be great if I went through the 200 interfaces.  Is there a way I can limit this loop based on the number of lines that were captured after the split function?

  2. the value of the regular expression above is output in the var $_int.  Is there a way I can output the regular expression in a table? a ' :-

  RegExp {([A-Z]+[a-z]+[0-9]+). *} [lindex $_array_vrf_int $i] _complete_string [lindex $ $i _int]

  Syntax is certainly not correct, but I guess there could be a way to do this.  Any thoughts?

  3. I did some comparisons on an outing to see if an access list is present on an interface.  I can get a regexp to pull back the name of the access on a given interface list, but if there are any access-list to an if statement on anything?

  Set _acl_name 0

  RegExp {. * ip access-group (. *) in} $_running_int _complete_string _acl_name

  If {$_acl_name! = 0} {puts ' there is an access-list on $_int "} else {puts ' there is no acl on _int $ :-("} "}

  In the above output I'm defining the value of ' $_acl_name ' to zero so that I can compare it to the fi statement.  This seems to be a newbie to shit how do however.  Is it a kind of generic I put in place of the '0' to match an empty variable. has ' {null}.

  4 I'm sorry last question.  I also reset the variable {null} using a similar wildcard.  Once again I can reset the variable to 0, but it seems just that I do not understand that the syntax well enough and it is without doubt a better method.

  5. I have read several tutorials that cover a lot of bases.  Is there a good reference that anyone can suggest so I don't waste your time with these silly questions?  I'm afraid that the scripts I've studied on this forum are always way above my head.

  Thanks in advance

  Alex

  Assume that the limit of the loop.  Which will never end well.  Instead, use a foreach loop to iterate over the number of lines in the output:

  set vrf_int [exec "show ip vrf interface"]
  foreach line [split $vrf_int "\n"] {
  
        if { [regexp {([A-Za-z0-9]+).*} $line -> int_name] } {
  puts "Interface name is $int_name"
  }
  }
  

  In addition, do not use the variables that start with "_".  Those that are reserved for the Cisco or overall use.  In addition, 'exec' is a single command tclsh.  If you use the EEM Tcl, you will need to interact with the CLI library.  You can watch our best practices guide at https://supportforums.cisco.com/docs/DOC-12757 for some tips and tricks with the use of EEM.

  You can use - all and--inline for regexp all return in a list.  However, given the idea of the loop above, you can also use lappend to each pass:

  set intlst [regexp -all -inline {([A-Za-z0-9]+).*} $output]

  
  set vrf_int [exec "show ip vrf interface"]
  set intlst [list]
  foreach line [split $vrf_int "\n"] {
  
        if { [regexp {([A-Za-z0-9]+).*} $line -> int_name] } {
  lappend intlst $int_name
  }
  }
  
  
  
  You can use "info exist" or simply to check the result of your regexp command to see if a match took place.  See the example above the latter.
  regexp {.*ip access-group (.*) in} $_running_int _complete_string _acl_name
  if {[info exists $_acl_name]} {puts "there is a access-list on $_int"} else {puts "there's no acl on $_int :-("}
  
  You can 'reset' a variable by using the command 'deactivated '.
  One of the best general Tcl references is the "book of the pen:
  
  http://www.Amazon.com/practical-programming-Tcl-4th-Edition/DP/0130385603/ref=sr_1_2?ie=UTF8&QID=1333817448&SR=8-2
  		   

• doubt to the wi - fi connection

  Hello

  I have a doubt about the WiFi with a device.  I have this in my source code:

     String URL = urlupdate + ";interface=wifi";
                         conn = (HttpConnection)Connector.open(URL);
                         //
                        int rc = conn.getResponseCode();
                         if (rc != HttpConnection.HTTP_OK)
                             throw new IOException("Error response code: " + rc);
                         is = conn.openInputStream();
  

  and his works in my Simulator. But the doubt is when I use the phone, do I have to change the source code with all the settings?

  Thank you

  Assuming that the device has WiFi and it works, so this code should run as is, on the device.