Drive of DVD in UCS C210 M2 Server does not

Similar Questions

• Drive CD/DVD internal L50-B-1VE satellite does not

  I have the following Satellite L50-B-1VE, problem updated to win10: I cannot mount DVD/Cd on my player. Using an external drive, it works. He used to work after upgrade win10.
  I tried uninstalling the driver, the IDE controller, removing lowfilters in regedit (there is only anydvd) without success.

  So there is doubt on the presence of a hw problem, I want to make sure of before you send it to a repair centre.

  I tried with a picture of relief without success (unfortunately not enough - old problem is still there). I have also generated victory 8.1 recovery disk.

  Here's what I think to move forward (alternatives):

  1. Doing a full backup to a drive ext, reset the PC to the factory (it will be 8.1), test pilot and restore using system restore
  2. Start Advanced 8.1 drive, check if at least one DVD can be read, he quit and restart normally.

  Those above allows to be sure of the nature of the question?

  My questions:

  • Clearly the 2. Looks the less time-consuming. Can I assume that the driver is loaded to play the DVD are the factory ones? Is my configuration of win 10 preserved, so that I can avoid backup?
  • 2 is also the procedure I need to follow before you send the laptop to repair. In any case:
    • Any problem to recover an image to win 10 in a win environment 8.1?
    • I noticed that some programs use c: route to store their data (one of them is relevant to my tax data). Are these directories held by backup or manually register the)

  Thanking in advance suggestions/answers

  My question is how do I roll back for CDs of native drivers set up so I can tell if it's a hardware or a sw problem?

• HL-DT-ST DVD-RAM GH40L SCSI CdRom Device does not work code 32

  HL-DT-ST DVD-RAM GH40L SCSI CdRom Device does not work Code 32

  The other post:

  HL-DT-ST DVD-RAM GH40L SCSI CdRom Device does not work, another driver can provide this functionality. (Code 32)

  Hello

  1 are there any changes or updates made on the computer?

  2. when exactly you get the error message?

  Code 32: a driver (service) for this device has been disabled. Another driver can provide this functionality.

  I suggest to return the item and try to run the fix it and check if it helps.

  Your CD or DVD drive cannot read or write media

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Let us know if it helps.

• Hi, my DVD MATSHITA DVD - RAM UJ 875 S ATA does not work

  Even I am facing the same problem.

  I have a lenovo y410 laptop. my DVD MATSHITA DVD - RAM UJ 875 S ATA does not work... it is not reading all discs... not to burn all...

  When the problem occurred I immediately called the customer... but as the phones warranty period I can replaced also do it... Please help me with a solution...

  This is what happens when I insert a disc in the drive... the led flashes for a few seconds... the disc seems to move but then the led stops blinking and nothing happens...

  I have tried both what is the necessary changes in the REGISTRY & also uninstalled the software and restarted my laptop. But the problem is still there.

  Please let know me of any other way to solve this problem

  Hello
  
  I suggest you run the fixit and see if it helps:
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  It will be useful.

• To install the server does not, after a Preparig to install the window hung for several minutes

  Hi, I tried to install memeo backup of a product for a moment, I recentley purchased. I know that the software and the product is not damaged, because I am able to install it on other computers. Its my fault see tho, I have the seagate FreeAgent GoFlex 1 TB external hard drive, and I had planned to use it on several computers. sort of, I installed it on my computer windows 7 without probs., but when I was installing on my windows vista computer, I accidentally unplugged the drive when installing memeo instant upward.  Needless to say, I knew this would be a problem. Windows popped up saying that the dashboard Seagate (which is the program that installs Memeo instant backup) have not installed properly, so I clicked on reinstall this program with the recommended settings, and I handed the drive and started the installation again. When I did, the registration page (for the unit I was using) pops up and froze, so I closed its process, then Setup of the Board of Directors of Seagate Dash appeared and I started to install, and when he rose to installation of the snapshot of Memeo back, it opens a "Preparing to install" window of a windows installer and after about 10-15 minutes , another windows installer window comes up saying ' to install the server does not.

  Ive done my time just trying to solve this problem and believe he made an incomplete registry file, it whenever it tries to install it tries to use the incomplete record. If one has found a solution to this, or knows what that means of ' installation server does not ", it would be very appreciated for your advice.    If you want to know my characteristics. they are {windows vista 32-bit home Basic, sp 2, 3 GB of ram, 2.10 ghz processor}

  Hello

  you are in the wrong forum

  It comes to the installation of vista operating system instance

  Why don't contact you the program manufacturer?

  Try the repair and recovery forum

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system?page=1&tab=all

• Homer in Windows Server does not connect to the internet.

  I installed Windows Home Server on a self-built media server. Everything on the hardware is working properly. The server software is installed. The ethernet line is connected to my Linksys router. The power light is on decision-making on the case ethernet connection. The power led is on the router where the ethernet is connected. So, in my view, that the issue is not material.
  Problems:
  1. the server does not connect to the internet.
  2. my computer does not recognize the server when I install the Windows Home Server Connector software.
  3. the wizard of Linksys on my computer does not recognize the server as a "new device".

  I feel like I'm missing a driver, maybe a driver of ethernet controller, but do not know how to diagnose the problem.  I downloaded the Windows tool that identified the problems I listed, but solutions are not feasible.

  Any suggestions?

  Hi Mikey1947,

  You can check this link, try the suggestions provided and check if that helps

  http://social.Microsoft.com/forums/en-us/whsfaq/thread/15a9e657-54a3-453F-B0E7-1efa59b7feea

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Driver HP P1006 for windows 7 (32-bit) does not

  Hello. I have a problem with my P1006 printer. It works fine before with windows vista, but when I update windows 7 Professional last month. The printer does not work. I tried to download the driver for windows 7 using IE and Firefox. The driver does not work and the ftp server does not have this file

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-54963-5&LC=en&DLC=en&cc=us&...

  I chat with HP several times customer service and they give me the same link and its does not work and I did not help at all. They told me to try the next day and so on... I tried to download since the pilot was released until today, but his work much. I don't think that there is a problem with my computer (HP dv5-1000us) because I use the same laptop under vista and it works before. I also tried to download the file to my desktop still doesn't work. I hope someone could help me solve this problem. Thank you.

  Edit by Katie_H (30/03/11): fixing broken link

  Try this link, it replaces the ftp: / / with http://.  Some systems have settings that impede using ftp links.

  While calling fresh HP $$ when it is out of warranty, there are other methods of support that are free.  For some products of support is available by e-mail or chat.  And of course, there is always this forum, where other users can have an answer.

  Edit by Katie_H (30/03/11): fixing broken link

• Server does not start after the installation of the USB bootable, ESXi

  Hello

  I installed VMware ESXi 5 on a SSD drive using a bootable USB key, but my server does not automatically start since the SSD after installation. I can boot ESXi in the offered by the BIOS boot menu.

  The startup configuration is perhaps incorrect because during the installation of the USB drive is present, but after the installation, it is not?

  Also has anyone seen this problem?

  Kind regards

  Gijsbert

  Updating the BIOS on the DQ77MK at 49, and you should be able to start - UEFI must never be activated.

• Install Adobe Application Manager: "the remote server does not appropriately."

  I am running Windows 7 and have signed today for the trial of the creative cloud.  I am trying to download my first application (InDesign).  When you try to install Adobe Application Manager I download a 1866 KB file, then when I try to run it I get this error message (again and again, throughout the day): "the remote server does not properly.  Please try after a few minutes. »

  The only other things I can think of that may be relevant are 1) I have a few other licensed Adobe products installed on my drive (Photoshop, Illustrator, and Acrobat). (2) I have a few programs running, such as Spotify background; and (3) I have tried this for a work computer and I wonder if the network firewall or my permissions to download which is streaked with this place.

  Thanks for any help you can give.

  Nate_unhappycloudman this error has actually been resolved for countless people once their computer or the network is correctly configured.  We'll find a good starting point for possible causes on a computer at individual sign in or activation errors. CS6, CS5.5, Perpetual CS6 subscriptions - http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html.

  If your network is managed, please contact us and work with your I.T. Department as stated earlier in this thread.

• Server does not recognize my user name on outgoing emails

  On my iPhone 4 my server does not recognize my email (Telstra) address on outgoing emails, but recognizes the incoming emails. What happened all of a sudden no reason apparent. I have two other email addresses on the phone and they work fine. One is a gmail address and the other is another address of Telstra. Can someone help me please?

  try to remove the account from the problem and add it again

• El Capitan DNS server does not resolve host

  The server does not resolve host 'root '.

  I upgraded from an environment of Snow leopard server to the El Capitan 5.0.15 server.

  The server is running on a mac mini, which is now about 2 weeks old basis.

  Follow the instructions in the DNS settings. Hosts such as www.example.com work perfectly well.

  However, the server does not resolve example.com. On Snow Leopard server, I used to create records for hosts like example.com as www.example.com, but this seems to be not not more possible.

  Any idea?

  Thanks, XL

  to be more precise, that's what I get when a ping is made:

  Ping: impossible to solve example.com: Unknown host

• Server does not support remote façade panels

  Hello.  Hope someone has an idea about that.  After the computer host and update cDAQ 9139 LabView SP1 from 2013 to 2014 LabView dev suite shipped by NOR, I get the error "server does not support the remote panels" when you try to view my remote panel.  Before the update it worked normally.

  I went through everything in the list in this document, http://digital.ni.com/public.nsf/allkb/C23EF1551D8C52ED86256B140073EE2E and can't find anything that will solve the problem.

  I have rebuilt the application in 2014 of LabView (I even tried a new simple project with a single loop, one of the temperatures and a remote control), rebuilt the build spec and get the same error.

  "I've re-edited the web page and checked in the html code it refers"CODEBASE ="ftp://ftp.ni.com/support/labview/runtime/windows/2014/LVRTE2014min.exe" and I have, according to MAX, LabView DURATION 14.0.1 installed on the host machine.

  If something has changed related LabView 2014 which would cause a new firewall as this remote façade program worked great with 2013 installed?  I've already added that LabVIEW 2014 and all other related apps through the firewall, including the web server.  I am also on a machine that doesn't have a Bluecoat, our company network/internet security suite is installed.

  Thank you

  Michael

  Another possible solution to this problem - operator error.

  See one of my other posts here for details, but I made an assumption about the port numbers and what they apply to.  Two key points - the port of the web server application in the configuration of hardware web page is not the port used to access the remote panel - port is assigned in the properties of the device, the server settings remote control panel in the project.  And they cannot use the same port; This will also lead to the error "server does not support the remote panels.

  Note to the NOR - you must add this to your KB document on the resolution of this error.

  Thank you!

• Last night, I did a scan on my computer. He went only 3% when it froze with the server does not.

  Last night, I did a scan on my computer. He went only 3% when it froze with the server does not.

  Can you please explain the concept of what a server is and how can I ensure this does not happen.

  Thank you very much

  original title: Server

  Last night, I did a scan on my computer. He went only 3% when it froze with the server does not.

  Can you please explain the concept of what a server is and how can I ensure this does not happen.

  Thank you very much

  Launched a scan with which product (be specific, up to the exact version)?

  What version and architecture of Windows are you using?

• New domain today name ' hui - DNS server does not

  I'll put up a blog using WordPress software.  I recorded a doman name today and hired DreamHost to host the blog.  DreamHost successfully installed WordPress and sent me an email with a link to create an administrator. user.  When I click on the link, I get a message that the DNS server is not responding.  Verio, the company that has registered my domain name, also sent me an email with a link, I use to access my control panel.  I get the same message - DNS server does not respond.

  Because I only had access to the internet via a private with Rogers and used the e-mail account, I don't know I'm missing something simple... just do not know what.

  Please help beginners to blog!

  THX

  Ann

  Hello

  Like you are on a domain, your question would be better suited in the audience of IT professionals

  Please visit the link below to find a community that will support what ask you:
  http://social.technet.Microsoft.com/forums/en/category/w7itpro, windowsvistaitpro, windowsxpitpro, windowsintune

  Thank you

• I get an error "the server does not support an SSL connection" with a code of error 0x800CCC7D in Outlook express.

  I followed Bruce Hagen and still cannot send to the OE section. Reception is no problem. When I try to send I got the following error msg: "the server does not support an SSL connection. "Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, server response: ' 250 8BITMIME ', Port: 25, secure (SSL): Yes, Server error: 250, error number: 0x800CCC7D. I tried to change the port for outgoing to 456. When I do so I get this error msg: failed to connect to the server. Account: 'pop.att.yahoo.com', server: 'smtp.att.yahoo.com', Protocol: SMTP, Port: 456, secure (SSL): Yes, Socket error: 10060, error number: 0x800CCC0E.  Is there a cure for this. He just started two days or at least that's when I noticed I cud not send. If you can help me I will appreciate it more. Thank you.

  JP banks

  Original title: cannot send using OE 6. Reception Ok.

  Hi JPBANKS,

   

  Thanks for keeping us posted and share this information with us.

  Glad to know that the problem is solved. Do not hesitate to contact Microsoft Windows Forums for issues related to Windows in the future.