HL-DT-ST DVD-RAM GH40L SCSI CdRom Device does not work code 32

Similar Questions

• I have a HL-DT-ST DVD - RAM GH40L SCSI CdRom that do not work.

  I have a HL-DT-ST DVD - RAM GH40L SCSI CdRom that do not work. Device Manager indicates "a driver (service) for this device has been disabled. Now, the drive does not at all.  Any ideas on how to solve this problem? I can't get any DVD or CD to run on my PC now.

  Hello

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• CXUNG 4L6749Y7S SCSI CdRom Device does not work.

  CXUNG 4L6749Y7S SCSI CdRom Device does not work. My laptop cannot detect if I open and close the cd-rom.

  Original title: help please?

  Hi Jv Vailoxes,

  I suggest you to refer to the help article and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060/en-GB

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the registry in Windows:
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  It will be useful.

• HL-DT-ST DVDRAM GT32N SCSI CdRom Device does not work correctly

  Hello

  I have this unit in my ASUS laptop: HL-DT-ST DVDRAM GT32N SCSI CdRom Device,.

  and it is not read most of the inserted discs. Prints are better, but is not able to read one of my CDs or DVDs written at home.

  A few years ago I tried to solve the problem and that I can remember other users had the same problem and the driver update has been recommended, but I also discovered that the support for this product is complete, and I couldn't find all the archives. I dropped.

  Now I'm able to download a driver is already installed on the computer that has the version number: 6.1.7600.16385.

  I suppose that there could be problems other than the driver himself.

  Help, please!

  Hello

  Try to clean the disc with a cleaning disc.

  If cleaning doesn't help not the drive has a hardware problem, since it corresponds sporadically.
  For discs do you you try to use the format of the ISO image.

  Should which CD or DVD format I use?
  http://Windows.Microsoft.com/en-us/Windows7/which-CD-or-DVD-format-should-I-use

  =====================

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://Club.myce.com/F61/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Hi, my DVD MATSHITA DVD - RAM UJ 875 S ATA does not work

  Even I am facing the same problem.

  I have a lenovo y410 laptop. my DVD MATSHITA DVD - RAM UJ 875 S ATA does not work... it is not reading all discs... not to burn all...

  When the problem occurred I immediately called the customer... but as the phones warranty period I can replaced also do it... Please help me with a solution...

  This is what happens when I insert a disc in the drive... the led flashes for a few seconds... the disc seems to move but then the led stops blinking and nothing happens...

  I have tried both what is the necessary changes in the REGISTRY & also uninstalled the software and restarted my laptop. But the problem is still there.

  Please let know me of any other way to solve this problem

  Hello
  
  I suggest you run the fixit and see if it helps:
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  It will be useful.

• DVD-RAM on Qosmio G25 (AV513) does not work correctly

  Hi guys,.

  My G25 has crashed and I restored it using the original restore CD supplied with the machine, but after the installation of the DVD-ROM (Mat * a dvd - ram UJ-845 s) did not appear in the windows XP media center SP2 and in Device Manager.

  It appears with a yellow (!) I tried to install the driver on the site, but there are "device not connected".
  I tried the DVD via the Qosmio player and it worked does someone has an idea how make it work on windows again?

  Thank you

  Hey Buddy,

  have you tried to remove the drive from the "Device Manager" and reinstall completely? Normally windows should install then device and shouldn´t you need all the drivers, especially for the DVD-RAM.
  So, if it is not already done, remove it and try it.

  Greetings

• Carpet * a DVD - RAM in Satellite A100 drive does not work properly

  When I insert any type of disc, the drive lights up, but the system cannot access anything on the disc. I tried all the fixes that were shown in the forums, but nothing works. The message I get is: D: / is not accessible. I/o device error. Oddly enough the only disc it reads without any problems is the recovery disk. Unfortunately, a system recovery didn't solve the problem.

  Hello

  If you're still guaranteed then it would be necessary in your case bring/send your machine to a local toshiba for a hardwarecheckup servicepartner. But even if Don t you out of warranty you should do it because your questions sounds like a hardware failure.

  If you need help finding a service partner so I can give you a link where you can find one that is closest:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Good luck and good weekend
  Welcome them

• TSST DVD +-RW TS H653B ATA Device does not work

  I get the following error message

  Message: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)
  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I tried to reinstall the driver for the TSST DVD +-RW TS H653B with no luck.  I've also removed the device and close for the computer to recognize the device and he did, but impossible to install the driver.  I downloaded the lateest for the device driver with no luck either.  I also did a full stop, with drain power and pulled the plugs of the device and put them back in and have pulled up, still with no luck.  IM of ammunition at this stage.

  Hi Jmanjordan,

  You can try this step but, if that doesn't work then you may need to contact the manufacturer of the drive for further assistance. Open the link below and click the Fixit .

  http://support.Microsoft.com/kb/929461

  Bindu S -Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• My DVD player does not work and all the information I can find is "this device does not work correctly.

  Hi, I have Windows Vista and I use a computer laptop Dell studio. When I insert a disc into my CD/DVD drive, the drive spins and it looks like it is about to start and makes the same noise start several times and then just stops. My computer does not record that there is a disc there. If I double click on the DVD drive in 'My computer' it ejects my disc and says "insert the disc in drive E".

  I went on the 'repair' Microsoft online scanner and it told me that there is a problem, but he can fix it. In Device Manager, under CD/DVD-ROM readers I have Optiarc DVD +-RW AD - 7640S. Under device status - general - properties, it says "this device does not work correctly. He also says that I have the updated driver.

  I even uninstalled the driver as a last resort and then restarted my computer. It reinstalled the driver for me, but there was no change. Please help me!

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry
  entries that do not fix the resolution of problems and those who "could" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys in my opinion, are those in question - for the CD/DVD drive of course subkeys as
  There will be other subkeys in these keys. Do not forget to ask involved specific keys as well as the
  Parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Optiarc DVD RW AD - 7560A ATA DEVICE do not work

  My CD-ROM/DVD-ROM does not work.  Manager of devices display a "!" on the Optiarc DVD RW AD - 756 A ATA DEVICE.
  1 device state poster (this device cannot start. (code 10)).
  2 update driver... shows that the best device driver software is already installed.
  3. it is the driver of manufacturing.
  4 driver provider Microsoft Driver version - 6.0.601. 18000, manufacturer-(Standard CD-ROM drives)

  Hope that enough information... Oh, my computer is computer laptop Windows Vista Service Pack 1, Sony VAIO - VGN-NR22OE.

  Grateful for any advice...

  Hi Nikki 801,

  Can you please try these steps?  Be very careful when you edit the registry.  If you would please do not delete anything immediately.  If you must please the following steps... If upper and lower filters is not in this registry key, simply leave the registry.

  To resolve this problem, remove the affected filter drivers. To do this, follow these steps:

  1. Click Start
     Collapse this includes this image

     

     type regedit in the Search box, and then click regedit in the programs list.

     Collapse this includes this image

     

     If you are prompted for an administrator password or a confirmation, type your password, or click continue.

  2. Locate and then click the following registry subkey:
     HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

     Warning There may be many instances of the registry subkey that is mentioned in step 2. You must ensure that you are in the appropriate registry subkey before modifying the UpperFilters and LowerFilters values. To verify that you are in the appropriate registry subkey, make sure that the default data value is the CD-ROM/DVD-ROM and the class data value is CDROM.

  3. In the pane, click UpperFilters, and then click Remove.
  4. Click Yes to confirm the deletion of the UpperFilters registry entry.
  5. In the pane, click LowerFilters, and then click Remove.
  6. Click Yes to confirm the deletion of the LowerFilters registry entry.
  7. Exit the registry editor and restart the computer.

  If you please you would follow with me as best as possible, I'd be very happy.

  Thank you

  Aaron Griffin
  Support engineer
  Microsoft technical support

• On Satellite L500D DVD player does not work - Code 39

  my dvd driver does not work it says driver may be corrupted or missing (code 39) I got it 3 days new

  read here:

  http://APS2.toshiba-tro.de/KB0/TSB7801XL0000R01.htm

• Drive DVD/CD of Satellite a series does not work properly

  My computer sometimes starts fast and when it does recognize the DVD/CD player and functioning.
  However when she takes it the start time, it does not recognize that I have a DVD/CD player, when I look in Device Manager to see if
  There is no probs it simply says that the device is functioning properly?

  Does anyone has any ideas at all the

  Would be nice of you if you could give us MORE details; for example what operating system you have, what kind of machine you have and so on.

  It s hard to help someone, when that person said: my CD does not work, then it works then not again. It is not a description of the error.

  PLEASE MORE DETAILS

  THX

• Optiarc DVD RW AD - 7560A ATA device no longer works, "Code 19" referring to information from damaged or incomplete prevents widows to start this hardware device.

  Tried updated driver and the Microsoft Automated Troubleshooting service who could not solve the problem. If I put a disc in the DVD tray with the intention of reading, you can hear the disc for about 20-30 seconds then silence analysis. Never, AutoPlay opens the disc. Help!

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Please start from the top and do ALL this, although you could have done some before as is often the
  all operations which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. If the player does not then continue to the next step.

  Normally the above will solve this problem otherwise working your way down through them, even if you did
  them before.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Drive DVD Sony Vaio VGN - CR31S F: does not work

  Laptop is about 4-5 years, it was working fine until just recently, I tried to fix with Windows difficulty It Centre, but in vain. Drive (F) no longer recognizes no matter what media (CD of Scripture and other), or it will allow ripping/burning.  The drive from DVD (F) is an a Toshiba... If that's any help.

  Any ideas anyone?
  Thank you very much

  Hello

  Welcome to the Microsoft community.

  I see that you are facing problems with DVD player.

  1. When you say "drive of DVD (F) is an a Toshiba" is an external drive or internal?
  2. Are what fixit you referring?

  You can try the steps from the following link and check if this solves the problem of DVD player:

  Note: section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article:

  http://Windows.Microsoft.com/en-in/Windows-Vista/back-up-the-registry

  The CD drive or the DVD drive does not work as expected on a computer that is running Windows Vista

  http://support.Microsoft.com/kb/929461

  If the problem persists, or if you need any help about Windows let us know.

  We will be happy to help you.

• No audio, cd/dvd devices does not work, can not update via Microsoft Update, usb memory sticks not recognized and much more

  The initial problem was no audio sound on CD.  The computer had other system sounds.  I uninstalled the Realtek drivers and downloaded from the website computer and reinstalled.  Still the same problem. I tried to adjust the volume control and clicked the speaker at the bottom on the right bar.  I got a message saying there is no mixer device and the small speaker disappeared and reappeared even after several reboots.  There is also an error "no audio device".

  After reboot, the computer gives this error message: "Generic Host process for Win32 Services has encountered a problem and needs to close." We are sorry for the inconvenience. »

  While trying to find a solution on the web, I discovered that the computer does not recognize the usb key,
  It won't restore to an earlier time,
  the CD/DVD drive will not run the data disks

  and Windows Update will not update.  The error message said: "the site has encountered a problem and cannot display the page you are trying to show."  There is an error number: 0x800706BE I tried to find this error message on the MS knowledge base, but it is not listed.

  The last Windows Update was on April 16, 2009 so I tried to restore to April 15, but it says 'system restore is not able to protect your computer.  Restart your computer and restart System Restore. "    After the reboot, the same thing happens.

  Any help is appreciated.

  The data is not "hostage." Pull the disk and put it in a box disc or it slave to a working computer and retrieve the data. If you don't have an additional computer you will need to borrow a friend or with the machine at a tech. You can also try the o with a Linux Live CD boot. I like Knoppix, but there are others. This has two advantages: 1) if the system works, you can back up all the data that missed your last backup; and (2) with the machine running Linux allows to determine whether the problems are caused by software or hardware. If the machine is unbearably slow and/or Linux cannot run correctly, you know that the hardware is at fault. If the machine behaves perfectly under Linux, you know that the software (Windows) is at fault.

  Whatever you do, do not install Windows without test material. If the hardware is at fault, software solutions like reinstalling Windows will be unnecessary. MS - MVP - Elephant Boy computers - don't panic!