Drive or power supply problem? System beep and nothing else

Similar Questions

• Pavilion a6655f: hard drive or power supply problem?

  A few days ago, I was trying to low loading part of the steam.  My download speed is 30 kbs, obviously not good.

  I did some basic checks, malware, viruses, etc., but did not find any problem.  I did a diagnostic check and got a BIOHD-8 error code, which indicates a hard drive problem.  I decided to try to reset the computer back to the factory setting before changing the hard drive and once that I made and updated windows Vista for several hours, I restarted the diagnosis and he came clean.  Then I updated my software, including steam and a few games.  Downloads were fast and had no problems.  Later that night the computer started to shut down randomly, and I was unable to run any games.  Thinking it's maybe a power supply problem, I have replaced my graphics card with an elder who needs less energy.  I am able to run without any problems so far.  So, I'm looking for help in identifying my problem.  HDD problem, power supply, something else?  Any thoughts are appreciated.

  Pavilion a6655f

  Windows Vista

  PS 500 watts

  WD hard drive provided with the computer

  Thank you.

  Ken

  Hard to say without proper trials.

  You can use a hardware monitor HW Monitor to monitor tensions it is: http://www.cpuid.com/softwares/hwmonitor.html
  But there is no software that can test a power supply.

  You can get a tester of hardware like this too: http://www.newegg.com/Product/Produc...82E16899887005

  But there is really no of it will predict fails if the power supply, if you overloaded it, if its duration in time high, or if the power supply is a device of poor quality that can be subject to failure.

  You can also check that your power cable is comfortably installed on the computer and not frayed.  Try a different wall jack where there are fluctuations in power.

• 3525 Deskjet printer power supply problem

  Brand new printer, I have been connected, printed OK. Once off, lights not again unless you pull on the power cord plug, then plug it in yet. Then can be turned on. But once off so the same problem all over again. I tried different plugs/Sockets, same problem with them all. Same thing happens when the printer is connected to the electric network without being connected to a laptop Desk/computer. Is this a power supply problem? Is it not ridiculous to do out of the box?

  Thanks for any help,

  Nicholas

  Hi Nicolas,.

  The latest firmware should solve the problem you are experiencing.

  Download and install the update of the firmware for your operating system below:

  32 bits:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128070-2&cc=us&DLC=en&LC=en&OS=4157&product=5241265&sw_lang=

  64 bit:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128071-2&cc=us&DLC=en&LC=en&OS=4158&product=5241265&sw_lang=

  If the printer connected to your PC via the wireless network and the update fails to install, connect the printer with a USB port in order to complete this update, or update your device from its screen as follows:

  http://support.HP.com/us-en/document/c03250770

  Kind regards

  Shlomi

• Strange on my Satellite A100 power supply problem

  Hi I hope it's just me in Sun.

  I plugged my power on my laptop today and found that no power is getting to the laptop. I checked all the obvious things like the fuse and have even tested the output of the power supply with a multimeter and I get what looks like the correct voltage.

  However, when the power supply is plugged into my laptop blue "alternating current" does not and windows wants to say I'm running out of battery.

  Someone else had this problem? It is a work of repair and return? (I hope really not).

  Thank you

  Doug

  > Is this a work of repair and return
  I'm afraid, m Yes :(

  But the question is; malfunction of what part?  :|
  Maybe that your inquiry is good and everything is ok with the AC adapter / CC.
  This means that there could be something wrong with the laptop itself.

  Maybe it's only one loses the connection between the plug and the motherboard or most serious problem as a malfunction electronics power?  :|

  Who knows. It of very difficult to say what's wrong without any diagnostic tests
  I recommend you contact a technician in your country. He could check the laptop and found much faster fault as a user simply ordinary like you and me.

  Good luck

• Power Supply problem when installing Windows 7

  So I'll keep this short and to the point. I was upgraded yesterday from Vista to 7. Has made all the necessary updates and restart before installing 7. While it was installing, I weppe out of the room, came back and my monitor was empty... Silly me, I thought it was a reboot during installation. Futher glance, the monitor is in standby mode and the PC itself has been disabled. I waited about 10 minutes and it was always off. So I hit the power button, and it will not turn back. Tried the flipping of switches, different cables. Even called tech support, to get your warranty has expired and its $ 99 for me you tell the problem... Then he became the Lady on the line, telling me something I already knew... I got a power supply problem and I had to mapy 340.00 to repair... My question is this... It was just the stars lining up properly and my diet is to bite the dust while I have been upgraded or is there more behind it?

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads

  "Download Windows 7 installed and activated on your PC."

  They will help you in the Windows 7 Forum at the above address.

  See you soon. Mick Murphy - Microsoft partner

• 1V - 5v linear output using power supply 5v, voltage divider, and variable resistance

  How can I get 1v - 5v output linear using power supply 5v, voltage divider, and variable resistance?

  Have the you wired as an attachment?  Using my schema, you can calculate the current flowing through the pot based on the fall of the tension in the pot

  4V / 10Kohm = 0.0004

  Kirchhoff's current law, we know that the same current flows through the circuit so now we can calculate the leg below the wall, based on the current and the fall of desired voltage across the resistance

  1V / 0.0004 A = 2.5 K Ohm

  My scheme maintains the current flowing through the circuit of constant, so the voltage divider must never change.  Assuming a linear pot, you will get a swing of such linear voltage as measured at the wiper.  If you wired the pot, a different way, then more then likely, you change the total resistance of 5V ground that would have the common effect that would effect the tensions.

• After removing system Antivirus care of my PC, I got an error message in function recycle something w / drive c. I clicked on OK and nothing of what is removed now appears in the Recycle Bin.

  After all functionss suggested or recommended to rid the SCA, I got an error messge something on recycling function was not in the c drive and I clicked OK. Now, when the Recycle Bin is opened after deleting without elements appear. Is there a correction/fix for this?

  Moved from feedback

  Original title: after having rid SCA from my PC I hade an error message in the function recycle something w / drive c. I clicked on OK and nothing of what is removed now appears in the Recycle Bin. This can be corrected?

  I'll have to check your other thread, but,.

  1. a single antivirus can be installed and running in real-time

  2. you can run malware and spyware like on DEMAND scanners only

  3. If you install MSE, all previous installed antivirus must be completely removed before installing mse

  4. Please read this checklist:

  http://experts.Windows.com/w/experts_wiki/89.aspx

  MSE installation checklist

• trying to turn on my HP compaq d330 but red light flashes and a beep and nothing does not illuminate

  trying to turn on my HP compaq d330 but red light flashes and a beep and nothing comes up on help a beginner please

  You can try to remove and replace the memory and see if it works.

  If this does not work, delete all except one module of memory (if the PC has more than one) and see if the PC works normally with the chip memory. If it beeps, remove and replace it with the memory you removed and keep doing that until you find the defective memory chip.

• Boots Vista black screen with white cursor and nothing else (Black Screen of Death)

  After a download from Microsoft update last week, my system has rebooted. He first had a screen blue error, rebooted, reported a disk error and automatically run CHKDSK. Since then, the system has started a black with white slider screen and nothing else. This happens at startup options (Normal, safe, safe with the last command good known configuration). Not even sticky keys would come to the top. CTRL-Alt-Delete, Ctrl-Alt-Esc and all other keys has nothing did. Even with a right click.

  I searched all over the web for solutions. I found (and tried) several over the past week, but nothing has worked.

  Here's what I tried...

  F8 held key on boot to the top and entered the startup recovery. Ran of recovery. Initially so found of disk errors. Those fixed. Then he said he could not repair the system and reported two pilot errors.

  Tried system restore. He said that I had no restore points (even if I know that I had before).

  With the help of recovery options, I went to the command prompt. Asked to RegEdit and load the Software hive. Checked the connection entry Windows NT; made sure, it has been set to explorer.exe

  The system, checked RpcSs Key hive. Already the NT AUTHORITY\NetworkService value

  Renamed event connects winevt and not create the Logs folder

  Removed the hard drive. Attached to another system (as slaves), and the registered file permissions. They have screwed everything up. The fixed file permissions and drive put back in original system.

  Œuvres self-retaining keys now. Do not, however, as my sticky keys doesn't have a link to configuration.

  Went back into recovery startup via the F8 key at startup. Now, when I run start recovery, it says that everything is going well and there is no problem.

  I have download the hotfix from article 977675 Microsoft, but I don't know how I can apply it without being able to get into windows. I would like to contact MS e-mail or chat support, but I can't get the product ID without being able to connect (frustrating talk).

  I would like to reinstall OS, but HP does not provide an installation disc with their systems (only a full restore partition). My system is backed up (with the exception of the Windows folder), but I really don't want to have to make a full recovery, as I have a lot of specialized programs and settings that would probably take me a week to re - install and re - set.

  Anyone have any new ideas?

  Hello

  Here's my usual BlackScreen convenience store, because it may be that you haven't tried
  or if you have access you might be able to come back and start some of them.

  ----------------------------------------------------------------------------------------------------------

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have your system disks
  manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore there only to)
  being bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - type no parenthesis)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• my mouse wheel controls only my volume and nothing else

  My mouse has suddenly begun to control my volume and nothing else, it won't scroll on any page, does not work in photoshop and will not work on one of my games, I haven't downloaded a mouse wheel for volume control programs and I have uninstalled and reinstalled the drives for my mouse Reset my computer several times, checked in the control panel mouse settings and can't find anything that may be the cause of the problem, any suggestions?

  I came here with the same problem and tried all of the above. I came close to reformat my hard drive, but the answer turned out to be very simple.

  I replaced the batteries in my wireless mouse and it works fine now. :)

• White PSE 6 welcome screen and nothing else

  Started all of a sudden, no problem previously. Installed on an iMac running 10.5.8. Blank home screen and nothing else. Tried to reinstall... nothing works... help!

  What happens if you turn off your internet and then start PES 6?

  There has been a rash of posts in the forum on photoshop cs3 photoshop, do something similar, I wonder if it is related

  PES 6 is based on the cs3 code.

  If it's the same thing, then maybe it's screen recording your seeing (or do not see because it is empty)

  If you start PES 6 without internet on and the registration screen that you see, press never register and if I hope to solve the problem.

• I'm looking for something, or even click on a link "for you", that he - and nothing else than the spinning wheel.

  I'm looking for something, or even click on a link "for you", that he - and nothing else than the spinning wheel.

  It is easier to go to YouTube, which I prefer not to do.

  < published by host >

  It's real comments to your message:

  You talk to other users here, not to Apple directly.

  Click below and select the product (s) on which you have any concerns or suggestions:

  http://www.Apple.com/feedback/

  Then select your product

  When you contact Apple to give them feedback, note the statement at the top of this page:

  'Use the form below to send us your comments. We read all comments

  carefully, but please note that we cannot respond to comments you

  submit. »

• DWCS # previews only PHP include and nothing else

  Migration of DWCS2 towards my whole site DWCS3 PHP display mode "Code and Design" correctly. They seem to work fine if I make changes in the Code and download. It is very difficult for me to work that way, though.
  
  When you work in CS2 design mode would not display includes the "PHP" as I expected. Everything works beautifully on download on our server. Now, however after upgrade to CS3, Dreamweaver seems to want to only display the first statement 'PHP include' and nothing else that I did on the page.
  
  I created a few screenshots to the following address. Comapison between CS2 and CS3 Code and Design views
  
  Any help would be greatly appreciated. Im sure I must have done something incorect when I built the site initially, but I don't know what. The online site can be accessed at Heart Center of Wyoming
  
  Please let me know if any other information is required.
  
  Best regards and thank you.

  Thank you, David.

  I knew it was something basic.

  Best regards.

• HPZ620Workstation and Evga Titan SCBlack POWER SUPPLY PROBLEM Edition

  Hello world

  I bought (Evga Titan SC Black Edition), but I have a problem with my power supply hpz620

  http://www.plugloadsolutions.com/psu_reports/HP_S10-800P1A_ECOS%202609_800W_Report.PDF

  I have two xeon processors (2 * 135W) and my question is the graphics card has enough power to do with the rest?

  Second problem is the molex cable I have only one. What is the best solution for me?

  Edition of black titan sc EVGA specification

  Performance

  NVIDIA GTX TITAN BLACK

  Hearts CUDA 2880

  967 MHz Base clock

  Boost 1072 MHz clock

  Memory

  6144 MB, 384-bit GDDR5

  7000 MHz (in force)

  336 Gbps of bandwidth

  Hello:

  You can also ask your question on the HP Business Support Forum - z section of workstations.

  http://h30499.www3.HP.com/T5/workstations-z-series-XW-series/BD-p/BSC-272#.U4CnZ-lOW9I

• Studio XPS 435 t / 9000 power supply problem

  My diet giving me in my Studio XPS 435 t/9000. The fan is very noisy, but otherwise there is no obvious symptoms. Since the system is about 5 years, I was planning to change some parts.

  My questions are:

  (1) what could be the cause of the fan to be strong, and what are the potential problems with that?

  (2) a system of 435MT 475W PSU would be compatible, or would I need specifically a 435 t?

  The first thing I would do is keep the Office of your garage. Open the side cover. Use compressed air can and blow all the dust that has accumulated in the tower. Blowing from the rear of the PSU and the inside of it. Replace the cover and retest for the noise of the PSU. The power supply 360w on Studio XPS 435MT will not work. The only Dell validated PSU for the Studio XPS 435 t / 9000 has been F217J 475w. The best video cards, we validated our eating 475w were:
  2XTG4 AMD Radeon HD5870
  5X2CH Nvidia GeForce GTX260

  You might consider installing a power supply of higher power, but with a single card video, you need something bigger then a 650w. You could then spend the video card for sale retail Nvidia GTX660.