Strange on my Satellite A100 power supply problem

Similar Questions

• On Satellite P100 power supply problem

  Hai
  I bought the new laptop Satellite P100. Suddenly it does not start (no power to notebook) and the same time, I have only checked by the only power a/c no result, also do not charge the battery. I put t know what is the reason. Can someone give suggestion?
  Thank you bye.

  If the power light is blinking there is probably a problem with the electronic power supply. In this case, the laptop sends flashes code. Read this code, technicians can identify the problem.
  Please, don't waste your time but the closest service provider contact allowed in your country.
  After 18 months of that guarantee must be valid (it depends of course on where you live) as well as the repair must be free.

• Pavilion a6655f: hard drive or power supply problem?

  A few days ago, I was trying to low loading part of the steam.  My download speed is 30 kbs, obviously not good.

  I did some basic checks, malware, viruses, etc., but did not find any problem.  I did a diagnostic check and got a BIOHD-8 error code, which indicates a hard drive problem.  I decided to try to reset the computer back to the factory setting before changing the hard drive and once that I made and updated windows Vista for several hours, I restarted the diagnosis and he came clean.  Then I updated my software, including steam and a few games.  Downloads were fast and had no problems.  Later that night the computer started to shut down randomly, and I was unable to run any games.  Thinking it's maybe a power supply problem, I have replaced my graphics card with an elder who needs less energy.  I am able to run without any problems so far.  So, I'm looking for help in identifying my problem.  HDD problem, power supply, something else?  Any thoughts are appreciated.

  Pavilion a6655f

  Windows Vista

  PS 500 watts

  WD hard drive provided with the computer

  Thank you.

  Ken

  Hard to say without proper trials.

  You can use a hardware monitor HW Monitor to monitor tensions it is: http://www.cpuid.com/softwares/hwmonitor.html
  But there is no software that can test a power supply.

  You can get a tester of hardware like this too: http://www.newegg.com/Product/Produc...82E16899887005

  But there is really no of it will predict fails if the power supply, if you overloaded it, if its duration in time high, or if the power supply is a device of poor quality that can be subject to failure.

  You can also check that your power cable is comfortably installed on the computer and not frayed.  Try a different wall jack where there are fluctuations in power.

• Power Supply problem when installing Windows 7

  So I'll keep this short and to the point. I was upgraded yesterday from Vista to 7. Has made all the necessary updates and restart before installing 7. While it was installing, I weppe out of the room, came back and my monitor was empty... Silly me, I thought it was a reboot during installation. Futher glance, the monitor is in standby mode and the PC itself has been disabled. I waited about 10 minutes and it was always off. So I hit the power button, and it will not turn back. Tried the flipping of switches, different cables. Even called tech support, to get your warranty has expired and its $ 99 for me you tell the problem... Then he became the Lady on the line, telling me something I already knew... I got a power supply problem and I had to mapy 340.00 to repair... My question is this... It was just the stars lining up properly and my diet is to bite the dust while I have been upgraded or is there more behind it?

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads

  "Download Windows 7 installed and activated on your PC."

  They will help you in the Windows 7 Forum at the above address.

  See you soon. Mick Murphy - Microsoft partner

• 3525 Deskjet printer power supply problem

  Brand new printer, I have been connected, printed OK. Once off, lights not again unless you pull on the power cord plug, then plug it in yet. Then can be turned on. But once off so the same problem all over again. I tried different plugs/Sockets, same problem with them all. Same thing happens when the printer is connected to the electric network without being connected to a laptop Desk/computer. Is this a power supply problem? Is it not ridiculous to do out of the box?

  Thanks for any help,

  Nicholas

  Hi Nicolas,.

  The latest firmware should solve the problem you are experiencing.

  Download and install the update of the firmware for your operating system below:

  32 bits:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128070-2&cc=us&DLC=en&LC=en&OS=4157&product=5241265&sw_lang=

  64 bit:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-128071-2&cc=us&DLC=en&LC=en&OS=4158&product=5241265&sw_lang=

  If the printer connected to your PC via the wireless network and the update fails to install, connect the printer with a USB port in order to complete this update, or update your device from its screen as follows:

  http://support.HP.com/us-en/document/c03250770

  Kind regards

  Shlomi

• Satellite A30 - power AC problem

  Hello.

  My computer has a strange random problem related to AC power. It stops randomly. Here is the description (sorry my bad English):

  * Power supply only: (battery not installed) it stops randomly.*

  This isn't a problem of overheating because I have everything clean every 2 weeks. Average temperature of CPU is 45note? Aºcelsius.
  What happends problem with my 2 original adaptors.
  In the CC is fine. No pins bgas and pass the AC adapter cable is not stop it.
  Cables AC adapters are in perfect condition.
  It just keeps shut down. Sometimes I turn the computer and after 30seg its stops around the... other down time 5 minutes... other times 5: 00...
  It happends no matter the cpu load... 0% or 100%...
  I'm not even touch the computer!

  * AC POWER AND BATTERY: * start the computer the battery.
  Suddenly the recharge battery led turns off and he starts to perform.
  Poster source ca but Toshiba power management software it "AC online - DISCHARGE BATTERY"
  Its the same as if I remove the ac power cable but the ac adapter is always recognized.
  Once I turn off the computer, battery starts to charge again. Battery led as active.

  IM thinking on protected by some kind of regulator of tension or something related.

  Any ideas? I already open and look for damaged components but everything seems in good condition.

  Anyone with a similar problem which was resolved by the support from toshiba? What was the problem?

  Best regards

  Hello

  I think that no one here will be able to tell what's exactly wrong with your laptop.
  All makes really strange sounds and I think that it s related to the power supply electronic malfunction, which is part of the motherboard.
  That's my personal opinion and in this case, the motherboard needs to be replaced

  Of course, you can contact the ASP technician to check the laptop. The guy couldn't say exactly what part is malfunctioning and if the motherboard is affected
  As you know the new motherboard is expensive about 300Euros
  So you should really consider if a laptop second hand would be a better choice

• Satellite 1410 - power on problem

  Hallo,
  I have some problems with my Satellite 1410 303.
  After the stop, without disconnecting the power supply, if I try to put the laptop by pressing the button start the laptop does not start and the orange green power led indicator lights up, indicating a power problem.
  This problem appears after updating bios and Windos XP Service Pack 2.
  Can someone help me, please?
  Thanks
  Andrea

  Hi Andrea

  The first thing you can try is to remove the battery for a short period and try to start Notepad without power supply.
  It will also be interesting to know if the laptop turns on without battery with power running. There is the problem after that, is it possible that power supply microcontroller don t work properly.

  If the orange flashing is not constant it may flash code.

• Satellite A50 power on problem

  I have a satellite A50 produced in 2004. I was getting messages flashing up on top of the problems of critical battery despite being connected. Finally the computer lost all power. Now it is quite dead, and I can't make it work on the power supply. I removed the battery and plugged, but still have no power. There is no light on any name that is not in hibernation. It seems that some internal fuse needs to be replaced, or something that prevented completely from the power of work. I have changed the fuse in the plug and tried the power outlets alternative. Any ideas?

  Hello

  Maybe there is a problem with the electronic power supply.
  In this case, the motherboard should be replaced.
  But you should ask Toshiba service to find the fault.

• With Tecra750DVD power supply problem

  My laptop recently decided to refuse to turn on when I turned on. There is a yellow light in the position of "power" over the front of the machine, but it won't start. I tried all the options: Power Supply Unit only, only battery, Power Supply Unit + battery and nothing works. Fuse is good in the plug of power supply. Battery is less than 12 months.

  Hello

  You can remove the battery completely when problemshooting this kind of predicament.

  First of all - what impression the power button? Does it feel as it should? Refers to how it used to feel? If this is not the case, check if there is an active "lock" behind it.

  Some models have a safety lock to keep the machine from accidentally start in a bag or two.
  Please look at the LED that indicates that your adapter is connected. When you try to switch the machine on, what is happening with this LED? Always the same fixed green light or suddenly out or flashing?
  If out, please try to get your hands on another adapter (borrow prefferably). If it flashes then try to remove the AC adapter, remove any option that can be easily removed, CD/DVD, memory, expansion card PC and so on.
  Try to restart it (remember to join HQ again). Even? If Yes, then sorry to say I think that your machine needs service. If this isn't the case, then there could be hope.

  Disconnect the AC and put back in place the units that you have deleted before, one by one and after each unit, try to restart the machine.
  If it starts fine, remove the unit and reconnect the next unit. Perhaps you will find that there is a problem with an external device (memory, CD, PC Card and so on), then at least you can continue working more or less as before the problem.

  Good luck

  Tom

• Satellite L775 - power supply for cars

  I would use (and connect) my laptop Satellite L775 - 12L in my car.

  Do you know of any food that I could use with voltage of 12V and specific records in cars?

  Like this outputs a specific AC adapter (19V, 3, 95 has), I was wondering if anyone of you has experience with car power supply that would work with this laptop (I used a standard without success).

  Thank you very much!

  Hello

  I googled for Satellite L775 card adapter and found a few deals online.
  It is important that the card adapter would provide an output 19V

  Of course, you can contact the Toshiba service provider in your country and can order a genuine part of Toshiba from guys.

• HPZ620Workstation and Evga Titan SCBlack POWER SUPPLY PROBLEM Edition

  Hello world

  I bought (Evga Titan SC Black Edition), but I have a problem with my power supply hpz620

  http://www.plugloadsolutions.com/psu_reports/HP_S10-800P1A_ECOS%202609_800W_Report.PDF

  I have two xeon processors (2 * 135W) and my question is the graphics card has enough power to do with the rest?

  Second problem is the molex cable I have only one. What is the best solution for me?

  Edition of black titan sc EVGA specification

  Performance

  NVIDIA GTX TITAN BLACK

  Hearts CUDA 2880

  967 MHz Base clock

  Boost 1072 MHz clock

  Memory

  6144 MB, 384-bit GDDR5

  7000 MHz (in force)

  336 Gbps of bandwidth

  Hello:

  You can also ask your question on the HP Business Support Forum - z section of workstations.

  http://h30499.www3.HP.com/T5/workstations-z-series-XW-series/BD-p/BSC-272#.U4CnZ-lOW9I

• Satellite A100-201 touchpad problems

  I searched through the forums and many people have had problems with the touchpad, but nobody seems to have quite the same problem, as I have! If this has been asked to answer also my apologies, but I can't!

  I have a Satellite A100-201 with a 'Tablet' (as described by the technique of the Toshiba product - no mention if it comes to Synaptics or Alps, or anything else, is not that it would mean anything for me anyway. It is certainly NOT a dual pad that turns on with the blue buttons, etc.)

  Have had the laptop for over a year, and I got it all the time I have a problem where 'sometimes' function on the touchpad scroll bar doesn't work, all on his own. Sometimes I turn on the computer and it works fine, sometimes not. The same goes for the service where you tap the top right of the button and the narrowings of the active window (don't know what this is called). There seems to be no reason for this, I find the scrolling feature really useful. The rest of the touchpad functions works very well.

  I don't know if it's to do with drivers as I am not computer-oriented (I can use one for day to day stuff, but that's all) or upgrades of windows as no one else mentioned on another thread.

  If anyone has any idea how I can:

  (a) turn back ON the scrolling feature and

  (b) set it so it is permanently under voltage I would be really grateful!

  Thanks in advance!

  Hello

  do you have challenged yourself with synaptics/Alps touchpad Control Center / (whateveryourtouchpadsmanufactureris) and checked the settings?

  As far as I know are these touchpads really complicated when you use them, but * more * usable after setting the key to touch about the sensitivity options, etc...
  You can configure almost the entire touchpad area to adapt to your needs...

  Please, check the settings and make sure that your keyboard is configured correctly.

  Welcome them

• HP Envy Pheonix 810-210: Possible POWER supply problem?

  I bought the HP Envy 810-210 a Phoenix earlier this year and recently replaced a 645 GTX graphic card a GTX 960. When I replaced it I noticed the power cord was appropriate is more good in the power supply and can fluctuate a little. Now when I move my PC, the power cord will be disconnected and will Crackle. This turns off my computer and I have to tinker with a correct position in the socket to restart.

  What would be the recommended action for this? Is this a problem of cord or plug, do you? Y at - it a power supply that matches or is better than that which is currently in my computer (here), which will be a fit if it needs to be replaced?

  Hello

  The CX600 Corsair or CS650m would be an excellent choice for a power supply.

• Graphics - Satellite A100-313 card problem stops itself

  I have a satellite A100-313 and I use vista.
  Every time when I'm playing games, the laptop turns off after a while. It varies, normally have 10-20 minutes of play.
  And when I immediately turn on again, I get a black screen, but the computer is running. I have to wait a bit to get back to the screen to work.
  So, he goes to the top and goes to 1024 x 764 resolution (the native resolution is 1280).

  I guess it's a problem of graphics card (I have a Geforce Go 7600). I have already updated to the latest vista drivers available on the Toshiba site (the September).

  What can I do to fix this? Automatic shutdown normally only happens when I play games.
  Any help is appreciated.

  HM, delicate sounds.
  I suggest the following:

  Download the latest bios for your machine on the toshiba download site:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  And finally and most importantly, check if your cooling system of your machine is not clobbed with dust. You can clean it with a can with compressed air to remove dust from the fan and the heatpipe fin.

  If you have any questions, just ask.

  Have a nice weekend

• Strange question on Satellite A100 LCD

  Hello

  I just bought a laptop A-100-599 and I started noticing that after 10 to 15 minutes of the lower part of the screen LCD (one that is close to where it connects with the rest of the computer) starts to overheat to the point where I can see the black plastic of different color close to overheating. The image does not change there are no problems in this area, the laptop freezes not or anything like that.

  Is this normal or should I worry? :)

  I have Satellite A100-504 in front of me and look at the screen. Everything is ok. Your problem of reading I really do not understand exactly what is happening and what it looks like. It will be very useful to see the picture of it.

  Anyway, Satellite A100 is fairly new laptop model and, in my opinion, you should contact the service and show them what is happening here. According to your description, I can't tell if this is normal or not, but it sounds pretty suspect.