DVD - rom sd - r 2212 working properly

Similar Questions

• Qosmio G30 - DVD-ROM drive has stopped working

  I have a Qosmio G30 age of 3 years and the DVD - ROM drive has stopped working.

  He still pulls in, but it will not read or burn discs.

  I received a quote of £360 Toshiba to adapt to a new one that seems generous.

  Anyone know where I could get it fixed cheaper than you?
  Or better yet... anyone know where I can I get it fixed?

  David Hutchinson

  Hello
  This is not an answer to your question but can solve the problem if it is the same that I had.
  In my case, the drive tries to spin but it slips. Only the motor shaft rotates and the drive remains at low revolutions that were not even stationary.
  The problem was caused by the fact that the plastic part (black color) of the mechanism which engages the disc (CD or DVD) slips on the
  motor drive, axle and th couldn't do a full rotation or runs at the specified speed.
  The solution is to delete the article in plastic and put a small amount of super glue on the axle and then put it back.

  Where there is a similar issue, I hope that solve you it like I did.

• DVD - rom not open or work

  I have a dvd-writer/cd-writer combo that operates. Below, I have a dvd - rom that is not open or read. That's happened? Can it be fixed?

  The following links may be a place to start:

  (982116) your CD or DVD drive is missing
  or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116
  (Windows XP / Windows Vista / Windows 7)

  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Beyond that...

  If you are uncomfortable, maintaining your own system...
  You can open the suitcase and try to put in place caps
  for the reader, but it sounds like the hardware failure.

  Reach... Device Manager and see if the drive is marked.

  The following article might be worth a visit:

  The symbols, Error Codes Windows Device Manager
  and definitions in Windows 95, 98, Me and XP
  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00035740&cc=us&LC=en&DLC=en&product=3758068

  I suspect that the solution is to replace the drive.

  Good luck.

• CD-ROM/DVD-Rom drive has stopped working

  original title: READER of CD/DVD FAILURE

  My CD/DVD drive has suddenly stopped working.   I cannot now copy/burn discs or I can't play pre-recorded discs.   Can someone tell me what could have happened please?

  Hi Alan_6C,

  ·         Remember to make changes?

  You can check if this article helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

• error code 41 ___error code 41 cd/dvd rom driver does'nt work I have an atapi 20a4p

  CD dvd rom gone I need help getting the error code 41

  Hello Randyace2425,

  Thank you for your message.  Click HERE and run the FixIt!  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• I have windows 7 (64-bit) and my DVD - Rom drive does not work. For some reason, that I disabled it, how can I activate it? Thank you, Billy

  This issue should really be down here. There is nothing to add.

  Thank you
  Billy

  Hi Billy,

  Thanks for choosing Windows and thank you for providing an opportunity to help you.

  According to the description provided, you have problems with activation DVD ROM.

  Have you tried the steps suggested by Sandeep V from the link below?

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/i-am-running-Windows-764-bit-and-my-DVD-ROM-has/0e7c6ec1-e61c-40af-8d88-af816681e1ba

  Answer to us if you have problems with activation DVD ROM or any other problem of Windows, and we would be happy to help you.

  Good day!

  Hope this information helps.

• Satellite L300-1CU-DVD-rom drive does not work in Win7

  Hello

  I have IMPROVED MY TOSHIBA Satellite L300-1CU FOR WIN 7 NOW cd rom (MAST * one UJ880AS DVD RAM) quit working. DRIVE USED DOOR OPEN WHEN I CLICK ON THE DRIVE IN EXPLORER (DVD RW drive (D :)) MESSAGE SAYS "PLEASE INSERT a DISK INTO DRIVE D:" what I'VE DONE.))

  I DELETE THE UPPER & LOWER EDITORS IN THE REGISTRY AND UNINSTALLED THE DRIVER DVD AND STARTED RE! NOTHING HAS WORKED, PLEASE COULD YOU HELP?

  SO THAT THE UPGRADE OF THE SYSTEM OF THE UNITED NATIONS INSTALLED TO VARIOUS PROGRAMS OF TOSHIBA... !

  Did you upgrade using the Toshiba upgrade kit or you installed Win7 clean and clean installation?
  Can you confirm that the optical disc drive works well with factory settings (Vista preinstalled original)?

• External Combo CD-RW/DVD-ROM drive does not work with USB 1.1

  Hello world

  I have a problem with the PA3352E - 2 CD 2 CD-RW/DVD COMBO USB 2.0. A colleague is owner of this car and use it on a NB DellC610 with Windows XP on it. The problem is that the drive does not work with this type of nb (with a NB from Fujitsu-Siemens newest there no problems); There is always an error message about "surge." I think it has to do with the USB 1.1 because the player seems to be built for USB2.0. Is it possible to use this drive correctly with usb1.1 (ok, the flow is low, but more important is it works in general)? Unfortunately his nb will not work with USB 2.0...

  Thank you very much in advance.

  Kind regards
  Steffen Rieger

  Hello

  AFAIK this external must have a power adapter. You use it too? I'm not 100% sure, but there are difference how much power Gets the USB slot. Toshiba notebooks is around 500 my and some producers another laptops send between 300 and 500 my. The external device requires approximately 700 my.

• Drive DVD M30X 165 are not working properly

  Hello
  I bought this phone 2 weeks ago, but now the drive hurts... sometimes it do not read the CD, after some testing, it works but its's not me on my nervs...

  Now, I wanted to burn a cd, but this does not also, ahead nero and burning of windwos xp program simply cancel before writing on cd...

  Hello Freddy

  Your device is a new and should not worry about this. Everything is possible of new units. Please check if there is a problem with the help of original music, CD or DVD that you can find in every store. If you still have the problem with the help of this original media it may be hardware malfunction.

  In this case, please contact your local dealer or service partner, and if the unit is defective it will be changed. The warranty will cover this cost.

  Either way, I use Nero software of engraving with three different machines and have no problem at all.

• CD-ROM/DVD-ROM drive does not work. Device Manager indicates problem and there is no volume listed on the Volumes, how to fix tab?

  Description of the drive is HL-DT-STDVD +-RW GSA - T11N ATA Device Properties. Verified drivers and they are up to date.  Under device status "this device cannot start. (Code 10) clicked on search the Solutions, but no solutions are shown.  Have trouble with the DVD because I had the computer and have had several conversations with Dell but I think that my extended warranty just expired.

  Hello

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• DVD rom no longer works due to the program installation CD MagicDisc

  My CD/DVD-ROM ProBook s 4330 worked perfectly for a few months. After installing MagicDisc (a CD editing program), I started expereincing CD Player problems.

  I uninstalled MagicDisc for this new operation. It did not work.

  I reinstalled (after formatting of entire disk) Windows 7. It did not work.

  What can I do now?

  

  Bravasta wrote:

  My laptop is not under warranty.

  I don't see the CD/DVD rom drive in the Windows Explorer window.

  Microsoft CD/DVD automated fixit does not read the DVD.

  Ok.

  Troubleshooting is complete.

  Your options are to replace the DVD drive or use an external DVD drive.

  I have an external drive that I use for Ultrabooks and mini HP because they do not have DVD players. DVD USB readers are generally less expensive to replace the DVD drive in the laptop.

  Best regards

  ERICO

• P50-A-144 satellite: the CD-ROM/DVD-ROM drive does not

  Version of Windows 10 Home 1607 (Build 14393.187)

  Hello

  After Windows Update Version 1511 1607, the CD-ROM/DVD-ROM drive does not work.
  The D: drive does not appear in Windows Explorer,
  CD-Audios and videos / DVDs do not work.

  In the Device Manager, the following legacy status error message appear:
  "Windows cannot start this hardware device because its configuration information.
  (in the registry) is incomplete or damaged. (Code 19). »

  Could you tell me how to solve this problem?
  Thank you.

  The solution was to uninstall the program "Toshiba Recovery Media Creator' and system settings/Programm features.
  I still don't understand why, but the fact is that after uninstalling the CD-ROM/DVD-ROM start normal work.

  More information here:
  http://www.borncity.com/blog/2007/08...-verschwunden/

• Pavilion Elite HPE-170 t: problem with the new HP DH16D5S DVD ROM drive

  My office is a HP Pavilion Elite HPE-170 t.  I recently upgraded from Windows 7 to Windows 10.  I have two HP optical dirives, one is a writer, and the other is just a DVD ROM  Both have always worked perfectly with Windows 7.  After you have installed Windows 10 continuous burner work very well works correctly with autoplay.  However, the DVD - ROM, HP DH16D5S, immediately began using autoplay.  Actually the drive was not yet recognized as a drive when you view the drives in the file Explorer.  Finally, it would seem, sometimes taking also longer than 5 minutes or more before doing so and then would work very well.  I tried different types of media, including music CD, DVD video and DVD software with the same results.  I assumed that it was a problem with the drive, maybe a bad capacitor, etc., which was originally not start correctly.  So I ordered a new DH160D5S, but which seems to have been a waste of time and money, because it does exactly the same thing as the original.  I even changed the cables autour between it and the burner, but it made no difference.  The burner still works fine but not DVD ROM.  I tried to find a more recent driver for it, but had no chance.  I found on a Dell website for this drive which was an update of the firmware for Windows Vista and Windows 7, but not for Windows 10.  I advanced and downloaded, but when I tried to run, I got the message: "your system does not meet the minimum requirements for this update.  Update has been canceled. »

  I want to try a different brand of DVD ROM, but would have to buy one without knowing if it would help.

  Any help will be appreciated.

  Since I posted this message I discovered that there is a driver problem with this DVD ROM.  There's no driver available yet to make the drive compatible with Windows 10.  Since then, I returned the drive and replaced by another brand that is compatible with Windows 10.

• my cd/dvd-rom drive

  I have Windows vista and the CD/DVD-ROM drive no longer works when I open the Device Manager, I can not find CD/DVD-ROM device drivers

  See if Fixit can fix: http://support.microsoft.com/gp/hardware_device_problems

• CD/DVD-ROM does not

  My Dell Inspiron 580 internal CD/DVD-ROM drive does not work while an external CD/DVD drive works fine. Please advise me if I should replace the internal one.

  Thank you

  Victor

  New Member

  Hi Victor,

  Welcome to the community.

  I suggest you run diagnostics on the computer before replacing the CD/DVD drive.

  1 restart the computer and press the F12 key to access the one time Boot Menu

  2. Select Utility Partition Boot, and then press ENTER to start the diagnostics

  If the test passes, I suggest you refer to the Dell Article by clicking on the link below:

  http://Dell.to/Y2xZoA

  Thank you & best regards
  Mustapha S
  #iworkfordell