dynamic ip vpn configuration

Similar Questions

• Cisco ASA 5510 multiple dynamic config VPN L2L necessary

  Hello

  We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?

  Oleg Kobelev

  The config only you need in the ASA is: -.

  (1) set of crypto processing

  (2) political ISAKMP

  (3) dynamic Crypto map

  (4) default group L2L & PSK

  (5) Config RRI (reverse Route Injection)

  HTH >

• VPN configuration blocking Internet connectivity

  I own an iPhone6 (bought in November 14 and another iPad4 (bought in early 2014) - I face a problem even in both devices.)

  Whenever I'm trying to be devices connecting to the Internet (this either through Mobile or wireless data, I have to take concrete steps to start-up the VPN setting without which the device connect to the Internet. However sometimes (although not very often) the VPN configuration gets turned on by itself without manual intervention (on start-up or mobile data or WiFi on the device). So there is always some delay time in the connection to the Internet whenever I want to use the device.

  I would be grateful for suggestions from the community in order to overcome the problem.

  You have installed VPN software or you have configured in your VPN settings? If you have a VPN configuration, then check its configuration. If you do not have a VPN configuration or a VPN software installed, then the VPN switch in settings should not illuminate.

• Unlikely VPN configuration

  Hello

  one of our partners, had asked us a strange VPN configuration. I'm not a specialist of the ASA and I want to assure you that it is really impossible.

  We already have a VPN tunnel to the TOP. For example:

  Peer1: 1.1.1.1/32 (my company)

  Peer2: 2.2.2.2/32 (partner)

  EncryptionDomain1: 10.10.10.10/32 (our field of encryption)

  EncryptionDomain2: 20.20.20.20/24 (field of the partner encryption)

  Thus, the partner we asked to install a second tunnel with exactly the same configuration. (Homologous domain and encryptio).

  I don't think it is possible, for the reason of the match seemingly obvious to access list. In this way, I think that the ASA will get confused on which traffic corresponds to which access to the tunnel to the circulation list. It's quite a superposition of access list.

  Am I wrong?

  There might be an ASA feature that makes this possible?

  Best regards

  Fabiano Martins

  Hi, Fabiano,.

  As you rightly pointed out, it is not possible to create 2 tunnels for the same source and destination, between the same two peers.

  As a single card encryption can be applied to an interface, the different tunnels that put an end to this topic are configured with line numbers.

  When traffic is matched with the card encryption, for that, a descendant of the correspondence. And when two tunnels with the same crypto-list access are configured, then always match the first condition in the card encryption, and so the second tunnel will never come to the top.

  The most interesting question here would be, as to why your client wishes to set up such a facility.

  He may be trying to achieve something that can be done without the need for the two tunnels.

  -Shrikant

  P.S.: Please check the question as answered, if it has been resolved. Note the useful messages. Thank you.

• Branch 5505, 1 circuit ISP, Dual - peer VPN Configuration for Data Center & Track Options

  Hi all

  I have a data center with two lines of ISP redundancy and two ASA 5520 for redundancy VPN to my branches.  Each of my branches has 1 ASA 5505 with a base license and 1 ISP circuit. Currently all my VPN tunnels are built for data center main circuit ISP only, so if one goes down, I'm toast.  I need to fix this. Problem is, I don't know how I can control failover on 5505 with 1 single line branch.  Please see my picture for an example of how he looks at it right now.

  So the problem is that the data center LAN my branch has to go to is identical regardless of which circuit of data center is in the. And I know the ASA rules say only 1 VPN tunnel can be active at a time if flow are the same.  So in this case, I know you usually do:

  card crypto outside_map 1 set 12.x.xxx.20 50.xxx.xx.190 counterpart

  and then configure route followed to control when cut down the primary counterpart and turn back up by peers. But where I have only 1 ISP on the side of the branch, I'll only have 1 default route: route outside 0.0.0.0 0.0.0.0 3.3.3.2 1, will be used that the active end counterpart is the primary or the secondary data center. Also, since I did not have a second track, I can't configure followed on the main road with an SLA that defines the trigger conditions, because there is nothing to ensure the follow-up of the routing.

  How is - a would handle a situation like this? Are there other features that can be taken off the roads?  I really need to be able to define "num-package 5 ' in ALS so my sites are not beat all day, but once again, without something to follow, I can't really set up a meaningful SLAS.  Any help is appreciated.

  Thanks for the additional explanation. It helps to clarify your environment. EIGRP running on the Remote would be a nice option, but I'm not sure that it is supported on the SAA. I ran EIGRP to remote peers using IOS routers (using the two ACCORD with IPsec and VTI tunnels tunnels) and it was very effective. But on the SAA, I believe that we must seek an alternative.

  It seems to me that using reverse road Injection as part of your VPN site-to-site should work. With IPP the ASA inserts a static route to remote resources when the VPN tunnel is negotiated and traffic can flow. If you redistribute the static in EIGRP EIGRP then must learn the ways of any ASA a currently active tunnel. And who should provide the dynamic rollover you need.

  HTH

  Rick

• Site to Site VPN configuration does not

  Hello

  I just tried to set up a test site to site VPN. Diagram of arrangement is attached. Router R2 is supposed to act as the 'Internet' to allow connectivity between the two networks.

  My VPN on ASA1 and ASA2 configs are below:

  ASA1

  Note to outside_cryptomap_1 to access list VPN traffic to encrypt
  outside_cryptomap_1 to access extended list ip 10.10.10.0 allow 255.255.255.0 172.16.10.0 255.225.255.0

  Crypto ikev1 allow outside
  IKEv1 crypto policy 1
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400

  tunnel-group 11.11.11.2 type ipsec-l2l
  IPSec-attributes tunnel-Group 11.11.11.2
  Cisco pre-shared key IKEv1

  Crypto ipsec transform-set ikev1 AES - SHA esp-aes-256 esp-sha-hmac
  card crypto outside_map 1 match address outside_cryptomap_1
  peer set card crypto outside_map 1 11.11.11.2
  card crypto outside_map 1 set of transformation-AES-SHA
  outside_map interface card crypto outside

  ASA2

  Note to outside_cryptomap_1 to access list VPN traffic to encrypt
  permit access list extended ip 172.16.10.0 outside_cryptomap_1 255.255.255.0 10.10.10.0 255.225.255.0

  Crypto ikev1 allow outside
  IKEv1 crypto policy 1
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400

  tunnel-group 12.12.12.2 type ipsec-l2l
  IPSec-attributes tunnel-group 12.12.12.2
  Cisco pre-shared key IKEv1

  Crypto ipsec transform-set ikev1 AES - SHA esp-aes-256 esp-sha-hmac
  card crypto outside_map 1 match address outside_cryptomap_1
  peer set card crypto outside_map 1 12.12.12.2
  card crypto outside_map 1 set of transformation-AES-SHA
  outside_map interface card crypto outside

  I can ping with the ASA2 ASA1, but when I try to test the VPN trying from one PC to another, I get nothing.

  I tried a few commands show and they came out absolutely empty... as I have not configured:

  SH in detail its crypto isakmp

  There are no SAs IKEv1

  There are no SAs IKEv2

  SH crypto ipsec his

  There is no ipsec security associations

  Anyone have any ideas?

  Hi martin,

  Your configs are quite right. I tried your script, its works really well. Here's the configs & outputs.
  What I mentioned in the previous note follow this.

  --------------------

  ASA1

  ASA1 (config) # sh run
  : Saved
  :
  ASA Version 8.0 (2)
  !
  hostname ASA1
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 12.12.12.2 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  10.10.10.2 IP address 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  extended vpn 10.10.10.0 ip access list allow 255.255.255.0 172.16.10.0 255.255.255.0
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Route outside 0.0.0.0 0.0.0.0 12.12.12.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac tset
  card crypto cmap 1 match for vpn
  card crypto cmap 1 set peer 11.11.11.2
  card crypto cmap 1 transform-set tset
  cmap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  md5 hash
  Group 5
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  !
  tunnel-group 11.11.11.2 type ipsec-l2l
  IPSec-attributes tunnel-Group 11.11.11.2
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:00000000000000000000000000000000
  : end
  ASA1 (config) #.
  ---------------------

  ASA2 (config) # sh run
  : Saved
  :
  ASA Version 8.0 (2)
  !
  hostname ASA2
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 11.11.11.2 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 172.16.10.2 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  extended vpn 172.16.10.0 ip access list allow 255.255.255.0 10.10.10.0 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Route outside 0.0.0.0 0.0.0.0 11.11.11.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac tset
  card crypto cmap 1 match for vpn
  card crypto cmap 1 set peer 12.12.12.2
  card crypto cmap 1 transform-set tset
  cmap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  md5 hash
  Group 5
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  !
  !
  tunnel-group 12.12.12.2 type ipsec-l2l
  IPSec-attributes tunnel-group 12.12.12.2
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:00000000000000000000000000000000
  : end
  ASA2 (config) #.

  -------------------------
  OUTPUTS:

  *********************

  ASA1 (config) # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 11.11.11.2
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  ---------------------

  ASA1 (config) # sh crypto ipsec his
  Interface: outside
  Tag crypto map: cmap, seq num: 1, local addr: 12.12.12.2

  access vpn ip 10.10.10.0 list allow 255.255.255.0 172.16.10.0 255.255.255.0
  local ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.16.10.0/255.255.255.0/0/0)
  current_peer: 11.11.11.2

  #pkts program: 50, #pkts encrypt: 50, #pkts digest: 50
  #pkts decaps: 49, #pkts decrypt: 49, #pkts check: 49
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 50, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 12.12.12.2, remote Start crypto. : 11.11.11.2

  ------------------------
  ASA2 (config) # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 12.12.12.2
  Type: L2L role: answering machine
  Generate a new key: no State: MM_ACTIVE

  ------------------------

  ASA2 (config) # sh crypto ipsec his
  Interface: outside
  Tag crypto map: cmap, seq num: 1, local addr: 11.11.11.2

  access vpn ip 172.16.10.0 list allow 255.255.255.0 10.10.10.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.16.10.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
  current_peer: 12.12.12.2

  #pkts program: 49, #pkts encrypt: 49, #pkts digest: 49
  #pkts decaps: 50, #pkts decrypt: 50, #pkts check: 50
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 49, #pkts comp failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 11.11.11.2, remote Start crypto. : 12.12.12.2
  -------------------------

• CISCO 837 VPN Configuration

  Configuration

  my home pc (WIN XP + 4.6.03.0021 VPN Client dynamic IP) ===> internet ===> Corporate (CISCO 837--> LAN + static IP address)

  Hello

  I'm trying to set up a vpn between my pc at home and the CISCO837 company to access the local network.

  I can connect to the CISCO but, I can't access any host on the local network.

  Can someone help me with the basic configuration...

  Homepage:

  Dynamic IP (xxxx.xxxx.xxxx.xxxx)

  Company:

  Address IP WAN (yyy1.yyy2.yyy3.yyy4)

  LAN IP range: (192.168.254.10--> 192.168.254.50)

  Thank you

  Hello..

  1 - when you connect to the Cisco... What is the IP address that you receive from your Cisco VPN adapter. Devices on the local company network need to know how to get back to this IP address.

  Can you please send the configuration of your router 837...

• Does not... dynamic ip VPN traffic

  I'm having a problem with is taffic between two routers to work. Here are my devices:

  Main location:

  Cisco 861w (static IP)

  10.0.0.0 / 255.255.255.0

  Remote Desktop:

  Cisco Small Business WRVS4400N (dynamic IP)

  192.168.2.0 / 255.255.255.0

  At the main site, I used the Cisco Professional configuration utility to create the site to site vpn using the wizard and select dynamic ip address. In remote desktop, I've entered all the information and got VPN 'Up '.

  Now the problem is that I can't communicate with networks, except when the primary location starts a connection to the remote desktop.

  For example:

  192.168.2.100 to 10.0.0.251 ping is 100% packet loss

  10.0.0.251 to 192.168.2.100 ping is 100% packet loss

  BUT

  If I leave a constant ping from 10.0.0.251 to 192.168.2.100, then the machine 192.168.2.100 is able to ping 10.0.0.251 and get answers. As soon as I stop the constant ping running on the 10.0.0.251 of the machine then answers on 192.168.2.100 stop...

  Is happening here? I am at a loss...

  Dear Jacob...

  hope it will work for check you

  crypto ISAKMP policy 10
  BA 3des

  md5 hash
  preshared authentication
  Group 2
  XXX address 10.10.10.10 isakmp encryption key

  Set your key instead of XXX and correspond with your remote site. After that write the address of your counterpart
  invalid-spi-recovery crypto ISAKMP
  !
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac XXX
  !
  Crypto map YYY-address <> >
  YYY 10 ipsec-isakmp crypto map
  defined peer 10.10.10.10
  game of transformation-ZZZ
  match address 101

  interface <> >
  card crypto AAAA

  access-list 101 permit ip 192.168.1.0 0.0.0.255 11.11.11.11 (remote user) 255.255.255.255
  access-list 101 permit ip 192.168.1.0 0.0.0.255 22.22.22.22 user (Remote) 255.255.255.255

  After that, configure NAT with forced - access list

  For troubleshooting

  HS cry peer ipsec his 10.10.10.10

  HS cry session

  hope that your site to IPSec VPN tunnel works very well

• ASA5510 dynamic RV042 VPN

  So far, I have a phase full 1 and a phase almost complete 2, but one thing I can't understand. I see this in debugging.

  peer are not authenticated by xauth - drop connection.

  I understand well after that the proxy server is configured.

  Here is my config

  attributes of Group Policy DefaultRAGroup

  VPN-idle-timeout no

  L2TP ipsec VPN-tunnel-Protocol ikev1

  allow password-storage

  allow to NEM

  attributes global-tunnel-group DefaultRAGroup

  Group Policy - by default-DefaultRAGroup

  IPSec-attributes tunnel-group DefaultRAGroup

  IKEv1 pre-shared-key *.

  authentication of the user IKEv1 no

  I tried many different configurations on both sides, but they all fail with the error of peer not authenticated by xauth.

  Do not use DefaultRAGroup - I think that this means that you it automatically tries to create a VPN user rather than a dynamic L2L.

  Change the pre-shared key on the DefaultRAGroup to be something else (if it does not match what is sent to the other side).  Put all the config you have for DefaultRAGroup tunnel-groupp and strategy group on DefaultL2LGroup tunnel-group and group policy instead.

  Usually, the DefaultRAGroup is a type of 'remote access' that doesn't mean L2L.  DefaultL2LGroup should be set if all goes well.

• NAT, stop communication OSX VPN configuration problem.

  Hello

  It is my first time posting in this forum. I have trouble getting Mac computers (my test is OSX 10.8.2) to correctly connect the VPN to the company. We have a Cisco ASA5510, who manages the VPN applications.  Here are some details:

  -Windows computers, Cisco VPN Client (not Anyconnect) are able to connect to the VPN and access internal/etc file server computers, just as we want to.

  -Mac can establish a VPN connection, but cannot communicate with servers or internal machines. I can't connect to or ping the file server by using its IP address. Also, I can't ping my personal work computer.

  -BUT, from my work computer I CAN ping the ip address of the Mac he receives after connecting via VPN. Thus, internal Windows PC can ping external VPN would be Mac, but Mac cannot ping inner Windows pc.

  ASDM using I was able to run Packet Tracer. I got trace a ping of the machine address Windows 192.168.0.52 23 to address the 192.168.5.33/24 Mac VPN. This succeeded.

  The use of Packet Tracer to trace a ping the address VPN for Mac 192.168.5.33/24 to 192.168.0.52 Windows address 23 is not successful. The package goes through the following phases: 'Capture', 'Access-list', 'looking for route', 'Access-List', 'Options IP', 'Inspect', 'Inspect', 'Debug ICMP","Free of NAT", until it reaches"NAT"where I get this message:

  Menu - NAT Action - type

  Config

  NAT (inside1) 1 0.0.0.0 0.0.0.0

  match ip inside1 all inside1 all

  dynamic translation of hen 1 (192.168.1.1 [Interface PAT])

  translate_hits = 913403, untranslate_hits = 27

  The result is that the package is abandoned.

  Info: flow (acl-drop) is denied by the configured rule

  I'm not super familiar with ACL or NAT configuration, so I do not know what changes I need to do to make this work correctly. I find as strange as the windows pc using the customer Cisco have no problem to communicate internally after the connection, but do not have a Mac Mac built-in Cisco IPSEC VPN.

  Any help would be greatly appreciated.

  -Jean-Claude

  P.s. I have included a screenshot of the screen of Packet Tracer.

  Is your home wireless network was in the 192.168.1.0/24 subnet? If this is the case, try to change to a different subnet as you suggested earlier and see if it works.

• site to site vpn configuration

  I have windows server with two sites in different locations and that you want to configure a site to site vpn, how to configure

  Here is the Vista Forums.

  http://TechNet.Microsoft.com/en-us/WindowsServer/default.aspx

  Try server communities.

  See you soon.

  Mick Murphy - Microsoft partner

• LDAP AAA for VPN configuration

  Preface: I'm all new to Cisco Configuration and learn as I go.

  I'm at the stage of configuration LDAP to configure a VPN on ASA 5520, software release 8.3 (1).  Previously the programme installation and RADIUS authentication successfully tested, I tried to use similar logic to implement the LDAP authentication/authorization.  I have acquired a service account that queries the pub for the identification of the registered user information.  My main resource was the following Manual: Cisco ASA 5500 Series Configuration Guide using the CLI Software Version 8.3.  I did initially configurations by using ASDM, but could not get tests to succeed.  So I amazed the ASDM configs and went to the CLI.  Here is the configuration.

  AAA-server AAA_LDAP protocol ldap
  AAA-server host 10,20,30,40 (inside) AAA_LDAP
  Server-port 636
  LDAP-base-dn domain.ad
  LDAP-scope subtree
  LDAP-naming-attribute uid
  LDAP-login-password 8 *.
  LDAP-connection-dn cn = commonname, OU = ou01, or = ou02, dc = domain, dc = ad
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_ATTRIB

  ---

  type tunnel-group ASA_DEFAULT remote access
  attributes global-tunnel-group ASA_DEFAULT
  authorization-server-group AAA_LDAP

  ---

  LDAP attribute-map LDAP_ATTRIB
  name of the MemberOf IETF Radius-class card
  map-value MemberOf "VPN users' asa_default

  ---

  I tested all the naming-attribute ldap alternatives listed with the same results.

  When I test the authentication using this configuration, I get the following error: ERROR: authentication server does not: AAA Server has been deleted

  When I test authorization using this Setup, I get the same error (except for the word permission instead of authentication).

  I am at a total loss.  Any help would be appreciated.

  I would use ldp.exe to see if you can make sure that the sytnax of your ldap-connection-dn is just as you have in your config, it really helps just copy and paste.

  The problem I see is the following:

  [210] link as st_domadm
  [210] authentication Simple running to st_domadm to 10.20.30.30
  [210] simple authentication for st_domadm returned credenti invalid code (49) als
  [210] impossible to link the administrator returned code-(1) can't contact LDAP er

  I suppose your ldap-connection-dn is st_domadm and you try to test with the administrator account?

  Thank you

  Tarik

• Site IPSec VPN configuration

  Hi guys,.

  I'm trying to get the Site working on two 5505 VPN of Site I have in my lab.

  Attached image...

  I used the Setup Assistant, and I think that sounds good. However, this does not work when I run the following command:

  Community-Site # sh ipsec his

  There is no ipsec security associations

  I think I generate traffic, then I tried to ping and access IIS from one laptop to the other without a bit of luck.

  Ping between ASAs works very well.

  ASAs are 5505 8.2 (5)

  Config is:

  Community site

  interface Ethernet0/0
  Outside description
  switchport access vlan 2
  !
  interface Ethernet0/1
  Inside description
  !
  interface Ethernet0/2
  !

  !
  interface Vlan1
  Description Community Site
  nameif inside
  security-level 100
  address 192.168.20.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 50
  IP 10.181.10.2 255.255.255.0

  the obj_any object-group network
  inside_access_in list extended access permit icmp any one
  inside_access_in of access allowed any ip an extended list
  outside_access_in of access allowed any ip an extended list
  outside_access_in list extended access permit icmp any one
  outside_1_cryptomap to access extended list ip 192.168.20.0 allow 255.255.255.0 255.255.255.0 network-remote control
  inside_nat0_outbound to access extended list ip 192.168.20.0 allow 255.255.255.0 255.255.255.0 network-remote control

  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 10.181.10.1 1

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set pfs Group1
  peer set card crypto outside_map 1 10.181.1.1
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2

  tunnel-group 10.181.1.1 type ipsec-l2l
  IPSec-attributes tunnel-group 10.181.1.1

  Config on the other side is:

  Corporate

  description of remote control-network name 192.168.20.0 Community Network
  !
  interface Ethernet0/0
  Outside description
  switchport access vlan 2
  !
  interface Ethernet0/1
  Inside description
  !
  interface Ethernet0/2
  !

  !
  interface Vlan1
  Torbay Corp description
  nameif inside
  security-level 100
  IP 192.168.10.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 50
  IP 10.181.10.1 255.255.0.0
  !
  passive FTP mode
  outside_access_in_1 of access allowed any ip an extended list
  outside_access_in_1 list extended access permit icmp any one
  inside_access_in_1 of access allowed any ip an extended list
  inside_access_in_1 list extended access permit icmp any one
  permit outside_1_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 255.255.255.0 network-remote control
  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 255.255.255.0 network-remote control
  pager lines 24

  Access-group outside_access_in_1 in interface outside
  inside_access_in_1 access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 10.181.10.2 1

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set pfs Group1
  peer set card crypto outside_map 1 10.181.10.2
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  tunnel-group 10.181.10.2 type ipsec-l2l
  IPSec-attributes tunnel-group 10.181.10.2
  pre-shared key *.
  !

  Hi haidar_alm,

  After a quick glance to the configuration, I found an error with the vpn peer on the Community Site:

  peer set card crypto outside_map 1 10.181.1.1

  tunnel-group 10.181.1.1 type ipsec-l2l
  IPSec-attributes tunnel-group 10.181.1.1

  The public ip address of morality is 10.181.10.1.

  Correct configuration:

  peer set card crypto outside_map 1 10.181.10.1

  tunnel-group 10.181.10.1 type ipsec-l2l
  IPSec-attributes tunnel-group 10.181.10.1

  -JP-

• General VPN configuration

  Hello

  I looked at some sites today on how to set up a vpn anyconnect for a basic 5506-x license.

  So far, I have found this site

  https://networklessons.com/security/Cisco-ASA-AnyConnect-remote-access-VPN/

  Inside, they ask for contributions, and I do not give sites randomly my number of credit card debt for obvious reasons. I just want to know what they block that I can't see. If I know that he trusted I could rethink give them money but for now I don't trust them.

  If you know a guide like this next to the Cisco white paper, answer him in return.

  Hello

  Anyconnect configuration is the same regardless of the license you have so that you can follow any documentation out there to set it up. I saw some videos on youtube on how to do it. ASDM has also an Anyconnect installation wizard it will take 2 minutes to do following the wizard I don't think that you must pay on a website for an example of configuration, cisco documentation is very detailed check it will explain the process of the ASDM Wizard:

  http://www.Cisco.com/c/en/us/support/docs/security/AnyConnect-secure-mob...

  Best regards, please rate.

• RV042 VPN configuration

  I'm looking for help to the RV042 configuration for VPN access to local machines and Win 2008 Server.  History: had problems with remote printers created for customers log into old Linksys RV042 VPN Linksys software.  First Tech exposed server without security, and it had to be removed because he was attacked, but did not print problem.  2nd tech failed to get VPN to work after 1 tech.  3rd tech 4hours and I got the router is a piece of...  I am so on more than 1000 and unable to have a simple router put in place.  The current situation.  New RV042 with the V4.1.1.01 firmware, using the Cisco VPN client 5.0.07.0410, most of the 32-bit machines on network XP, a 64-bit win 7.  My customers do not have access to their data for too long and I need a quick fix.  Willing to pay, just the person to really know what they are doing.  Thanks in advance.  (I hope its ok to offer to hire someone!)

  Mike,

  I am sorry to hear that you're having these problems and even more sorry to tell you that you have problems with the client VPN Cisco 5.x because the RV042 does not support this VPN client. Cisco VPN client is an enterprise-level software utility that uses the IPsec protocols to connect. What you should use is Cisco VPN fast. Cisco VPN client authenticates in 2 phases while the RV042 and Cisco Qvpn authenticates in 1 phase. The router doesn't understand just how to manage connections from the Cisco VPN client. I've included a link to the Cisco Qvpn utility below. Hope this helps

  http://www.Cisco.com/Cisco/software/release.html?mdfid=282414010&softwareid=282465795&release=1.4.2.1&relind=available&rellifecycle=&RelType=latest

  Blake Wright

  HWC Cisco network engineer