VPN configuration blocking Internet connectivity

Similar Questions

• Cannot access internet when you configure with internet connection sharing.

  INTERNET HELP?

  I tried to use the internet connection to my wireless on my PC laptop not wireless using an Ethernet cable. I have connected my pc not wireless to my laptop wireless pc with ethernet cable, I did everything as requested on the site of "Dummies" and the PC says its connected but when I try to go on Internet Explorer, it does not work? HELP! : (PS) my PC is Windows Vista and my laptop Windows 7

  Hello

  1. While sharing was the Internet works fine before?
  2 did you change on your computers before this problem?

  I suggest you follow these methods and check.

  Method 1: You can follow the Windows Help article below and check that ICS is set up correctly.
  Set up a shared Internet connection using ICS (Internet Connection Sharing)
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-shared-Internet-connection-using-ICS-Internet-connection-sharing
  If ICS is not configured correctly, then you must post back the result by running the following command
  To do this:
  a. click the Start button.
  b. type cmd in the search box.
  (c) in the command prompt, you must type ' ipconfig/all' and check the result.

  Take a screenshot of the command prompt and post.
  To take a screenshot, you can follow this link below.
  Use capture tool to capture screenshots
  http://Windows.Microsoft.com/en-us/Windows-Vista/use-Snipping-Tool-to-capture-screen-shots

  Method 2:  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?T1=Tab03

  I hope this helps.

  Thank you.

• Cisco VPN drops my Internet connection

  I have anyconnect Cisco VPN installed on my personal laptop to work remotely.

  My laptop was originally Windows 8 and the VPN worked well.  When I downloaded Windows 10, when I connect to VPN access my internet disconnects.  I brought my laptop to my office and tried to connect it and it worked fine. One of the help desk technicians took the laptop home and installed new drivers and he claims that it worked for him. I brought my computer laptop home and tried to connect again to the VPN and it always drops my internet.

  There, any help would be appreciated.

  Pete

  Hello

  When connected this that exit comes from "ipconfig/all" and "route print" cmd?

  Try the box anyconnect client "preference - allow local 'lan'...» »

  Cristian

• How to configure an internet connection in Win7 via a smartphone USB =

  As I have full access to the Internet on a smartphone Nokia N97mini, how can I configure Win7 to use it as a digital modem? The 'add Internet' standard function treats the phone as an analog phone, which requires dialing a number.

  As far as I know, the smart phones that support this feature tethering do with the software, must be obtained from the manufacturer.  It is generally an ability that you have to buy extra in your data plan.

• ZoneAlarm blocked internet connection

  I use 6000 inspiring and have installed Zonealarm. For some reason I can't open internet explore without close zonealarm. Help, please! I thank in advance.

  
  

• Satellite 1130 set up an internet connection

  I am trying to set up an internet connection on my laptop using a disc of wanadoo, and all I get is an error message saying cannot establish a connection. tried about 6 times in total and still does not connect. The computer modem works fine, the only thing I thought I could be was when I tried first there came over analog telephone lines and digital, I can't get this screen up to change.

  Any ideas what could be wrong or how I can change the line defining?

  Post edited by: traceaphinea

  Hello

  Internet provider wanadoo is not known to me, but if you use their software you should contact them. They should have enough experience with own products. Each laptop manufacturer is responsible for the operation of the equipment that must operate at will with pre-installed software. Other problems are different and you should try to clarify with the internet service providers.

  I recommend to remove this software and try to set up the internet connection using the Windows settings. To configure the internet connection with modem is very simple and if you know this number and the password should not be any problem.

• Share internet connection - WRT610N support

  Hi all

  I'm looking for help.

  What I want to achieve:

  (1) I want that all my devices wireless - including my Philips TV - share media on the wrt610N using the 610N as my primary router.

  (2) I have a Thomson Speedtouch780 (my ISP, they call it the KPN Experia box). This device connects to the internet and is also a wireless routerwith. I want that all devices use this connection to access the internet.

  I configured the WRT160N cable to my PC and a cable for the Thomson router. It works perfectly: my PC wireless can I connect tot the WRT610N and I can access the internet...

  Now I want to disconnect the WRT610N router Thomson: I want it to be a wireless link (so I can put the art610 in a more central location). How to do this?

  My WRT610 parameters are:

  Basic configuration:

  Internet connection type: automatic configuration - DHCP active

  IP address: 192.168.0.1

  DHCP server: enabled

  Start IP address: 192.168.0.2

  IP address range: 192.168.0.2 to 51

  Basic wireless settings:

  5 GHz wireless settings:

  network mode: mixed

  Network name: Corleone_media

  SSID broadcast: enabled

  2.4 GHZ wireless settings:

  Network mode: mixed

  network name (SSID). Corleone

  SSID broadcast: enabled

  My Thomson parameters are:

  IP; 192.168.1.254

  Active DHCP server

  Starting IP address: 192.168.1.70

  Interface-information         Interfacegroep: LAN

  TCP/IP-configuratie         Adres van SpeedTouch: 192.168.1.254/24 Eerste adres van DHCP: 192.168.1.70 Laatste adres van DHCP: 192.168.1.253   Auto-IP: People with disabilities DHCP server: Activated

  Fix. A wireless as the WET bridge connects two cables ethernet via a wireless link segments. The RAIN will connect to your wireless router.

• Internet connection ASA 5512

  Hello

  I am new to networking and I have a framework problem 5512 ASA firewall. The problem is that I can not configure the internet connection inside my network.

  I created both LAN and WAN interfaces with the public IP (security level 0) with the ip address of 192.168.35.4, the security level 100. In fact, we replace the old router, and should take its address. I added 0\0 static route for my default gateway, and I am able to ping Google DNS server for the router, but impossible to the computer on the network. The network switch is also present on 192.168.35.254.

  For the purposes of the test, I changed the WAN IP address to computer connected to it with IP 192.168.99.2 192.168.99.1, and when I try to ping to the LAN interface, it does not return a ping.

  I'd appreciate any help.

  I thinl it's your acl global_access.

  You have not applied to an interface with the access-group command.

  If it applies to all interfaces that includes the LAN interface as well as the WAN interface.

  Then add ICMP in there or remove the acl if you want the apply to all interfaces.

  Jon

• DV7-2230SA after Downgrade XP Internet connection problem

  Hello.

  I tried to downgrade a DV7 2230SA to XP using the guide posted on these forums (http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and/General-XP-Downgrade-Guide-for-HP-Laptop...

  I managed to integrate the SATA drivers in the XP installation, and then continued to install the drivers for the chipset, MS - UAA and graphics. But when I install the network drivers to connect to the Internet via an Ethernet cable, are all I get messages saying that it is 'absorbing network address' and later that "this connection is limited or not connectivity", which means that I can't access the Internet.

  The Ethernet cable is good as it works on my desktop PC.

  I use Windows XP Professional SP2.

  Here are the drivers I installed in order:

  Chipset - filename "infinst_autol.
  MS-UAA-MS-UAA for XP (file name "kb888111")
  Graphics - ATI Mobility Radeon 4530 / 4570 (filename "8-12_xp32_dd_ccc_wdm_enu_72271")
  Network - Realtek PCIe GBE Family Controller (name of file "PCIE_Install_5794_05212012")

  I also tried other drivers LAN as "PCIE_Install_5760" and "sp38329" without success.

  I thought that maybe it could be because I had not installed the modem driver, but I have since discovered that this model is an internal modem, so it cannot be that.

  There is another network card present, listed as "1394 adapter", but the use of this single or uninstall has no effect. He returned in any case after the reboot.

  My Windows Firewall is disabled, as is my Kaspersky Internet Security.

  If I need to install some other drivers first, as my audio drivers? Or I have to configure my Internet connection in some way, for example by specifying an IP or MAC address?

  I'm puzzled, and I would appreciate any advice you guys could provide.

  Thank you.

  Hello:

  Try the XP driver for your NETWORK card wired directly from Realtek. Select the automatic installation XP version (to halfway to the bottom of the list).

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  Paul

• Connection to a VPN server enterprise, via an existing Internet connection - PPPoE

  Hi, I want to buy a router "EtherFast Cable / DSL VPN Router with 4-Port 10 / 100 Switch (BEFVP41) ' there is only one question: can I connect to the Internet on the PPPoE connection and use this connection to connect to the VPN server of your company through PPPoE or IPSec?

  You can connect to the Internet via the PPPoE connection on your router.

  If you use a VPN client software to connect to the secure your company network, there is usually a remote VPN server inside waiting to accept a connection of employees outside the corporate network.  All Linksys routers support VPN pass through and work with these types of connections. The only time that you need VPN Tunnel to the capabilities of the BEFVP41 is if you manually configure a secure VPN connection between two physical locations.

• Send all VPN traffic and the other end it blocks Internet

  Hello

  I wonder if I can get a RV042 VPN Tunnel to a RV082 and in the RV082 block all traffic on the internet that comes form the computers that are behind the RV042.

  Something like this:

  Remote PC-> RV042-> VPN-> RV082-> firewall RV082 (block internet traffic, allow intranet traffic)

  Thank you very much

  Oliver

  The scenario you describe should be doable with a pair of RV042 and RV082, where all traffic is transmitted by RV042 to RV082. What you need is to configure an access on RV082 rule to deny the RV042 subnet HTTP traffic to ALL (internet).

• VPN to use remote internet connection

  Hello

  I'm trying to access a Web site in the Venezuela that is blocking connections from outside Venezuela (official results of the presidential elections Sunday, which are publicly). I have access to remote control a computer running windows 7 to the Venezuela, but I don't want to use remote desktop as connections every time I want to visit this Web page.
  I remember that my school provides VPN access so that we can access documents and others during off-campus research and thought I could use VPN Windows anyway.
  I managed to create the VPN connection using VPN Windows clients/server, but it only allows me to access the internet. If I uncheck the option 'use remote gateway', while my local internet connection will always be recognized as outside the Venezuela. How can I activate the remote computer access to the internet for my local system connected VPN?

  Hello

  The Microsoft Answers community focuses on the context of use. Please join the professional community of COMPUTING in the TechNet forum below

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

• delete a block - my computer won't let me use google chrome as a browser. It indicates that the internet connection is not available.

  When you use the internet, my virus detector asked if I would allow google chrome to download a newer version. I clicked on the decline, and then my internet has stopped working. I finally got back on, but now my computer won't let me use google chrome as a browser. It indicates that the internet connection is not available. I was able to use other browsers, but not Google. I tried disabling my firewall to see if it would work then, but it still doesn't work. Any suggestions? I'm afraid, that I blocked it somehow. Thank you!!

  Hello

  I suggest you post your question in the Google Chrome forums here: http://www.google.com/support/forum

  This looks like a problem with this specific program and not with Windows. I hope this helps!

• How can I configure my Internet XP connection so that it will automatically connect to my WiFi (wireless) without asking me the password whenever I connect?

  How can I configure my Internet XP connection so that it will automatically connect to my WiFi (wireless) without asking me the password whenever I connect?

  original title: automatic Wifi connection

  Hello

  By default, Windows XP attempts to connect to networks without wires in the following order:

  1. Available networks that are in the list of network preferred (by order of registration)
  2. Preferred networks in the list proposed (by order of registration)
  3. Other networks according to selected advanced settings

  Check out these articles and check if that helps:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/wireless_networking_overview.mspx?mfr=true

  To connect to an available wireless network

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/wlan_client_connect.mspx?mfr=true

  To set up automatic wireless network configuration

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true

   

  5 steps: how to set up your network wireless home

  http://www.Microsoft.com/athome/organization/wirelesssetup.aspx

• VPN internet connection hangs after disconnection with tunnel of private clients

  I have to use a customer Cisco VPN (private tunnel) and due to the company safety Windows Remote Desktop.  This stop my normal internet access and the limit to a public internet connection "unidentified".  After that I closed the Office remotely Win and disconnect the Cisco client, my PC back to my normal internet connection, but it remains unavailable until I have unplug my normal connection and reconnect.  Is there a setting to Win 7-32 that will force the Cisco to get totally tunnel or a framework that will automatically fully my connection internet normal House?

  Hello

  The question you have posted will be well suited in the TechNet community. Click on the link below.

  http://social.technet.Microsoft.com/forums/en-us/categories/