E260 wont turn on its own or connected to the computer

Similar Questions

• Pavilion dv7 - 4183cl laptop turns off its own

  My Pavillion dv7 - 4183cl laptop turns off its own without any warning or error messages and then restarts asking power on the passsord, etc. I am running Windows 7 Home Premium. Occurrences are more frequent over time.

  The first thing I would check is your laptop fan. You hear it works while the laptop is on, or it is disabled? If the fan fails, the laptop overheats. To protect themselves, the laptop turns off. It could also be that you have little dust blocks the air fan. The best option is to have someone to disassemble the laptop and clean, but some people have managed with the help of compressed air. The problem with this is that it blows back into the laptop. Perhaps vacuum?

  A farily common problem with most laptops is the integrated graphics processors. Over time, the GPU becomes disattached from the motherboard. If this happens, the laptop will be closed or does not start at all. Generally however, there isn't a lot of attention if that is the case, the computer stops working one day.

• Get 'no scanners were detected. If a scanner is installed, make sure that it is turned on and connected to the computer and try again. "

  Original title: Windows Fax & Scan

  Hello, I just bought a new printer (Canon MG2450), and every time I try to scan something an error comes out.

  The error that says:

  No scanners were detected. If a scanner is installed, make sure that it is turned on and connected to the computer and try again. For more information about adding or troubleshooting scanners, see Help and Support.

  the printer is powered on and connected. I tried searching the Internet and I tried the TWAIN_32 and everything is good.

  What can I do?

  Daniel Capelle

  The scanner came with a CD to install the software?  Some more recent does not come with a CD, you must go to the Canon Website and you get the software.

• My Explorer Microsoft touch does not connect to the computer (Win 8 and 7 or iMac)

  I bought a touch of Explorer Microsoft wireless mouse and cannot understand why the mouse does not connect. The small usb dongle is recognized and the mouse turns works. The optical light is blue and the touch sensor clicks when I run my finger on it. Nothing happens when I press any button of the mouse (without interaction with the computer). It almost seems like its not even connected to the usb dongle. I tried to find out what's wrong with it or with Windows. The mouse itself doesn't simply plug the usb dongle or on the computer at all. It is not a Bluetooth mouse, so there is no button to connect or sync.

  Hello

  As it seems to be a hardware problem, you can check the link for the Microsoft Hardware supported:

  http://www.Microsoft.com/hardware/en-in/support

• Perform a hard reset when you are connected to the computer?

  Hello

  my iPod Touch G 6 seems to have momentarily buggy so I connected it to the computer, after he had died and needed a charge. He didn't start the loading of the iPod screen, so I did a hard reset while it was still connected to the computer. When he turned his back, I had to enter the password on the iPod to unlock the screen before you start synchronizing with the computer.

  Desire to do harm to the iPod? I accidentally unplugged before ejecting several times, so I'm just scared.

  Thank you

  Jesse

  You have no damage to the iPod. If you disconnect the iPod is communicating with the computer, then you can alter the iPod and a restoration will probably be necessary,

• I lost connection on the computer like many light wireless wireless router.

  I've got three Kindle and a laptop computer, more my PC connected

  Original title: I lost my WiFi connection at home in light of the route for the wireless is not lit.

  Hi geraldthorpe,

  Thanks for posting your query in the Microsoft Community. It seems that you have no internet connection on the computer. We can get this fixed number by systematically. It can be frustrating for you. But, don't worry, we're here to help.

  We start with a few questions-

  (1) what is the version of Windows installed on the computer?

  (2) you are able to connect to Internet via LAN cable?

  (3) are other computers at home able to access Internet?

  (4) do you get any error code or error message?

  (5) have you made changes on the computer?

  I would like more information about the issue.

  Method 1-

  As a general rule, if the wireless light is not on the router means that the ability of routers to transmit wireless is lost.

  The router has generally, 4 types of fires.

  Power - number 1

  Test - number 2

  Wireless - number 3

  Internet - number 4

  Numbered LAN are turned on only if a network cable is connected.

  If the computers are connected wirelessly, all the lights except the indicator light should light up.

  I wish you perform a reset and a cycle of power to the router.

  Reset the router-

  You must locate a set PIN size behind the router and press the reset button with a pointed object for 10 seconds. Now, release the button and wait for the lights to come back.

  Note If the wireless light is back on.

  Power cycle-

  I wish that you unplug the router from the power outlet main and plug it back again.

  Check if the problem persists.

  Method 2-

  I would have you look at the article-

  Network convenience stores

  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Method 3-

  I would have you look at the article-

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Wireless and wired network problems

  http://Windows.Microsoft.com/is-is/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  We know if you need help. We will be happy to help you.

  Thank you.

• Cannot delete files and music always there but not display upward when I connect to the computer?

  Hi all

  Recently, I had a lot of problems with the music does not or don't play not I decided to delete all my e260 music and start again.  That's where the real problem started.

  For some reason I can't delete three of the albums on my player.  Each of the albums have what appear to be corrupted in them files. My computer does not recognize the file type and file extension is given so I don't know what they are.  Each file "appears" to 4 GB in size but that may not be appropriate for my e260 is obviously only 4 GB in size!

  Whenever I try to delete them I get an error message reading "cannot delete file: cannot read the source file or disc»

  I tried to update the firmware, reset e260 to factory default settings and made 'restore' thingy (where you hold registration and plug it into the computer, etc.) and these files are still there.

  After reading this thing of disk checking on this forum, I did this.  I was then able to remove two of the albums, but when I tried to delete the third album renamed 'a' and the damaged file shows 0 bytes in size, but I still can not remove.  However, I can move it to the folder music to any other folder.  I just can not remove!  When I do, I get an error message saying "cannot delete f: cannot find the file specified. '.  Be sure to only specify the path and the correct name.

  After all that I started my e260, and now I find that 2 other albums are always on it, even if they do not display any where when I connect it to the computer.  I can see and read these albums on the drive, and they seem well, they do not appear to be there when I plug it into the computer and look for them in windows Explorer.  The music folder is not hidden also.  These two albums are not part 3 albums that I could not remove, they are actually part of the new substance started sort of all these problems with the music does not and is not only now that they are the display upwards and play but are not appear when connected to the computer!

  I know it's probably not a lot of information but can someone tell me how to fix this?  If not, can I just format the * bleep * thing or I'll then have an e260 dead?

  See you soon,.

  PKFFW

  PS: Sorry for the long windedness of this post.

  Format will not remove the firmware, which is the operating system of the Sansa. It removes only the content that you have added. It will go back to what it was when it was new out of the box.

  MTP does not matter if you have never used it. The ghost album can be just a list remains in your database file. Nevertheless, we must get rid of this corrupt file, so Format is probably your best option.

  For what it's worth, to connect with the PSG, your computer needs Windows Media Player 10 or 11 is installed. XP comes with WMP 9, so he will not see the Sansa in MTP mode. unless you have updated.

• Sansa E280 going to update the database when it is connected to the computer

  Hello

  Just at the moment where I was getting things straightened on my drive and everything was working fine, I plugged my E280 on my computer and it says "Refresh database" on the player and my computer does not see the E280.

  I've been looking around on the forum, and there are so many different options to try (of: delete the SYSTEM folder, which I was told not; to turn off the drive and engaging the hold button and the button to rewind when connecting to the computer, etc., which I tried ~ nothing; take off Firmware and put one on; do something in Recovery Mode) , which I have no idea how do; etc.).  Sorry, but I hope you get my point... What do I do?

  Thanks for any help once more.

  Thank you clu31355.  I tried the very first thing that you said ' put in operation and allow it to update the database (if desired) before you connect. "and voila - it worked.

  These Sansas seem to be quite ticklish - who knows what will happen?

• BlackBerry Smartphones Priv - connection to the computer as a drive with cable...

  You can connect the Priv a PC with the cable to access as a drive, especially for access to the SD card?   I had assumed would be immediate, easy, but the laptop does just not see it connected...?

  Some good news.

  Finally, I can get it to connect, but better as "Mount SD card", do not use Android file transfer.

  Certainly, there are only going to transfer different files Android app link provided in the MTP option in the phone under settings, buffer, top right options - USB connection to the computer, I had to kind of work, but I think it's a one-way arrangement therefore does not allow fiddling with files or data on the SD card.

  With the option of mounting SD, its worth knowing that the phone is not yet recognized, you need to pass options while its connected, so when switching back to Mount SD, it appears suddenly!

  I managed to move some files autour, and if I drop in the DCIM folder, Camera leader, they then appear within the app Photos, without the need to got to the unit records.

  Is worth knowing when you're connected, more, but not all of them simply disappear with the handset, but all are in their proper place, moved or otherwise, 30 seconds or more after the disconnection.

  Question NEXT, related to this, but could start anew thread; In my photos, I always kept a photograph or a scan of my passport, driving licence and stuff, amazing how much it is useful.  Priv does not read this map file, even if its same region in Photos.  The Passport can be pdf, is it possible to move files between the laptop and Priv autour so that it can read the docs and other things or is it possible to create a file on the SD card where the docs can be submitted and read by the priv...?  Indeed, where are the docs on Priv?  Ive schedules of my son on the map, but they do not seem to appear anywhere in the private and they are the .docx files.

  Thank you.

• Internet does not connect unless it is directly connected to the computer

  This problem occurred yesterday.

  Internet has suddenly stopped working. Things were going to turn power off, then on and distributed. I did check the lights on the modem and the router, but they were all working well. I have plugged on both computers. This does not solve it. I called Charter to see if there was a failure. Unfortunately, it's a message auto troubleshooting which I have materialized with. He had me hang my modem directly to my computer. This solved my problems of the internet.

  I went to sleep for the night in the hope that the internet, or what the question was, would fix itself. He did not. The internet still works only if it is directly connected to the computer.

  There are other people who need to use the internet here. (Invoices, work schedules and other) So maybe it's very much a problem. Any other computer or phone, will work in the House.

  What is a router problem or a cable, or...?

  If your connection works when you plug the modem but not through the router, this indicates a problem with the router.   This could be a hardware failure or a configuration problem.  A problem with the cable between the modem and the WAN port on the router is possible, but unlikely.  It wouldn't hurt to check if she.  Most routers have a reset button recessed.  I suggest that you reset the router and reinstall as if new.  If this fails, you probably need to replace the router.

  Depending on your technical knowledge, you can also log in to the router and check the status information.

• I can't connect to the computer 0xc000021a error

  Original title: 0xc000021a.

  Good if one day I have reset my computer because he had firewall frozen in the middle of the screen. After rebooting once the hp screen would have happened to the top of the screen would go black. The error screen would come to the top and say that the error was 0xc000021a and once we're back to zero it does again and again and I can not sign in or anything. Safe mode does not help. need help ASAP please

  Computer

  Windows 8 HP portable 32-BIT

  Hello

  Check with HP support, their documentation online and ask questions in the forums on
  known problems with your model (or similar).

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ------------------------------------------------------------------------------------------------

  The problem may be caused by hardware such as hard drive or wiring issues among many others.

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the Office
  and the splash screen.

  The link below is for Windows 7 but it will also provide information that is useful when
  works with Windows 8/8.1 if you need to translate a few commands Windows 7
  in those for Windows 8/8.1.

  Translate these methods Windows 8/8.1 (there is little real difference):

  Resolution of the blue screen in Windows 8/8.1 errors
  http://Windows.Microsoft.com/en-CA/Windows-8/resolve-Windows-blue-screen-errors

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or can not
  Start Windows. (applies also to Windows 8/8.1)
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  =============

  STOP: 0XC000021A

  Can be a difficult problem to solve, and you will indeed need to technical assistance from a real computer
  Shop (that makes its own internal service) or the system manufacturer's support.

  Bug Check 0xC000021A: STATUS_SYSTEM_PROCESS_TERMINATED

  Bug STATUS_SYSTEM_PROCESS_TERMINATED control has a value of 0xC000021A. This means that an error has occurred in a subsystem essentially user mode.

  Important info if you received a STOP Code

  If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error.

  If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  These actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  Parameters STATUS_SYSTEM_PROCESS_TERMINATED

  The following settings are displayed on the blue screen.

  Parameter	Description
  1

  A string that identifies the problem

  2

  The error code

  3

  Reserved

  4

  Reserved

  Cause

  This error occurs when a subsystem of mode user, such as WinLogon or the Client Server Run-Time Subsystem (CSRSS), irremediably compromised and security can not be guaranteed. In response, the operating system goes into kernel mode. Microsoft Windows cannot run without WinLogon or CSRSS. Therefore, it is one of the rare cases where the failure of a user mode service can stop the system.

  Incompatible system files can also cause this error. This can happen if you restored your hard disk from a backup. Some backup programs may skip restoring system files which they determine are in use.

  Resolution

  Run the kernel debugger is not useful in this situation because the error occurred in a user mode process.

  Resolve an error in the user-mode device driver or system, third-party application service: Because the bug 0xC000021A control occurs in a user mode process, the most common culprits are third-party applications. If the error occurred after the installation of the new or updated device driver or service system, third-party applications, the new software should be removed or disabled. Contact the manufacturer of the software on a possible update.

  If the error occurs during the system startup, restart your computer, and then press F8 to character-based menu that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time. If the error is not resolved, try to manually remove the offending software. If the system partition is formatted with the (FAT) file allocation table, use a MS-DOS boot disk to access the hard disk of the computer. If the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or remove the defective software.

  If the defective software is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file. If a room newly installed if material is suspected, remove it to see if that fixes the problem.

  Try running the emergency recovery disk (ERD) and allow the system to repair any errors that it detects.

  Solve a problem of file system do not match: If you have recently restored your hard disk from a backup, check if there is an updated version of the backup/restore program available from the manufacturer. Make sure that the latest Windows Service Pack is installed.

  STOP: 0XC000021A<-- read="" this="">
  * 1314.html http://www.faultwire.com/solutions-fatal_error/Status-System-Process-terminated-0xC000021A-

  ========================================================

  Windows 8/8.1 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8 and 8.1
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8 and 8.1
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  If you have need of a system repair disc or other methods:

  How to create a "system repair disc" (CD/DVD) in Windows 8 (not 8.1)
  http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

  How to create a recovery USB in Windows 8/8.1

  http://www.eightforums.com/tutorials/5132-recovery-drive-create-USB-flash-drive-Windows-8-a.html

  How to create a Bootable USB or a DVD with an ISO of Windows 8 or 8.1
  http://www.eightforums.com/tutorials/2227-create-bootable-USB-DVD-Windows-8-ISO.html

  How to start on the "System Recovery Options" in Windows 8/8.1
  http://www.eightforums.com/tutorials/2269-system-recovery-options-boot-Windows-8-a.html

  Boot to the tip "Startup parameters" in Windows 8
  http://www.eightforums.com/tutorials/4924-advanced-startup-settings-boot-Windows-8-a.html

  =======================================================

  You may need to carefully check the hard disk for errors (don't forget to inspect the cable
  much as you can).

  Don't forget to look for RootKits that can survive a format and install of Windows.

  TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
  It will display all the infections in the report after you run - if it will not run changed the name of
  TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
  check with the other methods below.
  http://support.Kaspersky.com/viruses/solutions?QID=208280684

  ====================================================

  After the drive verification RootKits inspect the disc and the wiring. Then carefully
  check the hard disk for errors using the advanced methods and the producers
  Diagnostic utilities.

  These are much more efficient methods to check the disc.<->

  At the prompt of the Windows 8/8.1 disk (boot from it):

  Chkdsk /f /r
  (Space after k and before / f and before /)

  RESET

  sfc/scannow
  (Space after c and before /)

  RESET

  =====================================

  For even more detailed control:<-- manufacturer's="" diagnostic="">

  (The old 302602 links isn't now valid for Diagnostics links).

  Manufacturer diagnostic utilities - run one to your hard drive
  http://www.techsupportforum.com/hardware-support/hard-drive-support/462298-no-IDE-device-found.html

  Corrected list dated 06/09/2010

  Fujitsu hard drives: utility of diagnosis here
  http://www.Fujitsu.com/EMEA/products/HDD/

  Hitachi hard drives: utility of diagnosis here
  http://www.HitachiGST.com/support/downloads/

  IBM hard drives: use the Hitachi utilities

  Toshiba hard drives: use Hitachi or Maxtor utilities

  Maxtor hard drives: Diagnostic Utilities here (now SeaGate)
  http://www.Seagate.com/www/en-us/support/

  Quantum hard drives: use the Maxtor utilities

  Seagate hard drives: here Diagnostic utilities
  http://www.Seagate.com/www/en-us/support/downloads

  Conner hard drives: use the Seagate utilities

  Hard drives Samsung: utility of diagnosis here
  http://www.Samsung.com/global/business/HDD/

  Hard drives Western Digital: utility of diagnosis here
  http://support.wdc.com/product/download.asp?lang=en

  Trial versions of one of these 'might' help.

  SpeedFan
  http://www.almico.com/sfdownload.php

  HD Tune
  http://www.hdtune.com/

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" and="" devices="" for="" it :="" bicycle="" -="" mark="" twain="" said="" it="">

• Palm TX connects to the computer via WiFi for Hotsync

  I tried the network Hotsync on all my computers, XP, Vista 32 and Vista 64 (which started the whole attempt) and the device fails to connect to the computer, even if I set the IP address.

  My wireless network see the Palm and I am able to access the Internet through it, but it does not connect to my computer. Any suggestions?

  Here is my Wifi Hotsync help file:

  WiFi HotSync with a TX

  1. on your PC, locate the Manager HotSync (small HotSync icon in the lower tray of the right tool on a Winbox). Click top and check 'Network', then click again and select Setup.

  2. choose the network at the top tab in the window that opens and locate your HotSync name in the list. Make sure it is checked.

  3. press the button of TCP/IP and look for the IP listed for "main PC address. Write it down.

  4. turn on the Wifi on your Palm and you connect to your router.

  5. on your Palm, select the HotSync program and press the word "Network" over the HotSync icon in the middle of the screen. Below, enter the IP address that you noted in step 3. (Include periods!).

  6. tap the HotSync icon big above the IP address and hang in there!

  7. If you stand and nothing happens try a HotSync cable, then retry the HotSync Wifi. Sometimes, information is to be transferred from your PC once you check the network option. Also, don't forget to watch for any activity of firewall ask you questions about "HotSync.exe tries to access your hard drive" etc. You may need to define a rule to allow him to.

  On your TX, check these settings in the drop in Hotsync:

  Modem Sync: network

  LanSync: LANSync

  Network configuration: (Wifi should be listed as one of the networks)

  WyreNut

  Message edited by WyreNut on 02/11/2008 10:59

• My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  Sync your iPhone, iPad or iPod touch with iTunes using a WiFi - Apple...

• iPod classic connects to the computer

  Hello

  I have an iPod classic, since 2005.

  It will charge from the grid, but when you plug it into the computer it does nothing... Does not make a noise, does not load... Nothing, only thing that happens is that when you disconnect the computer screen lights illuminates... tried all USB ports, still is not, tried 3 computers, does not work on any...

  so I tried 2 more iPods, an iPod classic in 2004 and it worked fine. Tried an iPod nano of 2007 once again absolutely worked well...

  really annoying me now that I want to sync music on the classic...

  tried resetting the iPod, tried to run in the other mode keeping the home button and menu, press the button home-and play... None of them worked either

  Jake

  When you "recharge sector" (which I assume means an adapter of any), are you using the docking cable that you use with the computer?  When you connect iPod from 2004 and 2007 iPod nano to the computer, you use the same USB docking cable used with the iPod in 2005?

  Is the power supply adapter ("hands") accomplice of old load powering FireWire supported, not USB load?  Accessories older load use FireWire instead of USB charging, which has a different voltage and uses different "pins" on the dock connector.  An iPod from 2005 (probably a 5th generation "video" iPod) to connect to the computer via a USB port, but it can recharge using the USB or FireWire power.

  If you can confirm that the port host USB cable to connect the iPod in 2005 is good, my guess is that the 2005 iPod dock connector will not properly connect to USB power.  It can be worn or damaged.  Therefore, it does not connect to the USB port on the computer.  However, it always connects to FireWire, so she received the adapter (which feeds the FireWire).

  Use a flashlight to look inside the iPod dock connector, to visually check for damage, corrosion, dust or debris.

• How long it take restore iphone when connecting to the computer

  How long it take restore iphone when connecting to the computer

  Is based on the amount of data to restore. How long do we have?

  GB