East-redirection of possible connection when the routing service is disabled?

Similar Questions

• Windows Search draws BIG > 3GB WINDOWS. EDB file, even when the search service is disabled!

  Search for Windows XP generates a very large WINDOWS. Index EDB file (> 3 GB).  At first, it seemed to be a 5 GB OUTLOOK indexing. PST file *, however, I disabled the indexing service and unchecked the "allow Indexing" box on all disks and uncontrolled all items in the window "Indexing Options".  I rebooted and deleted WINDOWS. File EDB.  A few minutes later, however, the Search Service icon reappeared in the system tray and a WINDOWS. EDB file is growing again on my drive.  The "Indexing Options" dialog box indicates the number of items indexed by incrementing upward, but the window "Included locations" is empty.  While I wrote this paragraph, that 'disabled' Indexing Service has indexed 12 799 points, so even though I followed the steps to turn it off, it is still something indexing.)  How can I disable this service completely so that it will not build a WINDOWS. EDB file at all?

  This PC is a Lenovo ThinkCentre M55 running Windows XP Pro version 2002 with Service Pack 3.  2 GB of RAM, Dual CPU 6300 @ 1.86 GHz

  The bottom line question:

  How can I remove WINDOWS. EDB file and make sure that it does not return & grow?

  My thanks in advance!

  -HDL

  New York City

  Hi HDL - NYC,.

  I suggest that you remove the KB940157 update that is associated with indexing and check if you can remove the indexing file.

  (a) click Startand then click run.

  (b) copy and paste the following command in the Open box and then press ENTER: appwiz.cpl

  (c) click to select the Show updates check box.

  (d) KB940157 -click, and then click Remove.

  (e) click Finish to restart the computer after the uninstall is complete.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Need RV016 VPN connect when the router is turned on?

  Restarted my RV016 (e.g. after a power failure) the gateway to gateway VPN do not connect.  I have to go the VPN router summary page and click on connect to get them started.  Is there a way to make this happen automatically?

  In the advanced configuration of the tunnel section, if DPD and Keep Alive options are checked, RV016 will try to reconnect automatically.

• MacMini don't auto connect to the preferred wireless network when the router reboots

  My MacMini is located to join my favorite wifi network. Where I stay, there is usually a power failure close to a minute or two during the day.

  My setup is such that my MacMini running 24 x 7 with a backup uninterruptible but my router (AirPort Express) turns off during the power outage. When the router goes off, my Mac disconnects from the network which should, but now when my router turns, the MacMini reconnect to the preferred network.

  It shows the network preferred list, and when I manually click on this subject, it reconnects immediately without asking for password. But this will not happen automatically.

  If I restart my MacMini it reconnects very well. The problem occurs only when my MacMini is but my router restarts.

  To reproduce this problem on your side, just turn off your router and once your Mac disconnects from the network back on the router. See if your mac reconnects to your wifi fine.

  Any solution or advice for this problem?

  Thank you.

  Please test after taking each of the steps that you have not already tried it. Stop when the problem is resolved. Back up all data before making any changes.

  1. If possible, test at another network, such as a public access point or hotspot created by a mobile phone. Some Wi - Fi routers are not fully compatible with Apple devices. More specifically, the security mode for the network, as shown in the network preferences window, should be 2 personal WPA or WPA 2 Enterprise. If the router doesn't support either of these modes, it should be replaced with another.

  2. make sure that the network is on the list of favorites by following these instructions. It is important to read the article, as it is the starting point for further efforts to solve the problem. If you skip any step, the problem cannot be resolved. Make sure that the box marked

  Remember this computer has joined the network

  is checked.

  3 follow the instructions in this article to support.

  4. reset the PRAM.

  5. take note of all your parameters of connection Wi - Fi in the network preferences pane, then remove the connection in the connection list and re-create it with the same settings. This by clicking on the icon of the lowest sign from the list of connection, select Wi - Fi as the interface in the form that opens. Select join the other network in the network name menu, then select your network. Enter the password when you are prompted, and then save it in the keychain.

  6. in the menu location at the top of the network preferences window, select Edit locations. A sheet will fall. Click on the plus sign to create a new location. Give it the name of your choice. In the new location, set up the Wi - Fi service with the same settings that you used before. Click on apply and test.

  7. run the Keychain Access application. Find and remove all the network password AirPort elements that refer to the network. Make a note of the password first.

  8 turn off the Bluetoothand the test.

  9. reset the system management controller.

  10. This step should not be necessary, but he has been advised by the Apple Support in some cases, apparently as a solution for a bug. Open the energy saving pane in system preferences. If necessary, click the lock icon in the lower left corner to unlock the settings. When prompted, enter your administrator login password.

  Select the Power Adapter tab and uncheck the boxes marked

  Continued access to the Wi - Fi network

  and

  Enable the NAP...

  If it is present. Then, if the computer is a MacBook, select the stack tab and uncheck the box

  Enable the NAP...

  11. reinstall OS X.

• I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  It will be useful.

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Firefox prevents the connection from the router

  WRT120N router Linksys-Cisco, Firefox 22.0

  I discovered that my router rejects all attempts at connection (192.168.0.1, 401 authentication failure "browser can not perform authentication or authentication failed") when you browse to it from Firefox. It allows the connection when the attempt is made of Chrome.

  I remember having long ago something similar with Firefox, but resolved by disabling the option "say it me not to follow the sites", following what connections made; just looked and it is still not verified - if this isn't it.

  I looked a the packet capture and the password IS sent to the router, but it rejects the connection.

  Any ideas?

  "BUT IT WORKS CORRECTLY BOOTED IN SAFE MODE."
  Which prompted me to check the extensions.
  I called, guess what... TAKE STEPS TO TRACK ME.

  (Why is there such an extension if it is built in function?)

  Disabling, allowing the router to connect! I don't know why twice now, try to activate Do not not track eliminated the possibility to connect to the router... but this is the solution.

• Windows 7 Dell computer laptop connects to the router, but the internet connection is spotty/slow

  I recently installed a new Comcast wireless gateway, which includes a built-in router.  My Ipod and Ipad work perfectly with this new router connection.  My Dell laptop, however, connects to the router without a problem, but it surfing the internet very slowly and sometimes can't access it at all.  The router connection remains strong during these periods of power failure, however.  I don't get online no problem when I connect directly to the router/modem with an Ethernet cable.  Network troubleshooting does not detect a problem, I have released/updated my IP address, and made sure I had updated drivers.  The issue still [persists.  Any input on what to try next?

  Hello Scot,

  Thanks for posting your question in the Microsoft Community forums.

  The description of the problem, I see that the Internet connection is very slow on the computer.

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  Maybe there's a chance that some network settings, start services application or a third party or a security software restricted it to connect properly and is responsible for the internet connection is slow.

  I suggest you to follow the steps below and see if it helps.

  Method 1

  I suggest you try the procedure described in the following Microsoft Article and check if it helps.

  Internet Explorer is slow? 5 things to try
  http://Windows.Microsoft.com/en-us/Windows/help/Internet-Explorer/slow-five-tips-to-boost-performance

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  Method 2

  If the problem persists, I suggest you to follow the steps described in the following Microsoft tutorial and see if it helps.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Why is my Internet connection so slow?

  http://Windows.Microsoft.com/en-us/Windows/why-Internet-connection-slow#why-Internet-connection-slow=Windows-7

  Method 3

  If after performing more high question method persist, try to perform the clean boot and temporarily disable security software and then check the speed of the Internet.

  Step 1: Perform the clean boot

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

  Note: See "How to reset the computer to start normally after a boot minimum troubleshooting" to reset the computer to start as usual after a repair.

  Step 2: Temporarily disable security software.

  Disable the antivirus 

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.

  Method 4

  Since then, the issue is not resolved by disabling the security software, Windows Firewall could be the next possibility. So, I suggest, temporarily, disable the Windows Firewall and check if the problem persists.

  Refer to the following steps:

  1. Press the Windows key + R, type firewall.cpl , and press ENTER.
  2. Click turn Windows Firewall on or off. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. Click turn off (not recommended) Windows Firewall under each network location that you want to stop trying to protect, and then click OK.

  Caution:

  You should not turn off Windows Firewall unless you have another firewall is enabled. Turning off Windows Firewall may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers. You must reactivate as soon as you have completed troubleshooting.

  For more details, you can see the article mentioned below.

  Enable or disable Windows Firewall

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• 9.3.4 disabled wifi on an Ipad, but it connects to the router. Just don't download at all

  IPad was working fine, but I've updated to 9.3.4. Now Wireless does not work. Shows connected to the router, but nothing happens, but say unable to connect to the server, error trying to access the internet or by mail. Also turn continuous flashing VPN gray to green, then again, but we have never set up a virtual private network. Don't know if it is connected. Have you tried

  1 disconnection / reconnection to 2 routers that work very well for other devices

  2 reset wireless via settings > general > reset > reset network settings and then hang up again

  3 airplane mode on, wait a few minutes, then shut off again

  Overall, the router will connect to any time, we put the password, but there is no transfer of data. 3 other devices work fine with the router. Don't know where to go from here, or if it is possible to back out from the upgrade. Anyone else having this problem? A research increase the same problem.

  Thank you

  Anything that causes the problem is not specifically 9.3.4, which fixes just a security breach. Have you tried to restart routers?

• 15 - r074TU: laptop does not connect to the router

  Day sum... .my laptop (model No. 15r074TU) with window 8.1 does not connect to the router that is D-link

  I uninstalled my driver reinstalled again, but it didn't work... even if I formatted my laptop, reconfigure the router and... done with all possible measures to overcome this problem, but have ultimately failed. Please suggest ways to tackle this problem as soon as possible...

  Follow the wizards in the following forum sticky and troubleshooting.

  http://h30434.www3.HP.com/T5/notebook-wireless-and-networking/common-fixes-for-wireless-connectivity-issues/m-p/4831601#M86871

• iMac connects to the router of Linkysys WRT1900ac

  I am trying to help a friend get his iMac 12.1, that is running 10.11.4, to connect to a new Linksys WRT1900ac router.  The router is a novelty in this House, is in the same room of 10 x 12, as the computers listed below, and the installer was using the Linksys recommends the method, which is to let the Linksys to make adjustments.

  Here are its configuration;

  The router is connected to a cable modem, ISP and the following devices are connected to the router and works well;

  Via ethernet

  Windows 10 PC

  AT & T cell phone extender

  Ooma VOIP

  Wireless

  iPhone

  iPad

  Notebook PC

  While troubleshooting my MacBook 5.1 also allows to connect without problems to the Linksys router.

  Note that her iMac connects without problem to the wifi network Netgear Guest unprotected from its neighbor.  I also installed in his room my 1st generation Airport Express, which has added a second wifi network but without access to the internet and his iMac connect without problems to this wifi.

  Here are the steps I took to try to solve this problem, and they were unsuccessful;

  ➔ Scanned for malware/adware with Malwarebytes and found nothing.

  ➔ Ransacked after the files in/Library/Preferences/SystemConfiguration and restarted

  com Apple.Airport.Preferences.plist
  NetworkInterfaces.plist
  Preferences.plist

  ➔ When the previous did not work I trashed all the files in the folder/Library/Preferences/SystemConfiguration except "com.apple.boot.plist', which would not remove and rebooted

  ➔ Created a second user account and still not able to connect to the Linksys router

  ➔ Repaired permissions

  ➔ Created a new location in System Preferences > network and added the OpenDNS addresses and in the material value MTU 1453

  ➔ restarted in safe mode and not still could not connect

  Firmware on the router Checked ➔, which is updated

  ➔ Reset SMC

  ➔ reinstalled El Capitan via the App Store

  That's all I could think about.  I'm puzzled.

  I checked the router and everything seems ok, but I'm no expert.  There may be something I'm not contagious.  I have seen that he has no MAC filtering set up in the router, so this isn't everything.

  Please tell me if there is something that I'm on.  Is there something in the router, that I need to change?  There are other files in the Mac, I need to delete?  Is there any other troubleshooting steps I can take to identify this problem.

  Any help would be appreciated as it is a total mystery to me.

  There are a lot of variables, but start with some basic info. So on her iMac, if you click the wifi at the top right, you can see his router listed?

• Unable to connect to the router WLan - Satellite L300D

  Please help me so that I have still a few hairs left!

  I installed WLAN driver on my laptop Satellite L300D with Vista Home installed.

  I see my network in the available connections, but when I go to connect, it will not connect.

  My other two desktop computers can connect to the router without a problem.

  Any suggestions?

  Thank you
  Neil

  Hello

  I think that you didn t try updates. Right?
  Therefore, my first recommendation would be an update of the BIOS and driver WLan.

  Check the current version of the BIOS that is available on your laptop. If the latest version has been released then update the BIOS.
  In addition, to download the latest WLan driver from the Toshiba WLan portal and to update:
  http://APS2.toshiba-tro.de/WLAN/

  On this Wlan site, you will find three different WLan drivers for three types of WLan cards. First check your wireless network card, and then use the right driver!

  See you soon

• Samsung S6 connects to the router but no internet

  When I switched to xfinity I bought a C6300. I had problems with the first not allowing my NAS to connect so I exchanged against another. My phone would connect to the router and work fine for awhile then lose Internet connectivity. The only way to get it back is to reboot the router. I tried several different units, and I am now on a C3700. The problem still exists and seems to be deteriorating. All of the suggestions.

  I solved my problem by replacing the Netgear with a Zoom. It was the only one that I could find who said it would work with Android. I hope that Netgear will get things straightened.

• Unable to connect to the router (even after reset)

  I'm really frustrated, and I hope that this community can provide an answer. After all the hype around this router, it is he who gave me the most trouble.

  About a month and a half... completely randomly it seems to me, I could not connect to the router more. Not through intellectual property, routerlogin.net/com...nothing. It just says: cannot display the page. I did everything I could possibly think, tried all of the suggestions I could find here and elsewhere and still nothing would work.

  I finally did a hard reset and obviously lost all my settings... and RIGHT AFTER the hard reset after upgrading the firmware, I can't connect to the router again. This could be the cause? Is there a way around it?

  The router worked fine until about a month and half ago. Then I stopped being able to connect to the admin page. Several resets hard did nothing.

  I ended up RMA'ing it and the new replacement works fine (for now).

• Slow WLAN connect to the router - Satellite Pro A200

  I have a Satellite Pro A200 - after starting the laptop she used to find the router wireless in good time, but now it seems to have slowed on the right and it may take a few minutes until 1/2 hour phone to find the router!

  This doesn't seem to be a signal problem because when the router is found that I get a signal strength full 5 bars. Connection to the laptop the router with a cable shows that no problem also that the connection and internet access is no problem.

  I do not understand why the laptop won't find the router faster and you would appreciate the help in the understanding of the problem and how to resolve the situation.

  I don't have a lot of technical knowledge so please keep in mind when replying

  Thank you

  Mike

  Hi Potter (maybe Harry?)  ;)

  You can easily find what WiFi card has been installed in your laptop.
  More details can be found in the *-> network adapters Device Manager *.
  Check this out and you'll know what driver WLan is required!

  _Regarding the question with your BIOS; _
  This error is known to me, always happens if you n t unpack the BIOS package correctly!

  What you need is a WinRAR or WinZip program.
  I prefer WinRAR and it helps to unpack all of the BIOS update.

  If you use the Vista operating system please check that another thread of forum on the same issue;
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=123140𞄄

  Good luck