easy question for all

Similar Questions

• Question for all developers, who participated in the offer of Playbook 2012

  Hello

  Ive got a question for all the developers who participated in the BB PB 2012 bid. Have you received E-mail about your shipping information (giving your address for shipping) immediately with enamel, that said, that your application has been approved? or did you get it later?

  Thank you.

  A few days later.

• Can't access the internet - easy question for the experts! (ASA 5510)

  Dear all

  I can't access internet from my home network!

  I don't know why!

  Router:

  Ethernet f0/0 interface: 195.xxx.xxx.17/29 (to connect to the router) IP

  THE ASA NETWORK

  The external interface e0/0: 195.xxx.xxx.18/29 IP (to connect to the router)

  Internal interface: e0/1: IP 10.10.100.1 mask 255.255.252.0

  The ASA configuration

  ASA Version 8.0 (2)

  !

  ciscoasa hostname

  domain.com domain name

  enable encrypted password xxxxxxxxxxxx

  names of

  DNS-guard

  !

  interface Ethernet0/0

  nameif Interface_to_cisco_router

  security-level 0

  IP address 195.xxx.xxx.18 255.255.255.248

  !

  interface Ethernet0/1

  nameif Int_Internal_domain

  security-level 100

  address 10.10.100.1 IP 255.255.255.0

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  management only

  !

  xxxxxxxxxxxxx encrypted passwd

  boot system Disk0: / asa802 - k8.bin

  passive FTP mode

  clock timezone WEST 0

  clock summer-time WEDT recurring last Sun Mar 01:00 last Sun Oct 02:00

  DNS domain-lookup Interface_to_cisco_router

  DNS domain-lookup Int_Internal_domain.com

  DNS server-group DefaultDNS

  Server name 195.22.0.136

  Server name 195.22.0.33

  domain.com domain name

  permit same-security-traffic intra-interface

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  Interface_to_router_Cisco_access_in list extended access allowed object-group TCPUDP any any eq field

  Interface_to_router_Cisco_access_in list extended access permit tcp any any eq www

  pager lines 24

  emergency logging level list Registo_eventos_william

  emergency logging list level Registo_eventos_william class vpn

  asdm of logging of information

  exploitation forest-address recipient [email protected] / * / critical level

  management of MTU 1500

  MTU 1500 Interface_to_router_Cisco

  MTU 1500 Int_Internal_domain

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 602.bin

  don't allow no asdm history

  ARP timeout 14400

  Global interface (Interface_to_router_Cisco) 101

  NAT (management) 101 0.0.0.0 0.0.0.0

  Access-group Interface_to_router_Cisco_access_in in the Interface_to_router_Cisco interface

  Route 0.0.0.0 Interface_to_router_Cisco 0.0.0.0 195.xxx.xxx.17 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 10.10.100.0 255.255.255.0 Int_Internal_domain

  http 10.10.10.0 255.255.255.0 management

  http 195.xxx.xxx.16 Interface_to_router_Cisco 255.255.255.248

  http 192.168.1.0 255.255.255.0 management

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  No encryption isakmp nat-traversal

  Telnet 10.10.100.0 255.255.255.0 Int_Internal_domain

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 10.10.100.20 - 10.10.100.250 Int_Internal_domain

  dhcpd dns 10.10.100.2 195.22.0.136 interface Int_Internal_domain

  dhcpd lease interface 345600 Int_Internal_domain

  dhcpd domain domain.com Int_Internal_domain interface

  enable Int_Interna_domain dhcpd

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  class-map inspection_default

  match default-inspection-traffic

  Thanks in advance

  MP

  Hi MP,.

  Based on the configuration below, only traffic since the possible management interface to access the internet.

  Global interface (Interface_to_router_Cisco) 101

  NAT (management) 101 0.0.0.0 0.0.0.0

  You must include your inside interface in the nat statement if you want to have the traffic within the internet go.

  Example:

  NAT (Int_Internal_domain) 101 0.0.0.0 0.0.0.0

  Kind regards

  Arul

  * Rate pls if it helps *.

• Easy question for the literate of photoshop

  Hi I'm new to photoshop and I'm trying to teach me how to use it, I had bought a few photoshop actions and did very well, and then all of a sudden the entire column disappeared from the right side of the screen, how can I bring back? Thanks in advance!

  Just thought out, go to the menu bar, then windows and click actions. They're back, woohoo!

• Another easy question for a beginner

  Example: Pig picks up Apple with pig.addChild (apple);

  If, say, a bird wants the Apple but the pig there:

  If (bird.hitTestObject (apple)

  {

  bird.addChild (apple);

  Apple.x = 0;

  Apple.y = 0;

  }

  and the pork and the apple touch the bird, Apple remains with the pig.

  If an object is a child of another object like the pig, it's (the Apple in this case) dependent on only this object (the pig)?

  Thanks for any input

  Shiim

  You are welcome.

  p.s. Please mark this thread as answered.

• Easy question

  When file sharing / information wirelessly between the computer connected to my network via my home wireless router, not information trip computer to the router to the second computer or information travels from computer to the router via the modem and then return via the modem to the router and then to the second computer?  I hope that it will be an easy question for someone.  Thank you.

  File on your network as you transfer the describe does not mean the modem, router and computer, any computer.

• HP Deskjet 3520e: question for HP Deskjet paper jam 3520e all-in-One Series

  I feel when the paper jam in the printer. I tried all the solutions they say to try to release the jam, but it did not work, and the message I get on the printer's "clear transport jam", I would like to know if there is something else I can try out the book?

  Hi@NIcoleSann22

  Thank you for visiting the HP Forums . One-stop shop for all kinds of solutions, tips and settings for your questions/problems.

  For the best experience on HP forum, see our Guide to HP Forums to learn more.

  On the printer paper jam. Is this fair?

  I will definitely help you.

  Try the steps from the link below and check to see if that clears the error on the screen.

  http://HP.care/2dyjpZ7

  Let me know if this helped

  Resolv_S

  Happy to help you. I work for HP
  
  Please click "Accept as Solution" if you feel my post solved your problem, it will help others find the solution.
  Click on ' Bravo Thumbs Up ' to say 'Thank you' to help!

• Easy way to change the label of the field for all user interfaces?

  How a client would change a label field for all user interfaces that use this field or attribute, which is not really a translation?

  What I have found seems to be that we would need to edit Resource Bundles and it will be much easier in version 8:

  1. the information on Resource Bundles in https://blogs.oracle.com/fadevrel/entry/translating_your_customizations section has this key passage:

  It is a standard open sector (OASIS) XML file with the extension .xliff format and store translated values for strings used by the ADF running. The general process is that these values are exported from the MDS, modified manually and then imported into the new repository. This must be done by an administrator, either via Enterprise Manager or WLST orders according to the screenshot below. It is detailed on the merger application Extensibility Guide.

  2. this blog announcement also says that it will be easier in version 8:

  Currently planned for version 8 is what we call the UI (UI) text editor. This tool will allow the mounting of all the text on the pages and merge request forms. This will provide a search based on an expression or a Word, say 'Worker' and will allow it to be adjusted, tell 'Employee', which then updates all the resource bundles that contain.

  3. I found video, How to customize field labels , but it seems that it is a label of the user interface at the same time...

  WIlliam, Yes, and we have a documentation and/or videos on this feature when R8 is available.

• For CS6, is there an easier way to redirect all my files and folders for all programs?

  Hey people adobe, Im wondering, I know you can configure each preference individually, but I want to redirect all caught space, storage of brushes and etc for all my programs in an another disc as volume change c / e /. Is there a way to do this with a program to make it easier? I don't want to accidentally delete files that are not all adobe programs.

  The reason is I don't want anything else then store programs on the SSD, and theoretically, I want the other disk, so it can run faster.

  There is no global option for this.

  Mylenium

• SQL in Question actually. Select the items for all 12 months

  I am creating a notification request where I SUMMARIZED all of the amounts in the database for all 12 mount and come up with a result even if it isn't a amount totaled. I created a table called monthsInYear that has the ID (unique identifier) 1-12 and the months of Jan - Dec. I want SUM to the amount per month and arrived to the top with 12 results (one per month).

  I tried the query below, but sometimes with only 1 month and all amounts amounted to him.

  March

  484714.13

  I use:

  SELECT monthsInYear.month, IFNULL (SUM (income.amount), 0) AS amount

  OF monthsInYear

  Income ON EXTRACT(MONTH FROM income.dateAdded) = monthsInYear.monthID LEFT OUTER JOIN

  WHERE income.orgID = 10031

  AND the YEAR (income. DateAdded) = '2011'

  ORDER BY EXTRACT (MONTH FROM income.dateAdded) CSA

  Can someone tell me what I am doing wrong. I much prefer something like:

  January 3000

  February 3000

  March 4000

  April 0

  Maybe 5000

  June 6000

  July 5465

  ....

  But when I run the present, it gives me total for only the months which have in total and not 0 for those that go up as null. Any ideas?

  ....

  Also tried

  SELECT m.month, IFNULL (SUM (i.cost), 0) AS amount

  I have getExpenses LEFT OUTER JOIN monthsInYear m

  ON m.monthID = EXTRACT (MONTH FROM i.dateAdded)

  WHERE orgID = 10031

  AND YEAR (i.dateAdded) = '2011'

  GROUP BY m.month

  ORDER BY EXTRACT (MONTH FROM i.dateAdded) CSA

  There are two problems. First of all, in your join tables are reversed. A LEFT JOIN returns all the records in the left table (spending) even if there is no matching record in the table to the right. What you want, it's the opposite. If the month table should be on the left side of the JOIN:

  ...

  OF monthsInYear m LEFT JOIN getExpenses i m.monthID = EXTRACTION (i.dateAdded MONTH)

  Second, when there is no corresponding record in the expense, the column values will be null. So as soon as you use one of the fresh fields in your WHERE clause, that is to say

  WHERE i.orgID = 10031

  AND YEAR (i.dateAdded) = '2011'

  ... these missing documents are deleted, because a null value is never equal to what it is. So you are denying the outer join altogether. You must move these conditions in the JOIN clause instead:

  SELECT m.month, IFNULL (SUM (i.cost), 0) AS amount

  MonthsInyear LEFT OUTER JOIN getExpenses m I have

  ON m.monthID = EXTRACT (MONTH FROM i.dateAdded)

  AND i.orgID = 10031

  AND YEAR = 2011 (i.dateAdded)

  GROUP BY m.month

  ORDER BY m.month

• How to get an extension of the dictionary for all users in a Citrix environment?

  Hi all

  Under title, I'm looking for a way to get out a dictionary of Firefox (specifically the English (British) of https://addons.mozilla.org/en-US/firefox/language-tools/) to all users in a Citrix environment. Comprehensive silent installation is absolutely best. Because following a recent installation of Firefox users report that this spell check is not working, what appears as a result there is no dictionary to check the spelling on the facility.

  It's in a corporate environment, running 6.5 XenApp hosted workstations to multi-server Windows 2008 R2 Enterprise x 64, the installed Firefox info below as collected by the add-on troubleshooting pulled from the browser in the test environment with the same characteristics.

  So far, I have tried what follows from this link: http://kb.mozillazine.org/Installing_extensions

  "A whole installation will install an extension in the directory of the application rather than in a profile so it will be available to all users. To perform a whole installation, you must not activate as within your Mozilla application installation file. Instead, download and save this record and make sure you close the application completely.

  Then follow one of the following options:

     Copy the .xpi file into the <installation directory>\extensions folder. When you start your Mozilla application again, it displays an installation dialog, asking "The following items were found in your Extensions folder. Do you want to install them?" "
  

  Although it seems that the < installation directory > \extensions folder no longer exists at the given location. Find a path of the < installation directory > \browser\extensions but seems it does not behave as said here that I have not received all of the guests. I hope that this method is still applicable in some way and I am just not aware of how this is currently supposed to be handled, but not sure if it is a dictionary rather than a typical add-on will have no effect on the installation overall how can be reached.

  Have also tried to http://forums.anandtech.com/showthread.php?t=2268437 , which seems a pretty basic option, but this would have not only to a lot of work to do on a per user basis, but there are also restrictions in place to prevent access to the records of users AppData.

  Finally I was looking https://support.mozilla.org/en-US/questions/740545 to push this point across: the les parametres parameters configuration, then use the method above to enforce this on the user end, but did not find anything me.

  Any help/advice/shots of elbow in the right direction would be greatly appreciated.

  It might be easier to extract the files of two dictionary (.dic and .aff) of archive XPI (ZIP) and place the two files in the folder of Firefox profile for the dictionaries available for all users.

• Cannot install Windows Easy Transfer for update to Windows 7

  I am running Vista Home Premium 64-bit sp2 and upgrade to Windows 7 Pro. I know I need everything back up, install 7 and then restore my data and programs. When I install Windows Easy Transfer, it downloads very well, then on run I get 'Stand Alone Windows Update installation', then "Looks For Updates" and then "update applies to my system" and nothing, fact. I made sure I download the Easy Transfer for Vista 64 bit, but I'm stumped. Any ideas?

  Hello
   
  Windows Easy Transfer is an integrated application available on all editions of Windows Vista or Windows 7. It is not necessary to download explicitly on the Vista computer.
   
  To access Windows Easy Transfer, try the following steps.
  1. click on start, type Windows Easy Transfer and click transfer files from Windows in the list.
  2. follow the instructions in the wizard and complete the tasks successfully.
   
  Check out these links for more information:
  1 explore the features: Windows Easy Transfer:
  http://www.Microsoft.com/Windows/Windows-Vista/features/easy-transfer.aspx
  2. the transfer of files and settings: frequently asked questions:
  http://Windows.Microsoft.com/en-us/Windows-Vista/transferring-files-and-settings-frequently-asked-questions
  3. install, reinstall, and uninstall Windows:
  http://Windows.Microsoft.com/en-GB/Windows/help/install-reinstall-uninstall
   
  Let us know if you have any questions, so that we can clarify.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• A question for Steve and thanks!

  First of all, thanks to Steve for this great comparison to hearing other applications http://forums.Adobe.com/thread/511864?TSTART=0

  I'm new to computer recording (semi experimented with other types) and looking for a program as a result of my needs, review of Steve led me to try hearing with a friend recently and wow, what amazing one audio editor!

  I have some questions about the editing of audio capabilities Auditions, it is superb and more intuitive program out there.

  Only, I have a few questions about the Auditions multi-track editing capability, or rather, the ease of use (interface) because it's something we could need more experience to be able to assess.

  My question is about his ability to make 'easy' and intuitive multi-track on a SMALL number of tracks, all THE AUDIO, song and audio files as virtual synth samples, loops, a shots etc...

  If for example the publishing Arrangement of say 6 to 12 channels, which is what I use in general.

  Are things like: Moving song autour, moving loops, stretching/change and reorganization of the different segments of the song easy to do?

  What is the actual record, like that of putting in place to make punch, many taken, is such included or better yet intuitive things like other programs of the multitrack recording?... I don't get in a lot of plugins and midi, very little or not at all.

  I'm tired so I'm going to cut short my questions, there was one more I forgot, I'll come over later to make sure that I have tyepd everything correctly, tahnks for all help!

  jcs35 wrote:

  Are things like: Moving song autour, moving loops, stretching/change and reorganization of the different segments of the song easy to do?

  What is the actual record, like that of putting in place to make punch, many taken, is such included or better yet intuitive things like other programs of the multitrack recording?... I don't get in a lot of plugins and midi, very little or not at all.

  Well, take in order... to move the song is relatively easy - like any other thing, really moves. Loops of move in the same way, essentially. You can group clips and move the groups in the same way as the individual clips. In addition, you can lock the groups and the individual clips, and which tends to reduce the errors (that are easy to do with any software!)

  When it comes to real record, make simple tracks is easy - set up their bonus and off you go. Do dropins works very well in what concerns the record, and it's pretty easy to set up as well, but Adobe, being believers in the welfare State, make it very difficult to throw unwanted or unused takes - this has annoyed a user where he wrote an app to work around, you can find here. As an organizational tool, mediasweeeper has been developed with the feedback from users, so there is a good chance he will do exactly what it says on the box. If I was regularly stops, I would like to use, it's course.

  What's the intuitive multitrack Editor? I would say yes, it is. It is ideal for the production of music? No, it's not (for reasons already mentioned). One of his great strengths (in AA3.0) as far as I am concerned is just inaudible fades chained with a perfect match between can be obtained very easily - for me, as an editor of classical music, the ability to do that is of fundamental importance. Weaknesses generally appear more when you massively clips or tracks in a session - it may become, to say the least, slow in some of its operations compared to other music software. But the audio quality remains excellent, and sometimes I am not convinced that the other software - manage ProTools, for example, is known to have a less powerful mix engine (this is why there are continuous sales of passive mixers for her - individual track mix outputs using one of these sounds much cleaner).

  However, I would say that if you have about 6 tracks mainly music acoustics or loops, then hearing would be a very good tool to use, because at this level of loading is wrong your system to cane too. It is also interesting to note, with regard to the system use, that you can lock the securities you have applied processing, which reduces the continuous load reading and help generally things going. Blocking can also be cancelled if you want to change anything on a track - nothing is set in stone until you do a mix.

  Is there any other software that would achieve the same things just as easily and relatively cheaply? Well, I think that Reaper it would manage, but personally I think that Reaper is a bit geeky (what with all these ridiculous range operations, etc.), and in addition it is nowhere close to the Publisher hearing. Personally, I wouldn't be comfortable with Reaper in front of visitors, but I will quite happily use hearing when they are present.

• Once for all - please

  Hi all
  
  I used CF for several years now and bought Flex as soon as he was released. In my process to understand how Flex manipulated remote objects for CF, I decided to use the Assistant Creation of CF for Flex that creates all kinds of beautiful CFCS and other things to connect to a database and the CRUD data inside. OK all well and dandy on the local machine, works very well, I'm impressed! This is until I try to download the application for my shared server (HMS) and I get all sorts of error messages as cryptic:
  
  error ID (mx:rpc:Fault) #0 = 0
  faultCode = "Client.Error.MessageSend"
  faultDetail = "Channel.Connect.Failed error."
  NetConnection.Call.Failed: HTTP:Status 500 "
  faultString = "send failed".
  message = "faultCode.Client.Error.MessageSend faultString:"Send Failed '"
  error faultDetail:'Channel.Connect.Failed
  NetConnection.CallFailed: HTTP: status 500 "name ="Error ".
  rootCause = (Object) #1
  code = NetConnection.Call.Failed.
  Description = "HTTP: status 500".
  Details = "' http://www.MYDOMIAN.com/flex2gateway/ ' level ="error""
  
  So I read the DOCs and read all the blogs I can find on the subject, but nobody can give a clear answer as to why I can't do this job on a shared server if I can make it work on my local machine, hell, I can even tap into the MySQL database on the server shared via Flex builder. I use HostMySite.com with CF package if that helps.
  
  If it's just a matter of something on my end to host that I need them to set up for me it would be nice to know, or if I simply can't use Flex and CF together on a server all shared together. It would be nice to know. But for all the hype Flex did and how easy is it supposed to be to create an app with CF, I wonder why someone can't answer this question once and for all. I know that others have posted to this and many other forums asking the same things I am. Is it too ask one of the Gurru of Adobe Flex, or anywhere else for that matter to help us?
  
  Not everyone wants to run their own server, and I think Adobe would have kept that in mind when creating Flex, and how he'd shared servers.
  
  So please if someone can help understand it please let me know.
  
  Thank you

  halodev:

  When I had my problems, I didn't have to touch the con. Correct XML file their and I initially worked in my localhost too. So, I don't know.

  I only did the site Flexstore-like as a study project. It is not real for any client project, and so I don't mind share. It might be a good idea for you to check the code just for comparison with yours; If you want, send me an email and I'll send you my mxml files.

  Carlos
  [email protected]

• 1 model for all the links of pseudo-device

  Hello group, this should be an easy question, but I'm stumpped for some reason any. While trying to keep my style sheet, organized and as small as possible, I want to have a style for all the events of a hyperlink in a specific. class. I thought I could do this by creating simply 1 style .class {a} and who would be the appearance of all the States of this hyperlink.
  
  Basically I don't want my style sheet stretch downwards when having the same exact style for different binding events properties. I just have 1 style all States active, hover effects, etc., but I don't know how the style should look:
  
  I tried and has some variants beside her, but nothing has done what I wanted.
  
  . Class a: link: hover: visited: active: visited: hover {}
  do-family: Arial, Helvetica, without serif.
  do-size: 8pt;
  color: #003366;
  padding-top: 5px;
  padding-right: 5px;
  padding-bottom: 0px;
  padding-left: 5px;
  text-decoration: none;
  }
  
  Any help is greatly appreciated.

  This:

  > .class a: link: hover: visited: active: visited: hover {}

  must be:

  . Class a: link, .class a: .class visited, a: hover, .class a: active {}

  and providing your HTML looks like this:

  -Darrel