Easy VPN

Similar Questions

• Cisco easy VPN + loopback interface. static ip address for the client

  Good day people.

  I have a couple a question and answer on which I can't google for a period. BTW I maybe simly use bad aproach to choose keywords.

  Thus,.

  (1) is it possible to assign the same IP to the same customer every time that it authenticated, preferably without using DHCP? Definely im sure it is possible, but can't find match configuration examples (my camera's 1921 Cisco IOS 15.0.1).

  (2) is it possible to assign the dynamic crypto map to the loopback interface (to make EASY VPN Server accessible through two interfaces - maybe you recommend another approach instead?) - that I move the map workingcrypto of int phy loopback - I can not connect with reason "SA Phace1 policy proposal" not accepted

  Hello

  (1) you can attach to the same IP to the same username using RADIUS

  (2) If you have 2 outside interfaces

  Then, you would use

  mymap-address loop0 crypto card

  int gig0/0

  crypto mymap map

  int g0/1

  cryptp map mymap

  By doing so, the local address would actually be the loop0 but Cryptography card HAS to be applied on physical output interfaces

  See you soon

  OLivier

• Easy vpn remote

  I have a router 2611 with ios:c2600 - I - mz.120 - 10, DRAM/FLASH is 26624 K / 6144 K

  and the compact flash is 4966520.

  It would support the easy vpn remote feature? If this isn't the case, what IOS/DRAM/FLASH might be appropriate?

  Hello

  Use feature Navigator find IOS appropriate for different platforms:

  http://Tools.Cisco.com/ITDIT/CFN/JSP/index.jsp

  HTH

  Sangaré

• Cannot access the internal network with Cisco easy vpn client RV320

  I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?

  Thank you

  Hello

  1. is the firewall on the active Windows 7 computer? If so, please disable it

  2. can you check that you get a correct IP address in the range of the POOL of IP configured?

  3. When you perform the tracert command to access an internal server, it crosses the VPN¨?

  4. is the tunnel of split giving you access to internal IP subnets defined?

  5. on the RV320 you see the user connected and sending and receiving bytes?

  Don t forget to rate and score as correct the helpful post!

  David Castro,

  Kind regards

• With an interface easy VPN client only

  Hi guys,.

  I have an ASA 5505 configuration as simple Client VPN. Current configuration uses two interfaces: inside and outside. I tested the connection to the server and works very well.

  For reasons of site specific I'm limited to a single interface, you can call it inside, lan, whatever. So I need to connect clients to the remote site behind this interface and also use it to reach the easy VPN server. Is it possible in the first place?

  Of course, I will put the default route through the Interior of interface and another router will provide the Internet connection.

  It's so hard to make it work you should consider the answer is no.

  Specifically, you need to have one inside and outside interface or EasyVPN will not come to the top.

• Easy VPN between two ASA 9.5 - Split tunnel does not

  Hi guys,.

  We have set up a site to site vpn using easy configuration vpn between ver 9.5 race (1) two ASA. The tunnels are up and ping is reached between sites. I also configured split tunnel for internet traffic under the overall strategy of the ASA easy vpn server. But for some unknown reason all the customer same internet traffic is sent to the primary site. I have configured NAT to relieve on the side of server and client-side. Please advise if no limitation so that the installation program.

  Thank you and best regards,

  Arjun T P

  I have the same question and open a support case.

  It's a bug in the software 9.5.1. See the bug: CSCuw22886

• The anyconnect vpn easy vpn Remote communication problem

  Hi team,

  I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment
  topology:

  (1) VPN Tunnel between branch HQ - That´s OK
  (2) VPN Tunnel between Client AnyConnect to HQ - that s OK

  The idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached.
  Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
  in this way, the communication is OK, but just for a few minutes.

  Could you help me?
  Below the IOS version and configurations

  ASA5505 Version 8.4 (7) 23 (Headquarters)
  ASA5505 Version 7.0000 23 (branch)

  Configuration of the server easy VPN (HQ) *.

  Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1
  Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
  Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  Crypto map interface outside-link-2_map outside-link-2

  ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
  ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0

  internal EZVPN_GP group policy
  EZVPN_GP group policy attributes
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list ACL_EZVPN
  allow to NEM
  type tunnel-group EZVPN_TG remote access
  attributes global-tunnel-group EZVPN_TG
  Group Policy - by default-EZVPN_GP
  IPSec-attributes tunnel-group EZVPN_TG
  IKEv1 pre-shared-key *.

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Configuration VPN AnyConnect (HQ) *.

  WebVPN
  Select the outside link 2
  by default-idle-timeout 60
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
  AnyConnect enable
  tunnel-group-list activate

  tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
  tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0

  internal clientgroup group policy
  attributes of the strategy of group clientgroup
  WINS server no
  value of server DNS 192.168.1.41
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  ipconnection.com.br value by default-field
  WebVPN
  AnyConnect Dungeon-Installer installed
  time to generate a new key 30 AnyConnect ssl
  AnyConnect ssl generate a new method ssl key
  AnyConnect value Remote_Connection_for_TS_Users type user profiles
  AnyConnect ask flawless anyconnect

  type tunnel-group sslgroup remote access
  tunnel-group sslgroup General-attributes
  address vpnpool pool
  authentication-server-group DC03
  Group Policy - by default-clientgroup
  tunnel-group sslgroup webvpn-attributes
  enable IPConnection-vpn-anyconnect group-alias

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Hello

  communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA.

  When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic.

  I hope this explains the cause.

  Kind regards

  Averroès.

• Easy VPN configuration problems

  Hello

  I have 6.2 (2) Version PIX PIX 515E. I am trying to setup the easy VPN server to this topic. This pix not recognized the next line of the comand.

  1.

  Crypto-map dynamic 70 outside_dyn_map Road opposite value

  2.

  Crypto isakmp nat-traversal 70

  or isakmp nat-traversal 70

  3 tunnel-group

  is there a command line I can use inplace of them. I have also attached my config so I would be very grateful if someone could check and advice me what to do to raise this connection.

  Thank you

  Take a look at this:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080241a0d.shtml

  Yes nat - t is available on 6.3.x and above and no it is not enabled by default on the PIX / ASA. It is IOS.

  Please note if useful, cordially

  Farrukh

• Easy VPN server on 1811 configuration

  I'm trying to configure easy VPN server on my router from 1811 to allow remote users to access resources on our corporate network. I used the wizard to perform the configuration for the easy VPN, but when I test the VPN it fails to check the dependent components. He said to me that AAA authentication, authorization and Global Address Pool are all "not configured." I have configured AAA on MDS under additional tasks, so I don't know where I am going wrong. Any help is greatly appreciated.

  Brandon,

  the below URL - provide almost all the examples of configuration for the 18xx series.

  http://conft.com/en/us/products/ps5853/prod_configuration_examples_list.html

  HTH.

• Cisco 831 - easy VPN server

  Hello

  I am trying to create an easy VPN server on Cisco 831. When I "test" the easy VPN he said that it tested successfully, but when I try to VPN in the router of the built in Windows XP VPN client, I'm unable to connect.

  Does anyone have recommendations for how to configure easy VPN? I basically just selected all the default options. I was not able to find tutorials in the Cisco online documentation.

  Do I need to have the Cisco VPN client to connect to the Cisco router?

  Other thoughts?

  Your IP address pool you are trying to assign to remote users is part of your local network, which is not the best way to assign the ip address to the VPN Clients, and I've seen a lot of problems in the past were route it not forwards the packets to the client. This allows you to change the POOL of something other than your LAN. E.g. 192.168.1.0/24.

  Also, make sure that you re - configure your 102 ACL accordingly.

  Once you make changes, try to connect again and let me know how it goes.

  Kind regards

  Arul

  * Please note all useful messages *.

• Easy VPN server

  Hello

  I configured easy VPN server on Cisco 1841 & got a form of address IP VPN hen but unfortunately not able to access private or servers on the local network, address maybe because I can NATing.

  Please advice?

  I have attached the file of Configuration of the router.

  Kind regards

  Alain R.Aljabi

  Hello

  Need to get around the NAT for VPN IP address Pool. Please follow it below URL that explains how to work around NAT (static) with route map. This configuration should get your VPN works.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094634.shtml

  Kind regards

  Arul

  * Please note the useful messages *.

• 6500 and easy vpn client

  Can I connect a PC with easy vpn client with a vpn service module 6500?

  Are there examples in the Web?

  Take a look at the following link as there some configuration examples that should help you.

  http://www.Cisco.com/univercd/CC/TD/doc/product/LAN/cat6000/cfgnotes/78_14459.htm

• IOS Easy VPN Server / Radius attributes

  Hello

  I made an easy VPN server installation with a running 12.2 2621XM router (15) output T5. VPN Clients/users are authenticated against Cisco ACS 3.2 by RADIUS.

  It works fine, but there is a problem that I can't solve. Each user must have the same VPN assigned IP address whenever it is authenticated.

  The ACS sends the right radius attribute (box-IP-Address) back to square of IOS, but this address is not assigned to the client. The customer always gets the next available IP address in the local set on the router.

  How can I solve this problem?

  You will find the relevant parts of the configuration and a RADIUS "deb" below.

  Kind regards

  Christian

  AAA - password password:

  AAA authentication calls username username:

  RADIUS AAA authentication login local users group

  RADIUS AAA authorization network default local group

  crypto ISAKMP policy 1

  Group 2

  !

  crypto ISAKMP policy 3

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto identity hostname

  !

  ISAKMP crypto client configuration group kh_vpn

  mypreshared key

  pool mypool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac shades

  !

  mode crypto dynamic-map 1

  shades of transform-set Set

  !

  users list card crypto mode client authentication

  card crypto isakmp authorization list by default mode

  card crypto client mode configuration address respond

  dynamic mode 1-isakmp ipsec crypto map mode

  !

  interface FastEthernet0/1

  IP 192.168.100.41 255.255.255.248

  crypto map mode

  !

  IP local pool mypool 172.16.0.2 172.16.0.10!

  Server RADIUS attribute 8 include-in-access-req

  RADIUS-server host 192.168.100.13 key auth-port 1645 acct-port 1646 XXXXXXXXXXXXXXXX

  RADIUS server authorization allowed missing Type of service

  deb RADIUS #.

  00:03:28: RADIUS: Pick NAS IP for you = tableid 0x83547CDC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:28: RADIUS: ustruct sharecount = 2

  00:03:28: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:28: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  4, len 73

  00:03:28: RADIUS: authenticator 89 EA 97 56 12 B1 C5 C2 - C0 66 59 47 F7 88 96

  68

  00:03:28: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:28: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:28: RADIUS: username [1] 10 "vpnuser1".

  00:03:28: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:28: RADIUS: User-Password [2] 18 *.

  00:03:28: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/4 l

  in 108

  00:03:28: RADIUS: authenticator C1 7 29 56 50 89 35 B7 - 92 7 b 1 has 32 87 15 6

  A4

  00:03:28: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:28: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:28: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:28: RADIUS: Tunnel-Password [69] 21 *.

  00:03:28: RAY: box-IP-Netmask [9] 6 255.255.255.0

  00:03:28: RADIUS: Framed-IP-Address [8] 6 172.16.0.5

  00:03:28: RADIUS: [25] the class 37

  00:03:28: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:28: RADIUS: 2F 33 63 30 61 38 36 34 31 61 76 70 75 73 [3/c0a8641a 6F 2F

  /vpnus]

  00:03:28: RADIUS: 65 72 31 [1]

  00:03:28: RADIUS: saved the authorization for user 83547CDC to 83548430 data

  00:03:29: RADIUS: authentication for data of the author

  00:03:29: RADIUS: Pick NAS IP for you = tableid 0x82A279FC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:29: RADIUS: ustruct sharecount = 3

  00:03:29: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:29: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  5, len 77

  00:03:29: RADIUS: authenticator 13 B2 A6 CE BF B5 DA 7th - 7B F0 F6 0b A2 35 60

  E3

  00:03:29: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:29: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:29: RADIUS: username [1] 8 'kh_vpn '.

  00:03:29: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:29: RADIUS: User-Password [2] 18 *.

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/5 l

  in 94

  00:03:29: RADIUS: authenticator C4 F5 2F C3 EE 56 DA C9 - 05 D6 F5 5 d EF 74 23

  AF

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:29: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:29: RADIUS: Tunnel-Password [69] 21 *.

  00:03:29: RADIUS: [25] class 35

  00:03:29: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:29: RADIUS: 2F 34 63 30 61 38 36 34 31 61 2F 6 b 5F 68 76 70 [4/c0a8641a

  [/ kh_vp]

  00:03:29: RADIUS: 6 [n]

  00:03:29: RADIUS: saved the authorization for user 82A279FC to 82A27D3C data

  Assignment of an IP address via a server Raidus is currently not supported, even if your Radius Server is through an IP address, the router will ignore it and just assign an IP address from the pool locla. In fact, the pool room is the only way to assign IP addresses currently.

  On the only way to do what you want right now is to create different groups VPN, each reference to a local IP pool with an address in it. Then ask each user connect to the appropriate by their VPN client group.

  Yes, messy, but just try to provide a solution for you.

• Easy vpn server issues of Cisco 800 series.

  Hello.

  I want to deploy the easy vpn server on cisco 876 and 877 10 routers and access from a remote location (company headquarters). When I leave the firewall of the router off the vpn server works. When I turn it on it doesn't.

  Although I allow all traffic to my ip for example 80.76.61.158 I can't access the vpn server.

  I tried a place to let the firewall off and it worked fine.

  I use SDM to configure the vpn server. Any ideas what I can do with the cause of firewall I really can't leave it "open."

  Thanks in advance.

  It would be a good idea to paste the configuration of the VPN server to the firewall.

  Kind regards

  Kamal

• Easy VPN client

  Hi, I am building a vpn using an easy VPN server on 8xx adsl router and a remote client using xp pro.

  On the server side is set up but, when the documentation says "simple vpn client" This means that the client vpn 4.6 or 4.7 or 4.8 cisco vpn client? or is a particular software?

  Best regards

  Edgar Quintana

  In terms of support, customer of EasyVPN: customer equipment.

  As routers and PIX firewalls connected as a client on the side of the head. (which will be an EasyVPN server).

  The normal software clients are called VPN clients.