With an interface easy VPN client only
Hi guys,.
I have an ASA 5505 configuration as simple Client VPN. Current configuration uses two interfaces: inside and outside. I tested the connection to the server and works very well.
For reasons of site specific I'm limited to a single interface, you can call it inside, lan, whatever. So I need to connect clients to the remote site behind this interface and also use it to reach the easy VPN server. Is it possible in the first place?
Of course, I will put the default route through the Interior of interface and another router will provide the Internet connection.
It's so hard to make it work you should consider the answer is no.
Specifically, you need to have one inside and outside interface or EasyVPN will not come to the top.
Tags: Cisco Security
Similar Questions
-
How to put all through traffic the easy vpn client VPN server
Hi people
I want to ask you, how to put all of the server the easy vpn client VPN traffic through.
I mean, I have a server vpn at home, and if I connect to the vpn from outside server, to be with an IP address of my home.
There is the configuration up to now. Where is the problem?
ROUTER1 #sh running-config
Building configuration...
Current configuration: 5744 bytes
!
! Last configuration change at 19:51:18 UTC Wed Sep 4 2013 by cska
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
ROUTER1 hostname
!
boot-start-marker
usbflash0:CVO boot-BOOT Setup. CFG
boot-end-marker
!
!
!
AAA new-model
!
!
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
Service-module wlan-ap 0 autonomous bootimage
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-1604488384
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1604488384
revocation checking no
!
!
TP-self-signed-1604488384 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 04050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363034 34383833 6174652D 3834301E 170 3133 30383239 31313539
32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36303434 65642D
38383338 3430819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100CD 57 F1436ED2 8D9E8B99 B6A76D45 FE56716D D99765A9 1722937C F5603F9F
528E27AF 87A24C3D 276FBA1C A5E7C580 CE99748E 39458C 74 862C 2870 16E29F75
7A7930E1 15FA5644 D7ECF257 BF46C470 A3A17AEB 7AB56194 68BFB803 144B7B10
D3722BDD D1FD5E99 8068B77D A1703059 9F0578C7 F7473811 0421490D 627F25C5
4 HAS 250203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355
551 2304 18301680 141B 1326 C111DF7F 9F4ED888 EFE2999A 4C50CDD8 06 12301
03551D0E 04160414 1B1326C1 11DF7F9F 4ED888EF E2999A4C 50CDD812 300 D 0609
2A 864886 04050003 81810096 BD0C2B16 799DB6EE E2C9B7C4 72FEAAAE F70D0101
FF87465C FB7C5248 CFA08E68 522EA08A 4B18BF15 488D D53D9A43 CB400B54 8006
CB21BDFB AA27DA9C C79310B6 BC594A7E D6EDF81D 0DB7D2C1 9EF7251B 19A 75403
211B1E6B 840FE226 48656E9F 67DB4A93 CE75045B A986F0AD 691EE188 7FB86D3F
E43934FA 3D62EC90 8F37590B 618B0C
quit smoking
IP source-route
!
!
!
!
CISCO dhcp IP pool
import all
network 192.168.1.0 255.255.255.0
DNS-server 195.34.133.21 212.186.211.21
default router 192.168.1.1
!
!
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
license udi pid CISCO892W-AGN-E-K9 sn FCZ1530C209
!
!
username privilege 15 secret 5 cska $1$ $8j6G 2sMHqIxJX8MQU6vpr75gp1
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
Configuration group customer isakmp crypto VPNGR
vpngroup key
DNS 212.186.211.21 195.34.133.21
WINS 8.8.8.8
domain chello.at
pool SDM_POOL_1
ACL 120
netmask 255.255.255.0
ISAKMP crypto ciscocp-ike-profile-1 profile
match of group identity VPNGR
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
security association idle time 86400 value
game of transformation-ESP-3DES-SHA
set of isakmp - profile ciscocp-ike-profile-1
!
!
Bridge IRB
!
!
!
!
interface Loopback0
192.168.4.1 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface BRI0
no ip address
encapsulation hdlc
Shutdown
Multidrop ISDN endpoint
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
!
interface FastEthernet5
!
FastEthernet6 interface
!
interface FastEthernet7
!
interface FastEthernet8
no ip address
Shutdown
automatic duplex
automatic speed
!
type of interface virtual-Template1 tunnel
IP unnumbered Loopback0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
interface GigabitEthernet0
Description Internet
0023.5a03.b6a5 Mac address
customer_id GigabitEthernet0 dhcp IP address
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
!
wlan-ap0 interface
description of the Service interface module to manage the embedded AP
192.168.9.2 IP address 255.255.255.0
ARP timeout 0
!
interface GigabitEthernet0 Wlan
Description interface connecting to the AP the switch embedded internal
!
interface Vlan1
no ip address
Bridge-Group 1
Bridge-Group 1 covering-disabled people
!
interface BVI1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
local IP SDM_POOL_1 192.168.4.3 pool 192.168.4.245
IP forward-Protocol ND
!
!
IP http server
local IP http authentication
IP http secure server
overload of IP nat inside source list 110 interface GigabitEthernet0
IP nat inside source static tcp 192.168.1.5 3389 interface GigabitEthernet0 3389
IP nat inside source static udp 192.168.1.5 3389 interface GigabitEthernet0 3389
IP nat inside source static tcp 192.168.1.5 21 interface GigabitEthernet0 21
IP nat inside source static udp 192.168.1.5 21 interface GigabitEthernet0 21
IP nat inside source static tcp 192.168.1.4 3389 interface GigabitEthernet0 3390
IP nat inside source static udp 192.168.1.4 3389 interface GigabitEthernet0 3390
overload of IP nat inside source list 120 interface GigabitEthernet0
IP route 0.0.0.0 0.0.0.0 dhcp
!
exploitation forest esm config
access list 101 ip allow a whole
access-list 110 permit ip 192.168.1.0 0.0.0.255 any
access list 111 permit tcp any any eq 3389
access-list 120 allow ip 192.168.4.0 0.0.0.255 any
!
!
!
!
!
!
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
!
Line con 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
transport output pad rlogin udptn ssh telnet
line to 0
line vty 0 4
privilege level 15
preferred transport ssh
entry ssh transport
transportation out all
!
Thanks in advance
To do this you must make the following changes:
(1) disable split Tunneling by deleting the ACL of your configuration of the client group.
(2) enable NAT for VPN traffic by adding 'ip nat inside' to your virtual model of the client network to the ACL that controls your PAT.Edit: Theses are the changes to your config (also with a little cleaning):
Configuration group customer isakmp crypto VPNGR
No 120 LCD
!
type of interface virtual-Template1 tunnel
IP nat inside
!
no nat ip inside the source list 120 interface GigabitEthernet0 overload
!
access-list 110 permit ip 192.168.4.0 0.0.0.255 any
no access-list 120 allow ip 192.168.4.0 0.0.0.255 any
Sent by Cisco Support technique iPad App
-
Can I connect a PC with easy vpn client with a vpn service module 6500?
Are there examples in the Web?
Take a look at the following link as there some configuration examples that should help you.
http://www.Cisco.com/univercd/CC/TD/doc/product/LAN/cat6000/cfgnotes/78_14459.htm
-
Cannot access the internal network with Cisco easy vpn client RV320
I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?
Thank you
Hello
1. is the firewall on the active Windows 7 computer? If so, please disable it
2. can you check that you get a correct IP address in the range of the POOL of IP configured?
3. When you perform the tracert command to access an internal server, it crosses the VPN¨?
4. is the tunnel of split giving you access to internal IP subnets defined?
5. on the RV320 you see the user connected and sending and receiving bytes?
Don t forget to rate and score as correct the helpful post!
David Castro,
Kind regards
-
Help with 1921 SRI Easy VPN remote w / Easy VPN Site-to-Site access
I have two 1921 ISR routers configured with easy site to site VPN. I configured VPN each ISR ACL so that all networks on each site can communicate with the private networks of the other site. I have a 1921 SRI also configured as an easy VPN server.
Problem: when a remote user connects to the easy VPN server, the user can only access private networks on the site of the VPN server. I added the IP network that is used for remote users (i.e. the Easy VPN Server IP pool) to each VPN ACL 1921, but the remote user still cannot access other sites private network via the VPN site to another and vice versa.
Problem: I also have a problem with the easy VPN server, do not place a static host route in its routing table when he established a remote connection to the remote user and provides the remote user with an IP address of the VPN server's IP pool. The VPN server does not perform this task the first time the user connects. If the user disconnects and reconnects the router VPN Server does not have the static host route in its routing table for the new IP address given on the later connection.
Any help is appreciated.
THX,
Greg
Hello Greg,.
The ASAs require the "same-security-traffic intra-interface permits" to allow through traffic but routers allow traversed by default (is there no need for equivalent command).
Therefore, VPN clients can access A LAN but can't access the Remote LAN B on the Site to Site.
You have added the pool of the VPN client to the ACL for the interesting site to Site traffic.
You must also add the Remote LAN B to the ACL of tunneling split for VPN clients (assuming you are using split tunneling).
In other words, the VPN router configuration has for customers VPN should allow remote control B LAN in the traffic that is allowed for the VPN clients.
You can check the above and do the following test:
1. try to connect to the remote VPN the B. LAN client
2. check the "sh cry ips his" for the connection of the VPN client and check if there is a surveillance society being built between the pool and Remote LAN B.
Federico.
-
Routing between the easy VPN clients
I have easy installation of multiple ASA5505 as VPN clients connecting to a single ASA5510 and can route packets between client subnets easy 5505. Anyone has the clues, how?
Thank you!
You must add the below to the 5510: -.
permit same-security-traffic intra-interface
HTH >
-
Need help with configuration on cisco vpn client settings 1941
Hey all,.
I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...
If anyone can help with orders?
I need the installation:
user names, authentication group etc.
Thank you!
Take a peek inside has the below examples of config - everything you need: -.
http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html
HTH >
Andrew.
-
Hi, I am building a vpn using an easy VPN server on 8xx adsl router and a remote client using xp pro.
On the server side is set up but, when the documentation says "simple vpn client" This means that the client vpn 4.6 or 4.7 or 4.8 cisco vpn client? or is a particular software?
Best regards
Edgar Quintana
In terms of support, customer of EasyVPN: customer equipment.
As routers and PIX firewalls connected as a client on the side of the head. (which will be an EasyVPN server).
The normal software clients are called VPN clients.
-
multi-site VPN with just the cisco vpn client
Hello everyone
Please I need your help.
We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.
My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?
It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.
Michael
Please note all useful posts
-
DMVPN with based remote access VPN client
Hi all
We DMVPN deployed to connect to our remote location now I want to configure the vpn remote access also with DMVPN tunnel so if somehow our DMVPN tunnel goes down we can connect to the router through vpn remote access client based around... I want experts to do the light on it is it possible or what are the technical challenges that I have to face in this regard.
Thank you
Salman Jamshed
Hello Salman,
It's 100% possible, there is no harm in having them both up on your router.
In fact, as you have said that it will provide an extra layer of redundancy if by chance the DMVPN tunnel breaks down.
That being said, you can go ahead and do it is a movement course
Julio
-
Easy VPN with the Tunnel Interface virtual IPSec dynamic
Hi all
I configured easy vpn remote on a cisco 1841 and dynamic server easy vpn with virtual tunnel interface on the server (cisco 7200, 12.4.15T14)
It works with easy vpn remote to the client mode and mode network-extesión, but it doesn't seem to work when I configure mode plus network on the client of the cpe, or when I try to have TWO inside the ez crypto interfaces. On the customer's site, I see two associations of security, but on the server PE site only security SA!
Without virtual dynamic tunnel interface, dynamic map configuration is ok... This is a limitation of the virtual tunnnel dynamic interface?
Federica
If one side is DVTI and the other uses a dynamic map, it does support only 1 SA. If the two end uses DVTI or the two end uses dynamic card then it supports several SAs.
Here is the note of documentation for your reference:
Note: Multiple inside interfaces are supported only when the Cisco Easy VPN server and the Cisco Easy VPN client have the same type of Easy VPN configuration. In other words, both must use a Legacy Easy VPN configuration, or both must use a DVTI configuration.
Here's the URL:
Hope that answers your question.
-
Easy VPN setup with interface to multiples with the same level of security
Hello
I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:
ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.
vpnlclient of configuration above:
vpnclient Server x.x.x.x where x.x.x.x
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
vpnclient username usr_ezvpn_tunnelspec password *.
vpnclient enableinterfaces:
interface Vlan200
nameif outside1
security-level 0
IP x.x.x.x 255.255.255.252
!
interface Vlan300
nameif outside2
security-level 1
IP x.x.x.x 255.255.255.128
!monitor the SLA to the routing:
monitor SLA 100
type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
NUM-package of 5
frequency 30
monitor als 100 calendar life never start-time now
ALS 200 monitor
type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
NUM-package of 5
frequency 30
Annex monitor SLA 200 life never start-time now
ALS 300 monitor
type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
NUM-package of 5
frequency 30
Annex monitor SLA 300 life never start-time now
ALS 400 monitor
type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
NUM-package of 5
Timeout 3000
threshold of 3000
frequency 30
Annex monitor SLA 400 life never start-time nowFollow-up:
!
track 1 rtr 400 accessibility
!
Track 2 rtr 200 accessibility
!routes:
Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2The track works normal.
Kind regards!
Try using the command "backup interface" on the secondary ISP interface.
http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585
You need to increase the level of security to 1 for this interface.
By default, EasyVPN uses the highest level of safety inside and the lowest outside. Anything between the two must be set manually. I assume you have an interior vlan defined but not added to the posted config.
-
CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION
Hello
I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match? Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.
Please see my full configuration:
Router #sh run
Building configuration...Current configuration: 8150 bytes
!
! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
Passwords security min-length 6
no set record in buffered memory
enable secret 5 xxxxxxxxxxx
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization exec default local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
!
No ipv6 cef
IP source-route
no ip free-arps
IP cef
!
Xxxxxxxxx name server IP
IP server name yyyyyyyyy
!
Authenticated MultiLink bundle-name Panel
!parameter-map local urlfpolicy TSQ-URL-FILTER type
offshore alert
block-page message "Blocked according to policy"
parameter-card type urlf-glob FACEBOOK
model facebook.com
model *. Facebook.comparameter-card type urlf-glob YOUTUBE
mires of youtube.com
model *. YouTube.comparameter-card type urlf-glob CRICKET
model espncricinfo.com
model *. espncricinfo.comparameter-card type urlf-glob CRICKET1
webcric.com model
model *. webcric.comparameter-card type urlf-glob YAHOO
model *. Yahoo.com
model yapoparameter-card type urlf-glob PERMITTEDSITES
model *.parameter-card type urlf-glob HOTMAIL
model hotmail.com
model *. Hotmail.comCrypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-2049533683
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2049533683
revocation checking no
rsakeypair TP-self-signed-2049533683
!
Crypto pki trustpoint tti
crl revocation checking
!
Crypto pki trustpoint test_trustpoint_config_created_for_sdm
name of the object [email protected] / * /
crl revocation checking
!
!
TP-self-signed-4966226213 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332quit smoking
encryption pki certificate chain tti
for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
license udi pid CISCO1905/K9 sn xxxxxx
licence start-up module c1900 technology-package datak9
username privilege 15 password 0 xxxxx xxxxxxx
!
redundancy
!
!
!
!
!
type of class-card inspect entire tsq-inspection-traffic game
dns protocol game
ftp protocol game
https protocol game
match icmp Protocol
match the imap Protocol
pop3 Protocol game
netshow Protocol game
Protocol shell game
match Protocol realmedia
match rtsp Protocol
smtp Protocol game
sql-net Protocol game
streamworks Protocol game
tftp Protocol game
vdolive Protocol game
tcp protocol match
udp Protocol game
match Protocol l2tp
class-card type match - all BLOCKEDSITES urlfilter
Server-domain urlf-glob FACEBOOK game
Server-domain urlf-glob YOUTUBE game
CRICKET urlf-glob-domain of the server match
game server-domain urlf-glob CRICKET1
game server-domain urlf-glob HOTMAIL
class-map type urlfilter match - all PERMITTEDSITES
Server-domain urlf-glob PERMITTEDSITES match
inspect the class-map match tsq-insp-traffic type
corresponds to the class-map tsq-inspection-traffic
type of class-card inspect correspondence tsq-http
http protocol game
type of class-card inspect all match tsq-icmp
match icmp Protocol
tcp protocol match
udp Protocol game
type of class-card inspect correspondence tsq-invalid-src
game group-access 100
type of class-card inspect correspondence tsq-icmp-access
corresponds to the class-map tsq-icmp
!
!
type of policy-card inspect urlfilter TSQBLOCKEDSITES
class type urlfilter BLOCKEDSITES
Journal
reset
class type urlfilter PERMITTEDSITES
allow
Journal
type of policy-card inspect SELF - AUX-OUT-policy
class type inspect tsq-icmp-access
inspect
class class by default
Pass
policy-card type check IN and OUT - POLICIES
class type inspect tsq-invalid-src
Drop newspaper
class type inspect tsq-http
inspect
service-policy urlfilter TSQBLOCKEDSITES
class type inspect tsq-insp-traffic
inspect
class class by default
drop
policy-card type check OUT IN-POLICY
class class by default
drop
!
area inside security
security of the OUTSIDE area
source of security OUT-OF-IN zone-pair outside the destination inside
type of service-strategy check OUT IN-POLICY
zone-pair IN-to-OUT DOMESTIC destination outside source security
type of service-strategy inspect IN and OUT - POLICIES
security of the FREE-to-OUT source destination free outdoors pair box
type of service-strategy inspect SELF - AUX-OUT-policy
!
Crypto ctcp port 10000
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 2
Group 2
!
ISAKMP crypto client configuration group vpntunnel
XXXXXXX key
pool SDM_POOL_1
include-local-lan
10 Max-users
ISAKMP crypto ciscocp-ike-profile-1 profile
vpntunnel group identity match
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
game of transformation-TRANSFORMATION TSQ
set of isakmp - profile ciscocp-ike-profile-1
!
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
!
interface GigabitEthernet0/0
Description LAN INTERFACE-FW-INSIDE
IP 172.17.0.71 255.255.0.0
IP nat inside
IP virtual-reassembly in
security of the inside members area
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
Description WAN-INTERNET-INTERNET-FW-OUTSIDE
IP address xxxxxx yyyyyyy
NAT outside IP
IP virtual-reassembly in
security of the OUTSIDE member area
automatic duplex
automatic speed
!
interface Serial0/0/0
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
no fair queue
2000000 clock frequency
!
type of interface virtual-Template1 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP nat inside source list 1 interface GigabitEthernet0/1 overload
IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
IP route 192.168.1.0 255.255.255.0 172.17.0.6
IP route 192.168.4.0 255.255.255.0 172.17.0.6
!
access-list 1 permit 172.17.0.0 0.0.255.255
access-list 100 permit ip 255.255.255.255 host everything
access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
access-list 100 permit ip yyyyyy yyyyyy everything
!
!
!
!
!
!
!
!
control plan
!
!
!
Line con 0
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
transport input ssh rlogin
!
Scheduler allocate 20000 1000
endA few things to change:
(1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.
(2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:
access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255
access-list 120 allow ip 172.17.0.0 0.0.255.255 everything
overload of IP nat inside source list 120 interface GigabitEthernet0/1
No inside source list 1 interface GigabitEthernet0/1 ip nat overload
(3) OUT POLICY need to include VPN traffic:
access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255
type of class-card inspect correspondence vpn-access
game group-access 121
policy-card type check OUT IN-POLICY
vpn-access class
inspect
-
Easy VPN with IPSec VPN L2L (Site - to - Site) in the same ASA 5505
Hi Experts,
We have an ASA 5505 in our environment, and currently two IPSec VPN L2L tunnels are established. But we intend to connect with VPN (Network Extension Mode) easy to another site as a customer. Is it possible to configure easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels? If not possible is there any work around?
Here's the warning we get then tried to configure the easy VPN Client.
NOCMEFW1 (config) # vpnclient enable
* Delete "nat (inside) 0 S2S - VPN"
* Detach crypto card attached to the outside interface
* Remove the tunnel groups defined by the user
* Remove the manual configuration of ISA policies
CONFLICT of CONFIG: Configuration that would prevent the Cisco Easy VPN Remo success
you
operation was detected and listed above. Please solve the
above a configuration and re - activate.
Thanks and greetings
ANUP sisi
"Dynamic crypto map must be installed on the server device.
Yes, dynamic crypto is configured on the EasyVPN server.
Thank you
-
RV120 VPN with full Cisco VPN Client?
Is it possible to configure the RV120 for a VPN IPsec for use with the complete Cisco VPN client?
I tried, but it does not appear to support "Goup of authentication.
I see in the confi router I can put a PSK, but the complete VPN client seems only accecpt "Goup authentication."
I managed on the basis for the work "Fast VPN", how it works is beyond me, because he does not appear to create an adapter with an IP address or anything on the local line, and I didn't even create a VPN policy...
Or put another way, what alternative (Free) VPN clients are there to work with the RV120?
Try the following link for instructions for Cisco VPN and the SA500:
I hope this helps.
Thank you
Rick Roe
Cisco Small Business Support Center
Maybe you are looking for
-
Exporting HDMI video only, NO sound
Hello I have a Lenovo Ideapad Y510p I used for a year. I have always connected via a cable HDMI to my TV SMART Samsung 32 "and it has always worked perfectly. Yet, on a fortnight there is all of a sudden it has stopped working and I can't use the HDM
-
How can I get my camera auto run when I turn it on once it is connected to my computer, as it was
-
Computer pirate 11/4, no Firefox or Thunderbird acct after reconstruction
My computer has been hacked and I rebuilt the OS Win to the original. My wereunknown of Firefox and Mozilla's Thunderbird accounts when I try to log in. How to recover-reinstalled Firefox and everything is OK.
-
I tried to copy a *. DAT file from a CD on my HARD drive. During the last 5 seconds, I always get the following error message: Error 0x80070057L the parameter is incorrect I am able to open the file, but can not copy. I tried on my laptop (Vista SP1)
-
network drivers for hp compaq elite 8100 missing
network drivers for hp compaq elite 8100 missing network controllerPCI\VEN_1814 & DEV_0301 & SUBSYS_00551737 & REV_00PCI\VEN_1814 & DEV_0301 & SUBSYS_00551737PCI\VEN_1814 & DEV_0301 & CC_028000PCI\VEN_1814 & DEV_0301 & CC_0280 PCI serial portPCI\VEN_