Similar Questions

• Oscilloscope NI ELVIS VI and VI Analyzer download omen?

  I'm looking to download NI ELVIS VI and VI of the bode Analyzer oscilloscope.   Where can I find the link to download these is?

  abestucky,

  If you install NI ELVISmx to link the two following screws you need to see now appear it in LabVIEW because they are included in ELVISmx.

  http://www.NI.com/download/NI-ELVISmx-14.0/4801/en/

  Kind regards

  CyanRyan

• How to use the kit sensor Bioinstrumentation Vernier with NI ELVIS II and LABview on a CPU?

  So I have the NI ELVIS II + and a box full of Bioinstrumentation sensor, including Kit sensors: Analog Proto board connector (s), pressure sensor, hand dynamometer, hand grip monitor heart rate, EKG sensors, Surface temperature probe, among others.

  I can't seem to get all the sensor data to my PC that I use, I'm not too familiar with electrical circuits but I followed the manual directions for the specific sensor but it seems as if it doesn't have a difference. I'm with copper son crochet and so that they know the places appropriate (according to the manual) but nothing.

  Am I missing something? I have also the is open regardless of the specific LABview laboratory (Surface Temp lab for example), but when I press run it is as the sensors are not recognized or even be recognized. The sensors are plugged into the connectors on the analog Proto Board also. What I am doing wrong, and how can I get these sensors to work?

  Any help will be greatly appreciated.

  From what I see, it looks like a typing mistake in the manual.

  Try to connect GND AI0 - and NOT ALWAYS.

  It should look like this.

  Connect the following pins for wire connector:

  1. AI0 + SIG1 analog connector Proto Board

  2. + 5V power supply DC to 5V analog Proto card connector

  3. Power supply to the GROUND to GND of the analog Proto board connector

  4. AI0 - GND of the analog connector Proto Board

• Liquid level, NI ELVIS II + and Labview

  Hello

  I am currently using a Liquid level detector, what I can say, is that it has two States, the float down = closed Contact; More float = open Contact. I wonder how do I plug the map of elvis and view both States on labview.

  Sensor in question

  http://www.Farnell.com/datasheets/91076.PDF

  Hey Foster,

  Given that production should be just be 2 States; Contact close or open contact, I believe you can connect the sensor to Elvis Conseil via digital port.

  But you first need to check what is the voltage generated when floating down and floating above that port digital just recognize the (off) LOW and HIGH (States) when it is within the range of 0V - 0.8V and 2.2V - 5 v respectively.

  Kind regards

  Laila

• How to write a program to integrate the ELVIS, LV and Excel

  Hi.I am new to LabView.

  I have to write a program to integrate between Elvis and the BT. This program is designed for first year students. Each student will create a test file in labview that contains a vague Sin - DC offset etc. then they should use the NI ELVIS oscilloscope to see the wave and post the results on a test sheet. This test spreadsheet (which should be developed in LabView) n must be self scored so when students filled in parts of 20 c answers should be marked by the program.

  To my knowledge, I think I should use Excel with LV. I also use ELVIS as a DAQ hardware but I don't know how to get started and how to use Excel, how to do a car also marked system in labview.

  Any help really appreciated.

  Hi en99,

  You should look at some of the training material online for more help to start, for example:

  http://zone.ni.com/devzone/cda/tut/p/id/7466 - good start guide for students.

  http://digital.ni.com/manuals.nsf/websearch/348FFE6BA9C9771A8625748E004B5555 - getting started with ELVIS

  http://decibel.ni.com/content/docs/DOC-7332 - example to place data in a spreadsheet

  If you search on www.ni.com for "getting started" then the product there are a lot of tutorials and useful guides.

  Let me know if you have more specific questions about LabVIEW.

  Kind regards

• Use NI ELVIS II Oscilloscope and Agilent Oscilloscope at the same time

  Hello

  I designed a circuit in the 3D NI ELVIS of Multisim view and I want to use the oscilloscope NI ELVIS II and Algilent oscilloscope show students how to work with the two oscilloscope but the problem is when I use both of them not of them works. Judgment of NI ELVIS II Oscilloscope running and the other a desnt show nothing but as soon as I delete the Agilent one OR ELVIS II Oscilloscope starts showing traces. I would like to know is possible to implement both at the same time

  On my computer the two instruments work, but very slow

  Here's a tip: disable ELVISmx instruments that you do not use (each active instrument consumes resources systems):

  • Stop the simulation.
  • Go in simulate > parameters of Simulation NI ELVIS.
  • Uncheck the instruments that you do not use.
  • Click OK.

  When an ELVISmx instrument is disabled, a small red 'X' appears next to the upper right of the icon of the instrument on the schema.

  Let me know how it works.

• Elvis II + 64 bit driver will not download

  I have a Council Elvis II + and tried to install the drivers on your laptop Thinkpad Windows 7 64-bit. I already have 32-bit labview installed, but the jury is not find the drivers by itself and when I try to select the drivers for her to use, he accepts it or work.

  I am very confused as to the cause. Is it possible for me to get a specifically 64-bit driver download?

  A mistake, that I had was that when I downloaded the drivers, he said that it was incompatible with the 32-bit driver.

  Hi SamuelDelattre,

  I do not know what link you are using however the link below is fully supported on a 64-bit Windows 7 with 32-bit LabVIEW. You can post a screenshot of the error you get? It might be useful to uninstall all the drivers ELVIS you currently one do a fresh install.

  http://www.NI.com/download/NI-ELVISmx-14.0/4801/en/

  -----------------

  Aaron F.

  National Instruments

  Engineering applications

• Problem with launichnig of used VI NI ELVIS

  Hello, I have a hard time with the launch of the virtual instruments using NI ELVIS - problem in that the program don't miss to find "NI ELVIS DIO - close.vi", "NI ELVIS DIO - write.vi", "NI ELVIS - initialize.vi" s ' Please tell - where can I get listed VI? And the 2nd problem is that in the instruments OR ELVIS (DMM for example) - in the "Peripheral" field only empty string is available. So with that, the measuring instruments is unavaileble. How can I fix it fails and specified in this field ELVIS I?

  Please pay attention to my sentence, Margaret.

  1. I use NEITHER ELVIS I have couple with car NI DAQ 6251

  2. I use the NI ELVIS v4.10 with NI DAQ software v8.9

  3. the rear switch is turn on and power light lights ELVIS brilliantly.

  So, I use NI ELVIS to ELVIS II software, but I suggest that this software is also suitable for NEITHER ELVIS I. And I don't see the difference between a device specifeing name in the menu software configire for NI ELVIS I and select the device in the "device" field in the menu of the instrument. Is this good idea to install a software for NI ELVIS I (old version)?

  Also, when I use NI DAQ in LabVIEW as a simple virtual instrument some NI DAQ and NI ELVIS works properly, and problems only appear when I try to use Software v4.10 NI ELVIS instruments...

  And also - how or where I can "NI ELVIS DIO - close.vi", "NI ELVIS DIO - write.vi", "NI ELVIS - initialize.vi" for LabVIEW?

• Running the latest Labview 2010 on new computers (Windows 7) but who have the older/more older material NI ELVIS

  We are running the latest Labview 2010 on new computers (Windows 7) but have more older/more old material NI ELVIS (NI ELVIS I?).

  LabVIEW works very well and the device drivers are installed.

  What NI ELVIS software move us?

  The latest version indicates that it is for ELVIS II and III hardware.

  Thank you

  Hi Tom,

  I'm sorry, I read your first post completely backward.  It's the pilot , you should try.  Sorry for the confusion!

  Kind regards

• Oscilloscope ELVIS II +.

  Hi all:

  I just got a unit ELVIS II + and start building some basic circuits.

  Does anyone know if the oscilloscope has a mathematical function? I need to

  subtract two signals. No matter how much help this will be appreciated. Thank you

  Jose Ramos

  You can add using the regular 'Add' primitive VI.

• Inputs voltage DAQ affecting each other and the camera, they save you of

  Hello world!

  I use ELVIS II + and LabVIEW 2012 to register a device with a resistive sensor voltage (voltage see with ELVIS II.jpg for VI). The device (device + ELVIS II Schematic.jpg) measure the voltage across the resistive sensor and is controlled by a msp430. If the msp430 believes the change of voltage of the probe is above the threshold, a light is on. There is a motor function on the device and the LED is normally not on when the engine is turned on. I found that registration with the acquisition of data affects the behavior of the device. The reasons daq hardware and devices are connected. During data acquisition does NOT record, gross and analog sensor in tensions are constant (and the LED off) while the engine is on (Figures.doc; (A). when data acquisition IS recording, the engine power seems to distort analog in / raw voltage of the sensor causing the LED lights up (Figures.doc; (B).

  The trials that did not issue (led on while engine):

  1. registering with new ELVIS II + DAQ

  2 separate inputs raw and engine sensor on data acquisition

  The tests which fixed the problem (any engine LED is off):

  1 grounding gross and/or motor sensor

  2 separate channels of raw and engine sensor in the wizard DAQ (Figures.doc; C: shows engine and raw sensor separated by A_VCC. Figures.doc; D: where engine and gross sensor are side by side). I don't know why the order of the channels in the DAQ assistant would affect the behavior of the sensor signal.

  Any advice on this problem and ways to troubleshoot/potential long-term solutions would be greatly appreciated!

  Thank you!

  If your device has no acquisition of simulteanous, then each channel is multiplexed in the ADC. It has a capacity of entry inside your device, which gives it a 'memory '. If the voltage stored in the capacitor is not unloaded a scan before the next scan starts, then the second scan will "remember" is the result of the first analysis, give you really weird problems. More source impedance on the canal e e greater probability that the signal from the previous 'remembered '. That's why the order of the questions, the higher source impedance going first.

• Error-50303 occurred at ELVISmx_DAQmx create channel %2528AI-Resistance%2529.vi%253A1

  Hello

  I used the myDaq in my electronic class earlier today and the suspect, I have damaged the myDaq. I had an external power supply connected to my circuit on a Protoboard - the circuit was not directly related to +/-bus on the protoboard, but the Council itself was hung in the myDaq.

  I noticed this caveat statement myDaq Manual:

  Power supplies
  Caveat! Do not mix the power nor myDAQ with power of external power sources.
  When you use an external power supply, remove all connections to the power supply terminals on
  NEITHER myDAQ.

  Since then, I get the following error message when I try to take my multimeter (NI Elvismx) readings:

  Error-50303 occurred at ELVISmx_DAQmx create channel %2528AI-Resistance%2529.vi%253A1

   

  This message means that I damaged the myDaq? Could I have generated too much current with voltage circuit / applied and brought to save in the myDaq? If so, it would damage the myDaq or are there internal safeguards in order to protect the device (i.e. recognizing when internal resistance reduction) and trigger an error code (i.e. could reset you HAVE resistance)?

  I am new in the field of electronics, so please forgive me for any obvious incorrect statement above!

  Also, I went then to download the troubleshooter of myDaq - I managed to unpack the file, but it would not be completed installation (i.e. the 'next' button is grayed out on the summary screen, the only options to the choices were 'save' and 'Cancel').

  Thanks in advance for any guidance/direction you can give me!

  Sincerely,

  Melissa

  Found a miracle solution!

  Under the tools NI MAX button, there is an option to select "reset Configuration data".

  After selecting this, he reset the Configurations OR and restarted my computer. I noticed that when I reopened NI MAX, I had more options to choose when I click on the myDaq device (i.e. before I could only choose 'Save' and 'Refresh'... now I have more options including a reset, self-test function, test panels, etc.).

  I was able to use my features NI Elvis DMM and no longer see the error message (just did a simple test with a resistance).

  See you soon!

  -Melissa

• generation of functions to create channels of AO

  I'm trying out a sinusoidal signal through a USB-6211 using this task Create Channel. I can't find a single example of using this function once the task has been created. All the 17 examples provided by OR use the adjustment of the tension of the AO create and must use an external function generator. Examples exist on how to use this thing? List of specifications of USB - 6211 BTW ' AO waveform modes:

  "Non-periodic waveform.

  "Periodic regeneration mode waveform of FIFO aboard"

  'Regeneration of periodic signals of buffer host, including the dynamic update'

  I don't know what the previous alternatives that seem to indicate that it is capable of producing waveforms, unlike other queries that came during my search for previous question.

  Hi walter donovan,.

  Only two devices support .vi DAQmx Create Channel (AO-FuncGen): NI ELVIS II and NI ELVIS II +, which have a function dedicated to the hardware level generator. You cannot use the channel type of the generation of AO functions with any other device. Sorry for the confusion.

  Brad

• Do not understand RMS voltage

  Hello

  I have to write a measurement software that uses a NOR-DAQ 6071E. C++ is used as programming language and the new DAQmx interface is used and seems very well at the moment.

  Now, I have a few Questions about the two functions

  DAQmxCreateAIVoltageChan

  DAQmxCreateAIVoltageRMSChan

  The first give me the unmodified sampled values?

  The second makes some calculation on each sample?

  I need to create the average arithmetic and the RMS of the samples. These features help me with that. Or do I have to do the calculations on my own?

  I know I have to do the calculations on mine, which is not a problem.

  Would be great for some advise

  BR

  Hans-Jürgen Lange

  Hi Hans-Jürgen,

  The DAQmxCreateAIVoltageRMSChan() function is only supported for the integrated DMM to the NI ELVIS II and NI ELVIS II +. For the OR 6071E, you need to use DAQmxCreateAIVoltageChan() and do the calculations yourself.

  Brad

• NI Elvis and Multisim interactive without labview

  If a circuit is implemented and tested with the help of Elvis, the results of an output displayed in Multisim and Labview?  If I want to change my Multisim simulation to match the output of the circuit set up as Elvis, is possible in real time?      I know that TINA can do with their hardware/software.     Thank you

  jweaver-

  You can display the measurements in Multisim and LabVIEW.  With NI ELVIS, you can use 12 instruments of autonomous software by installing the driver (FGEN, Noculars, DMM, ect).  The instruments are built using LabVIEW.  You can access these same instruments in Multisim environment and compare the Multisim circuit simulation commensurate with live material in real time.  I included a tutorial describing how to do it using equipment OR myDAQ.  The steps are the same for NI ELVIS.

  If you want to create a custom beyond the 12 instruments application, you can program the instruments in the LabVIEW programming environment.

  " Use myDAQ with NI Multisim Circuit Design software