Energy via SNMP

I have been asked to collect data periodically from switches using SNMP.
The "show power" command gives me that information on the command line (see below), but I am unable to find this data via SNMP. Is this data available via SNMP? Does something specific have to be enabled to allow it? The switch in question is running the following software if it helps.
Cisco IOS Software, Catalyst 4500 L3 Switch Software  (cat4500e-ENTSERVICESK9-M), Version 12.2(53)SG2
show power

Power                                             Fan      Inline

Supply  Model No          Type       Status       Sensor   Status

------  ----------------  ---------  -----------  -------  -------

PS1     PWR-C45-4200ACV   AC 4200W   good         good     good

PS1-1                         220V   good

PS1-2                         220V   good

PS2     PWR-C45-4200ACV   AC 4200W   good         good     good

PS2-1                         220V   good

PS2-2                         220V   good

Power supplies needed by system    : 1

Power supplies currently available : 2
Power Summary                      Maximum

(in Watts)              Used     Available

----------------------   ----     ---------

System Power (12V)       1162        1360

Inline Power (-50V)      1007        2998

Backplane Power (3.3V)     40          40

----------------------   ----     ---------

Total                    2209 (not to exceed Total Maximum Available = 4200)
Power Measurement    Inline Power (-50V)

(in Watts)             (+/- 50Watts)

Hello
Try with below mib for consumption OID is available as long as the cdp is enabled.
Maybe one of these MIBs displays the info you are looking for.
cefcFRUPowerSupplyGroupTable.1.1
cefcFRUPowerSupplyGroupTable.1.2
cefcFRUPowerSupplyGroupTable.1.3
cefcFRUPowerSupplyGroupTable.1.4
cefcFRUPowerSupplyGroupTable.1.5
cefcFRUPowerStatusTable.1.1
cefcFRUPowerStatusTable.1.2
cefcFRUPowerStatusTable.1.3
cefcMaxDefaultInLinePower
cefcFRUPowerSupplyValueTable.1.1
cefcFRUPowerSupplyValueTable.1.2
cefcFRUPowerSupplyValueTable.1.3
cefcFRUPowerSupplyValueTable.1.4
ciscoEntityFRUControlMIB.1.1.5
Hope to help!
Ganesh.H
Don't forget to note the useful message
 
         
 
         
 more
 
		 
 Tags: Cisco Security
 
         
         
 
          
Similar Questions
 
          
 
            
           
 
		     
Access to the use of memory and processing power charge connect 6224 via SNMP.
 
			 
Hi support them
Is it possible to access the use of memory and processing power charge connect 6224 via SNMP? If possible, should the mib I use?
Thanks in advance
Rogerio
			 
When looking through the available MIB found in the zip file for download of the latest firmware.  I see that the MIB fastpathswitching mentions 'agentSwitchCpuProcessGroup '.
MIB fastpathlogging has 'agentLogInMemoryConfigGroup '.
There is no reference document material about what offer different MIB.
I hope this helps.
		   
 
            
           
 
		     
Access to the table of dynamic addresses via SNMP
 
			 
Hello
I am trying to access the table of dynamic addresses via SNMP, with a PowerConnect 6248 switch. I tried to follow the instructions [1], as other parts of the BRIDGE-MIB are ok on this switch.
When snmpwalk'ing BRIDGE - MIB:dot1dTpFdbEntry, I have nothing, while, on the switch web interface there are entries in the table.
Any idea?
[1] http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a00801c9199.shtml
			 
		   
 
            
           
 
		     
802. 1 X port management via SNMP
 
			 
Hello
Could someone tell me how to disable 802. 1 X for the specific port via snmp command?
That is to say, I can do it in the cli "not auto port of authentication control." But I need to do it in the form of "script" more.
as we can disable/enable the port like this:
The VALUE ON (1) switch (2) by interface ID

    snmpset-v2c private switch.host.name - c 1.3.6.1.2.1.2.2.1.7.10102 I 2
I tried to browse the CISCO-PAE-MIB and has not found the solution...
Links or ideas?
Thank you.
Catalyst 2960 S PS Series...
			 
Hello
don't know if this will work, but you can try to set to dot1xAuthAuthControlledPortControl by default (3:forceAuthorized):
 snmpset -v2c -c private switch.host.name 1.0.8802.1.1.1.1.2.1.1.6. i 3

(Note that the Cisco Object Navigator showes an incorrect OID).
HTH
Rolf
		   
 
            
           
 
		     
SGE2010 how to trigger backups via SNMP?
 
			 
Hello
I've tried, so unsucessfully, to trigger backups on our switches SGE201 TFTP server. I have backups testesd TFTP through the web interface, and who does not. I need SNMP as I need a method for trgiger scriptable backups on a regular basis. I run the query SNMP from a RedHat Linux server. So far, I have the following query worked, but it is a failure:
snmpset - v - 1 c COMMUNITY SWITCH. MGMT. JPM ADDRESS 1.3.6.1.4.1.9.6.1.101.87.2.1.7 I have 2 1.3.6.1.4.1.9.6.1.101.87.2.1.8 I have 3 1.3.6.1.4.1.9.6.1.101.87.2.1.9 has TFTP.SERVER.IP.ADDRESS 1.3.6.1.4.1.9.6.1.101.87.2.1.11 s 1.3.6.1.4.1.9.6.1.101.87.2.1.17 FILE name I have 4
The error I get is generic, and the same query failed on several switches operating the 3.0.0.18 software. The switch is set with the community having full access from the IP address of the SNMP-admin server.
If someone here was able to run SNMP triggers backups and would be ready to post their query and/or software that would be greatly appreciated. Any other suggestions, comments or tips are also welcome. Thank you for your time.
			 
Jeff,
The procedure to download or update the config via SNMP is as follows:
(1) download the MIB files that we officially freed from cisco.com
http://www.Cisco.com/Cisco/software/release.html?mdfid=282414069&flowid=3650&softwareid=283415684&release=3.0.0&relind=available&rellifecycle=&RelType=latest
(2) compile the MIB on MIB browser in format for example MG-SOFT, Kortright. Make sure that there is no error in compilation.
(3) configure SNMPv2 or SNMPv3 accordingly on switch SGE2010
(4) search for the CISCOSBCopy.mib file.
The OID is SNMPv2 - SMI:enterprises (1.3.6.1.4.1) .cisco (9) .otherEnterpise (6) .ciscosb (1) .odm1 (101). CISCOSBCopy (87)
With the help of rlCopyTable (2), create a new entry on this particular table:
a. rlCopyRowStatus: 4 (createAndgo)
b. rlCopySourceLocation: 1 (local)
c. rlCopySourceIpAddress: 0.0.0.0
d. rlCopySourceUnitNumber: 1
e. rlCopySourceFileName: (empty)
f. rlCopySourceFileType: 3 (config startup), 2 is for execution of config
g. rlCopyDestinationLocation: 3 (tftp)
h. rlCopyDestinationIpAddress: 192.168.10.22 (ip address of the tftp server)
i. rlCopyDestinationUnitNumber: 1
j. rlCopyDestinationFileName: 0 x 61: 62:63 (in hexadecimal, abc)
By doing this, it should be able to backup startup config devices unit to remove the tftp server.
		   
 
            
           
 
		     
Monitoring ESXi 4 via SNMP
 
			 
We have a network and a monitoring program device that now takes in charge "ESX".  However, we would like to try and see if we can use it to monitor the ESXi.  We currently have vSphere Enterprise with ESXi and vCenter installed.
Is there a way taken in charge to monitor the ESXi hosts and customers using SNMP?  We point the SNMP monitor at each host, or just for the vCenter Server?  If possible, how to define the community string, etc.
Thank you!
			 
Hi Travis,
Try this thread:
http://communities.VMware.com/thread/170567
		   
 
            
           
 
		     
VCO get entry to vcops via snmp
 
			 
You ask someone succesffuly was able to enter data into vcops vco.
I followed this guide. vCenter integration of Operations with vCenter Orchestrator in 5 minutes or less | VMware vCenter Orchestrator Blog - VMwar...
was really great.
However, in the journal of politics, I see mainly
13:06:17.342 2014-08-15] [I]
> > > Trap for oid 1.3.6.1.4.1.6876.4.5.1.0.13 jumped!
This means that the script in politics does not know this oid. .
After further research it seems you have to set manually in the oid name match and must also be in the configuration of vcop attributes (self-titled) If you can run
workflow.
is that correct, has anyone used previously?
			 
OK, I solved the problem... fixed code of vmware. .. I don't know there is a cleaner for it... way just not a lot of time to devote to this. so quick fixie
var trapOid = data.get ("oid");
from here on out to the bottom we are switching.
System.log ("it is before regex \n");
System.log ("TrapOid:" + trapOid + "\n");
var temptrapOid = trapOid;
var RES = temptrapOid.split (".", 9);
var trapOid = res [0] + "." + [1] + '.' + res [2] + '.' + res [3] + '.' + res [4] + '.' + res [5] + '.' + res [6] + '.' + res [7] + '.' + res [8];
System.log ("it's after regex \n");
System.log ("TrapOid:" + trapOid + "\n");
up to far.
		   
 
            
           
 
		     
PowerConnect 5548P Fatal Error - SNMP-F-BADTDOMAIN
 
			 
I have a stacked with 6 units of 5548P switch and I followed their status and basic via SNMP using Spiceworks and PRTG info.  Yesterday we had a weird breakdown where all the ports on the unit 4 are off (indicator HDMI and StackID remained upward) affecting traffic and POE devices connected to this unit.
After the restart of unit 4, things are back to normal. Then, check the logs of the system, I found the following message is displayed. Has anyone seen this error before?
% SYSARE STCK-A-UNITMSG: UNIT 1 ID, Msg: % SNMP-F-BADTDOMAIN: invalid or not supported TDomain received - function SNMPNotifyG_TDomainAndTAddress2UdpAddress 2 * FATAL ERROR * task Reporting: NCCD. Software version: 4.0.1.11 (October 16, 2011 time 18:10:50) 0x19f5c4 0x19c228 0x6aa9f4 0x49ba70 0x4a0f3c 0x4a10f8 0x484ba4 0x5dc3d4 0x5c6d44 0x5c6fc4 0x5c7028 0x5c7204 0x5c7258 0x5c79a4 0x5c7a70 0x5c7c20 0x5bfd78 0x5bff68 0x6856ac 0x68713c 0x4ca6dc 0x4caa9c 0x1548d0 * END OF FATAL ERROR *.
Thank you
			 
I did some research about this error message and could not find a lot of information. The version of the software on the switch seems to be a very old version. The most recent firmware includes many improvements to SNMP and corrections where specific SNMP events would result in a switch to crash. A time to update the firmware of planning is the first step, I suggest you.
http://Dell.to/1OQ6vi5
Once updated, then watching to see if this problem persists.
		   
 
            
           
 
		     
R420 SNMP memory status
 
			 
Hello
I try to get the status of memory via snmp on R420, idrac7, bios version 1.5.2 firmware 1.57.57. I am able to get other statutes as cpu but memory. IDRAC-MIB that i've got has supported the following responsible OID:
memoryDeviceStatus 1.3.6.1.4.1.674.10892.5.4.1100.50.1.5
but I can't do:
$ snmpwalk - v 2 c-c 192.168.1.30 public 1.3.6.1.4.1.674.10892.5.4.1100.50.1.5
ISO.3.6.1.4.1.674.10892.5.4.1100.50.1.5 = No. Such Instance already exists for this OID
the same goes for systemStateMemoryDeviceStateDetails - 1.3.6.1.4.1.674.10892.5.4.200.10.1.26
and all the other related memory OID. I can see memory in FRU data but not what I would use.
Any help or ideas would be greatly appreciated.
Thank you.
			 
Ok. It seems that finally sorted. OID is not accessible when memory-> system memory test is disabled. Which is the default (!). Obviously, it is not editable without rebooting is a trap for production approx.
I don't know why associated as only requested docu "Indicates if tests memory BIOS software-based system are carried out during the POST.". " »
Thank you.
		   
 
            
           
 
		     
SG - 500 - OID SNMP to lower the CPU load?
 
			 
Hello
I have several SG500 (autonomous and stacked). How can I get the CPU via SNMP load? Who knows the correct SNMP OID to lower the CPU load?
In the MIB that are provided for download one was not able to find the correct OID.
			 
Hello
There are three OID for the CPU usage:




CPU utilization for 5 seconds


. 1.3.6.1.4.1.9.6.1.101.1.7.0




CPU utilization for 1 minutes


. 1.3.6.1.4.1.9.6.1.101.1.8.0




CPU utilization for 5 minutes


. 1.3.6.1.4.1.9.6.1.101.1.9.0




This came a note of junk, I got in an email, so I don't know exactly where this information is originally.
Let me know if it works for you,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
		   
 
            
           
 
		     
Cisco Nexus 3548/3524 SNMP Interface traffic problem
 
			 
Hi all!
I would like to share with you the problem I've encountered SNMP interface respect tracking on the Cisco Nexus 3500 of traffic devices.
We is transferring our network infrastructure in the Nexus and we encountered a problem with the interface bitrate of tracking traffic on Nexus 3548: deltas SNMP counter ifHCInOctets and ifHCOutOctets show no valid data.
We have investigated this issue and figured he could be linked with the refresh rate of the meter.
I measured, by snmpwalk, the time between simple increments the counter ifHCInOctets to Interface VLAN and it apears to about 140seconds. But for physical interfaces (Eth), the interval of interface SNMP counters are 15 seconds and with sampling frequency of the 1960s for the queries we can still observe the problems on graphs (see attached screnshot).
We get the same results when testing the question on various physical devices (3548 Nexus) on versions of different software - including the last being.

snmpscreenshotvlanint.jpg

        
    

And for Ethernet interfaces (same NMS - ZABBIX-config):

snmpscreenshotphint.jpg

        
    

We tested a wide Huawei s6700 switches and the range of Cisco IOS devices and there is no such problems.
The main problem is that we cannot monitor our crucial nexus, via SNMP devices (as you can see from the attached chart).  Results are the same when configure us Cacti or Zabbix to monitor Nexus devices.
The results of this monitoring not having meritorical value or use.
We are working on this case with Cisco TAC, and they manage to reproduce the problem in their LAB environment. But for now, they cannot provide any solution and they claim that this isn't a bug. If we get any final statement for this case, I'll post here for your information.
I'll be more than happy if you can post ideas that help me solve the problem described.
Thank you in advance!
Michal
			 
Looks like a bug to me.  His return of erroneous data.
Maybe try asking your file be traced back to the team leader.
		   
 
            
           
 
		     
FWSM and ARP SNMP MIB
 
			 
Hello
I have two cards FWSM in two 6513 switches with active failover.
Connected to the switches are several servers connected to different interfaces of the firewall. One of them is a HPOV (openview) needs the ARP table of the FWSM to reach and explore the net together to start to monitorize the network.
My problem is that I can't get the firewall ARP table, so I can't find out more devices, I am able to SNMP them by editing the poller SNMP in the configuration file of OVO, but even network devices is displayed, it cannot achieve the work.
I stick my worm here sh.
FWSM-1 # sh ver
FWSM Firewall Version 3.2 (1)
Version 5.2 (1) F Device Manager
Updated Friday, June 7 07 20:16 by which
FWSM-1 up to 7 days, 13 hours
1 year 94 days upwards failover cluster
Material:-WS-SVC-FWM-1, 1024 MB RAM, Pentium III 1000 MHz processor
Flash Flash STI 7.2.0 @ 0xc321, 20 MB
0: Int: do not license: irq 5
1: Int: do not license: irq 7
2: Int: do not license: irq 11
The activation key running is not set, using the default settings:
The devices allowed for this platform:
Maximum Interfaces: 256
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Security contexts: 2
GTP/GPRS: disabled
Heel of BGP: disabled
VPN peers: unlimited
Serial number: SAD101804FV
Activation key running: 0x00000000 0x00000000 0x00000000 0x00000000
Configuration changed from enable_1 to 13:59:35.590 THIS Monday, November 3, 2008
I think that version 3.2 can not recover the MIB for ARP, and I found this version 4.01 only. But I was unable to find any kind of upgrade notes here, and we have the control of server farms proyect sttoped for this problem.
Any who had this problem?
How did solve you this?
Thank you!
			 
Angel,
You're right, '(IP - MIB) ARP table entries' MIB was introduced in 4.0 (1) and you have to upgrade to 4.0 code to get to the ARP Table via SNMP MIB.
And here is the document that contains information on the FWSM upgrade.
http://www.Cisco.com/en/us/docs/security/FWSM/fwsm40/configuration/guide/swcnfg_f.html#wp1052902
Kind regards
Arul
* Rate pls if it helps *.
		   
 
            
           
 
		     
Adding accounts on ACS using SNMP
 
			 
Hi people,
I use ACS 4.2 and I was just wondering if it is possible to add user accounts by using snmpset? If so, anyone found any documentation on what needs to be done?  I have the SNMP running on it and check with the ACS using snmpget.
Thank you, S.
			 
Hi Shane,
It is unfortunately not possible. You cannot add users via SNMP.
However, you can add multiple users at once using RDBMS synchronization.
HTH
Amjad
Sent by Cisco Support technique iPad App
		   
 
            
           
 
		     
Access PIX NIC canoe internal via VPN
 
			 
Hello
We have a customer with a PIX 515 we installed and we have a private network virtual of our office to them. We communicate to all their guests behind the PIX over the good VPN configuration (telnet) and monitoring (SNMP). We want to control the PIX via snmp as well. We are unable to access the internal ip address of the NIC through the VPN. We can not ping, telnet or use SNMP to it.
The VPN works great as I said above, but is there anything else I need to do to allow access to the internal IP of NIC address?
			 
This is the normal behavior of Pix. You cannot communicate with a Pix interface unless it's the only one to receive the traffic. Therefore, you can monitor and communicate with the outside/IP of the Pix from the Web interface.
BTW... This changed in Pix v6.3 that came out yesterday. You can use the command [management-access] to manage your Pix using his IP address private through a VPN tunnel.
		   
 
            
           
 
		     
SNMP VS. Syslog
 
			 
Hello
I have the Cisco MARCH tool SIM in my environment and I currently use syslog messages for report of activities for various devices; I would like to see what I would get if I compatible SNMP on what is currently collected through syslog messaging?
Thank you
Haitham
			 
Hi Haitham,
SNMP provides limited/specific type of newspapers through traps, for example, restarting the system, BGP. ATS and so on.
For example, in the router, you can see snmp options via "snmp-Server enable traps?
http://www.Cisco.com/en/us/Tech/tk648/tk362/technologies_tech_note09186a008021de3e.shtml
Syslog will generate and send logs syslog level that allowed you to be sent to MARS. Recommended level is information so that you can collect all the information/events in a specific device. But you can always specify this level based on the criticality of the device.
SNMP and Syslog complement each other in order to provide accurate and sufficient information to be processed by MARCH. NetFlow is also an excellent source of information.
Rgds,
AK