ENVY 750-055xt CTO: hard disk capacity

Similar Questions

• 750 - 055xt CTO M0K53AV #ABA envy: HP has encountered an error when trying to analyze your product

  I use a brand new HP Envy 750-055xt CTO. Added the SSD (Samsung 850 EVO 120 G) and 16G Ram (Total of 24G (from Crucial)). The Win 7 OS has migrated to SSD and formatted the original drive for the purpose of storing files to a printer large format (new HP Latex, which will happen later this month).

  Attempted to install Windows 10 but had multiple failures with error 0x80073B92 - 0 x 20009.

  Disconnected SSD in case it was originally the above error, restored the system using created recovery DVD to state of origin (but always with 24 G of Ram).

  In trying to pilot research and updates to bios on the HP support page, I now encounter error "HP has encountered an error when trying to analyze your product" which leaves me to proceed, except to order the DVD of restoration Windows 7.

  I know I'm forgetting something in this whole procedure, but I have no idea at the moment what it could be.

  This can help with the installation:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-windows_install/Windows-10-upgrade-failed-with-0x80073b92-0x20009/15eaaeab-9ECB-4C06-bd8d-62c783d51cf6?auth=1

  HP site:

  http://h30434.www3.HP.com/T5/notebook-operating-system-and-recovery/error-while-trying-to-scan-product/TD-p/5369812

  Hope this helps

• ENVY 750 - 055xt: screw the motherboard for socket mSATA

  I have the HP ENVY 750-055xt, which uses the motherboard of Kaili.  There is a plug on the motherboard mSATA and I inserted an EVO of 850 Samsung 1 TB SSD.  Fortunately this solid state drive works and is immediately recognized by Windows 7, no other frills.  However, the motherboard doesn't have the small screws in the tiny mSATA solid drive on the motherboard.

  Anyone know the right screw size used to secure the mSATA SSD to the motherboard in Kaili?

  Hi Big_Dave,

  Thanks for your reply.  I have besides a picture of the Samsung 850 EVO mSATA SSD drive.

  

  It fits in the slot on my motherboard HP MS-7826 (Kaili) mSATA.  Please see below.

  

  The drive performs as well as my boot drive.  As it is not properly attached to the motherboard, the only thing holding is the strength of tensioning of the socket.  Ocassion the tiny jury comes off in the socket and it won't be visible in the path of startup.  Opening upward the chasis LIKE 750 and re - insert the mSATA jury will get the computer running again.  The little screw would prevent the Council of Regularisez making and the frustration of re-Foundation there.

  Elsewhere in this forum, I found mention of the screw that I'm looking.  This is the same as that used in the dwelling of minimap express PCI used for the WiFi card.  The expertise here source describes the machine screws Flathead as a M1.6 size.  I ordered a M1.6 x 3 mm of China.  I think it should work.  Some here said they used a M2.0 to head flat screws in the slot mSATA and it seemed to work for them.

  My motherboard HP isn't a slot m2.  If so, then I probably would have opted for the Samsung SSD m2, instead of the mSATA SSD drive.

  For now, I think I solved the problem with the mother screw missing for the location of nSATA.  Nevertheless, Big_Dave, thanks for responding to me here.

• Envy touchsmart 15 - new HARD disk size

  I recently ordered a Touchsmart from HP Envy 15-j005sa that has a 1 TB HARD drive. I'm looking to clone the orignial in an mSATA SSD drive so I was wondering what size is recommended.  How much space is used when it is new so using this information can buy a large enough disk size?

  Thanks in advance

  Hello

  There is that little clone options b clone the HARD disk which means that you have the mSATA SSD equal or more 1 TB (b) clone c ONLY: This means you the mSATA SSD equal or superior to c:... My suggestion: shrink C: for small size say even 60 GB or 120 GB (if you don't have a lot of programs installed) FRONT of clone and ONLY clone C: normally larger (capacity) is better because you can install more programs that him.

  Kind regards.

• HP ENVY 750-055XT: HP download win 10 for win 7

  I bought a refurb unit. He came "upgraded to win 10 64.  But there is no win 7 files to restore.  I have a new win 7 64 pro license. On the CD.   How can I install and lose 10 WIN.  I want to have anything to with win 10 in the computer.

  I have the same computer with win 7 pro 64 installed. I have raid 1 disks.  If I removed the drive in the new computer and installed one of my raid drives which would solve the problem?

  I'll have one connected to the internet and the other will have my critical files and will not have internet capability.

  @HEMI7309

  http://support.HP.com/us-en/mediaorder/HP-envy-750-desktop-PC-series/7779687/model/7805186/softwareitem/M2H64AV/STEP1

  REO

• Fusion is stopped because the virtual hard disk capacity is reached

  I run Windows XP Pro in a virtual machine with the German Fusion 3.1.1 on my MacBook 13 "with Mac OS X 10.6.2.

  When I try to start Windows the VM said: "VMware Fusion has the virtual machine is stopped, because the capacity of the hard drive (40 GB) is almost reached."

  But this Windows disk management in the first partition 'Win XP Pro' 15 GB to 30 GB are free. And on the second partition 'Install' 8 GB to 10 GB are free.

  I took the snapshot on the virtual machine and have managed hard disk cleanup. But it does not help. Fusion said I do free 1.2 MB capacity of the virtual hard disk. How can I do this, when the merger does not start?

  The opportunity to make more the virtual hard disk of 40 GB to 50 or 60 GB is blocked, I first have to delete the snapshot. But the snapshot is deleted.

  What can I make Fusion work again?

  czer27 wrote:

  When I try to start Windows the VM said: "VMware Fusion has the virtual machine is stopped, because the capacity of the hard drive (40 GB) is almost reached."

  I doubt that what you quoted is the message itself, so it would be more useful if you attach the .log files.  See information for VMware Fusion to help with that.  Howevere...

  I bet that the message is more like "VMware Fusion has suspended this virtual machine because the disk on which the virtual machine is stored is almost full. To continue, free at least MB of disk space. "and as such, you must do exactly what means the message and that is free space hard disk Macintosh not space inside the VHD.  After all, it's the Mackintosh HD stored on the Virtual Machine, isn't?

• Initial configuration of RAID HP ENVY accidentally erased, deleted hard disk?

  I was trying to see if I could find an option to change the my new laptop on AHCI SATA controller, but I should have checked more thoroughly online before trying something new in the BIOS.  It seems that these laptops are automatically in AHCI?

  My laptop had a 1 TB SSHD and a 24GB flash hard drive Cache acceleration configured in RAID 0.  With my minimal knowledge of the AHCI, RAID and IDE, I thought that the withdrawal of the RAID configuration would give me a possibility to change the hard drive in AHCI controller.  Without thinking, I "removed" the RAID volume, and I think I have completely erase my new hard drive and the operating system, including the recovery partition.

  When I start up the laptop, I get the error "boot device not found 3f0", and f11 does not work to try to get into the recovery mode.  The hard drive test always passes the two elements.  I ordered at HP USB recovery media earlier, but I don't know if there is anything else I can do?

  I don't know exactly how the acceleration of the Disk Cache, but my main question is why only SSHD would be setup in RAID 0 factory mode, and if there is a good reason, how do I put up again after the reinstallation of the OS from the USB media?

  After screwing my OS, I played in the BIOS to re - setup the RAID0, but I don't know that I've got it right.  I myself remember the size of the band was set to 128 KB, but I have no idea what was the "Capacity (MB)", or should I put it when I create new RAID?

  Any help would be appreciated.  Thank you.

  Ryan

  Hi, Popo:

  I didn't get the rush of shipped recovery media.

  When you order by regular mail, it may take up to 10 days, so unless you're bored to death, so I would just wait until your recovery media is coming tomorrow.

  Yes, you are right.  The file I gave you is a simple vanilla W8 version and there are no programs whatsoever other than that which accompanies the W8.

  The product key in the BIOS of your PC will work with this file and you get the recovery media.

  You can always want to DL this file and make a bootable DVD just as it is for future use.

  After installing W8, you get the upgrade to W8.1 against the Windows store.

  It may take a few hours to appear as a sort of update should run before updating the W8.1 appears in the Windows store.

  You won't have to look for.

  It will be displayed when you click the windows store.

  You will be able to switch to W8.1 with the regular ISO W8 file, or your installation HP factory.

• Can not read the HARD disk capacity properly after the upgrade on my Satellite A135-S2276

  I have a Satellite A135-S2276 and I recently updated my 80 gig HDD with a 320 GB HARD drive and drive C shows only 72 GB of available not the 300 - ish that it should have. I did some research and it seems that it should be there, perhaps simply not visible? Update the BIOS?

  Any suggetions?

  Thank you!

  Hello

  I think that the A135-S2276 supports SATA HDD so I doubt that the issue of the LBA48bit could be the reason.

  I found the details here on the Toshiba page we:
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/modelContent.jsp?CT=DL&OS=&category=&MOID=1596141& rpn = PSAD6U & modelFilter = A135-S2276 & SelCategorie = 3 & selFamily = 1073768663

  In your case, I would recommend formatting the disk HARD whole again.
  In addition, you should check the size of the HARD drive in the BIOS.

  Generally, if the HARD drive has been recognised in the BIOS correctly then the OS should see all 320GB too.

• Satellite A100-192: after Vista installation HARD disk capacity has decreased

  I am a user of Satellite A100-192 with 120 GB hard drive. After I installed Vista Ultimate, I saw this total capacity of my hard drive completely passed to 92, 8 GB instead of 120 GB while it was XP.

  What can be the problem? How can I reach the other capabilities of my hard drive?

  Hello

  Vista needs and used 2 partitions. The second partition is not visible and it s necessary to Vista backup and restore functions.
  Maybe you have verified that the size of the first partition (C) and didn't note the size of the second partition.

  Concerning

• envy touchsmart 15-j024sa: hard disk hardware kit

  I just got a 15-j024sa envy touchsmart, there a 126 GB ssd card but I need a disc hard material kit part No. 718432-001. If I can fit a 2.5 drive ".  Where can get a please.

  I'm in the United Kingdom.

  Hello

  Please use the following stores:

  http://PartSurfer.HP.com/search.aspx?SearchText=718432-001

  http://www.eBay.co.UK/ITM/HP-envy-15-J-Series-SATA-hard-drive-connector-w-cable-6017B0416801-/131399170824?PT=LH_DefaultDomain_0&hash=item1e98003b08

  http://www.eBay.co.UK/ITM/720545-001-6017B0416801-HP-15-J013CL-envy-15-J-hard-drive-caddy-cable-grade-A-/151187198856?PT=LH_DefaultDomain_0&hash=item2333759388

  http://www.newmodeus.com/shop/index.php?Main_Page=product_info&cPath=2_5&products_id=547

  Kind regards.

• HP Envy M7 - J078CA Touchsmart: hard disk failure Envy Touchsmart

  Hello

  To put it simply, my hard drive went south and I've never done the recovery DVDs.  Can I replace the HARD drive with a new drive, but obviously a source of reinstalling the OS need return to the default settings.  I saw another thread on the forum dealing with this same issue and explaining what to do, so I followed the steps to create a bootable USB key with the image ISO in the thread, but then realized that my model did not match the model presented in the discussion.  I wonder what is the propper iso file for my hardware (HP ENVY M7-J078CA).  I was going to add to the other thread, but thought I'd start rather cool.  If the thread is necessary I can paste a link for reference.

  Any help would be appreciated.

  Thank you

  Rick

  Hello:

  "It looks like it will install a generic Win8 or 8.1 OS, not the specific HP which has the additional hp software and drivers for the HP hardware (like the fingerprint reader, etc.) on a particular model of HP laptop.

  What I posted in my first answer is a CLEAN INSTALLER download link. It is the only link legal and available at the present time. It will work on your laptop computer to install the operating system. As I said, the drivers can be downloaded from your linked above support page.

  If you want to restore all settings with all the drivers, you must use the USB/recovery discs you must have created once you have installed the laptop first. If you don't have that, order them specific to your model of HP:
  http://support.HP.com/us-en/document/bph07143

  Contact HP:http://www8.hp.com/us/en/contact-hp/ww-contact-us.html

  The link of ISO in the thread you linked is also a link INSTALLER CLEAN, which may or may no longer be active today. I'm not sure. It is the same for all HP supplied with Windows 8 pre installed. But Microsoft withdrew the support of all these links earlier and he's not sure if the activation of these facilities would certainly be well after the installation.

  Concerning

  Visruth

• Z61p - Maximum HARD disk capacity

  Hello

  I had a Z61p with 100 GB HARD drive. I want to spend to 320 GB or 500 GB HARD drive. Do you know that my computer supports these capabilities or not?

  Kind regards

  Muharrem.

  Thanks for the quick response.

  I had thougt that maybe there is a limit of capacity by SATA controller.

  So that means I can connect any HARD SATA 2.5 inch drive without a problem?

• Newbie question: hard disk capacity

  Hello

  I have 4 x 73 GB HARD drive and when I installed VMWare he showed me only 2 drives each with a capacity of 63 GB about (I don't know the exact but close to this number). I wanted to build at least 3 to 4 VM thinking that would be enough, but after the installation, I think it shows only 63 GB and I couldn't create 1VM with a size of 40 GB for my Windows Server 2012. What Miss me? Is the other HDD 2 installed summer under parity or what? Not sure, it's been long that I played with the material side. Get at least 146 GB total even in the worst case? Help!

  Thanks in advance

  IIRC the G5 models were introduced in 2006 or 2007 and has a controller E200 or SmartArray P400. In any case, press F8 when the RAID controller is all by starting the server should get you to ORCA (Option ROM Configuration for berries) where you can set the RAID configuration. Did you only need SmartStart CD if you want for example to configure multiple logical volumes on the RAID sets, as the ORCA will create just a single logical volume once you have installed a RAID set.

  André

• HP Envy 750-197c Desktop: you can add a SSD internal flash disk to the envy of HP 750-197c Desktop

  You can add an internal SSD to the envy of HP 750 - 197c Desktop that has a 2 TB drive installed?

  DMSIceman, welcome to the forum.

  Yes, you can move the HARD disk and install an SSD.  You will need to buy at least a 128 GB SSD.  Here is the data sheet for the computer.

  The best way to install an SSD is to leave the current HARD drive as it came from the factory.  Connect the SSD drive to another SATA port on the motherboard.  Install the software of Migration data provided by the SSD manufacturer on the HARD drive.  Once installed, open it and follow the instructions carefully.  You choose the SSD as a target.  After the data is transferred from the HDD to the SSD, you can disconnect the HARD drive and start the computer.  It should start on the SSD.  Then, you can disconnect the SSD to the first SATA connector and move to another Bay HARD drive and connect it to another SATA port on the motherboard.  You can use it for storage.

  I like the SSD Samsung EVO.  Samsung offers its data Migration software to clone HARD drive.  In addition, they provide their software Wizard to optimize the performance of the SSD.  You can find all the software at the bottom of the page in the link I provided for the EVO.  The Samsung SSD were good about starting in HP computers without changing the BIOS settings.  You will need to buy an adapter to allow the reader to 2.5 "to fit into a 3.5 Bay".

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Capacity of the hard disk on the Qosmio G20-139

  I recently bought the notebook of Toshiba Qosmio g20-139, announced as having an 80 GB hard drive. Check the properties of the drive C: I think capacity is 69.8 GB. And in the properties of the device, it gives the Volume 71547 MB (I presume it's 71,547 GB).

  Does anyone can ease my mind explaining to me why I have not been 'ripped off '?

  Thanks in advance.

  Hello

  I'm not 100% sure but I think this part of the HARD disk is not partitioned and it comes preinstalled Qosmioplayer. This player doesn't need all the space, but if recording on this drive is available, I presume that this registered program is also recorded on this unpartitioned part.