error 0210: stuck key 7B

Similar Questions

• Error: 0210 stuck key 19

  Hi all.

  My Lenovo computer is dΘmarre. When I hit the Party think butten fast enough, the screen appears with four options, such as retrieve etc.. However, as soon as I'm in this screen of my laptop starts beeping and gives ERROR 0210 Stuck Key 19 press on after 9 seconds to Setup.

  The keyboard did not work at the time by pressing F1 was not possible.

  After 10 minutes my computer has suddenly started once and I could enter my password normally. However, after 1 minute everywhere ' p appeared.

  As it seems that the p is stuck, I cleaned the keyboard, but do not solve the problem.

  After that, I completely removed the keyboard and mouse. However, that was not also to solve the problem.

  Do you have an idea what to do?

  Thank you

  Arnold

  If other people are having the same problem:
  The solution (for me) seems to be disconnecting the CMOS for a night (more than 8 hours). In other words, remove the BIOS battery. If problems still occur, maybe replace the cmos battery.

• error 0210: stuck key 2B - thinkpad t61 + windows 7 32 bit

  "Whenever I turn on the system I get this error 0210: stuck key 2B. If I press the ESC key, then she starts the operating system windows 7 and also after starting, if I open any ms word document, key # gets automatically in a hurry and I could see characters # continues typing in the doc, he started only after installing the w7 in my thinkpad. Can anyone suggest me if it is a failure of keyboard or operating system issue. This is repeated even after I clean the keyboard and then turn it on again. What happens in the bios, I hear a continuous even in the bios beep as if some button get all the time. So please let me know what I need to change the keyboard everything or just reconnect it or something else is under way. Please help me, I wonder why this problem began immediately after I installed Windows 7. If its an OS problem, am I get the beep sound in the bios, so I think its definitely not the prob of os. something wrong with the keys isn't. Any suggestions or advice are appreciated, I ran the diagnostic of the HD, he took.

  Thank you

  manu555,

  If this happens in the BIOS as you note, that does anything have to do with the operating system.   As suggested from GMAC-R60, this indicates that the keyboard be bad or have a bad / intermittent connection to the system board, or something on the card system goes wrong.

  I will try:

  Checking the connection of physical keyboard:

  Remove and disconnect the keyboard - inspect the plug keyboard for any damage or visible corrosion.  Plug back in carefully and try again.  If the problems are still occurring, try...

  Clearing CMOS and reset the BIOS by default - sometimes you get somewhat stuck causing an abnormal condition:

  Remove the battery & AC adapter / CC.  Press and hold button power several times for an account of 5 each time.   Join AC and restart the computer.    Go into the BIOS and reloading the default values and save.  (there is an option to restore the default settings).  Stop.  Equip your battery and restart.

  Try to replace the keyboard - you can communicate with the service and order a keyboard replacement out of warranty or a local business partner of source on (if there are retailers of warranty allowed in your area, they will have the keyboard in stock or be able to order it).   Alternatively, check sales online - ebay, etc as you wish.

  If none of these steps solve it, so my next suggestion would be the system board, but I think it's rather unlikely.

  Best regards

  Mark

• Activation error: 0xC004C003 (stuck key)

  Recently built a new system, installed 64-bit Windows 7 Professional and got the error code above during activation. I have the diag, I noticed the Volume MAK and guess that's my problem?

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->

  Validation code: 0
  Code of Validation caching online: 0x0
  Windows product key: *-*-*-*-8FP28
  Windows product key hash: CjlYbHSXTcdJUCWcO5O1OoyFPPE =
  Windows product ID: 55041-008-1510867-86450
  Windows product ID type: 6
  Windows license type: Volume MAK
  The Windows OS version: 6.1.7601.2.00010100.1.0.048
  ID: {6B03CB01-E509-4A87-916A-9A0133B18E69} (1)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows 7 Professional
  Architecture: 0 x 00000009
  Build lab: 7601.win7sp1_gdr.140303 - 2144
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  OGAExec.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 109 n/a
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program Files (x86)\Google\Chrome\Application\chrome.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->
  Office details: {6B03CB01-E509-4A87-916A-9A0133B18E69}1.9.0027.06.1.7601.2.00010100.1.0.048x 64*-*-*-*-BATH55041-008-1510867-864506S-1-5-21-1003402068-3456339105-3563221133Gigabyte Technology Co., Ltd.. Power O.E.M. American Megatrends Inc.. F2 20130715000000.000000 + 00016FC3207018400F208090409GMT Standard Time(GMT+00:00)03109

  Content Spsys.log: 0 x 80070002

  License data-->
  The software licensing service version: 6.1.7601.17514

  Name: Windows 7 Professional edition
  Description: operating system Windows - Windows (r) 7, channel VOLUME_MAK
  Activation ID: 9abf5984-9c16-46f2-ad1e-7fe15931a8dd
  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
  Extended PID: 55041-00172-008-151086-03-2057-7601.0000-0122015
  Installation ID: 008286136663308063530912716450425962522303852524329185
  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
  Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
  Partial product key: 8FP28
  License status: initial grace period
  Time remaining: 37740 minute (s) on (26 day (s))
  Remaining Windows rearm count: 3
  Time to trust: 2015/12/01 23:36:48

  Windows Activation Technologies-->
  HrOffline: 0x00000000
  HrOnline: 0x00000000
  Beyond: 0 x 0000000000000000
  Event timestamp: 1:12:2015 23:21
  ActiveX: Registered, Version: 7.1.7600.16395
  The admin service: recorded, Version: 7.1.7600.16395
  Output beyond bitmask:

  --> HWID data
  Current Hash HWID: NAAAAAEAAwABAAEAAQADAAAAAQABAAEAln3kPkpFEDO4QtwVps804MKXntRQ1Dv1LDFudQ ==

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes, but no SLIC table
  Windows marker version: N/A
  OEMID and OEMTableID consistent: n/a
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  ALASKA APIC HAS M I
  FACP ALASKA A M I
  HPET ALASKA A M I
  ALASKA MCFG A M I
  FPDT ALASKA A M I
  SSDT AMD POWERNOW

  Your report indicates that you use a Multiple Activation Key volume license. For Windows 7 volume license customers are available only to companies making deployments to large scale of Windows.

  How did you get this license?

  If you have not obtained it legitimately, you can buy a genuine Windows 7 license. If this is the case, then follow the procedures below:

  If an organization exceeds the MAK activation limit, then its TI
  Professional can contact the activation call center to request
  other activations.

  You can try also reactivate by calling Microsoft Volume License Activation Center:

  Try the number listed here appropriate phone: phone numbers Microsoft Activation centers worldwide:
  http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx

• W500 Stuck Key error on startup with Thinkvantage key

  Hello.  I have a W500 with a 2nd hard drive through the Bay of cart.  I installed Win2008 Server Standard on the 2nd disk.

  When I boot (cold or hot), the machine and press the blue Thinkvantage button to get the menu of boot options, 90% of the time I hear a few beeps and then see the error "0210: Stuck Key 1 c" and told me to press F1 to go into the BIOS (why I want to go into the BIOS to fix this (, it's beyond me... thanks for the informative error message Lenovo and the reason why or where I have to go into the BIOS).  The 10% of the time I get to the menu, I press F12 so that I can choose an alternative boot and THEN device when I hit ENTER I get beeps and a similar or the same error on a go in the BIOS via F1.

  Now, the W500 is connected to a docking station/Port Replicator Lenovo support.  I do not exactly have the model # handy.  If I boot with the W500 disconnected the Replicator, the failure rate drops between 90% and on 25%...meaning, I press the blue button, I get the menu options of what I want to do, I press F12 to go to boot options, I select a drive, I hit ENTER, and everything is fine.

  It's weird.  I played with this laptop for hours with all kinds of combinations with or without the docking station, the number of times that I push button blue, cold / warm boots, etc.  There seems to be no rhyme or reason... that the failure rate decreases somewhat when you use is not the Replicator.  However, I really need to use the Replicator (I guess I could get Win2008 starting up and then anchor it but this still does not resolve the problem).

  First of all, Yes, I need to use the blue Thinkvantage button because my main drive is Windows XP and Server 2008 do not share the same boot manager.  Second, there is no other connected USB devices that can cause the machine to panic thinking that this isn't a boot (like my external drive) device.  Thirdly, the settings in the BIOS on the boot priority are a bit out of place because the blue Thinkvantage button is supposed to replace... but in the case you are wondering it is on cd/dvd first of all, 0 then, drive 1 third.

  Any ideas or have you seen this?  This error or problem occurs only when I press the Thinkvantage button... which means, if I just restart my XP disc starts just dandy.  But every now and then I need to start on my drive Win2008.

  Thank you very much in advance for your help!

  -Eric

  Eric, welcome to the forum,

  I don't know exactly why you get the key message stuck, maybe your pushing too early or too long?

  Why do not forget you the ThinkVantage button and just press F12 when the message «to stop the startup...» "watch, this will take you directly to the start menu and faster.

  Hope this helps

• Stuck Key 01 error 61 T

  Hello!

  One of my colleagues is an error while booting, it displays as:

  Error

  0210: stuck key 01

  Press to Setup

  I tried pressing F1 and it wont let me continue in the installer there at - it another way to solve this problem.

  Please advise!

  Oamedcophy

  This type of message means usually only one or several keys on the keyboard are stuck in the down position. You can inspect the keyboard to see if the keys are blocked mechanically. It is also possible that a spill of liquid caused one or more keys electrically 'Short' and watch the BIOS as if the key is stuck.

  If you are mechanically handy, you can remove the keyboard for inspection and cleaning. The material for the T61 series Maintenance Manual provides detailed instructions on the installation/uninstallation of the keyboard as well as the numbers for replacement keyboards. You can find used keyboards cheap on eBay, etc.

  By the way this post made me smile. This kind of problem and message goes back to the first IBM PC. I remember getting a BIOS message such as "error of keyboard: press to continue." The message was issued because I forgot to plug the keyboard in the system unit. It's a message ridiculous because if the keyboard is disconnected or broken how BIOS will detect that you pressed F1 or any other key?

• Hi all, I keep is typed in the password at startup box, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Hi all, I get a storm of +'s typed in the password at startup box upward, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Clings in the key on the keyboard? Wired or wireless keyboard?

  Try to run this program, copy and paste the result in a response. The program was created by Etresoft, a regular contributor.  Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.

  Etrecheck - Information System

  Reset an Apple Bluetooth mouse or Trackpad wireless keyboard (pairings and other common troubleshooting problems)

  Restart your computer, hold down the option/alt - P - R keys command before the gray screen appears. Continue until you hear the startup chime for the second time.

  Reset the NVRAM EXTRA memory

• Lenovo series k - disk error - press any key

  I have a brand new Lenovo computer. Its a center of the idea, and when I start it it says disk error - press any key. If someone has had this problem and to know what anyone on this subject? I work when I press "any key" but I'm worried that it could turn into a serious problem. Its only 2 days years the computer.

  Moderator edit: added detail to the subject.

  Oh never mind lenovo was trying to read my USB. Apparently you can not leave a flash drive in Lenovo you can HP. otherwise, I love this computer!

• Windows 2003 server the trial verson activation error: "invalid product key. Pls Help.

  I am trying to activate my trial 360days WIn 2003 version but the error: "INVALID PRODUCT KEY".

  Please any help?

  It seems that the trial was for the RC2 release of the server - not the release.

  It is time-bommbed and it has expired yonks.

• Acer W4 W3 bluetooth keyboard lag / stuck key

  Hey everybody,

  Everyone has noticed that there are problems with the Acer Iconia W4 with keyboard?  I have used with the W3 and had no problem at all, but now that I use on the W4, I often get massive lags (2 + seconds) between when I type something and show on screen.  He also picks up a character ('stuck' key) very often, with something like 20 or so repeating characters.  It's really annoying because not only what I need to remove super long chain of repeated characters, but the delete key gets stuck too and deletes everything I typed.  And this only happens when there is WiFi traffic, with the fact that it is the worst when I'm loading/downloading on the FTP servers in the back while typing... looks like the WiFi signal is ruin the BT signal.

  When I get on the W3, no problem.  I also changed the battery, just in case, without success.  Mouse Bluetooth has no problem but... Although I've read elsewhere here of people with mouse lag.

  Thank you all.

  Too bad this fixed it for me:

  https://community.Acer.com/T5/Windows-tablets/W4-Bluetooth-mouse-lag/m-p/257024#M10925

• Error - loading at start-up, my computer is giving a "loading error" «press any key to restart...» »

  At start-up my Sony Vaio with XP is to give a "load error" "press any key to restart '. .  Pressing a button any does not help.  I shut the computer down at least five times, and I get the same message every time. Help

  REX

  I ran fixmbr too, but you don't need to contact your manufacturer for assistance.

  It is extremely unlikely that any computer purchased at a store bought on this planet will have installed XP Recovery Console.

  It is extremely unlikely that any computer purchased at a store bought on this planet will be accompanied by a genuine XP installation CD bootable that can be used to start the XP Recovery Console.

  It's extremely likely that any manufacturer on this planet will send you an installation CD XP genuine for you can start in the Recovery Console.

  It is extremely likely that the majority of the posters on the forums is not any type of bootable XP media.

  It is extremely likely that the majority of the posters on the forums have never actually seen, possessed or otherwise come into contact with an XP bootable installation CD authentic in their lives, or if they already had in their possession, it is now nowhere to be found.

  I wonder why never support engineers offer this idea for the Recovery Console.

  (a) they do not know how
  (b) they are not allowed to post anything that isn't in a KB article
  (c) they are not allowed to post links to any place outside of Microsoft
  (d) your idea here

  You can make a bootable CD of XP (no XP media required) Recovery Console.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

• I get a "MGL FATAL ERROR 257.426" (error: open registry key) need help

  I get a "MGL FATAL ERROR 257.426" (error: open registry key) need help.

  How can I solve this problem?

  friends

  NTVDM is the program that emulates back and very old windows. There is none
  the reason that the NVidia Control Panel would need this.
   
  Registry programs, outside the cause of problems, often have a facility to cancel.
  Look in the program.
   
  Plan to run the restore of the system (type in the search on the start menu) to roll
  Back to a date that precedes ran you the program.
  --
  ..
  --
  "sam defcon" wrote in message news: 8c6a3fe2-af63-4 c 78-a203-b454e9a5876c...
  > I get the error message when I run GTA 1...
  >
  > and I can't open my control panel of nividia graphics card or play tank combat
  > without Ntvdm.exe crashing.
  >
  >
  >
  > Since I ran the Defrag registry BoostSpeed, the MGL error and
  > NTVDM. EXE crashes.
  >
  >
  > --------------------------------------------------------------------------------
  > friends
   
   

• When try to install the app in my new laption it displays the error "the product key you entered cannot be used to active windows on this computer".

  Original title: Activation of Windows 7

  Hello

  I have windows 7 Home premium dvd I bought from microsoft. When I tried to install the app in my new laption it displays the error "the product key you entered cannot be used to active windows on this computer".

  Please help me with this.

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->

  Validation code: 0
  Validation caching Code online: n/a, hr = 0xc004f012
  Windows product key: *-* - 8DTXM - 6FQ2H-BKDY9
  The Windows Product Key hash: tyrxnn4SwD4/dXymV2RGA4cQPHY =
  Windows product ID: 00359-OEM-9801782-52192
  Windows product ID type: 8
  Windows license type: COA SLP
  The Windows OS version: 6.1.7600.2.00010300.0.0.003
  ID: {1BCBE11C-A21C-46C6-99B2-41DA76B3FEFE} (3)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows 7 Home Premium
  Architecture: 0 x 00000009
  Build lab: 7600.win7_rtm. 090713 1255
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  OGAExec.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 109 n/a
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program Files (x86)\Google\Chrome\Application\chrome.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->
  [File mismatch: C:\Windows\system32\wat\watadminsvc.exe[Hr = 0 x 80070003]
  [File mismatch: C:\Windows\system32\wat\npwatweb.dll[Hr = 0 x 80070003]
  [File mismatch: C:\Windows\system32\wat\watux.exe[Hr = 0 x 80070003]
  [File mismatch: C:\Windows\system32\wat\watweb.dll[Hr = 0 x 80070003]

  Other data-->
  Office details: {1BCBE11C-A21C-46C6-99B2-41DA76B3FEFE}1.9.0027.06.1.7600.2.00010300.0.0.003x 64*-*-*-*-BKDY900359-OEM-9801782-521928S-1-5-21-1079193163-3130481270-3640039680Dell Inc.. Vostro 3558 Dell Inc.. A01 20150209000000.000000 + 000E9BB3607018400FC04090409India Standard Time(GMT+05:30)03109

  Content Spsys.log: 0 x 80070002

  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  The following files are available for download from the Microsoft Download Center:

  For a 32-bit version of the Windows Installer update for Windows 7 for x 86 based systems (KB971033)

  http://go.Microsoft.com/fwlink/?LinkId=150841

  or if you have a 64-bit version of Windows

  Install update for Windows 7 for x 64-based systems (KB971033)

  http://go.Microsoft.com/fwlink/?LinkId=152411

  Source: http://support.microsoft.com/kb/971033

  Please, run again in normal mode and copy Microsoft Genuine Advantage diagnostic tool and paste the results into a response for further analysis:

  http://go.Microsoft.com/fwlink/?LinkId=52012

• A virtual machine or the template with the same name is already registered. Server error: the specified key name or identifier already exists.

  Hi all

  I have a 5.5 esxi server just the a virtual machine running at the moment. I try to clone this as shown below:

  http://nchrissos.WordPress.com/2013/04/22/cloning-a-VM-without-vCenter-in-ESXi-5-1-free-edition/

  However, I get the error:

  A virtual machine or the template with the same name is already registered. Server error: the specified key name or identifier already exists.

  I have no vcenter (yet), and it's just the 1 vm. The virtual machine is turned off. I get this error regardless of the name, I said that when I choose "add to the inventory.

  All advice appreciated.

  Thank you

  Oh dear...
  you read bad advice on the internet and then you get also the stupid advice here.

  Ignore both!

  If you want to clone a virtual machine by copying - do it like this:

  Create new virtual machine with the wizard.
  Skip creating a disk for new customers.

  In Datastorebrowser copy the original vmdk to the new dir, which has been created by the wizard.
  Reopen the new VM and edit - assign the vmdk that you just copied.

  The procedure of the blog is not supposed to work.
  Sissine trick doesn't make sense either

• Plans test stops with the error 'Array with key "BB0050569F23260000-null" not found ".

  Dear gurus, I hope someone can help me with my problem.

  My SRM 4.0 Lab:

  • two servers vCenter v.4 + SRM 4.0 + EMC_Celerra_Replicator_SRA

  • two VSA Celerra with replication of work

  • two ESXi 4 servers connected to vCenter Server

  When I am trying to perform a recovery of the Test plan, I got the error 'Array with key as NULL "BB0050569F23260000" not found. "

  I guess it's something with recovery VSA, but cannot move forward, as I am a beginner in storaging.

  I've attached screenshots of the box of diag "Configure storage arrays", maybe this will help.

  Thanks in advance!

  without the hotfix SRA, you must rename your celerra VSA on the two sites do not contain not "-" in their names

  Itzik Reich

  Solutions architect

  VCP, VTSP, MCTS, MCITP, MCSE, CCA, CCNA

  EMC²

  where the news concerts

  If you find this information useful, please give points to "correct" or "useful".