Error: 16 problems

Similar Questions

• When the error is problem solver, I go to the store?

  When the error is problem solver, I go to the store?

  Please I need help English or Spanish

  If there is an error that you cannot solve at home, then yes the Genius Bar or authorized Service Provider Apple would be a good place to go. What is the error specific are you?

• Diagnostics Windows network, the error reads 'Problem with wireless adapter or access point' and fails to solve the problem.

  «Problem with access point or wireless adapter»

  Hi, I just bought a new laptop & I have the extreme difficulty to stay connected to the internet. When I run Windows Network Diagnostics, error reads 'Problem with wireless adapter or access point' and fails to solve the problem. Help, please... Thank you, Maria

  HI Maria,

  ·         What operating system is installed on your computer?

  ·         You have installed the latest drivers for wireless network card?

  Follow the suggestions below for a possible solution:

  Method 1: Start your computer in a clean boot state in order to check if the applications of third parties or startup items is the origin of the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: See these articles for solve wireless problems:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know if that helps.

• HP Officejet Pro 6830: My 6830 Pro Officejet a error Messege "problem with printhead. Through troubleshooting all.

  My HP Officejet Pro 6830 worked normally and then all of a sudden it started giving the error messege "problem with printhead.  It does no more than print all.  It doesn't let me do any troubleshooting procedures.  I use a wireless network on windows 10 64-bit operating system.  My printer is covered by the warranty.  What can I do to fix this?

  You will need to contact HP for the service, they will probably send you a replacement printer.

  From a post of Sunshyn2005, contact technical support HP see the following link to create yourself a file number, then call and it can help to expedite the appeal process:

  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
   
  File number and phone number are displayed.

• Windows Vista is not the right start, error message "problem event name: Startup repairV2.

  I recently got a game on Steam (GTAIV), but after that the match was my computer download was in place. I would have allowed a program through, thinking it was steam or game. I had a problem since then, now it is stuck on the beginning of initialization, it says I have errors:

  Problem event name: Startup repairV2

  Signature of the problem 01: AutoFailure

  Prob Sig 02: 6.0.6001.18000.6.0.6001.18000

  Prob Sig 03:6

  Prob GIS 04:786444

  Prob Sig 05: Corruptvolume

  Prob Sig 06: NoRootCause

  Prob GIS 07:0

  Prob GIS 08:2

  Prob Sig 09: WrpRepair

  Prob GIS 10:87

  OS version: 6.0.6001.2.1.0.256.1
  Local ID: D

  Same prob here is Looks like something is damaged

• I can't activate Windows 7, when I insert the product note key, which is an error 0xC004F063 problem code. What do I do?

  I can't activate Windows 7, when I insert the product note key, which is an error 0xC004F063 problem code. What do I do?

  Boost telephone:

  Activate Windows 7 manually:

  1. click on start and in the search for box type: slui.exe 4

  2. press enter on your keyboard

  3. Select your country.

  4. Select the telephone activation option and brace yourself for a real person.

  This is the Forum for Windows Update.

  You will get the best help for any problem of activation in Windows 7 install, upgrade and activate Forum. the link below:

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads>

  UTC/GMT is 23:41 Friday, January 20, 2012

• I can not open HP simplepass for my fingerprint, get the error "a problem caused blocking the program works correctly.

  HI.i have Windows7 ultimate.i cant poen HP Simplepass in my pc.it has been properly working befor I updat my windows
  Please help me! When I open HP Simplepass say this ERROR: {a problem caused labour correctly.please near deadlock of the program}

  That looks pretty bad answer at HP, since its their software.

  Try the HP forums

  If the first problem occurred 4 months ago who is probably too late to use a windows restore point

  You can try reinstalling the HP software

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=UK&LC=en&DLC=en&softwareitem=ob-82068-1

  See also

  http://h10025.www1.HP.com/ewfrf/wc/document?CC=UK&LC=en&docName=c02518653

• error 0xe0000247: problem in setupCopyOEMlnfW (file). now what to do?

  error 0xe0000247: problem in setupCopyOEMlnfW (file). now what to do?

  I found the solution:

  Windows 8 is the driver signing enforcement and does not pop up from the option 'install driver still' when installing netlimiter, so why Setup cannot complete.

  To resolve this issue, follow these steps:

  • In Metro user interface, by scanning at top right, select "settings".
  • Bottom right, select "change PC settings.
  • Select the "Général" tab on the left.
  • Under the "advanced startup" (the last option at the bottom), select "restart now."
  • In the next window, select "troubleshooting."
  • Select 'Advanced Options '.
  • Select "Windows startup settings.
  • When you restart, you can press '7' to the list of options and you won't boot with power off driver signature enforcement.

  Now you can install Netlimiter, reboot and it works like a charm.

  Thanks Ahmad Nezamipour of your head it as service fault, which led me to the right solution.

• I'm unable to print using firefox message is 'unknown printer error' no problems with other browsers

  I tried to print a coupon to an e-mail and the message I got was 'unknown printer error '. I am able to print from word and other items on my desktop as well as another browser. I can't print anything using Firefox. I have not updated recently, and the problem seems to have occurred spontaneously. Can help you.

  Try of the reset described here:
  
  http://KB.mozillazine.org/Problems_printing_web_pages#Reset_printer

  Make sure that you reset all the preferences for this printer.

• Tecra S1 - Vodafone 3 G card data - error 797 problems

  I installed a 3G data card and the Vodafone software on a Tecra S1 Windows XP runnig. When I click on "Connect" software Vodafone, it returns a message "Error 797 the modem could not be found" .

  In settings network - the 3G connection that the software creates has a red cross through it and says device not found - even if it is listed in the Modems in the control panel and can be queried.

  I have re-installed the card and the software several times. The card works on any other laptop I try, but not this one. Anyone know if this is a known issue with the Tecra S1? More important, a fix! -It starts to become really annoying.

  Thanks in advance.

  Hello

  As far as I know computers laptops with processors HTT have problems with cards Vodafone but your Tecra S1 has no processor HTT. Did you already try to disable the modem of Toshiba and try to use only a Vodafone card? I guess that you have properly installed the card and use it after Vodafone dashboard software.

• Error message - problem reading disc on Satellite

  I wonder if anyone can help. Was a virus on my laptop satellite scan to home (don't remember the model) 2 days ago, when the screen is blue and it was a mistake long message means the laptop has encountered a problem and stops.

  After that 2 hours, that the cell had not yet arrested so disconnected from the electrical network and removed the battery. To try to restart the computer, an error message pops up saying - CTRL + ALT + DELETE to restart problem reading disk. When I made the order it seemed be restart but then returned to the original statement of CTRL + ALT + DELETE. Tried again and amel and can't stand up boot.

  Someone had this problem before?

  Hello

  It seems that it's not possible access to the HARD drive or it is not possible to read the data on the HARD drive.
  I don't know why it happens, but first of all, you should check the boot sequence in the BIOS. If everything shows ok, so you should try to start form the OS cd and check if it is possible to install the new OS.
  If this is not possible if the HARD drive has a fault and you need to replace.

• software error 1394 problem

  Sir my does not.

  my software download iphone 4 1394 sow error

  The software on the iPhone has been jailbroken in the past? If so, this might be a reason for the error, and the jailbreak done your phone useless.

  In some cases, the security software on your computer is the cause, see this article to make sure that iTunes can happen on Apple servers:

  Solve the problems between iTunes and third-party security software - Apple Support

• Battery TECRA 9100 - NMI Error MESSAGE problem

  Hello

  I wonder if anyone can help me please.

  So what about the battery power, afer, start the system and after some time, a blue screen appears with

  HARDWARE MALFUNCTION

  CHECK THE SELLER

  NMI: I/O VERIFY ERROR or something like that...

  Anyone help is a star?

  It works perfectly while on the network. Is it a software or a hardware problem. recently istalled new copy of xp and all the drivers.

  Thank you

  Hello

  In my opinion, this is caused by a malfunction of the equipment.
  I found an interesting article about this Microsoft Knowledge Base.
  Check it on http://support.microsoft.com/default.aspx?scid=kb; EN-US; Q315223.

  Good bye

• Qosmio G20 error message: problem with the cooling system has been detected

  I'm trying to fix a Qosmio G20 (which is about 3 years old, it is no longer in warranty).

  Error message: Warning: a problem with the cooling system has been detected.

  I managed to remove the outer case and observe the operation of the machine, and basically one of the fans does not at all. The fan which is closest to the power connector seems to work very well (he seems to be turning a lot, do not know if this is normal), but the other fan who does not seem to move at all.

  When I put in place the case and on the machine, I noticed after a few minutes the vent of the fan working heat sink had warm enough, while led the non-working fan remained cool.

  I cleaned the fan from dust and have also changed the BIOS battery mode mode high performance, but the problem still exists.

  I would be grateful if someone could give advice if the problem is the fan or something else.

  If the fan is the problem, where I can buy a: i live in the United Kingdom?

  Hello

  I think there might be something wrong with the cooling module and the replacement would be necessary.
  Usually, this should be done by an authorized provider (ASP) in your country.

  Technicians could replace it with a new part and also could renew the thermal grease which is placed between the module and the CPU cooling.

  So contact the ASP in your country and ask for later handling.

  By the way; also, you can buy the cooling of the ASP module!

  Good luck

• C6350, install error - driver problem?

  Hi all

  RAN into this error while installing drivers for my C6350. I have had this printer for some time, it comes first in the management of problems during installation. Alos tried repeatedly, defraged and tried again, but still does not. I have obviously downloaded the driver several times just in case missing data issues.

  Any help really appreciated, John.

  This text has been in the header of message box:

  «C:\Users\xxxx\AppData\Local\Temp\7zS0935\Setup\... \Setup\hpzprl40.exe"-m...»

  This text was in the box, preced by Red Circle X

  "The system cannot find the file specified."

  Spec sys: Win 7 64 bit Premium / I7 Prc / 12 GB Mem / Avast! AV

  Downloaded from HP, driver: PS_AIO_04_C6300_Net_Full_Win_WW_130_140

  Restarted PC, router and printer before installing the driver, stopped Avast!

  Thanks for the reply to my post, but the suggested actions were not working.

  I clean all previous HP driver and temporary files, downloaded the driver, but when I tried to install I got an error that it could not find a 9diferent file to that stated above in the first post, I looked for the file in question and it's in the file!

  I'm not a novice around the PC, and as I mentioned earlier, this is the first time I ran a question. It probably has something to do with my Win7 OS...

  HP Universal driver, printer can now be used again (connected via a wireless network)

• Try to install PCI-GPIB on a Windows 7 System - x 64, variety of errors and problems

  I am trying to install a PCI-GPIB in my system Windows 7 after installing the version of NOR-488. 2 2.7.3.49152, I asked problems and the card itself interfacera not with any software. I tried to reinstall the driver several times without success.

  Problems encountered:

  No application included with NOR-488. 2 runs (welcome, troubleshooting, etc.). It will end with "The Application could not start correctly (0xc0000142)" when running.

  When I open 4.7.0f4, MAX I get no error until I try to expand the tree «Devices and Interfaces» At this point, I get:

  The nipalsys.dll plug-in caused an exception in the
  Function CmxSysExpertManager::InitializeExpert in the process of NIMax.
  See these files for more details:
  C:\ProgramData\National Instruments\MAX\Logs\20120325_152833-NIMax-
  00001BD4.log
  C:\ProgramData\National Instruments\MAX\Logs\20120325_152833-NIMax-
  00001BD4.dmp

  The log is attached.

  Finally, in Device Manager, the PCI-GPIB card comes with a yellow triangle with a point of exclamation, with the State of the device "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ».

  What should I do? I found somewhere the mention of problems when computers use EAP, but my computer is x 64, and so with 8 GB of RAM is not using EAP.

  Thank you.

  I tried driver v/3.03, corrected a problem.