Error 'ChunkSelector' of IMAQ 0xBFF69012 Max

Similar Questions

• Error 0xBFF6001F when trying to Max NI image acquisition

  Hello, before you start I want to say that I have read the previous discussions on this error code and tried the solutions, but none have worked.

  I installed SP1 of Labview 2015 and 2016 are going TO and have a grey Point flea 3 CCD (FL3-FW-03S3M) connected to my computer.

  Looking at the camera with the fly capture software I can get pictures but when I use NI Max I get error 0xBFF6001F. Any ideas on how to get the camera work?

  Also my device manager:

  

  Looks like you have an analog card (PCI-1411), you buy from in the first image. I guess nothing is connected to it and that is where the error is coming from.

  Image of Device Manager, it seems that you have installed Point Grey host bus driver. This will prevent IMAQdx to see the camera, let alone to benefit from its pilot link. You must use the Grey top driver utility of switching first opt for your device from the host bus drivers native to the operating system, then you want to change the camera to associate with the driver IMAQdx instead of Point Grey.

• Error in firmware PSC 2020 & Max connection time-out error

  Hello!

  My PCP 202O status LED will blink twice - which indicates that there is an error in the firmware (according to the user manual). I have already installed the latest firmware downloaded from the Web site of NOR and it says that I'm supposed to update the operating system of the remote system in MAX. When you try to update the system BIOS, it happens.

  Version on the target distance: 10.1

  Available on the host version: 10.4

  I'm a little confused as to which is the remote target and that is the system that hosts? He also says that the previously installed software will be removed if editing continues and it could damage the material so started or off so I'm a bit skeptical to proceed manually.

  I have error alsoreceiving messages in maximum errors in MAX are 'connected - no software installed' and connection to a remote device has expired. I wonder if this error occurs due to the firmware issue, or is it because of the timeout settings? What is the best? A period more or less?

  I'm new with this. Any info is greatly appreciated! Thank you!!!

  The target is your compact Fieldpoint.  The host is your PC that you are.  Given that the PC has a newer version, you will want to have the software downloaded to the CFP by MAX.  Of course, there is a small chance that you could lose power to the PCP if your luck is bad and that the power is off in the middle of the upgrade.  It would be better to have your diet for the CFP running off a battery backup UPS for safety.

  I'm guessing that the error is due to your firmware issue.

  If you are really unsure on how to proceed, it may be best if you contact DIRECTLY, they can help guide you through the update process.

• Error 'the database of the Max came out abnormally' in 2010

  The 2010 version installed and ran the MAX 4.7, it gave me this error. It worked fine when I used version 2009 & MAX 4.6. Does anyone have the same problem? I start the Configuration Manager of NOR, but it still doesn't work. I re-install DAQmx 9.2, however, it still does not - always gives me the same error. Can anyone help?
  

  I have corrected the problem. I downloaded the exe of the MAX database corruption to clear the database. After this, I restarted the computer, it worked. I'm running a few VI to the test and it seems to work very well.

• 1074395995 error in WriteJPEGFile IMAQ

  No idea why this is happening?

  Why this error occurs?

  What inputs you have connected in VI? I suspect that you are getting the error beause you do not provide the right track or you write to a directory that is limited.

• EZVPN connection fails with the error "Split tunnel higher than max attributes...."

  Hello

  We have ASA 5520 acting as the VPN server and the router Cisco 1941 as EZVPN client. These last days of customer is not able to establish the vpn connection. 1941 continuous router generates the below the log messages

  ---------------

  001569: Jul 22 ABC 12:19:05.883: CRYPTO-4-EZVPN_SA_LIMIT %: EZVPN (VPNGROUP) Split tunnel attributes (51) greater than max allowed split attributes (50)

  001574: Jul 22 ABC 12:19:07.835: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = vpn_user group = VPNGROUP Client_public_addr = Server_public_addr =

  004943: Jul 22 ABC 11:32:42.247: % IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the table fragment has reached its maximum 16

  ---------------

  Future prospects for aid and the suggestion of experts

  Thank you

  Israr Ahmad

  Yes, your split tunnel access-list is too big, and he has reached the maximum number of lines.

  Try to reduce the number of ACL for your tunnel of split ACL maybe combining the subnets if possible.

• OAM error messages: how to set max authn_try_count?

  OAM 11 g gives a set of external error codes (OAM-1-OAM - 7) who treats of usecases as user ID not valid user account locked user account disabled, Invalid credentials etc.
  However, when the user tries to connect, OAM allows a fixed number of attempts before you throw those errors. This is followed by a query parameter: authn_try_count. The value default no for attempts is 5. Until the 5th attempt, OAM raises just an OAM-1 generic error code that launches a generic message: 'a bad user name or password has been specified.
  
  This causes a problem of usability. It make much sense to ask the user to enter the credentials of 5 times to let him know that his account has been locked in the first place.
  Is there a way to set this threshold to 0, so that users can see the error messages the first is invalid try itself.
  
  Or, is it possible to propagte the LDAP error underlying messages on the page of external login itself, so that in the event of a locked account scenario, the user can be given a relevant during the first attempt itself error message and can then be redirected to a more appropriate page.

  Hi serine,

  Yes, you can change the maximum attempts by changing the value of MaxRetryLimit in the config.xml file - oam (unfortunately, it is a modification of file, so please save the file first) and restart the WebLogic Server. Please see Note 1358844.1 for more details.

  Kind regards
  Colin

• Error 1074396120 has occurred to IMAQ FFT

  Hello. I'm new here. I am attaching a file VI here that there is a mistake once I try to filter my loaded image. The error occurs on IMAQ FFT and he says, it takes a picture. Can you please help? Thank you.

  version of 2013.

• IMAQ Vision: IO file error

  Hello

  I get the error in the subject, trying to open a file that was acquired from a phone android via the command "adb shell screencap.  I have attached the criterion vi and the image.  I can't seem to find the solution to open this file without error happening on "imaq readfile.  I tried image different types on imaq create and also tried the other way to read that an image file named "imaq read info image and vision.

  I see that I can use the 'imaq getimageinfo' tool to get the parameter image correctly.  I can't get labview to open the image without error, given the tools available.  Help, please.

  P.S. I'm under labview 2013 sp1.

  Thanks in advance,

  David Jenkinson

  Confirmation: Your product-1074395993 code error code when executing "IMAQ ReadFile" during the reading of this png. I don't know what could be the problem with this PNG. To work around the problem, you can use 'Read the PNG file' of the 'Graphics Formats VIs"which doesn't have this problem.

  

• USB camera not found EXE, IMAQ void VI error running program

  Hi, dear guys and managers on board

  I'm a new engineer in Germany. Recently, I've converted a program of USB camera that is used to read image of LabVIEW 7.1 version to version of LabVIEW 2010 barcode matrix, with LabVIEW 2010, module Vision Development, software vision purchase August 2010 is installed.

  The program works well, and I have generated an EXE file to run the tool on computers without LabVIEW 2010 is installed.

  I installed the runtime LabVIEW 2010, Vision Runtime Engine(evaluation version) and going TO (evaluation version).

  However, when I run this program, I still have this error, saying that "IMAQ Read Data Matrix code bar 2" not found.

  Would someone please so kind to give me any suggestions? Thank you very much!

  
  

• 3D studio Max 2010, cannot start. Identification of the error of debugging/possible?

  Used 3D Studio max 2010 (perpetual teaching license) for well over a year. The program does not start for some reason any in the last two weeks. Vista32 bit version home said that the program has stopped working (before you get to the boot screen) with no identification on the error. If 3D Studio Max ran that there is software identification own error built in but as is happening this crash of the program until the program starts there is no way to know what is the cause. The question here is, is there a program hidden in Vista or downloaded from somewhere like Cnet I can run everything trying to start 3D Studio Max, about what is at the origin of the program that worked very well die suddenly?

  I tried uninstalling/reinstalling as well as the repair feature in the control panel > programs & features, but nothing works to alleviate this problem. Help & thanks for any information on that.

  Thanks again for your help because I don't know exactly what's wrong, but it's fixed now. Here are the steps I used just in case someone else has the problem & solutions.

  Restoring the system was such that it was more than 30 days, when it all started so I went with suggestion of Marilyn to the subject to start with a clean boot of Vista. I don't know if it was going to arrest her or not, but as it has system attendant, I wanted to ensure that he would not scramble things upwards trying to find out what the problematic program could be first turned off Avast antivirus (free).

  Since the boot, I started by turning on just autodesk licensing service, and then the apple programs, nvidia & adobe I was sure that those who will not be a problem because they have been on this plu pc of 3DStudio Max with little problem. Finally, I went through the list of services, turn on & restart and be able to open 3DStudio Max. When he finally got the end of the list, the only thing left to start near the top of the boot was avast antivirus (in the services menu, it's on, but in the menu it has been disabled until I turned it avast turn it back on.) Once I turned avast activated, I turned on the services menu then to start during the last entry on the list. From there, I got an error message when you try to start vista had some issues that needed to be repaired. After telling the repair through the machine got fined office since just before done restore point cleaning starting the process.

  As I imagine that Avast could still be a problem, I did a complete uninstall of it & all Avast/Awil (a software developer) files from the computer. Then as an experiment, I installed the latest version of the program to test & see if 3DStudio Max will still crashing like all services had been turned on & this program could open. After Avast was completely installed I went open 3DStudio Max & it works fine now so I guess it was something fixed during the repair and/or process the older build of Avast antivirus (which was the only program not turned on the list of services in this process of cold start).

• Financial reports of Hyperion Studio error. No max connections exceeded.

  I met an error en Studio, it says Max No of connections exceeded.
  
  Happened twice in this month, every time that happens to restart the statement and analytical framework. Can anyone suggest where I can increase the number of allowed connections max?

  Ok... My bad...

  You tun serviceconfig.sh under Hyperion_Home\products\Foundation\workspace\bin to bring up the GUI, and then in the menu layout, you will see remote service Configurator, select that and provide credentials. After you sign in, it should y RM1 and SB1. You will need to go o RM1 and SB1 properties and then to increase the connection. Need to reboot for it to take effect.

  Let me know

• WSN-9791, management to the 3202 errors

  I have setup a 9791with 3202 and attached to a 250 Ohm resistor to measure a 4-20mA signal to the 3202 AI0. I'm always out of measing the input voltage and I also check the voltage of battery, link quality, external power supply and error messages with the management of simple mistakes. Everything seems to work properly. Now I disconnect to the 3202 and remove the batteries. Surprisingly, the voltage to AI0 remains its value, the battery voltage remains the same, it shows as external is present and the error handling will not display any errors. After 3 minutes MAX will show that the signal was lost. The VI shows that the external power supply has been disconnected. All other values remain the same

  I'm using LabVIEW 2009FDS and I don't have a Pioneer or any additional software. I have updated the firmware of the 9791 and 3202 to the latest revision.

  How can I display in my VI that the signal has been lost? MAX seems to be able to do so, but only after 3 minutes. Why the management of errors never poster no matter what? Why is the quality of the binding the same when the signal is lost?

  Thank you

  Hi wv,.

  I'm sorry that you are not satisfied with the features of the WSN material.

  You need not actually a time accurate system to check if your data is obsolete.  What you need to do is check compared to the timestamp of the last time read you.  In this case, it matters really very little whether the internal clock is 1903 or 2011.  You check just to see if the data was updated to say the past 3 minutes.

  As far as the quality of the connection goes, it's also a common variable and therefore likely to be the same phenomena as the other values of nodes.

  Have a great day,

  Chris V

• VISA 1073807343 errors and 1073807202

  Hello everyone,

  I have several issues with the VISA 5.0.3 and LabVIEW 2010 SP1, and I don't know if or how they are related, so I'll post as much information as I have here. Please excuse the super post long, just trying to be thorough.

  Error BFFF009E (same as 1073807202 I think) appears to the MAX aperture as seen in attached ss1. When you try to open the VISA Interactive Control (IC), I get the message "failed to initialize the library VISA. The VISA interactive control utility will leave. "When I open any VI with a VISA resource and try to click the drop down arrow on the right to see the resources available, the arrow remains derpessed during a second, no field drop-down list is displayed, and then it returns to its original blank State. These problems all live together now, but before I could select BT VISA resources and use VISA IC, while I have always seen the error MAX.

  I tried to fix VISA, as well as VISA uninstall-reinstall 5.0.3 which I believe is the most recent version. No change. I also checked that visa32.dll exists as suggested in the article below. See systeminfo.txt attached to the installed software.

  http://digital.NI.com/public.nsf/allkb/1D1736BFD24A09878625742500241386

  This error seems to be related to an oscilloscope Tektronix DPO 2014 I connected via USB (or maybe something to do with TekVISA?). By this I mean that if the scope was connected when my computer started, this error occurs. When the field is not connected at startup, I don't see the same problems as above. Instead, I get...

  Error 1073807343 (BFFF0011) when you run a VI with a VISA resource to a serial device (see ss2), or connecting to the device in IC of VISA (see ss3). I also always see the error of BFFF009E to the MAX, but not the other problems on front. I can connect to these serial devices in hyperterminal and communicate very well here. Seems similar to the post below and also, I can't find visaconf.ini, but the solution does not apply as I LV 2010. In addition, ironically, I use VISA very well talk to the scope (whether to the MAX or LV) via USB if I connect after booting.

  http://forums.NI.com/T5/instrument-control-GPIB-serial/using-HP34401A-in-LabVIEW-yields-error-code-1...

  I use series of USB adapters made by Ultra (http://mail.ultraproducts.com/product_resources.php?cPath=35&pPath=782&productID=782 ) to go from instruments of series to my USB ports and the computer I'm unfortunately has no serial ports to be tested with, nor do I have another brand of the adapter. I know these converters can sometimes be a VISA problem, but I was certainly with it even without problem before.

  They that all seem to have intermittent problems, because I have seen both before as I have developed and pushed to go to strange as things exchanging (apparently identical) USB extension cables or restart a dozen times. This issue has been driving me crazy for weeks, I am looking for help to try to solve it finally.

  Thank you

  Ratti

  I think I got especially. Looks like it was TekVISA who got in the way, and if Visa32.dll was in the right place, it appeared (in properties > details) as the version of Tektronix, not the version of LabVIEW. After you have uninstalled all Tektronix as well as NI-VISA, he had disappeared, but no money to install or repair NI-VISA would be replaced by a version of LabVIEW Visa32.dll.

  However, with the help of the article from the link below, I discovered that the repair of the installation of the driver NI-VISA DURATION is what replaces Visa32.dll, as opposed to NO-VISA just as messages of error and other links seemed to suggest.

  http://digital.NI.com/public.nsf/allkb/B283196340462DFD86257633006DC799

  Now all the VISA stuff works again, except of course for the scope of Tektronix. I'll keep this battle for the future. Guess I just needed to talk to myself for a while.

  -Ratti

• 88705 error on PCI-6280

  After obtaining the 88705, PCI-6280 card error has been removed but MAX still sees the jury and cannot be deleted in the attempt to re - install in the new location.  Any ideas?

  TJ,

  When you say that it cannot be deleted, the option simply in gray? It is after the card has been removed from the system completely?

  Could you also tell me what version of the DAQ hardware drivers you are using as well as the operating system with this computer?

  I found a knowledge base about the error 88705 you can pass by this way: http://ae.natinst.com/public.nsf/webPreview/89A6279147AA994A862572DF00491BCA

  The issue might be with MAX or with a process runs do not, then let me know everything above and if the KB help at all so we can we this necessarily so plu. Thank you.

  Timothy