Similar Questions

• Help on PCI 6280 connector

  Hello everyone

  I'm about to buy a card daqcard pci 6280. However, there is always a little doubt about it:

  The DAQ card connector, is it male or female?

  I need to be a male, so it can be directly connected to my sensor cable. But if it's a female, I would like to know if the cable (what I can buy with the DAQ card) is a male/male connector.

  I would appreciate your help and quick asnwer.

  Thanks for the help and see ya.

  Hello

  Connectors Digital PCI data acquisition card is men.

  If you have any doubt please contact me.

  Thank you.

  Best regards

• Problem with connection diagram - BNC-2110 to PCI 6280

  Hello

  I want to read analog input using BNC 2110 as an interface connected to the PCI-6280. In the first step I want to use the Signal Express to see only the data, but when I choose one of the input and then string I want to see the connection, I get this message:

  ------------------------------

  Connection scheme tool does not send the accessory on the connector 0 of your device:
  BNC-2110

  Please select one of the following accessories to display the supported connection diagram:

  Support for accessories:
  SCB-68

  CB-68LP

  TBX-68

  CB-68LPR

  SCC-68

  ------------------------------

  What should I do in this step?

  Hi MiladAk,

  There is this sentence in the Manual "the BNC-2110 is only intended for differential analog input signals. The 16 channels HAVE on PCI-6280 are mapped to 8 connectors BNC AI0 - AI7 on BNC-2110. HAVE [n] with I [n + 8] represent a differential channel. This means that if you select channel differential AI0 in Signal Express with Terminal configuration it will also use AI8. These two channels is represented by a single BNC connector (connection central driver is positive = AI0, negative connection is shielding = AI8).

  Best regards

  CaravagGIO

• The attention! Error initializing PCI express slot 4 (for a PCIe used in the PXI-1033 chassis)

  Hello

  I have problems with my PXI system. When I try to contact the 1033 chassis using his high card my computer does not recognize (the PC displays the message during the start-up stage: "alert!) Error Initializing PCI express Slot 4). It was working fine before, but the chassis has been disconected with the PC on. I read that it may cause failures of communication, but I have not found a good source for this problem. Could someone help me with this problem?

  Thank you very much!

  Victor

  Hi Victor,

  Can you check something for me? One, can you try to disconnect the cable between the PXI and PCIe cards and try to restart your machine. When you do this, you still see the message? I know that you mentioned in your first point that the chassis is turned on when you see the error message, so I'm just trying to clarify what you mean by that.

  Also, it is quite easy to plug in a cable express MXI upside down, so even if point 2 you said that the links appear to be good I had to check to make sure that the cable is properly connected. You have additional cables, you can test?

• Win7 64 bit error code pci\ven _1217 & dev_7130 & subsys_13c610cf & rev_01

  I have a fujitsu a6020 notebook that I have upgraded to vista 32 bit to win 7 pro 64-bit and after a windows regularly update, I get a problem with mass storage controller, and a unknown device driver. The first error indicates error code pci\ven _1217 & dev_7130 & subsys_13c610cf & rev_01\4 & 47add43 & 0 & 1bfo. the second is acpi\fujo2e3\2 & daba3ff & 2. Can someone explain how to solve these problems.

  James

  It is a driver of SCSI controller which you should be able to get Fujitsu.  If there is no current driver, you can install an older driver using compatibility mode.

  To run in compatibility mode do the following:

  Click with the right button on the installer > properties > compatibility > choose OS

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows?SignedIn=1

• error system PCI bus/device/function 000 h, then again with the number 0200 h

  last night when I went down tmy computer and is gone sleep on that I left it and it usuallty just goes to sleep. Today, I am home from work to try to remove the mode "Eve". It wouldn't even turn it off and turn it back on to notice that my computer somehow managed to delete the operating system. so I don't have xp on my computer. I can not even access bios to check if something I messed up. So I decided to try booting with the disk. and this is where im stuck. I'm quickly beginning to hit 'r' to reformat the computer and install an operating system. He goes through when he's trying to do. I'm prompted with the error message
  System error ' PCI Bus/device/function 0000 h.
  PCI Bus/device/function 0200 h system error. "

  After a few minutes of doing nothing it says under that
  "Hard disk write error!

  Press a key to continue. "

  now, I thought that the memory of my laptop may be losing the connection. I've checked everything and it's all warm in its place even the hard drive.

  is there anyone who can help me?

  Hi DrewHuble,

  Given that you have made to the formatting when you are prompted, it looks to the operating system is removed.

  If you have important data on the computer, I would say that you wake the computer to any tech store to back up data and then reinstall Windows XP on the computer.

  Install, reinstall, or uninstall Windows

  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

• When setting up my Ethernet 9188 cDAQ chassis, 88705 error was encountered

  
  

  Hello Joseph92,

  I just found a very similar case, where the error has been resolved by repairing NI DAQmx and NI LabVIEW. You can do this by going to the Control Panel/uninstall or change a program/software from National Instruments, then choose all DAQmx and NI LAbVIEW options and finally click on repair.

  It seems that the problem is in a LabVIEW web services configuration. And repair software to fix this problem.

  Greetings and let me know if this was helpful

  Guillermo O,.

• Error initializing pci express slot machine

  
  

  Hello

  Can you make sure that you first power of the PXI chassis, then wait a few seconds, and then turn on the PC.

  This error can occur if the PXI chassis is not fed first.

  Unable to Boot the BIOS since then using MXI Express
  http://digital.NI.com/public.nsf/allkb/05B7131814A5DDA38625710F006BB098?OpenDocument

  If it doesn't, it would be useful to update the BIOS.

  You can also try it on another PC to make sure that the problem is not related to the PC.

  If none of the troubleshooting steps in the work, I suggest that you call us for more troubleshooting and/or send your material for repair:
  NI.com/Ask
  (phone for france: 01 57 66 24 24)

  Best regards

• Driver error issues "PCI Simple Communications controller has not a driver"

  I am trying to connect my printer, an hp deskjet 2050 printer, but I get the message that PCI Simple Communications controller does not have a driver and PCI Serial Port doesn't have a driver... what should I do?

  William

  Go to HP and download the driver, then install it.

  Most often when a device does not work, it is because the driver is damaged. Re-install a new copy should help

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/   (also works on Windows 8)

• Satellite in a series - error: conflict of resources - PCI on the card mother BUS: 09

  What started it stops early on with the error:
  -Conflict PCI resources on the card mother BUS: 09, device: 01 function: 00
  -Conflict PCI resources on the card mother BUS: 09, device: 01 function: 02
  -Conflict PCI resources on the card mother BUS: 09, device: 01 function: 03

  I have the option to continue with F! that works.
  I use Windows 8 at the moment, but it seems not so stable. Above mentioned mistakes occurred that after awhile, I upgraded to W8.

  Do I need a new motherboard, or y at - it another option. What does this error mean in normal words.

  Hmm, it looks like a problem with the motherboard or part connected to the motherboard.
  The error indicates this device 01 because of controller 09 conflict
  Have you tested the RAM?

  Recommend doing this! You can use a tool like Memtest or similar.
  Maybe it isn't that a Ram problem and new modules could solve your problem.

• cDAQ-9172 error message 200485 in Labview and 88705 Max

  My company has had this machine for awhile not operational.  I decided it was time to get this thing running but continue to flock to the top with a 200485 error when I try to run Labview and 88705-error when I try to change anything in the cDAQ-9172 runs at MAX.  I'll try to update the software and reinstall the drivers in the hope that it is a mistake to simple communication from the device to the computer, but in case it's something more serious that I am not seeing that I wanted to post this in the hope that someone might have an answer.  Thank you

  I would start by checking the device loader OR. Error 88705 in MAX is caused because the Windows Service OR device charger has not been loaded. Below is an article about starting the service knowledge base.

  http://digital.NI.com/public.nsf/webPreview/89A6279147AA994A862572DF00491BCA?OpenDocument

  Thank you

  Steven Koo

• Bug BIOS PCI found for Equium A110-233 during startup

  Hi all

  I get an error of "PCI BIOS bug found" when that I start my Equium A110-233. It gives a number, but the error flies by so fast, that I'm not.

  I have not noticed errors running the computer except that my SD card reader does not work, but because I am under that Linux Ubuntu Gutsy Gibbon was based. I am aware that Toshiba is not supported for the drivers for this device.

  How bad are errors of BIOS bug? It needs fixing?
  I can query the operating system to find out the bug number BIOS / details?
  Can it be fixed with a BIOS update loaded via the Windows emulator or virtual machine?

  Thanks for all the ideas in advance.

  Hello Rob

  You can use Windows XP Home edition on your laptop with no problems?

• Satellite P300D - h - 13 PCI in conflict

  Hello!

  Some info:
  OS: win Vista Home Premium 32 bit
  BIOS: 3.30 - WIN

  After one of the windows updates after I restarted my laptop I get errors:
  --------------
  ERROR
  Resources - Bus controller conflict series PCI on the motherboard
  Bus: 09, device: 01, function: 00
  ERROR
  Resources - Bus controller conflict series PCI on the motherboard
  Bus: 09, device: 01, function: 01
  ERROR
  -Conflict PCI on the motherboard resources
  Bus: 09, device: 01, function: 03
  --------------

  With F1, I just confirm and the system to boot normally. But then I realized that firewire card and multi drive no longer works. I checked under devices and I have problems with the following devices:
  ----------------
  IEEE 1394 Bus host controllers
  -OHCI Compliant IEEE 1394 Host Controller (not enough resources)
  Other devices
  -Conroller of memory PCI (no driver installed)
  -Controller of Bus SM (no driver installed)
  ----------------

  I tried to:
  -cancel the last windows update,
  -load the bios default
  -reset the bios with remove the battery from the motherboard and waited for 1 hour
  -the latest version of the bios reflash,
  -Reinstall everyhing Rescue CD.

  Nothing helps. Errors are always present.

  Y at - it something more, that I could try o or is it the failure of the motherboard?

  Kind regards
  Sasa

  > Is there something more I could try o or is it the failure of the motherboard?

  Well, if you have already tried to restore the system using the disk recovery Toshiba (your written you already tried this procedure) and this did not help to resolve the issue, the problem could be linked to the fault of the motherboard.

  The resource conflict error message indicates that certain devices (part of the motherboard) causing the problem.
  In your case, it s PCI Serial Bus controller.

  From my point of view of the few there are not many options for repair.
  I think that the motherboard must be replaced. :(

• Standard VGA driver error on Win7 fresh install

  Hey guys:

  OS: Win7 64 bit

  Product: b0p18pa #ab4

  Model: dv6-7007tx

  GPU: NVIDIA Geforce GT 630 m

  on the new install of W7, I have 2 instances of 'standard VGA graphic card' that is 'installed correctly' (ID below):

  PCI\VEN_8086 & DEV_0166 & SUBSYS_181B103C & REV_09
  PCI\VEN_8086 & DEV_0166 & SUBSYS_181B103C
  PCI\VEN_8086 & DEV_0166 & CC_030000
  PCI\VEN_8086 & DEV_0166 & CC_0300

  one that shows an error:

  PCI\VEN_10DE & DEV_0DE9 & SUBSYS_181B103C & REV_A1
  PCI\VEN_10DE & DEV_0DE9 & SUBSYS_181B103C
  PCI\VEN_10DE & DEV_0DE9 & CC_030000
  PCI\VEN_10DE & DEV_0DE9 & CC_0300

  After trying several times (automatically or manually) install the Nvidia drivers, it displays an error saying: "you must install an Intel driver first.  I know it's the HP forum, but I tried to contact Intel with no luck on top of each Intel driver that looks even vaguely relevant in train. (more what mistake during the installation to mention my computer does not have the conditions required for installation).

  I tried to update the drivers automatically through overlapping windows on disable or uninstall and reboot, but the same problem keeps arising.

  any help would be greatly appreciated. I struggled with this thing for over 2 days now :/

  Cheers!

  Hello

  Try to install the following drivers I have the same order.

  Driver and Intel Chipset Installation utility

  Intel Management Engine Interface (MEI) driver

  High definition (HD) of Intel Graphics Driver

  NVIDIA driver graphic of high definition (HD)

  Optinal

  BIOS

• PCI device & problem Driver control Ethernet in HP 2000-2128TU

  Name of the product - HP 2000-2128TU

  Windows 8 and 7

  After using a few months Windows 8 in my laptop suddenly I did deal with any Modem does not work. Unable to connect to the internet. Then I found after a huge search with some error in PCI Device Driver, Mini Port network.  And I can not solve. Then I downgrade mu camera to Windows 7. Now each Modem works well, but I have the same error my Ethernet Control PCI Device Driver & driver.

  Help me how I solve the problem. I don't know yet what kind of problem it is. but I got the error in the other devices section of Device Manager.

  Hello:

  Here are the links to the W7 drivers you need for these two devices:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-104713-1&CC=US&DLC=en&LC=en&os=4063&Product=5305458&sw_lang=

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-104710-1&CC=US&DLC=en&LC=en&os=4063&Product=5305458&sw_lang=