Error code of port 0 ahci XPS 8100
Hello
I turned on an Ahci port device error 0 ft press to take over the message to the computer. When I did, I reached the cmos utility for installation. I have left alone and pressed for and when the computer is started again, I insisted on trying to boot into safe mode. But I kept getting the same message. I put the Dell utilities and drivers in the computer, and the result is 'failure' code 146. (I did with so gleaned in this forum.) Does this mean the hard drive died? If so, what are my options?
Do I need a new computer or just a new disk?
Thanks in advance for your help,
Jane
What version of Windows?
If the drive has failed, there is no need to reinstall Windows on it. In addition, you lose everything on the disk, if you have not already lost him. I hope that your files are backed up.
If it says that the disk is too small, looks like you are trying to perform a "parallel" installation (for example, a second) of Windows instead of reformat and do a clean install. But even once, if it does not, not worth it...
Before going further, you can check that the SATA hard drive data cable is correctly connected at both ends (for example, drive and card mother), and you probably want to remove the motherboard battery and press/warm for about 30 seconds power button before you reinstall the battery.
Do these two will prevail on simple problems before you have to replace the drive. Always turn off, unplug and press/hold power button for about 15 seconds before opening the case.
Regarding the size of the drive, you want a desktop (not a notebook drive) SATA3 drive, and depends on how much storage capacity, you want / need and budget. A 1 t or 2T car probably should work well.
Or you could install a solid state (SSD) drive that will greatly increase the performance, but the cost may be higher for a smaller drive.
Anyway, once you have installed the new drive and loaded the drivers, Windows updates, software etc., you can install your old drive as a secondary drive and see if you can retrieve all the files that are not backed up on external media.
And if you opt for a SSD, you can still install a second hard drive for storage. Even if you can recover your existing files on the old drive, I'm not sure you should trust him ever again. So be sure to erase completely before use or take a hammer to it and destroy it.
Tags: Dell Desktop
Similar Questions
-
Failure of the Activation of Windows 8 and 8.1: 0xC004C003 error Code
I recently updated my window preloaded 8 to 8.1. However, after the update, it accepts not my old window key 8 and asks me to activate with a product key. Here is the error code: 0xC004C003
My DELL XPS came with a preloaded copy of window 8 and yes there a 8 to the rear window sticker
and fully enabled until I updated to windows 8.1. And as far as I know, system which comes with preloaded window 8 has its key product injected into the motherboard and 8.1 is free for users of window update 8.
So why the update do not accept my window key 8 and ask me a new key? I know that my 8 window key can be used to any other system because the key is injected into the mother board and I don't even know the key myself.
So what can I do now to my window be reactivated?
No more frustration, it's that I can't go back to windows 8.
I tried to reset it to the original image using DELL backup & built in system recovery software.
However, after the image of the factory it does not accept embedded product key.
Here are the details of the Diag report:
< licensingdata=""> 6.2.9200.16384 SL_LICENSING_STATUS_NOTIFICATION 0xC004F009 SL_GEN_STATE_INVALID_LICENSE 0 0 0 3667 T 00179-60217-82995-AAOEM 6.2.9200.2.00010300.0.0.101 Windows 8 x 64 kernel 9200.win8_gdr.130531-1504 Pacific Standard Time(GMT-08:00) 9e4b231b-3e45-41f4-967f-c914f178b6ac operating system Windows (r), channel OEM_DM 55c92734-d682-4d71-983e-d6ec3f16059f 6ebfad4c-bf1e-b490-0792-af4805004a2e 05426-01796-021-782995-02-1033-9200.0000-2892012 OEM:DM 013973156267325267434076636570069414537104826838472680809750724 fake S-1-5-21-3370853396-3622322263-2384857213 1033 1033 1033 SIGNED_INFO_PRS_SIGNED true 0 x 00020001 DELL AS09 Dell Inc.. XPS One 2710 20131223172100.000000 - 480 < icensingdata=""> < healthcheck="">PASS < ealthcheck=""> < genuineauthz=""> 0xc004f200 < enuineauthz=""> < iagreport="">To activate Windows 8.1 successfully after you install the latest version of the BIOS.
-
Dell xps 8100; Disk failure hard error 2000-0142 0 self test status 79
Hi guys, I was wandering in the forums for a few hours, now looking for ana response to this question, and can't find anything clear. I have a XPS 8100 that I run a diagnostic and received a 2000-0142 error code that says MSG: error code 2000-0142 hard drive FAILURE 0 self-test status: 79 based on what I read in the forum is that there is a disk failure, and the only recourse is to solve the problem in my view is to replace the drive. Firstly, can someone please give me an absolute confirmation that it is indeed what I have to do, or is there something else I should do to fix this problem first? If a replacement drive is there someone could please tell me how can I do to get my OEM software off the coast of the partition recovery and on my new drive. I now office preinstalled and, of course, premium Windows 7 I would like to see on my new hard drive and I was not provided with one of the disks at the time of purchase. Thanks in advance to all those who respond
Hi XPS8100kid,
Welcome to the Dell Community Forum.
The 200-0142 error is for hard drive failure and you need to replace the hard drive.
Since the hard drive has not, you would not be able to access the partition recovery on it. Data would be lost and the software already installed on your computer will need to be reinstalled.
Windows 7 will need to be installed on the new hard drive. Please click the link below to get the procedure of re - install Windows 7.
If based in the United States, you can ask for the backup drives by clicking the link below:
I would like to know if additional assistance is needed.
Thank you and best regards,
Babita S
#iworkforDellFor easy access to the drivers, manuals and updates, please visit our Support Site .
-
Update Windows in Windows 7 will be not updated.
Error code 80244008.
Troubleshooting report says 'device or resource (web proxy) is not configured to accept connections on port "8080".
You may encounter temporary connection errors [for example, 0 x 80244008] when you use Windows Update or Microsoft Update to install updates
http://support.Microsoft.com/kb/836941What application or antivirus security suite is installed and your current subscription? What anti-spyware (other than Defender) applications? What third-party firewall (if applicable)?
A (another) Norton or McAfee application has already been installed on the computer (for example, a free trial version which is preinstalled when you bought it)?
~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
That - 1073807252 serial port error code means?
Hello
I have a client with a prototype device that uses a USB OR for RS-422 interface connected to a PC. On the LabVIEW, the following error code application of the serial port is seen:-1073807252
What does this code mean? Is there a place where serial port error codes are discussed?
Thank you.
Bob
Right-click on the cluster of error, and then select 'explain the error.
Alternatively, use the Simple (or general) error handler.
He tells you: VISA: (Hex 0xBFFF006C) an overrun error occurred during the transfer. A character not read in the material before the arrival of the next character.
Basically, this means that you do not read the serial port stuff pretty quickly.
-
I WORKED ON IT FOR DAYS, BUT I'M UNABLE TO GET AUDIO ON MY DESK! I'M ALL TROBLESHOOTER IMFO LLA AND MAKE ALL READERS MADE AFTER ANY UPDATE DEVICE MANAGER I GET AN ERROR 10 MESSAGE AND OR CONTACT THE SERVICE PROVIDER BUT I THINK IM DISABLE SOMETHING AND IM READY TO TEAR MY HAIR OUT
Hi Katiethornton,
The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.
For more information, you can consult the following article:
You can uninstall the audio drivers and try to install the drivers updated from the Dell Web site.
a. Click Start and type in Device Manager in the start search and press ENTER.
b. expand the sound, video and game in Device Manager controllers
c. right-click on the audio device and click Properties
d. click on the driver tab, click on uninstall the drivers and click OK.
You can check the Dell support link to download the latest version of the audio drivers.
Drivers & downloads for XPS/Dimension 400/9150
Hope this information is useful.
-
USB ports not working and having an error code 19. New driver download does not help...
Hello
19 code means there is a driver conflict such as two devices attempt to use the same resources.
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-----------------------------------------------
Then lets refresh the USB stack
Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
all except the category itself - REBOOT - it refreshes the drive and battery USBThis KB shows XP how to and the method of Vista is identical
http://support.Microsoft.com/kb/310575USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
http://www.NirSoft.NET/utils/usb_devices_view.html
You would remove all instances of problem hubs and devices, then restart.
----------------------------------------------
If necessary try these two:
Tips for solving problems of USB devices - and a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGBHardware devices not detected or not working - Mr. Fixit
http://support.Microsoft.com/GP/hardware_device_problemsI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
Camcorder to one of the ports usb gives error code 43
Original title: when I try to connect my camcorder to one of my usb ports it gives me an error code 43? How can I solve this
I'm trying to connect my camcorder Panasonic HDC - HS250 HD for my dell inspiron with windows 7. It comes up with an error code 43? How can I connect my camcorder?Hello
1. don't you make changes on the computer before the show?
2 is the issue limited to camcorder Panasonic HDC - HS250 HD?Error code 43 is an error in Device Manager which means the following:Windows has stopped this device because it has reported problems. (Code 43)Method 1:
You can try the steps in the link and check.
Tips for solving problems of USB devices
http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
Method 2:
You can update the drivers for the device on the manufacturer's Web site.Updated a hardware driver that is not working properly
http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctlyReference links:
Install a USB device
http://Windows.Microsoft.com/en-us/Windows-Vista/install-a-USB-deviceGet help with Device Manager errors
http://Windows.Microsoft.com/en-us/Windows-Vista/get-help-with-Device-Manager-errors -
I have a Dell XPS 8500 that stop unexpectedly, saying: it is a mistake to data of the core or something like that. Now when I start it and enter my password it teeters between the screen and the display of password.
I ran a test that says: I have an error code 2000-01 42 which means that I have a hard drive failure. But what kind of Player do I expect and how can I install it? Also, how can I recover windows on and find the right drivers?
Any help is very appreciated! Thanks :)
Any 3.5 "SATA drive Office will work as a replacement.
If you do not prepare a set of recovery media for the system when invited you to the first boot, you will need to contact Dell to buy a set of recovery media now.
-
Ports USB 43 problem error code
On a port USB is not recognized. Error code 43. I have four USB Port on the laptop. Three on the left and right and the other on the back. All have failed to recognize the devices. I tried in vain to run the programe "Fix it." Operating system is Windows 7 Ultimate
Hi CosmosOmondi,
What is the number and the model of your laptop?
Windows has stopped this device because it has reported problems. (Code 43)
Method 1: Reinstall the USB (Universal Serial Bus) controllers.
First of all, please disconnect all USB devices and then perform the following steps:
(a) click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.
(b) in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".
(c) repeat step 2 to uninstall all items under 'USB Bus controllers'.
Then, restart your computer and windows will automatically reinstall all USB controllers.
Method 2: the motherboard\chipset to the latest driver update.Note: Please check with the manufacturer of motherboard\computer before you install the driver.
Method 3: You can see the steps mentioned in the link below
Tips-for-solving-problems-with-USB-devices
http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices(Article applies to Windows Vista, not valid for Windows 7)
Method 4: You can view the documentation for the hardware for more information about diagnosing the problem.
-
All USB Ports no longer works after that Windows 7 update error Code 52 Dell Inspiron
How repairing USB ports when they have all stopped working after updates. Error Code 52 Dell Inspiron 1720. Pilot not signing not recognized.
You can check the following registry key? :
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ (36FC9E60-C465-11CF-8056-444553540000)
Is there a 'name' UpperFilters and LowerFiltersin the registry for this key, in the right window?
If so, what is 'Data' for these names?
-
I get an error when I try to download apps from the store on my dell xps. It's on windows 8 and the error code is 0x8000706ba. I also have webroot anti-virus software.
Your welcome, come back if any problem happens!
Thank you.
-
XPS M1330 error Code 2000 - 0141
Hello
I use a Dell XPS M1330 like a laptop and main computer. I turn off night but work on it fairly regularly throughout the day. I was recently working on this subject, and he's locked. CTRL Alt Delete did nothing, so I had to do a hard restart. When it started, I got error code 2000-0141, does not not not my hard drive. BIOS not found anything. I off for maybe 15 minutes and then try again.
I can now boot windows... a little. I can either start normally or repair mode (recommended). I tried to fix the mode and he sat there on the screen for about 4 hours. I tried in normal mode, and it loads in continuous (1: 00, still no start with microsoft windows bar continuously flashes).
So now I lead nowhere, but the computer does not recognize the hard drive now. What is an overheating problem? What can I do? I'm working on my laptop, so I suffer serious withdrawl.
-Sim
-
problem: when I turned off the laptop, it restarts and the rotating fan to high speed, I diagnose test automatically. I found this error Msg: hard drive 0 - self test unsuccessful. Status: 79 Msg: error code 2000-0142 suggest me what should I do
The hard drive failed - you need a new portable player, 2.5 "SATA.
-
Studio XPS 8100 does not start
Hello! I have a 2010 studio xps 8100 (Intel (r) Core i7 CPU 860 to 2.80 GHz, 8 GB ram) and it's great when it works. Last week, I was out of town and when I came back it would not start upward. I can turn it on and start the fans, but it does not pass the POST and therefore does not start. I tested the ram and it seemed ok (two beeps when trying to boot without ram, no beeps when ram is correctly placed). The original of the graphics card died last year and I had it replaced with an EVGA Geforce GTX 750, I chose because it was one of the few cards that could work with the power supply 350w provided with your computer. I thought that maybe the PSU was then replaced by a 500w PSU, but the problem persists. I then read somewhere that if you SNYC date/time problems (which I was when the computer would turn on) that you need to replace the battery on the motherboard, so I did and still does not start. I don't know what I can do, is the dead motherboard? I tried the drain the power thing (release the button so that disconnected power for 30 seconds) and that didn't work either.
maddygillisYes, but I'm sure that the battery is not the issue. If it was I'd get stack codes error beep (5 beeps).Not necessarily...
maddygillisIt does not pass the POST because it does not start...If the video card is faulty, the PC can still start but you just do nothing appears on the monitor, so I don't know that you can actually say that it does not pass POST.
When you have tested the monitor with your laptop, did you use the same cable and video port on the monitor that you use with desktop? If you have used another port on the screen with the laptop with the office, this is not a fair test.
Have you tried reinstalling the video card into its slot and check the connections of the video cable at both ends?
This system has onboard video and Pluggable software component video card. So, you can remove the add-in card and switch the monitor to the onboard video port. According to the specifications, the onboard video has HDMI and DVI outputs, so assuming that your monitor supports either people, you have an easy way to test more.
NOTE: The embedded video ports are DISABLED unless you physically remove the video card. If you cannot move just the video cable to a built-in port while the video card is installed.
Maybe you are looking for
-
Satellite L775: No download 'BlueRay Player' after update for Windows 8
Hello Please help me... After upgrade from win 7 to win 8 it is not possible for playback of bluray on my Satellite L775.Where can I download the software for bluray playback? Under the following link, it says that Toshiba offers to install the TOSHI
-
iMac 5K with ultra wide screen LG
Hello I just ordered a 5K iMac and I currently have an LG monitor ultra wide 34UC87-C I had to connect to the Mac. My question is which compatible cable should I buy given the resolution 3440 x 1440 p of the external monitor. It is not a thunderbolt
-
USB\VID_138A &; PID_003F &; REV_0104
I need a free link to download this driver. It's about to drive me crazy. Thank you USB\VID_138A & PID_003F & REV_0104 Win 7 64 bit Laptop HP probook g1 640...
-
Hi, I'm having a lot of problems with my laptop HP G61 S.N. [personal information deleted]. Product; VY438EA #ABU. It is running Windows 7 and has an Intel Celeron processor. He started running very slowly and took ages to bring up the pages as web p
-
I use a Toshiba HDTV screen as my computer screen, and it is set at 1360 x 768 max resolution. I'm having a problem with playing some games because when the game starts, the screen beyond the Center and there is no options in the game that will allow