XPS M1330 error Code 2000 - 0141

Similar Questions

• had a blue screen with error Code 2000-0141 message no hard drive not detected.

  I ran AVG Free, but each line said file locked not run testedI repair microsoft and checking watch prblem is still windows update components need to be repaired

  Hi, Mike,.

  Run the following in default mode first and then go back and run it in aggressive Mode.  Before running the tool, go to a clean boot state.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Run in default Mode by using the Fixit from the link below.  Restart and retry Windows Update.  If not effective, run the Fixit in aggressive Mode.  New attempt to update when finished

  FixIt - How to reset Windows Update components

  http://support.Microsoft.com/kb/971058

  Don't forget to return to a normal startup when done.  Try searching for updates in normal mode.

  I hope this helps.

• No drive detected the 0141 error code 2000-0141 msg error code

  OK, we tried 'resettlement' the reader a couple of times but without success...

  And we carn can't actually test the drive on another computer laptop, so we are a bit stuck as computer repair shops can be expensive, but I have no choice to take there eventually, but for now, I'm just gain some knowledge on the subject

  My main concern, if the drive does not completely and permanently...

  That's what all the operating system, it was on a dell inspiron 1525 with a preinstalled operating system "vista ultimate".

  There is no backup of any type, I need some advice on this subject, because vista ultimate is pritty expensive and you really have to buy another copy of the operating system and install it on your new hard drive...

  After all, you've already paid for it...

  The laptops warranty has run out, so I guess there is no help from dell on this one there...

  Thanks for all your replies Chester/uk

  Ask their Dell recovery media.

  You cannot use a Toshiba Recovery disk on a Dell computer.

  And how could install Vista from a Windows 7 disc anyway!

  You can try this IF you know what you are doing:

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > find the latest Vista drivers for it > download/install the

  Good luck with it.

  Mick Murphy - Microsoft partner

• Diagnostic error code 2000-0123

  Unable to connect and then when I ran before initialization system assesment 4510 build got error code 2000-0123.  How to solve?

  Hello

  ·          What version of the operating system is installed on the computer?

  ·          What happens when you open a session?

  ·          When the issue started?

  If you are using a Dell computer, then check out the following link for the difficulty with the error code: 2000-0123.

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=DSN_300428&isLegacy=true#memory

• Error code: 2000-0146 (laptop hung on "Installation screen Windows updates")

  OK, so I have every time I turn on my computer dell laptop (I have windows vista) it acts like it is to install the updates of windows. He said same facility 3/3 even though the completion bar shows 0%. She does this, is like its about to restart then passes to the installation screen.  I ran the diagnostic test and the error code 2000-0146 came. I'm not sure if this is useful, but if anyone has a solution please help! Thank you

  Oh and I tried to restore the option and he did nothing.

  Hi cgardne5,
   
  1. How did you restore the computer?
   
  Try these steps and check the result.
  Step 1: The repair of the boot with Vista DVD
  a. Insert the Windows DVD.
  b. restart your computer.
  c. let the computer restart (boot) from the DVD.
  d. If you are prompted, press a key to continue.
  e. When you reach the screen install Windows, select your preferences in the language to install, time and currency format and keyboard or input method boxes, and then click Next.
  f. do not click install now. Instead, click on repair your computer. The System Recovery Options dialog box appears.
  g. make sure that the appropriate operating system is selected, and then click Next.
  h. After you click Next, the System Recovery Options menu appears.
  i. click on startup repair. Once the Startup Repair tool is completed, click Finish to restart the computer.
  j. remove the DVD and restart the computer to see if the system boots fine.
   
  See Repairs to the system of Windows recovery environment
  Step 2: If you do not have the Vista DVD, start the computer in safe mode and restore the computer
  See Start your computer in safe mode
  See System Restore
  NOTE: You can also choose the system restore on the system recovery options.
   
  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error code 2000-0146

  Hello

  I get the error code 2000-0146 found no operating system, I'm on Windows Vista on a Dell inspiron 1545.

  Tried to boot from the CD I can do a disk check but it go than even if loading step and then the green light flowing (as knight rider because..... kit) while he just sits on a gray screen... Any ideas anyone... youn think it's disk hard totally kaput, or maybe something else... I read on the site that someone changed its ram as 1 was defective and it worked.

  Thanks in advance

  Chris.

  Saving your files:

  You can remove the hard drive and put it in a hard drive USB enclosure > plug it into another computer > and try to read and copy your data in this way.

  @@@@@@@@@@@@@@@@@@@@

  This program may also interest you.

  "TestDisk, data recovery.

  http://www.CGSecurity.org/wiki/TestDisk

  TestDisk can run under

  • BACK (either real or Windows 9 x box BACK),
  • Windows (NT4, 2000, XP, 2003, Vista, 2008, Windows 7 (x 86 & x 64) Windows, 10)

  @@@@@@@@@@@@@@@@@@@@

  Or, you can download Knoppix > make a bootdisk to > start your system with it (IF your material is all work) > and copy your data from the hard drive like that.

  http://Knoppix.NET/

  "How to use Knoppix.

  http://Lifehacker.com/192982/geek-to-live--rescue-files-with-a-boot-CD

  @@@@@@@@@@@@@@@@@@@@

  "Recover files from Windows using Puppy Linux disks"

  https://www.WinHelp.us/recover-files-using-Puppy-Linux.html

  See you soon.

• ERROR CODE 2000 - 0142 WHAT DO I DO WITH THIS CODE?

  I have a laptop DELL with Windows Vista loaded.

  It tries to load the desktop but keeps running without result green bar

  CHECKDSK is conducted without all the mistakes are found.

  DIAGNOSIS showed the color screen, then the error code 2000-0142

  which seems to be related to the hard drive.

  F2 function key works to change settings

  What should I try to run windows?

  Thank you

  Hello

  It is an error code Dell saying that your drive hard has failed and must be replaced.

  Read this information from the Dell Community.

  http://en.community.Dell.com/support-forums/laptop/f/3518/p/19451299/20115134.aspx#20115134

  http://en.community.Dell.com/support-forums/disk-drives/f/3534/p/19498610/20329964.aspx

  http://en.community.Dell.com/support-forums/laptop/f/3518/p/19485947/20274290.aspx

  For more information about error codes Dell, please ask in the Dell Community Forums.

  http://en.community.Dell.com/support-forums/default.aspx

  See you soon.

• Error code 2000-0146 and 0F00:065 D and B 0F00:137

  I have a Dell Studio 1735 laptop.  Today it froze on me.  I could only make a hard stop.  I tried to log in again and got on the desktop with icons, but couldn't go further.  Don't have hard stop yet and I tried to go back to the top.  I made a kind of diagnostic tests and received the error code 2000-0146 following.  Also received the 0F00:065 D error reading DISK_0-self-test and 0F00:137 B DVDRW_1-disk is missing Virgin insert the data disc (example of the RCD).  I don't know what all these means.  Can someone direct me if it can be repaired and how I can fix it.  Or do I need a new hard drive.  Your help is greatly appreciated.  I use another laptop to write this message.

  The first two messages mean that the hard drive has failed. The third says there is no disc in the DVD drive, so it could not be tested.

• error code 2000-0123

  my friend has an inspiron she bought there is display the following error a year and a half

  Info: the configuration for an item in the object is invalid in the boot configuration data store.

  Hi Richard,

  1. are you able to boot into normal mode after receiving the error message?

  2. when the problem started?

  3. did you of recent changes on the system?

  You can consult the following link of Dell support for the difficulty with the error code: 2000-0123 and checkif it helps.

  Pre Boot System Assessment (PSA) Diagnostics and Error Codes for Dell computers

  Hope this information is useful.

• Operating system will not start and run - error codes 2000-142, 0F00:075 D, 41166486 uncorectable data error media wrtie block protect error code 0F00-0244

  I have dell 1525 top of the tower and OS will not run. Error code 2000-142, status bite 79, error code 0F00:075 D and Bios memory hard drive, SATA drive read your 41166486 data uncorectable media wrtie error block protect error code 0F00-0244then kept showing up on several more blocks.  Can I fix?  Joe

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Try to start the computer in safe mode and check if you can start the computer:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:
  Try to perform the verification and startup repair if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  It will be useful.

• Error code: 2000-0142, HDD 0-Self Test UN Succesful status 79.

  Hello guys

  I ran a Diagnostic Test on my new laptop N5010, it failed the Test of hard drive and gave this message "error Code: 2000-0142, HDD 0-Self Test unsuccessful status 79.»

  Can someone help please...

  Regarads
  

  khanisar

  Error Code 2000 - 0142, indicates a failing hard drive / failed and you need to replace it, because it is new laptop for a replacement of the hard disk, contact the Dell Technical Support and provide the error message.

  Bev.

• Dell Xps l502x error code

  problem: when I turned off the laptop, it restarts and the rotating fan to high speed, I diagnose test automatically. I found this error Msg: hard drive 0 - self test unsuccessful. Status: 79 Msg: error code 2000-0142 suggest me what should I do

  The hard drive failed - you need a new portable player, 2.5 "SATA.

• Drive hard error Code 2000 - 0142

  Inspiron 15 (3531, mid-2014)

  I tried boot diagnostic that the result has failed with the error code 2000-142.

  I have used a quick diagnostic race through dell online support site - it shows critical errors found

  for hardware failure then suggested for a replacement.

  Targeted both reading test SMART short self-test is broken.

  We hope to hear from you on your recommendations of experts on hardware issues.

  [Admin NOTE: maintain the label removed in accordance with the TOU strategy]  [Admin NOTE: deleted in accordance with the Express service code TOU strategy]

  Ryan Ibarreta - [Admin Note: personal information]

  Philippines

  Error code 2000-0142 usually indicates a failing hard drive / failed, first of all, try to remove and reinstall the hard drive, then re-run the diagnostic tests and see if you receive the same error.

  If the same error is received, the hard drive has failed, then you need to replace it.

  If you have a warranty from Dell, contact Dell Technical Support for a replacement hard drive.

  Bev.

• Received error BSOD, ran Diagnostics, got the error code 2000-0146, tried to boot from different HARD drive, got the same stop error message

  So my friend gave me his computer dell laptop. The thing would boot normally for a few days until he would give me a blue screen of death with the "UNMOUNTABLE_BOOT_VOLUME" message constantly to not even upward. I ran the diagnostics and got the error code 2000-0146. What I've read, this code error means that the HARD drive is bad and must be replaced. So, to make sure that it's the hard drive, tried to boot from an old hard drive, I got around the installation by USB and windows gave me the same stop error message. May - so that means it's a motherboard problem?

  No, it isn't - unless the operating system was installed on this drive AND the system in question, that it won't work as a bootable drive.

  Unplug the system, remove or disconnect the battery and hold the power for 30 seconds approximately.  Turn on and re-run the diagnostic tests - if the same error appears again, the drive is bad.  Replace it.

• Error code 2000-0145 on SSD

  I have a brand new DELL Optiplex 9010 AIO and had problems with the SSD (Adata 512 GB).
   
  The problem started with a blue screen of death (BSOD) in Windows 7. After that each new start results in a BSOD. I tried with a new installation, but it also results in a BSOD when installing. I've upgraded to the latest version of the bios A09. The hard drive Diagnostics returns the error code 2000-0145. Try the hard drive in the results on another computer in the same code error when you run the diagnostic tests. Execution of diagnosis with a new hard drive in the computer works well, but when you pass on the original SSD drive the same error recurs.
   
  What means error code 2000-0146 means? Any ideas?
   
  Thanks in advance,
   
  Bug

  2000-0145 has to do with a rotation test.  Dell actually had a stroke of genius to design a diagnosis that has identified problems hard spin-up and test the integrity of a player.  An SSD does not have an engine and cannot return a response appropriate for this part of the test, immediately throws an error.  It is not a standard for one SSD to answer with a bypass for a test like this, since it is an exclusive test.  Some SSD cannot report this error, while other models will be.

  I had to do a lot of digging for it and tried several SSD to see how this error code is displayed.  Again, he would have them all, but he has been consistent among all readers of specific models.  Was a huge headache 2 months & nightmare for me.  SSD so now I'll try other software, or other system to check the integrity of an SSD before calling the bad disk.  A unique model of SSD, this has produced on several readers was the OCZ Vertex SATA III 4.  Fact on all sizes we tested: 128, 256, 512.  Down them on a version customized with various diagnostic tools: discs had no problem.  Many are still in production several months after running the tests.