error in c:\windows\system32\nvsvc.dll lack of entry: nvsvcstar

Similar Questions

• Error in C:\Windows\system32\nvsvc.dll __Missing entry: nvsvcStart

  Starting Windows, the error message above is displayed.

  I tried the update of Windows and the DVD player, but the disc will not play DVD etc.

  Anyone know how I can fix this please?

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

  If the system restore does not work, do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not work, try to start in safe mode (repeatedly hit F8 key so that the start and go in safe mode with networking).  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator.

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well he comes complete with no corruption, it could not repair (if it has these post of corruption here or try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228.

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If it does not, then thanks for posting any repetitive error message in Event Viewer on startup (Start / Control Panel / administrative tools / Event Viewer).  Here's how to use Event Viewer: http://www.bleepingcomputer.com/forums/topic40108.html.

  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  Special attention to the DVD driver and get the most recent available even if it shows that it is already in good shape.  If you need to get pilots to leave the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows: http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows: http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  If this does not work, you will need to do a repair/system upgrade using the Windows Vista Installation disc authentic (you own or that you can borrow from someone).  Here is the procedure: http://www.vistax64.com/tutorials/88236-repair-install-vista.html as well as the upgrade from an earlier version of the Windows section of the following: http://support.microsoft.com/kb/918884.  Although this will not affect your data, settings or programs, you should always back up your data before you start just be on the safe side. If other procedures do not work, it is almost certain to work.  You can have a lot of updates to re - install (including all you need to remove service packs).  If the version on system with SP1 or SP2 preinstalled cane and the disc is an earlier version, then you will need to do a slipstream drive as follows: http://www.vistax64.com/tutorials/151606-vista-sp1-slipstream-installation-dvd.html.

  I hope one of these procedures can solve your problem.  If this isn't the case, after return and we will try something else.  Return message anyway so we know how it turns out.

  Good luck!

  Lorien - a - MCSE/MCSA/network + / A +.

• I get the rundll error "error loading C:\WINDOWS\system32\vcnflrd.dll the specified module is not found."

  I get the rundll error "error loading C:\WINDOWS\system32\vcnflrd.dll the specified module is not found."
  I have Windows XP Professional, I installed Windows 7 and windows 8 and windows defender and avast antivirus scan and complete.  I did a full cleaning.

  Thank you

  I get the rundll error "error loading C:\WINDOWS\system32\vcnflrd.dll the specified module is not found."
  I have Windows XP Professional, I installed Windows 7 and windows 8 and windows defender and avast antivirus scan and complete.  I did a full cleaning.

  Thank you

  Hello

  you are fully updated? This means that the module cannot be found, what you want to do when you get this error? error codes >?

  check the reports on the problems and solutions

  You can do a support ticket, follow the link

  http://support.Microsoft.com/common/international.aspx?RDPATH=DM;en-us; Select & Target = support

  Microsoft product support has some tools that will be useful and can help to find a solution

  have a great day with OneCare Scan + 50 tips Windows 7even infected with the center of privacy? DELETE this Blog search & response threat Sysinternals Live Tools + TRANSLATOR+ Photosynth + Microsoft Security + Microsoft SUPPORT + Of Live Labs PIVOT + Microsoft Live Labs + Office 2010 beta + get Windows LIVE!

• "Error loading C:\WINDOWS|system32\sshnas21.dll".

  This is the message that appears when I start my system "error loading C:\WINDOWS|system32\sshnas21.dll. The specified module could not be found. "What do I do?

  This is the message that appears when I start my system "error loading C:\WINDOWS|system32\sshnas21.dll. The specified module could not be found. "What do I do?

  Looking for errors like this by doing a search on Google for the name of the file.  Usually, they turn up without success.

  When a search in no hits or suspicious hits result, the answer is usually that the file in question is linked to the malicious software and your anti-malware application has deleted or quarantined file, but left to the Windows registry entry that tries to start the malicious software when you start your computer.

  See http://answers.microsoft.com/en-us/windows/forum/windows_7-files/error-of-sshnas21dll-missing-at-the-startup/c414c2a7-eb5c-4d67-9883-7817fb742d18 (ignore the parts specific to Windows 7)

  Download, install, update and run full scans with two of these free analytical tools:

  MalwareBytes AntiMalware
  SUPERAntiSpyware

  Do not run the scans at the same time.  They can take some time, so start an and then go for a non computer chore for awhile.

  If the scans does not solve the problem (and they can't, because the actual malware file has already been processed), then download and run Autoruns.  Click on the "Connection" tab and look in the column 'Image path' for the dll named in your error message.  If it is not displayed in the connection tab, click the "all" tab and use the file > search tool.  A characteristic of the search of Autoruns tool is that you must move the selection under the element line "found" before you "Find Next."

  Once you find the line with the file in question, either "delete" or (if you want to be safer) uncheck the box.  The latter prevents the line running, but you can reactivate it later by removing the check mark.

• Error loading c:windows\system32\sshnas.dll wants to say what and how do I clear this pop up?

  Error loading c:windows\system32\sshnas.dll wants to say what and how do I clear this pop up?

  Hello

  Step 1: sshnas.dll is a component of spyware or malware.  Online virus and malware scanner and check.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Step 2: You can also see the question in the clean boot state.

• error message; C:\Windows\System32/igfxres.dll

  Hi, I keep getting this error message c:\Windows/system32\igfxres.dll is not designed to run on windows or it contains an error.

  I am running windows vista Home premium. Can someone please help?

  The file belongs to your Intel video drivers. Install the latest version. Bring:

  1. site of the device mftr. ; OR
  2. site of the card mother mftr. If the material is on board; OR
  3. website of the OEM manufacturer for your specific machine if you have a PC OEM (HP, Dell, Sony, etc.).

  Read the installation instructions on the Web site where you get the drivers.

  To find out what hardware is in your computer:

  1. read all documentation that you got when you purchased the computer.
  2. If the computer is OEM, access the site Web of the OEM for your specific model machine and look at the specs (you'll be there to get the drivers anyway)
  3. download, install and run a program of inventory of the free system like Belarc Advisor or System Information for Windows.

  http://www.belarc.com/free_download.html - Belarc Advisor
  http://www.gtopala.com/ - System Information for Windows

  MS - MVP - Elephant Boy computers - don't panic!

• I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  Hello

  I googled this file pofusido.dll and it could be caused by a virus.

  I would suggest that you disable the restore mode as viruses use it to reinstall set apart them.

  Download and install the free http://www.malwarebytes.org/

  Restart the computer and keep pressing F8 to get into safe mode with network connection.

  Once you have updated Malwarebytes run and see if it can remove the virus.

  So delete all cookies in your internet Explorer.

  Please keep in mind that my answer is based on the information in your message. More the better I can answer, Slan go foill, Paul

• Error loading C:\WINDOWS\system32\shimgvw.dll

  Hello everyone,

  Recently, I received a very troublesome machine I have don't seem to not be able to solve. He began with thumbnails of Image not appearing is not in Windows Explorer.

  Since then, I have studied the issue widely and have not yet found a solution. Here is a list of the things I've tried:

  • Open a jpg image with 'Windows Picture and Fax Viewer' by using a right-click in Solution Explorer, and selecting 'Open with'. Result: "error loading C:\WINDOWS\system32\shimgvw.dll system cannot find the file specified."
  • Check the existence of shimgvw.dll and there are of course. When I opened a back and 'cd' command line to C:\Windows\system32, enter "regsvr32 shimgvw.dll", the result is: "failed to LoadLibrary ("shimgvw.dll") - the system cannot find the file specified."
  • Next test was run "sfc/scannow" as suggested in the many messages on several online forums. This command runs for a while and returns without error. Tried the above steps once again, same results.
  • So I uninstalled SP3 through the Add/Remove programs in Control Panel. Has raced for a while. SP3 renewed. Has raced for a while. Still not perceived image and still the same error messages.
  • Finally, I got a Windows XP SP3 slipstream CD, that I created a while back and ran a repair of the system. All is very well, and when finally the system rebooted, everything was the same old.

  I know that this may be easier to simply reinstall Windows XP Home fresh from scratch at this stage, but the user don't like this idea due to the loss of all applications, settings, etc.

  I would appreciate some guidance on how to solve this problem.

  Thank you!
  Wolfgang

  Since I have seen so many questions related shimgvw.dll on the web, that many people had not found a solution, I will post the solution I found. Thanks to some research more, I stumbled upon the Dependency Walker tool. http://www.DependencyWalker.com/ after the installation of this application, I was able to analyse fully what shimgvw.dll should be able to load all dependencies. Curiously, one of the DLLs it requires is gdiplus.dll, who, for some reason, in \windows\system32 but not exist inside a different application path I forgot now. Whatever it is, it should be noted that there is a 'properties' function in the Dependency Walker tool. Right-click the dll with red indicator and verify the path where a dll (in my case shimgvw.dll) tries to locate another dll file. I then just used the system32 gdiplus.dll and copied into the other lane and eventually I got with regsvr32 shimgvw.dll. Explorer then looked at thumbnails showing again and images and faxes were also back in business.

• Error loading C:\Windows\system32\cbsrSmng.dll

  At the start of my pc a message appears telling me "error loading C:\Windows\system32\cbsrSmng.dll" each time. I have an Aspire 6930 Vista system and this error has done this for over a year. I ran "sfc/scannow", and he says that couldn't be repaired. I have my original backup disk. Am now lost what to do.

  Hello

  To remove the error message if still there after the controls above to malware.

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Autoruns - free - see what programs are configured so that it starts automatically when
  your system boots and you connect. Autoruns also shows you the complete list of the registry
  and where applications can configure Auto-start for the files settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• When Vista starts, getting the error "Error loading C:\Windows\system32\sshnas.dll this module specific point is not found"

  When I start my PC it opens as soon as my desktop appears on the screen, error loading C:\Windows\system32\sshnas.dll the specified module could not be found.  How can I fix it?
  * original title - need HELP, Windows System 32 error *.

  Hello

  who is / was malware or a boot remains for her entry

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If the error persists after scanning use this program to out startup

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• When I go to install Silverlight, I get an error message C:\Windows\system32\samcli.dll error message.

  samcli.dll

  I try to use Netflix... It worked last night and when I went to play today it asked me to install Silverlight... when I go to install Silverlight, I get an error message C:\Windows\system32\samcli.dll error message. I tried to uninstall Silverlight and reinstall it using Revo Uninstaller Pro and still, I get the same error message. You can provide any help would be greatly appreciated.

  Thank you

  Lisa

  samcli.dll is associated with Security Accounts Manager Client and not with Silverlight.

  Download this dll from here: -.

  http://www.dllme.com/dll/files/samcli_dll.html

  Now, replace the dll file that is corrupted with the dll file you downloaded here: -.

  C:\Windows\System32

  [Note: it is a hidden file, so you must enable Show hidden... files]

  [Organize--->---> the folder options view and search]

• How to solve the error due to windows system32 mfc42u.dll

  How to fix error in windows vista x 64 in the windows system32 mfc42u.dll file?

  You don't say what effect this has on your system.  You try to install or to upgrade to Windows?  When the message appears?  Help us out with some details, please.

  The dll may itself be damaged so try using the repair system file checker.  Click Start, type "cmd" in the search/Run box and right-click on the CMD icon at the top of the results pane.  Select run as administrator.  When the cmd window type "sfc/scannow" at the prompt and press ENTER.  When the scan is finished, close the cmd window.

  If it comes from occurring during normal operation, you must use the system repair and recovery forum in the

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system?page=1&tab=all

  This forum is for the Windows installation.

• The bad image error. C:\Windows\system32\cfgmgr32.dll is not designed to run on windows or it contains an error.

  Whenever I try to install the material using a USB port, I get an error from the bad image. It is said:
  C:\Windows\system32\cfgmgr32.dll is not designed to run on windows or it contains an error.

  Any help will be useful.

  Thank you
  Jeff F.

  Hi Jfog18

   

  1. what material are you trying to install?

  2 have you installed for the device that you connect software?

  3. were you able to connect the hardware device much earlier?

  
  Method 1:

  You can analyze your computer using online for computer viruses antivirus scan. Rerailway to the link below to complete the virus scan online. Check if this help -
  http://OneCare.live.com/site/en-us/default.htm

   

  Method 2:

  You can perform a SFC scan and check if the problem is resolved.
  To Perform a Scan SFC -
  a. click Start, click programs, on Accessoriesprincipally made, right click guestand then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on Allow.
  b. type the following command and press ENTER:
  sfc/scannow
  A message appears indicating that "the system scan will start. Be patient because the scan can take some time.
  c. If all files require a SFC replace will replace them. You may be asked to insert your Win7 DVD for this process to continue.
  d. If everything is correct you should, after the scan, see the following message "resource protection Windows not found any breach of integrity".
  e. once the scan is finished, close the command prompt window, restart the computer and check.

  Check the link below for further guidance on scan SFC - mentioned
  http://support.Microsoft.com/kb/929833

  I hope this helps.

• How to fix RunDLL error message: C\window\system32\sshnas21.dll

  When my system I noticed a pop message "load error: C\window\system32\sshnas21.dll" on my screen. Please help me solve this problem. Is it because my system has a virus .please help.

  Hello

  Yes

  It is malware

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If this does not work in normal mode only the above work in SafeMode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  and if the problem persists you may need to remove it from the startup procedure

  try this program for that

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configureAutoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more. Autoruns goes way beyond the MSConfig utility bundled with Windows Me and XP.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• Error message "c:\windows\system32\atiumdag.dll is not designed to run on windows or it contains an error" appears randomly

  Original title:

  The title above guard poop upward on my screen, I don't know what to do about it. in the box it says also "c:\windows\system32\atiumdag.dll is not designed to run on windows or it contains an error. Try to install the program by using the original installation medi or contact your system admisistrator or the provider of software for support. .... BUT I do not understand what is the program and everything I try to repair by ATI shows nothing abnormal. HELPPPPPP!

  Hello Deborah,.

  I suggest you perform a System File Checker analyzes your computer and check for the issue.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833