Error "this computer does not meet the minimum requirements for installing the software" when you try to install Intel_ME_Driver.

Similar Questions

• This computer does not meet the minimum requirements for installing the software

  Hello

  I try to install the graphics driver on my laptop Dell Inspiron N5010 (I tried this three R252283, R257270 and R285472). But every time I get the error indicating that "this computer does not meet the minimum requirements for installing the software.

  Here are the details of my laptop configuration:

  Core i3 processor, RAM 3 GB, windows 7 64-bit Operating system

  Makes sense, you do not have the integrated Intel graphics card, but rather have an AMD graphics card, install it:

  http://ftp.Dell.com/video/R272410.exe

• This computer does not meet the minimum requirements... when installing graphics Intel HD 4000 for my Dell Vostro 5560 with Windows 7 64 bit

  In recent days, I reinstall Windows 7 to my Dell Vostro 5560 and this laptop does not have a driver CD, I downloaded all the required drivers for my laptop directly from the Dell Support Web site. I started to install a step by step. Chipsets, Audio, network, MEI, etc... However, once I try to install graphics, this laptop comes with 2 graphics card, an Intel and another is Nvidia. So, I try to install first Intel. When I click on the exe file, a message box appears saying that «this computer does not meet the minimum requirements...» ». Why is - what happened? I'm sure that my laptop include Intel graphics. Please help me as soon as POSSIBLE. I want to install Windows 7.

  Some drivers of today require at least Microsoft .NET Framework 4.5. Is this possible?

  It is certainly. AMD demanded 4 .NET. x + for their installer drivers for several years already, but I think they have started including with their driver downloads recently.

  -I never noticed if Nvidia use .NET with their drivers Installer, install but .NET 4.5.

  Download Microsoft .NET Framework 4.5 of the official Microsoft Download Center

  .

• Error installing Microsoft NET Framework 3.5 Service Pack 1 Setup program has detected that this computer does not meet the requirements to install this software

  I need to install Microsoft NET Framework 3.5 Service Pack 1, as it is necessary to perform a Dell diagnostic Test, but I've been advised that: Setup has detected that this computer does not meet the requirements to install this software. Requirement: Windows install 3.1.

  However, when I look at the download page of Windows Installer 3.1 is not actually as for XP with SP3. I tried anyway and: Setup has determined that the version of Service Pack for this system is newer than the update you are applying. There is no need to install this update. Well actually it is there...

  Is there a way to get around this?

  See below articles for solution

  1 system requirements for the .net framework

  http://msdn.Microsoft.com/library/8z6watww.aspx

  2 download links for .net framework

  http://www.Microsoft.com/net/download

  or

  http://msdn.Microsoft.com/en-us/library/5a4x27ek

  3. top 8 resources for .net framework

  http://www.Microsoft.com/net/itprofessionals

  4 dependencies and Versions of .NET framework

  http://msdn.Microsoft.com/library/bb822049.aspx

  5 frequently asked questions
  http://msdn2.Microsoft.com/en-us/netframework/aa497323.aspx

  6. management of versions, compatibility and run side-by-side in the .NET Framework
  http://msdn2.Microsoft.com/en-us/netframework/aa497340.aspx

  Good luck

• The settings saved on this computer does not meet the requirements for the network

  My old laptop connects fine but my other not.  When I go to connect to the network, it says "the settings saved on this computer does not match the requirements for the network."

  Hello Tazdmx83,

  Thanks for posting on Microsoft answers Community Forums.

  This problem usually occurs on wireless network connections. I suggest that you turn off any wireless security feature by following the steps below.

  1. click on start and control access panel.

  2. double-click on network connections

  3. right click on the wireless adapter and select Properties.

  4. Select wireless networks, click the name of your wireless network and choose Properties.

  5. in network authentication, select open to disable wireless security.

  6. Please try to connect.

  If the problem persists, I suggest that you remove the connection and re-create the wireless network connections. The following Web site can help you on the creation of the wireless connection.

  http://windowshelp.Microsoft.com/Windows/en-us/help/297fa2dc-B20B-4327-B673-707a968c86801033.mspx

  Important note: Microsoft provides third-party contact information to help you find technical support. These details may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.

  If the problem persists, I suggest you reinstall the driver of card wireless network and Re-create the connection.

  Remove the driver for the card
  ========================

  1. click on start. In the start search box type "devmgmt.msc", and then press ENTER.
  2. expand "Network adapters", double-click the entry for the wireless network device.
  3. click on the "Driver" tab, click "Uninstall".
  4. click on start. In the start search box type "appwiz.cpl", and then press ENTER.
  5 remove the entries related to the wireless network adapter.

  Reinstall the driver with your CD of drivers on the manufacturer's Web site. After installation, create the connection.

  Also access the link and try to follow the steps in troubleshooting network related issues on Vista-based computer:

  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  It will be useful.

  Thank you and best regards,

  Srinivas

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think

• ColdFusion Launcher does not accept the password when you try to change the web server

  I know this will sound stupid as wrong password is a password wrong, right? Well I swear I know my passwords and it's not having it.

  I am running coldfusion 9 and I want to change the default internal server that I put it to the top with the installation on apache server that ships with mac OS x. So I started the coldfusion launcher and clicked the button Web server connection utility to set up, he asks a password to continue, but usually accept it... I tried both of the passwords that I use for stuff course where I was confused which it requested one, but is not having either.

  I tried to change the password for the coldfusion administrator and still no joy. I know that sounds stupid, but I do not understand... How can I get if she does not accept my admin password... I have tried uninstall and try again once like stuff as it is a nightmare to get rid of my experience... always leaves a file somewhere that you can never seem to isolate who mucks upward following installation so I left it for the moment. Anyone got any ideas?

  OK, you cannot double-click the wsconfig file, cause, then you are not running it as sudo, so you will not be allowed.  'sudo' is 'Super user' and allows you to run a program, temporarily, as a super user.  If you do that you won't have permission to edit the httpd config file.

  Try the following.

  Launch the Terminal

  type: cd/Applications/ColdFusion9/runtime/lib (change the correct path if it is not the path to your ColdFusion)

  Press enter

  type: sudo java-jar wsconfig.jar

  Press enter

  It should ask you for your password. Enter it and press ENTER again.

  It should launch the configuration tool, this time with the appropriate permissions to modify the file httd.conf.

  Good luck

• Intel HD graphics driver installation error: "computer does not meet the minimum requirements.

  Hello

  I tried to update the Intel graphics driver in my notebook using sp55098.exe , but the system returned the following error:

  "This computer does not have the minimum requirements for installing the software.

  I have the following: dv6-6b05tx laptop computer running windows 7 pro 64

  It's the device I am trying to update:

  Intel HD Graphics Family
  Current driver date: May 7, 2011
  Current version of the driver: 8.830.6.3000

  I tried the drivers on the Intel site, but they do not work either.

  Help, please.

  Thank you very much.

  PS

  I managed to update the drivers of AMD Radeon HD 6700M using this link of guru3d.com.

  But I can't find a similar solution for the Intel card.

  Hello:

  Please read the notes on the AMD driver file...

  Description:

  This package provides the AMD graphics driver high definition (HD) and Catalyst Control Center for models of laptop computers that are running an operating system supported. For laptops equipped with switchable graphics modes, this package contains the drivers for the two graphics (GPU). Switchable graphics allow users to switch between a graphical power mode (normally used under the power of the battery) and a mode of graphics performance. If the video output high-definition multimedia interface (HDMI) is supported, this package also installs the HDMI Audio Driver.

  The Intel driver is only for the models with only the Intel UMA graphics adapter.

  You must live with what version of the video, Intel is in the AMD driver package.

  Paul

• OSX EL CAPITAN UPDATE CANNOT BE INSTALLED TO THIS DISK. THIS VOLUME DOES NOT MEET THE CONDITIONS FOR THIS UPDATE

  Hi all

  My iMac features are:

  • 27-inch, late 2013
  • 3.2 GHz Intel Core i5 processor
  • 8 GB 1600 MHz DDR3 memory
  • Start drive Macintosh HD
  • NVIDIA GeForce GT 1024Mo of 755M graphics
  • Storage: 301,35 free GB of 999,35 GB

  Running currently on OS X El Capitan with Update Version 10.11.3 installed January 27, 2016

  Problem: I was on the purchase of 2016 Office for Mac and tried to install the update of El Capitan OS X 10.11.1 which is necessary to solve the problems with this version of Microsoft Office.  During installation, the following error message appears:

  "OS X El Capitan update cannot be installed on this drive. This volume does not meet the conditions required for this update".

  I would be very happy if someone can help me in installing this update.

  Thank you.

  Slpm6

  I just got a quick reply saying 'You are not allowed to create or update this content'. What should I do to solve the problem? Thank you.

  You are using a newer version of El Capitan that the updater contains and so cannot install it.

  (139598)

• I bought ligtroom 5 06/09/2014, and then installed on my computer. This computer does not like it, I wish therefore installed lihtgroom on my new computer, but it's not market!

  I bought ligtroom 5 06/09/2014, and then installed on my computer. This computer does not like it, I wish therefore installed lihtgroom on my new computer, but it's not market!

  the error message is: "the signature of download package (3) exe, is damaged or is not valid" thanks for your help.

  Hi philippeb41403529,

  Please use the link below to download a fresh installation for LR 5:

  Install Photoshop Lightroom

  See also, How to download, install and activate Adobe applications

  Let us know if that helps.

• Computer will not use the drive when you restart.

  I have a Pavilion dv 9000 and had problems more and more lately (win explorer fails, application launcher fail, blue screens, crashes etc.).

  I decided to use the recovery disk that was created at first boot. According to all the manuals that I found (on - and offline), it is just to put the recovery disk in the DVD-ROM and restart.

  The problem is that nothing happens. The computer does not use the disk when it reboots.

  Anyone experienced the same problem with the recovery disk?

  I'm not having any other problems with the ROM, works perfektly once Windows is running.

  Thank you

  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error "this Setup does not support the target platform.

  I need solve the problem 'this Setup does not support the target platform' Please help me :'(

  See these two sites:

  http://forums.Comodo.com/install-Setup-configuration-help-CIS/this-installation-does-not-support-the-target-platform-t59001.0.html

  http://forums.Comodo.com/install-Setup-configuration-help-CIS/firewall-wont-install-this-installation-does-not-support-the-target-platform-t61629.0.html;msg434058

  Comodo is apparently the problem.

• I get an error, "the executable file that this service is configured to run does not implement the service" when I try to synchronize the time in Windows XP.

  After trying to fix the error of time synchronization by typing net start w32time that receipt of the message in the title.  In addition, type net stop w32time responded that the service was not working.

  Original title: the executable that this service is configured to run does not implement the service

  After checking the configuration in the registry and check or update if necessary from the link below:

  Then the time errors that I got from the command prompt window:
  Order--> net stop w32time & net start w32time
  Response--> The Windows Time service is not started.

  Order--> net start w32time
  Response--> system error 1083.
  The executable program that this service is configured to run in does not implement the service.

  --> Command w32tm/Resync /rediscover
  Response--> sending command to local computer resync...
  The following error occurred: the RPC server is unavailbale. (0x800706BA)

  Hi Mitchell_G,

  Thank you for keeping us posted.

  The steps of items offered in the previous post?

  We know if you need help. We will be happy to help you.

  Thank you.

• Why my computer does not recognize the CD when inserted?

  I am trying to install a software on CD, but the computer does not recognize it.  I tried even my audio CD but they is also not recognize it.

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• Error: "Windows could not complete the format" when you try to write to blank DVDs

  I get this error when you try to copy files to a blank DVD.  I am trying to drag and drop files into the dvd player and after a small roar, the dvd ram drive stops and the error message.  Then the drive no longer recognizes blank dvd inside.  I am running Vista 32 bit and my dvd ram is a matshita dvd - ram uj880as ata.  I tried to switch to the microsoft 'FixIt' site, but the problem is not resolved.  I think that the report mentioned that the reader could recognize not writable or something to that extent.  The player can play DVDs fine, however.  Is there a solution to this problem by replacing the dvd ram drive?

  Hello

  Have you tried to close all programs and then insert the disc to see what is happening? Try a slower
  speed or mastered format. Have you added any burning new software lately - these tend to compete
  for resources and can interfere with each other.

  Should which CD or DVD format I use?
  http://Windows.Microsoft.com/en-us/Windows-Vista/which-CD-or-DVD-format-should-I-use

  ====================================

  You have disk problem as the CD/DVD is actually 4 discs in 1 case (burn CD & DVD and CD and DVD read).
  Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  CD have a tolerance + - and you can write on the outside edge.

  Several good info here:
  http://Club.myce.com/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  -----------------------------------------------------------------------

  Try this troubleshooting:

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Unable to connect to the Internet, error: this computer does not have a network adapter installed and configured

  Original title: basic computer.

  I have a Dell with windows vista. He has been in place and slow so I reinstalled the program. Now I can't access the internet. I get an error message that says that this computer has a network card installed and configured. I have a linskeys wireless router and we have two laptops that work very well. Don't know what else to do.

  Hello

  Go to the Dell website and download the drivers for your model computer.

  http://www.Dell.com/support/drivers/us/en/19/DriversHome/NeedProductSelection?FKEY=Drivers_PS

  Use one of your other machines > download and save the drivers, network adapter, etc > copy of Flash Drive > transfer and install them.

  See you soon.