Errors of certificate RV042 browser by connecting to the web-based GUI

Similar Questions

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• WRT54G V8 cannot connect to the web-based configuration page?

  Earlier, I reset my router and was able to use 192.168.1.1 to visit the configuration page based on the web while trying to restore a home network, now that I have a new computer using Windows 7 that can not use the easylink advisor. I was able to get on the page update my SSID and WEP key. But when my wireless devices were still having problems to you connect to the internet, I tried to go back to the page and found that I can't seem to connect, even if my office is able to connect to other websites very well.

  Anyone know what I can do wrong? I use Verizon DSL. I was able to ping to the router and all tests have shown that it was connected fine, but I still can't get on the configuration page and my laptop can't connect to the network. I tried to reset the router again and still nothing. And Yes, I went through several cycles of power. I have also tried to move if the network card on my computer, but the computer said it was impossible to create a card for him, although at the time I had listed as a home network.

  Wireless on 192.168.1.1 connections often fail.  Using the router configuration pages, always use a computer that is connected to the WRT54G.

  If the above does not solve your problem, so here are my other tips to see the router configuration pages:

  You don't need an Internet connection. 'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  Point your browser to 192.168.1.1, and then connect to your router. Your username must be left blank. Your password is "admin" (without the quotes), unless you changed it.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  Some Zone Alarm users reported that the addition of 192.168.1.1 to their address list "of trust" solved the problem. This trick can also work with other firewalls.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. A report with this problem and also specify the brand and exact model of your modem (not router) number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system.  The router should work, but you will need to configure your router again from scratch.  If you have saved a router configuration file, DO NOT use it.

  If you still have problems, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• OATS: Error Message 'Unable to get a connection from the browser' on the record

  Hello
  
  I am involved in the control of the operation for application Siebel 8.1, with the OATS 9.3 tool.
  
  Trying to save, an Error Message * "unable to get a connection from the browser. You want to continue to wait for the browser load? "* appears, even if InstallBrowserHelpers has been installed.
  I tried to uninstall the 'BrowserHelpers' and re - install but the question remains.
  
  your response on this will be appreciated.
  
  Thank you!

  Try to uninstall everything that touches on OATS to your PC then re - install. Uninstall steps are in this forum. You can search for it. Work around the error can take a long time.

  Concerning
  CP

• Server connection error:-1 there is a problem connecting to the server... hp photosmart 5510

  HP photosmart 5510 e - while a printer B111a

  Windows vista 32-bit

  connection error message-Server error:-1 there was a problem connecting to the server, press Retry or ok to continue

  No changes have been made to my operating system

  Try to add new applications with eprint center of my Compaq Presario CQ60 laptop to my HP printer. Computer tells me that the new applications are there and ready to use, but printer says 'server connection error "? I followed all the instructions to connect to the wireless router, but I'm not sure how to connect to the "Server"?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

  Let me know if you have any additional questions. Thank you!

• Get 810 error message when you try to connect to the VPN using L2TP protocol

  Original title: L2TP will not let me connect.

  I am in Workstation 9 and in each virtual machine, I have an AD - DC (2K8R2Enterprise), CA and RRAS (2K8R2Enterprise) and my last vm is a win7 (they are all tests).  All are not updated, but the PPTP, IKEv2 work without problem.  The second server that has the CAs and RRAS is a member of the AD - DC server.  The Win7 is not on the domain and I have Win7 a client certificate.  I have ensured that the CA root of trust is in the user store and computer Trusted Root CA.  I have also ensured that the Win7 client certificate is in the user store and personal computer.  I get a 810 error message when I try to connect to the VPN using the L2TP protocol.  I have exhaustively studied this problem and I can't find a solution to this problem.  I also raise the functional level of the domain to 2K8R2.

  I think this should be a simple and easy solution, but where can I find the answer?
  Please help me.
  Thank you for your time.
  Allan.

  Hi Allan,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

  If you need any other assistance, let know us and we would be happy to help you.

• I can't spend 6 s iphone to 9.3, get error message that I am not connected to the internet.

  I can't move my 6s iPhone to ios 9.3. My phone currently has ios 9.2.1.  I get an error message that I am not connected to the internet during the update tries to go through the verification step. I checked that I am connected to the internet. I turned my phone off and tried again but same error message

  Hi - I'd wait to make the update you will see elsewhere in these issues forums with hyperlinks in mail, messages, and Safari does not. I wish I had waited...

• My without wire is connected, but nothing of my browser reopens it displays the web page is not available

  My dell laptop shows that it is connected but nothing of my browser opens, it displays the web page is unavailable pls help me to solve this problem

  Hi shaikh_941,

  1. what brand & model of network card?

  2. were you able to use the wireless network connection before?

  3. are you able to use the wired connection on your computer?

  You can follow these links and check if it helps.

  In the Windows wireless network connection problems

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  For Internet Explorer, you can follow this link & check if it helps.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  Hope the helps of information.
  Please post back and we do know.

• T400: Error Message - there was a problem connecting to the TPM secure

  Hello

  I am a new user of ThinkPad. I just got my T400 a week ago, and I'm a fan of him immediately. But there's this little thing that really bothers me. The second day I used my laptop, I got this error message: "There was a problem connecting to the module of TPM (safety device) on this computer", and I got this message since that date, every time I turn on my laptop.  What it means? And how do I get rid of this error message? Thank you!

  Moderator Note: Type + error message added to the line object for clarity.

  go into the bios and check if the TPM secure is enabled or disabled in the BIOS. Make sure it's on. If the problem persists then call Lenovo, could be a hardware problem.

• error code (-3212) itunes could not connect to the store, make sure your network connection is active and try again. Can someone please tell me how to proceed? __

  error code (-3212) itunes could not connect to the store, make sure your network connection is active and try again. Can someone tell me please how to do this?

  Hi vivasiousv,

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  See the links in the Apple Web site and try the steps mentioned below.

  http://discussions.Apple.com/message.jspa?MessageID=6096760

  http://discussions.Apple.com/message.jspa?MessageID=8436848

  For additional support post your query in the Apple discussion.

  http://discussions.Apple.com/category.jspa?categoryID=150

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error found: iP1600 printer can be connected to the network

  Title: Problem of networking; model of the host is running XP and can not print from computer laptop/WIN 7

  Hi, my host comp. is running WIN XP and laptop WIN 7. I've already updated the printer driver Canon witch is connected to the host model. On the hardware of the laptop I can see the printer is on a network, but... cannot print the test page / troubleshooting of the error found: iP1600 printer can be connected to the network.

  I also downloaded on laptop CanonPrinter add-on driver, this driver necessary?

  Hello

  I suggest you install the drivers for PIXMA iP1600 on both Windows XP computer and check if the problem persists.
  PIXMA iP1600
  http://www.USA.Canon.com/Cusa/support/consumer/printers_multifunction/pixma_ip_series/pixma_ip1600#DriversAndSoftware
  Hope this information helps.

• Update Adobe CC reaches 5% installation point and error reads as follows: "try to connect to the server...". »

  Update Adobe CC reaches 5% installation point and error reads as follows: "try to connect to the server...". »

  Thank you in advance for your response guys.

  Hi yusney,

  Please check the help below document:

  https://helpx.Adobe.com/creative-cloud/KB/Error_Code_2_failed_update.html

  Kind regards

  Sheena

• I searched for a solution for the problem I was on Win 7 Pro Service Pack 1 in the links on an open Adobe Acrobat file will not open in my browser Firefox 33.0.2. The error I get is "Acrobat could not run the web browser.  Unknown error. (123).

  I want a solution for the problem I was on Win 7 Pro Service Pack 1 in the links on an open Adobe Acrobat Pro 10.1.12 file will not open in my browser Firefox 33.0.2. The error I get is "Acrobat could not run the web browser.  Unknown error. (123).

  You can try a repair of your Acrobat installation. Maybe, at least it's a start toward a solution.

• I can't create a new site of catalyst for business with Dreamweaver CC 2014. The error message states that Dreamweaver cannot connect with the server, try again later. How can I solve this problem?

  I can't create a new site of Business Catalyst with Dreamweaver CC 2014 (Mac). The error message states that Dreamweaver cannot connect with the server, try again later. In addition, I am also unable to load remote site Business Catalyst created previously as it says that there is something wrong with my user name or password. However when I put my password and press to test the connection, he said that it has connected successfully. What is wrong and how can I solve this problem?

  Thank you

  Thanks for the reply, however it seems to work again after I removed some unused Dreamweaver sites in the section "manage sites" in Dreamweaver.  It may have been a conflict of name or something.

  Concerning

  Adrian

• How can I disable the CS3 when I get an error message that I am not connected to the internet when I am?

  Try to deactivate CS3 from a computer to reload on another. Get the error message that I am not connected to the internet.

  It is NOT correct. Customer support can handle deactivations of CS3. Use Web Chat here:

  Serial number and activation support