ESXi cannot ping uplink gateway

Similar Questions

• CSR 1000v for Vmware Esxi, cannot ping / output

  Hello

  I just installed file eggs a 1000V CSR in my personal laboratory in an ESXi.

  I followed this link:

  http://www.fryguy.NET/2013/12/27/Cisco-csr1000v-for-Home-Labs/

  I have a 1 Giga interface in the vlan by default with the VMXNET3 adapter type as suggested.

  Whenever I turn on the CSR I have configure the interface and I unshut it. Negotiation is automatic (I tried to link hard but without success).

  Problem is that since my pc I can not ping the CSR giga1 interface and vice versa. But on both sides, I see the arp of the interface.

  I tried to change the type of adapter on vmware (VMXNET2 or E1000) but without any help...

  If I turn on a debian or Windows VM on the same network card on the same vlan I can ping or reach it.

  I tried to debug the ip packets, but nothing shows up some questions.

  Config is a default one... there no ACL, not security features, nothing... just an ip address on the giga1 and the no command closed.

  What is there?

  Thanks in advance

  Hello

  Can say you that it was really the problem.

  I have ESXi 5.5.0 3116895 and I installed CRS1000V 3.17 and it works perfectly

  Good bye

• Install the new - cannot ping configured gateway or DNS servers

  Hi all

  My old VMWare ESXi 3.5 OS got corrupted I did a fresh install of VMWare ESXi 4. It installed ok and I was able to configure everything successfully, but when I run the network test it is impossible to ping anything whatsoever, but it's own IP address.

  I have another machine on the same subnet with the same exact configuration (except for the hostname and IP static) settings and it works properly without any problem.

  I already checked the cable at the back and the green light is on and the flashing. I tried to restart the machine after having placed in the configuration information and settings remained at what I put in, but I still get the same result. The network test is a failure.

  Does anyone have any suggestions as to what could be the cause of this?

  How do you have installed and configured network adapters?  Have you tried swapping the cables between network cards?

  Also, do you have the trunks VLAN configured on the switch?  It is possible, that you must specify a trunk VLAN for the management network to do the work.  That would probably have already been configured on your host 3.5 but is not automatically detected and added.

• VM management host cannot ping gateway or switch

  Hello

  
  We have a server Esx 5.0 with 3 vm on it. When I try to ping the management network of vm for my pc that I do not get an answer too trying to ping from the vmn console I can not ping to the gateway, but I can ping dns. However, I can rdp in vm servers and the ping to the gateway of each server, as well as newspapers in vsphere. We have a system with 2 voip VLAN, the other data and another for voice. Hosts and servers are all on the same cisco switch.

  VM management network

  IP - 192.168.1.6

  Sub - 255.255.255.0

  GW - 192.168.1.1

  DNS - 192.168.1.10

  Cisco switch - 192.168.1.3

  Data Vlan - 192.168.1.1

  Firewall - 192.168.1.2

  PC

  -cannot ping 192.168.1.6

  -can ping everything else

  From the console network management

  -cannot ping 192.168.1.1 a.3 or any pc

  -can ping 192.168.1.10

  It sounds like a switch problem but do not know how to fix it. The switch is a switch of cisco small business pro 8 ports

  Make sure that your routing has L3 to a defined network to get traffic to your host (192.168.1.0/24) network to any network it seeks to achieve. You did not show what the subnet for the PCs are so I'm not sure that the network is.

  Regarding the gateway ping, make sure that the echo ICMP message is enabled by the firewall so that ping responses can go to the host. If you still cannot ping the gateway with that on, there may be a larger problem with your connectivity.

• DLR Uplink and GSS internal transit same VXLAN cannot ping each other.

  Start with, I run NSX 6.2.2 firewall rules on 'allow all' to 'all' to 'all' "all protocols", in other words disabled...

  I have a VXLAN 5000 transit, with an uplink DLR interface attached to it, and an internal interface GSS in the appendix in which neither of the parties can ping to another. So for troubleshooting, I added 2 VM Windows attached to the same transit VXLAN 5000, a virtual machine is on ESXi host 1 and the other is on host ESXi 4. They can fine ping each other, and two virtual machines can ping both the uplink of DLR and internal interfaces of the GSS.

  This question has puzzled me because it makes no sense, why the DLR and the GSS cannot ping each other but 2 virtual machines that VXLAN can ping all adjacent devices. I can even put bridges on those virtual machines with a rule NAT on the GSS and those virtual machines can get internet through the GSS, but no matter what I try, the DLR cannot ping the GSS, and the GSS cannot ping DLR...

  I need to define a static route between the GSS DLR <>- but if I can't even answer ping interfaces I'm dead in the water.

  If I install virtual machines in a network LAN DLR interface such as WebApp and test for example database, I can ping throughout the DLR together until the IP DLR Uplink, but then he cannot ping the GSS internal.

  Does anyone have suggestions for troubleshooting? Test commands that I can run? I tried many things and then lots of websites with the troubleshooting steps. Everything seems fine, all green checks in the installation steps... All roads, MACs, ARP tables appear as expected when I run test on host computers commands and controllers. I don't know what is the cause except for a bug in the code...

  All ideas are welcome... Thank you

  UPDATE:

  Yes, so it has need of a static NAT rule on the GSS...

  In my environment, I added a SNAT rule on adapter: ESG_Uplink with 0.0.0.0/24 CBC-translation dst: 1.1.1.101 (my lab ESG IP Uplink).

  It works now... VM tenant box connected to WebApp portgroup (192.168.13.115) can now ping gateway DLR, through routing OSPF to the GSS and ping on physical bridge of...

  I learned a lot on this one... I'm not going to worry about why the static route, I tried first post didn't work, since I was the OSPF running instead (which is more appropriate for my laboratory for realistic scenario anyway), and the Foundation will now suffice to build the rest of this POC vRA / vRO lab...

  Thank you in any case, sometimes it's just nice to have someone to listen.

• Nested Hyper-V VM cannot ping the default gateway

  Hello

  At first, I have to say that I don't consider myself an expert produced a VMware.

  I've been struggling with my test environment nested for a while and finally decided to get help (I hope) of pros.

  Environment looks like this:

  • Physical VMware ESXi 5.1.0 ("Promiscuous" mode enabled for the vSwitch)
    • Couple of virtual machines, one of them being Hyper-V (Windows Server 2012 R2) server that is configured for nested virtualization - 10.106.5.27
      • On the Hyper-V server, I have a VM in Windows Server 2012 R2 - 10.106.5.28

  Hyper-V server has a NETWORK card and full network connectivity (internal and external: Internet) and in the Hyper-V Manager, a virtual switch is configured in external mode.

  VM is connected to this virtual switch via a virtual network adapter. It has public static IP assigned with mask subnet, default gateway, and DNS even as a Hyper-V host. I ping times by IP and DNS name of the host of VM and vice versa. I cannot ping other resources of the virtual machine as the default gateway and DNS ("request timed") servers out. State of the network in the network and sharing Center is VM:

  • unidentified network
  • Public network
  • type of access: no internet access

  When I run the tool for troubleshooting problems on VM, he says "the default gateway is not available". As I said I can not ping.

  I think that all my connectivity problems are caused by the unavailability of the gateway by default on the virtual machine, but I have no idea how to solve this problem. When you change the settings of the VM card from static to DHCP I can't even ping on the Hyper-V host.

  All servers are joined to the same domain (VM has been migrated to ESXi, so he joined to the domain before, but I can't connect to using domain accounts, probably due to network issue).

  I hope I described the problem enough, but please let me know if you need more information.

  Try to activate forged passes also on the vSphere vSwitch as you do for the Promiscuous Mode.

• ESXi 5.5 - Virtual Machine fails to PING the gateway and/or other hosts

  Hello ladies and gentlemen

  I have installed HP DL380p Gen8 1 with vmware ESXi 5.5.

  I have 1 with 2 vmnic Virtual Machine port group - vmnic0 and vmnic1 connect 2 virtual machines. If I have the TEAM network cards, a VM (selected) randomly is able to PING to the gateway while the 2nd VM is not. ESXTOP in this case, don't watch not the physical NETWORK card that each virtual computer connects to but says 'all' to the title of the team-TEDDY.

  If I break the team and you use only vmnic0 - none of the VMs connet to the gateway. If I create the vSwitch with only vmnic1 as usable NIC (vminc0 - unused) - once again only 1 VM (randomly chosen) is able to PING the gateway while the other is not (and two VMS use vmnic1 as the uplink to the vNIC).

  The physical ESX host connects to a Catalyst Cisco 2950 switch.

  Can you please advise where can I go from here? It could be a problem with the VLAN when it comes to vmnic0 (since none of the virtual computers are able to connect through this vmnic), but what is happening with vmnic1 (a virtual machine connects randomly while the other doesnot)...?

  I tried several forums without success.

  Managed to solve this one-

  1. The uplink switch (Catalyst 2950) was Port security enabled on all THE Ports.
  2. I had to disable the port on a given set of ports security (to which are connected the physical network adapters).

  Everything seems to work fine now.

  Bravo to all the entries!

• Cannot ping sub interface from my remote site VPN gateways

  I can't ping my gateways to interface my remote vpn connection sub

  I can ping 192.6.1.0 network, but can't ping network 192.6.2.0 or 192.6.3.0

  When I remote desktop in 192.6.1.20 I can ping all the networks, including gateways to interface sub.

  I think that something in my asa is misconfigured or not added

  ASA NAT rules:

  Exempt NAT Interface: inside

  Source 192.6.0.0/16

  Destination 192.6.10.96/27

  Static NAT interface: inside (it's for the local NAT of E0/0 out)

  Source 192.6.1.1/16

  Interface translated outside the Destination: 172.35.221.200

  Dynamic NAT interface: inside

  Source: no

  Destination: outside

  ASA access rules:

  Permit outside

  Source: no

  Destination: out

  Services: udp, tcp, tcp/http

  Static routes:

  Interface: Outside > network: all outdoors DSL (shows no DSL in the graph)

  

  Some incorrect configuration:

  On the ASA:

  (1) directions are incorrect, the default should point to the next hop route, that is to say: the internet router: 172.35.221.x, as follows:

  Route outside 0.0.0.0 0.0.0.0 172.35.221.x

  ---> where x must be the router internet ip address.

  existing routes need to be removed:

  No route outside 0.0.0.0 0.0.0.0 192.298.47.182 255

  No route outside 0.0.0.0 0.0.0.0 172.35.209.81 in tunnel

  (2) the following declaration of the static NAT is incorrect too and should be removed:

  static (inside, outside) USSLTA01_External USSLTA01 netmask 255.255.255.255

  --> You can not NAT interface on the SAA itself.

  (3) for the SAA within the interface's subnet mask should be 255.255.255.0, no 255.255.0.0. It should be the same as the router interface subnet mask:

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.6.1.254 255.255.255.0

  (4) on the way to access these sub interfaces subnet on the SAA as follows:

  Route inside 192.6.2.0 255.255.255.0 192.6.1.235

  Route inside 192.6.3.0 255.255.255.0 192.6.1.235

  Route inside 192.6.4.0 255.255.255.0 192.6.1.235

  On the router, configure it by default route as follows:

  IP route 0.0.0.0 0.0.0.0 192.6.1.254

• Cannot ping hostname IB gateway

  Hello

  I installed virtual PeopleSoft HCM Image 9.2.012 on my laptop, with PeopleTools 8.54.08.

  I IB Gateway URL as http://hcmdmo.ps.com:8000/PSIGW/PeopleSoftListeningConnector , because I created this hostname during the configuration of the Virtual Machine.

  Now when I ping the gateway, a new popup window with the message "server not found".

  But if I change the URL to http://192.168.56.101:8000/PSIGW/PeopleSoftListeningConnector, then it shows as active gateway.

  Please help me solve the problem. How I can ping the gateway with the host name?

  Thank you and best regards!

  Add the name to your hosts file.  On windows, which would be in C:\Windows\System32\drivers\etc\hosts

  you add:

  192.168.56.101 hcmdmo.ps.com

• Comments of the ESXi5 cannot ping gateway

  Hello

  Structure of the environment

  
  Router (192.168.6.1)
  -Linux
  Virtual machine workstation - 8
  -ESXi5 (192.168.6.220)
  -srv01 ((Win2008r2) (192.168.6.221)(static pi))
  -srv02 (WIn2008r2) (192.168.6.111) (DHCP)

  Srv01 can ping srv02
  Srv01 can ping ESXi5
  Srv01 cannot ping

  SRV02 can get the ip address of the server DHCP (192.168.6.1)
  SRV02 can ping srv01
  SRV02 can ping ESXi5
  SRV02 cannot ping router

  Router cannot ping srv01, srv02
  Router can ping ESXi5

  Question:
  What should I do:
  to get srv01 ping router
  to get the router to ping srv01?

  See http://kb.vmware.com/kb/287 for instructions on enabling virtual for your ethernet adapters promiscuous mode.

• VMmachine cannot ping to the gateway

  VMWare Workstation 7.1.3 build-324285

  Host: win7 64-bit

  Guests: 3 x Red Hat Linux 32-bit, network: filled

  VMMachines (VMM) can connect to each other with success, but non of them can ping the gateway, then they have no connection to the host, or other physical machines, neither the army nor other physical machines can connect to the VMMs.

  Any idea what to do?

  you have disabled auto fill in the virtual network Editor?
  If this is not the case-how now

  the new can begin troubleshooting

• Cannot ping Lan devices in Vlan

  Hello

  I looked for a solution to this for the week without success. I came across a Cisco C3560, which is used because of its ability of poe to power some Deskphones Voip. While the works of great poe, machines connected to the switch can only communicate with each other and don't can't ping or otherwise access any device connected directly to the router of the network.

  The Cisco switch is configured with a vlan and a default gateway, but nothing comes out by behind the switch. On connected devices can ping by default gateway (192.168.0.1 - a tp-link router), receive a lease dhcp from the router said successfully and can connect to the internet, but on the local network, nothing works. (unable to connect to the printer connetced directly to the router or other computers connected directly to the router.

  Any advice? I am new to cisco switches, don't know what I'm doing here. I'm just trying to get devices that are connected directly to the switch to communicate with devices connected directly to the router.

  Switch#show runBuilding configuration...

  Current configuration : 1528 bytes!version 12.2service configno service padservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname Switch!enable secret 5 {}{}{}{}{}{}{}{}{}{}{}{}!no aaa new-modelclock timezone UTC 2system mtu routing 1500ip subnet-zero!!!!no file verify autospanning-tree mode pvstspanning-tree extend system-id!vlan internal allocation policy ascending!interface FastEthernet0/1!interface FastEthernet0/2!interface FastEthernet0/3!interface FastEthernet0/4!interface FastEthernet0/5!interface FastEthernet0/6!interface FastEthernet0/7!interface FastEthernet0/8!interface FastEthernet0/9!interface FastEthernet0/10!interface FastEthernet0/11!interface FastEthernet0/12!interface FastEthernet0/13!interface FastEthernet0/14!interface FastEthernet0/15!interface FastEthernet0/16!interface FastEthernet0/17!interface FastEthernet0/18!interface FastEthernet0/19!interface FastEthernet0/20!interface FastEthernet0/21!interface FastEthernet0/22!interface FastEthernet0/23!interface FastEthernet0/24 switchport mode access!interface GigabitEthernet0/1!interface GigabitEthernet0/2!interface Vlan1 ip address 192.168.0.26 255.255.255.0 no ip route-cache!ip default-gateway 192.168.0.1ip classlessip default-network 192.168.0.0ip http server!access-list 1 permit any log!control-plane!!line con 0line vty 0 4 password XXXXXXXXX login length 0line vty 5 15 password XXXXXXXX login length 0!end

   Switch#show interface

  Vlan1 is up, line protocol is up Hardware is EtherSVI, address is 001e.bd27.c4c0 (bia 001e.bd27.c4c0) Internet address is 192.168.0.26/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 3 packets/sec 138534 packets input, 9472693 bytes, 0 no buffer Received 0 broadcasts (68 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 30296 packets output, 2248820 bytes, 0 underruns 0 output errors, 1 interface resets 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/2 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c484 (bia 001e.bd27.c484) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:56, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 46000 bits/sec, 37 packets/sec 5 minute output rate 582000 bits/sec, 71 packets/sec 1941044 packets input, 327622438 bytes, 0 no buffer Received 38375 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 30699 multicast, 0 pause input 0 input packets with dribble condition detected 3224783 packets output, 2069682884 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  FastEthernet0/4 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c486 (bia 001e.bd27.c486) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129069 packets input, 64947010 bytes, 0 no buffer Received 9953 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 600269 packets output, 45540585 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/6 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c488 (bia 001e.bd27.c488) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:50, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 32693 packets input, 4244428 bytes, 0 no buffer Received 9942 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 588460 packets output, 45003331 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/8 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48a (bia 001e.bd27.c48a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:30, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32694 packets input, 4243413 bytes, 0 no buffer Received 9934 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9757 multicast, 0 pause input 0 input packets with dribble condition detected 588485 packets output, 45009466 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/12 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48e (bia 001e.bd27.c48e) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:28, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32742 packets input, 4252075 bytes, 0 no buffer Received 9947 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9763 multicast, 0 pause input 0 input packets with dribble condition detected 588497 packets output, 45019272 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/13 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48f (bia 001e.bd27.c48f) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:13, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 148160 packets input, 73818106 bytes, 0 no buffer Received 9973 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9760 multicast, 0 pause input 0 input packets with dribble condition detected 599666 packets output, 49045070 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/14 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c490 (bia 001e.bd27.c490) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:05, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129165 packets input, 68409495 bytes, 0 no buffer Received 9982 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9773 multicast, 0 pause input 0 input packets with dribble condition detected 600283 packets output, 45551497 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/18 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c494 (bia 001e.bd27.c494) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:49, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 21000 bits/sec, 18 packets/sec 5 minute output rate 13000 bits/sec, 16 packets/sec 606386 packets input, 88151136 bytes, 0 no buffer Received 159883 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 55198 multicast, 0 pause input 0 input packets with dribble condition detected 941617 packets output, 308269004 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/20 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c496 (bia 001e.bd27.c496) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:54, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 1000 bits/sec, 1 packets/sec 5 minute output rate 1000 bits/sec, 2 packets/sec 515813 packets input, 87006769 bytes, 0 no buffer Received 21466 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 19952 multicast, 0 pause input 0 input packets with dribble condition detected 1858112 packets output, 1700009146 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/24 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c49a (bia 001e.bd27.c49a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 546556 packets output, 41182636 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  GigabitEthernet0/1 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 001e.bd27.c481 (bia 001e.bd27.c481) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 556000 bits/sec, 83 packets/sec 5 minute output rate 76000 bits/sec, 63 packets/sec 4457827 packets input, 3961330567 bytes, 0 no buffer Received 15028 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 11213 multicast, 0 pause input 0 input packets with dribble condition detected 3822373 packets output, 728132696 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  

  Switch#show vlan

  VLAN Name     Status         Ports---- -------------------------------- --------- -------------------------------1     default active    Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16                        Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24, Gi0/1, Gi0/21002 fddi-default act/unsup1003 token-ring-default act/unsup1004 fddinet-default act/unsup1005 trnet-default act/unsup

  VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------1 enet 100001 1500 - - - - - 0 01002 fddi 101002 1500 - - - - - 0 01003 tr 101003 1500 - - - - - 0 01004 fdnet 101004 1500 - - - ieee - 0 01005 trnet 101005 1500 - - - ibm - 0 0

  Remote SPAN VLANs------------------------------------------------------------------------------

  Primary Secondary Type Ports------- --------- ----------------- ------------------------------------------

  Hello

  first thing, please edit your post and remove your remote vty lines access password

  never send passwords on a public forum for the just in case production equipment

  line vty 0 4
  password xxxxxx

  ***********************

  Your question

  What is the configuration of the router as a switch which seems to work correctly you're saying and I configured its doing its job, don't forget you said that you cannot route no between the router and the router switch should take care of this, whats the vlan ports on the router are on is - what the same subnet do they get an ip address in the same subnet off dhcp as devices of switching, if they do, and you cannot ping them to the same subnet theres something upward on the side of the router it would treat for layer 3 routing ip traffic

  the ping to the router devices connected to the cisco switch and can the device on the router cannot ping devices switches

  If you move a device out of the router and attach it to the doe sit switch still work ok, reach the talk of the internet to other devices on the switch?

  As there is a layer 2 switch you don't need this command you have your entry door you can remove it.. .IP default-network 192.168.0.0

• VPN - cannot ping the next hop

  Then some advice... I have configured a server VPN - pptp on my router, create a vpn for the customer at the site. For the moment, the client computer can connect and a connection to the router. I can ping from client to the router (192.168.5.1) but cannot ping 192.168.5.2 (switch) or 192.168.10.X (workstations)

  What I try to achieve is to access the internal network (192.168.10.X), which is the end of the layer 3 switch. Any help/extra eyes would be good.

  Here is my design of the network and the config below:

  Client computer---> Internet---> (1.1.1.1) Cisco router (192.168.5.1) 881---> switch Dell Powerconnect 6248 (192.168.5.2)--> Workstation (192.168.10.x)

  Router Cisco 881

  AAA new-model

  !

  AAA of authentication ppp default local

  !

  VPDN enable

  !

  !

  VPDN-group VPDN PPTP

  !

  accept-dialin

  Pptp Protocol

  virtual-model 1

  !

  interface FastEthernet0

  Description link to switch

  switchport access vlan 5

  !

  interface FastEthernet1

  no ip address

  !

  interface FastEthernet2

  no ip address

  !

  interface FastEthernet3

  switchport access vlan 70

  no ip address

  !

  interface FastEthernet4

  Description INTERNET WAN PORT

  IP [IP EXTERNAL address]

  NAT outside IP

  IP virtual-reassembly in

  full duplex

  Speed 100

  card crypto VPN1

  !

  interface Vlan1

  no ip address

  !

  interface Vlan5

  Description $ES_LAN$

  IP 192.168.5.1 255.255.255.248

  no ip redirection

  no ip unreachable

  IP nat inside

  IP virtual-reassembly in

  !

  interface Vlan70

  IP [IP EXTERNAL address]

  IP virtual-reassembly in

  IP tcp adjust-mss 1452

  !

  !

  !

  interface virtual-Template1

  IP unnumbered FastEthernet4

  encapsulation ppp

  peer default ip address pool defaultpool

  Ms-chap PPP chap authentication protocol

  !

  IP local pool defaultpool 192.168.10.200 192.168.10.210

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy inactive 600 life 86400 request 10000

  !

  overload of IP nat inside source list no. - NAT interface FastEthernet4

  IP route 0.0.0.0 0.0.0.0 [address IP EXTERNAL]

  Route IP 192.168.0.0 255.255.0.0 192.168.5.2

  !

  No. - NAT extended IP access list

  deny ip 192.168.0.0 0.0.255.255 10.1.0.0 0.0.255.255

  IP 192.168.0.0 allow 0.0.255.255 everything

  VLAN70 extended IP access list

  ip [IP EXTERNAL] 0.0.0.15 permit 192.168.10.0 0.0.1.255

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq smtp

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq www

  permit any eq 443 tcp [IP EXTERNAL] 0.0.0.15

  permit tcp [IP EXTERNAL] 0.0.0.15 any eq field

  permits any udp [IP EXTERNAL] 0.0.0.15 eq field

  list of IP - VPN access scope

  IP 192.168.10.0 allow 0.0.1.255 10.1.0.0 0.0.1.255

  Licensing ip [IP EXTERNAL] 0.0.0.15 10.1.0.0 0.0.1.255

  WAN extended IP access list

  !

  Layer 3 switch - Dell Powerconnect 6224

  !

  IP routing

  IP route 0.0.0.0 0.0.0.0 192.168.5.1

  interface vlan 5

  name "to connect to the Cisco router.

  Routing

  IP 192.168.5.2 255.255.255.248

  output

  !

  interface vlan 10

  "internal network" name

  Routing

  IP 192.168.10.1 255.255.255.0

  output

  !

  interface ethernet 1/g12

  switchport mode acesss vlan 5

  output

  !

  interface ethernet 1/g29

  switchport mode access vlan 10

  output

  !

  Hi Samuel,.

  I went through your configuration and picked up a few problematic lines...

  First of all, you can't have your vpn-pool to be in the range of 192.168.10.x/24, because you already have this subnet used behind the switch (this would be possible if you had 192.168.10.x range connected directly to the router). In addition, you may not link your virtual model to the WAN ip address, it must be bound to an interface with a subnet that includes your IP vpn-pool range.

  The cleaner for this is,

  Create a new interface of back of loop with a new subnet

  !

  loopback interface 0
  

  192.168.99.1 IP address 255.255.255.0

  !

  New vpn set up, pool

  !

  IP local pool defaultpool 192.168.99.200 192.168.99.210

  !

  Change your template to point the new loopback interface,

  !

  interface virtual-Template1

  IP unnumbered loopback0

  encapsulation ppp

  peer default ip address pool defaultpool

  Ms-chap PPP chap authentication protocol

  !

  All vpn clients will get an IP address of 192.168.99.200 192.168.99.210 range. And they will be able to get the router and up to the desired range 192.168.10.x/24 behind the router. Packages get the switch, then to the host. Host will respond through the gateway (switch)-> router-> Client.

  PS: Sooner, even if your packages arrive at the host, the host will never try to send the response back through the gateway (switch) packets because STI (hosts) point of view, the package came from the same local network, so the host will simply try to "arp" for shippers MAC and eventually will expire)

  I hope this helps.

  Please don't forget to rate/brand of useful messages
  

  Shamal

• Router and Switch cannot ping each other

  Hello

  I just build a lab at home.

  In my current lab, I have 2 SW and 3 the router.

  I have a problem, I do not know what Miss me in my config. My router cannot ping my SW.

  and I also want to change my LAN from VLAN 1 interface connection at 30 of VLAN... but when I configure the VLAN 30 he show me line is in PLACE but the Protocol is DOWN.

  Another question, if I want to create a VLAN with a different address, what should I do?

  for example

  VLAN 10 > 10.10.10.1

  VLAN 20 > 20.20.20.1
  etc...

  interface Vlan1 description LAN ip address 10.10.10.1 255.255.255.0 secondary ip address 30.30.30.1 255.255.255.0 secondary ip address 40.40.40.1 255.255.255.0 secondary ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!

  Here's the conf for my RT. ROUTER > 877SW > 2950 24 WS

  CISCO_877#sh runBuilding configuration...
  
  Current configuration : 3468 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname CISCO_877!boot-start-markerboot-end-marker!enable secret 5 $1$.ISW$71jzJ0Or0nenXZd/8D8.x/!no aaa new-model!!dot11 syslogip cefno ip dhcp use vrf connectedip dhcp excluded-address 20.20.20.0 20.20.20.30!ip dhcp pool LAN network 20.20.20.0 255.255.255.0 domain-name SYS.local default-router 20.20.20.1  dns-server 202.123.2.6 202.123.2.11  lease 0 4!!!!!username admin privilege 15 secret 5 $1$A1V4$GR9sPtPVXDRoOiDKRtC1M1! ! archive log config hidekeys!!!!!interface ATM0 description (OUTSIDE)ADSL_WAN no ip address no ip redirects no ip unreachables no ip proxy-arp no atm ilmi-keepalive pvc 8/35  encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto !interface FastEthernet0!interface FastEthernet1 dot1q tunneling ethertype 0x9100!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description LAN ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!interface Vlan30 description LAN no ip address no ip redirects no ip unreachables no ip proxy-arp shutdown hold-queue 100 out!interface Dialer0 description WAN_OUTSIDE ip address negotiated ip mtu 1498 ip nat outside ip virtual-reassembly max-reassemblies 1024 encapsulation ppp ip tcp adjust-mss 1400 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname [email protected]/*  */ ppp chap password 7 071C385F5C001D0403 ppp pap sent-username [email protected]/*  */ password 7 120A1C04000208053E ppp ipcp mask request ppp ipcp route default ppp ipcp address accept!ip default-gateway 20.20.20.1ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0ip route 10.10.10.0 255.255.255.0 Vlan1!no ip http serverno ip http secure-serverip nat inside source list 110 interface Dialer0 overload!access-list 110 permit ip 20.20.20.0 0.0.0.255 anyaccess-list 110 permit ip 10.10.10.0 0.0.0.255 anyaccess-list 110 permit ip 30.30.30.0 0.0.0.255 anyaccess-list 110 permit ip 40.40.40.0 0.0.0.255 anyaccess-list 110 permit ip 50.50.50.0 0.0.0.255 anyaccess-list 110 permit ip 60.60.60.0 0.0.0.255 any!!!control-plane!banner motd ^C
  
  :'######::'##::::'##:'########::'######::'##::::'##:'##... ##: ##:::: ##: ##.....::'##... ##: ##:::: ##: ##:::..:: ##:::: ##: ##::::::: ##:::..:: ##:::: ##:. ######:: #########: ######:::. ######:: #########::..... ##: ##.... ##: ##...:::::..... ##: ##.... ##:'##::: ##: ##:::: ##: ##:::::::'##::: ##: ##:::: ##:. ######:: ##:::: ##: ########:. ######:: ##:::: ##::......:::..:::::..::........:::......:::..:::::..::
  
  ^C!line con 0 no modem enableline aux 0line vty 0 4 password 7 xxxx login!scheduler max-task-time 5000end
  
  CISCO_877#

  And this is for my SW

  CATALYST_2960_01#sh runBuilding configuration...
  
  Current configuration : 5166 bytes!version 12.1no service padservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname CATALYST_2960_01!enable secret 5 $1$MGrN$PtHgL3KfH0vy7Mr1Fo0hF.!ip subnet-zero!ip ssh time-out 120ip ssh authentication-retries 3vtp mode transparent!!spanning-tree mode rapid-pvstno spanning-tree optimize bpdu transmissionspanning-tree extend system-idspanning-tree vlan 1-4093 priority 16384!!!!vlan 10 name ADSL!vlan 20 name GUEST!vlan 30 name MANAGEMENT!interface Port-channel1 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate spanning-tree cost 1!interface FastEthernet0/1 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/2 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/3 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/4 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/5 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/6 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/7 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/8 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/9 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/10 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/11 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/12 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/13 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/14 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/15 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/16 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/17 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/18 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/19 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/20 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/21 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/22 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/23 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface Vlan1 ip address 20.20.20.2 255.255.255.0 no ip route-cache!interface Vlan10 no ip address no ip route-cache shutdown!interface Vlan30 no ip address no ip route-cache shutdown!ip default-gateway 20.20.20.1ip http server!line con 0line vty 0 4 password 7 xxxx loginline vty 5 15 login!!end
  
  

  Thanks in advance.

  Eliane,

  Please remove the etherchannel port f0/24 of the switch configuration and store it in the trunk.

  interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active  <<< Remove this 

  Configure f0 on the router as trunk I think has 877, a switchport which fe interfaces are a part of. To display the corresponding Lass on the router, that you need to configure the VLANS corresponding on the router, then only the Lass will be in a State of going / up otherwise it will be in a down state. See if that helps. Thank you, hyacinth

• Cannot ping new addresses IP vmkernel

  I created a few exchanges of vmkernel iSCSI in new bond for our 10G storage on a new vSwitch but I can't ping the IP addresses assigned to them (10.1.45.187 and 188). I have the same setup on a different host and it works very well. I swapped the connections on the 10G switch with those of the host of work as well as cables, so I know it isn't a switch port, the switch config issue or the cable. I even swapped the IP with the work those just to make sure.

  But if I SSH to another host on the same network I can ping those IP vmkernal addresses I can't from my desktop. I can also ping vmkernel IP addresses on the host of my office work that is on the same subnet as the host of non-working. I cannot ping the vmkernel IPs of a host on a different subnet, but can ping ports vmkernel work of host to a host on another subnet.

  I don't know that it's just something simple that I'm missing... I hope!

  Don't ask me why I have not found this before, but here's the answer to my question. I can give me points?

  VMware KB: Ping ICMP in 5.1 and 5.5 ESXi ESXi response behavior change