Nested Hyper-V VM cannot ping the default gateway

Similar Questions

• Cannot ping the default gateway with Centrino Advanced-N 6235 on XPS 12 but CAN connect to the Internet

  I have a XPS 12 with an Intel Centrino Advanced-N 6235 wireless card.  I can't ping the default gateway with the wireless card.  When I use a USB network adapter, I can ping the default gateway for the wired connection.  I can connect to the Internet and the internal network with the wireless card and can ping other computers on the network.  I am trying to run a program to connect wireless to a projector.  I have two different programs for the two different projectors.  I can connect by cable but not wireless.  I think that the problem is anything that does not make me a ping of the default gateway or something on the wireless card.  I have a 10 latitude with a Broadcom wireless card that is connected to the same access point and can ping the default gateway and can connect wirelessly to two projectors.  They all have two windows 8 Pro.

  I downloaded the new drivers from Dell, uninstalled, reinstalled, tried to update Windows install the drivers, all with no success. Any ideas?

  The solution of the problem by chance.  I was connected to the computer with a different network than what has been used to authenticate user account on the wireless.  When I switched the user account for the user account that was logged on to the computer was the same who authenticate to the wireless, it worked.  Go figure!

• ESX host cannot ping the default gateway.

  Hi Experts,

  I have connected ESX hosts to switch cisco as well by the ILO and other ports.

  Cisco switch configuration;

  int gig 1/0/21 and 1/0/13 gig and gig 1/0/14 are configured as access ports because they are carriers/tagging vLan as a 306.

  Cisco switch, I can ping the ip address of the ILO, but I can't ping the IP address management and vice versa.

  IP Managment

  10.197.204.10

  255.255.255.0

  10.197.204.1

  VLAN 306

  Attached the screenshot shown in the diagram.

  your help will be appreciated.

  Concerning

  Don't know what it is, but there must be something simple that you miss

  Let's go through each step of configuration for both ESXi network connections (ILO work already, so we do not touch).

  Check the configuration of switch port physical interface GigabitEthernet1/0/13 and 1/0/14.

  switchport access vlan 306

  switchport mode access

  spanning tree portfast

  Only connect the cable network for vmnic0 to host and make sure what vmnic0 presents itself as 'connected' in the DCUI

  

  Make sure the VLAN ID is empty.

  

  Make sure you then the IP settings are correct (IE without typos,...) and restart the management network from the main menu.

  André

• Cannot set the default gateway in ESXi6.0.0 Update 1

  Hi team,

  I'm recently set up esxi 6.0.0 update1a on a Dell Poweredge M915 server. When I set up the IP address and gateway DCUI I get error below, I do not know why.

  Enable management network errors:

  Default gateway setting has not failed to set the gateway address vmkernel to X.X.X.X there is no VMkernel interfaces on the same network with this IP address.

  Help, please.

  Try to set the mask of the host to 24 (255.255.255.0), then network IP and the IP of the gateway management will be on the same network.

• Cannot ping the Virtual Machine by host

  Hi all,

  Please help, I use VMWare Workstation 6.5 and I have a physical operating system which is Windows XP SP2, I have a network card, but not connected to a physical switch, the IP address is 192.168.0.1. I installed a Virtual Machine using Microsoft Windows 2003 server as the operating system, promote as domain controller, install the DHCP, DNS service and assign an IP 192.168.0.2, no default gateway.

  My VMnet1 on physical operating system has an IP 192.168.204.1 and VMNet8 has an IP 192.168.126.1.

  The host, I cannot ping the 192.168.0.2 which is the IP address of the Virtual Machine. Even in the Virtual Machine, I can not ping 192.168.0.1 is the IP address of the host. From what I read, the physical and the virtual machine were connected with a virtual switch. Am I wrong?

  Any advice?

  Thanks in advance.

  They SEEM to be in different networks, you need search routing between them,... since they differnet networks...

  on the other

  they do host and the virtual machine on the same subnet / network for EXAMPLE: class C class network 192.168.200.0/24

  granting of points if my answer was helpful... Thank you > > > > > > > >

  concerning

  Joe

• Do not open the video file with the error "the file you download cannot open the default program".

  By double clicking on a file video I now get the following message "the file you download cannot open the default program" while previously he opened the file. This occurred after using Microsoft Fix - it for trial purposes, so what has changed.

  Original title: this message is received when I try to open a file by clicking twice - the file you download cannot open the default program

  Hello

  1. Are you dealing with the issue is with the opening of specific or all video files video files?
  2. What is the name of Microsoft fixit are you referring to?

  Set by default to read video files and verify if works.

  Change the programs that Windows uses by default:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-which-programs-Windows-uses-by-default

  It will be useful.

• Signed .bar - cannot find the default application

  Hello

  a friend send a link to his game app signed .bar to consult. (The game is created with Air 2.5 if it matters)

  I downloaded it with the BlackBerry browser and when I try to open the .bar, an error message appears

  "Cannot find the default application"

  
  I've already put my developer intro PlayBook (OS 2.1) mode.

  How to install the .bar file?

  Thank you.

  Vibes

  You need to side load the folder bar. A lot of discussion on that.

• Cannot change the default mode in wscript

  In Windows 7, when I try to change the default mode of wscript, I get an error message. When I get home

  CScript //H:CScript

  the command line, I get

  CScript error: cannot change the default script host

  What should I do?

  Open command prompt w / administrative permissions (right click, run as administrator), and then run the command:
  cscript //h:cscript //s //nologo

• After that stright connected to iSCSI (initiator) Host cannot ping the server iSCSI (target), but the target can, why?

  After that host on vSHere 4.0 strightly connected to iSCSI (initiator) host cannot ping the server iSCSI (target), but target can.  And iSCSI works well. I mean I can create and use the iSCSI disk, why? It makes me confused.

  Thank you!

  Geoarge,

  iSCSI traffic uses a VMkernel port, instead of using the command 'ping', use 'vmkping '.

  André

• Cannot change the default IP address after the upgrade to 4.1

  We just migrated a client 4235 ID version 3.x to 1.0000 S47 using the Ugrade/Recovery CD 4.1

  We try to apply the basic configuration as change the host name & IP address using the command CLI "SETUP." Whenever we apply the changes by selecting the appropriate item (2 - save this configuration configuration and output), im getting this error "error: could not restart network services.» Unrecoverable error occurred. Node MUST be restarted to activate alarming. »

  Below is the output that we captured during the initial configuration process:

  Installing sensor #.

  -System Configuration dialog box-

  At any time you can enter a question mark '?' for help.

  User ctrl-c to interrupt the configuration at any prompt dialog.

  Default settings are in square brackets "[]".

  Current configuration:

  networkParams

  IP 10.1.9.201

  netmask 255.255.255.0

  Passerelle_par_defaut 10.1.9.1

  sensor hostname

  telnetOption disabled

  accessList ipAddress 10.0.0.0 netmask 255.0.0.0

  output

  timeParams

  summerTimeParams

  Active selection no

  output

  output

  Web service server

  General

  ports 443

  output

  output

  Currently: game Aug 26 10:13:29 2004

  Last modified configuration: Thu Aug 26 10:12:46 2004

  Continue with the configuration dialog box? [Yes]:

  Enter the host name [sensor]: IDS02

  Enter the IP [10.1.9.201]: 10.1.2.4

  Enter the network mask [255.255.255.0]:

  Enter the default gateway [10.1.9.1]:

  Enter the server telnet [disabled] State:

  Enter the web server port [443]:

  Change the current access list? [None]:

  Change the system clock settings? [None]:

  The following configuration has been entered.

  networkParams

  10.1.2.4 ipAddress

  Passerelle_par_defaut 10.1.9.1

  hostname IDS02

  accessList ipAddress 10.0.0.0 netmask 255.0.0.0

  output

  timeParams

  summerTimeParams

  Active selection no

  output

  output

  Web service server

  General

  ports 443

  output

  output

  [0] go to the command prompt without saving this config.

  [1] return to the configuration without saving this config.

  [2] save this configuration and exit.

  Enter your selection [2]: 2

  Error: Could not restart network services. Unrecoverable error occurred. Node MUST be restarted to activate the alarm.

  I'm also the same error on the first ID 4235 we just bought, pre installed with 4.1. We have changed the IP address each time, we get the same error w/c is "error: could not restart network services.» Unrecoverable error occurred. Node MUST be restarted to activate alarming. »

  I just wonder of bec before that, we changed the IP address & front door for a couple of times & we don't have this kind of problem. The IP address change has been done during the test phase of activities & the problem came only when we already have this ID on the production. My client has just need to change the IP address beak of some changes in the network.

  We tried to restart two IDs, but the problem remains.

  I am trying to get some technical info on the site Web of TAC, but I can't find anything.

  Hope you can help me on this one.

  Thank you very much.

  your default gateway is incorrect. fix that, and you should be good to go.

  Thank you

  Chris

• My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available.

  My internet connection laptop keeps dropping out. This utility solves temporarily, saying the default gateway of something is not available. How can I permanently?

  Hello

  1. who is the operating system installed on your computer?

  2. are you using a cable or a wireless Internet connection?

  3. were there any changes or updates made on the computer?

  4. what store did you try?

  Follow the steps mentioned below and check.

  Method 1: I suggest you to return the item and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  You can try resetting WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.

  a. Click Start and in the search box, type cmd.

  b. right click on command prompt, select "Run as Administrator" to open a command prompt.

  c. at the command prompt, type the following commands:

  netsh winsock reset catalog, which resets the WINSOCK entries to the default installation

  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation

  netsh int ipv6 reset reset.log resets the IPv6 TCP/IP stack by default installation

  d. restart the computer.

  Method 3:

  Reset the default router by pressing the reset for 15 seconds with power button.

  a. turn off the modem, the router and the computer.

  b. connect the modem to the WAN/Internet port on the router.

  c. connect the computer to one of the router's LAN/network ports.

  d. turn on the modem, wait for triggering connect light.

  e. turn on the router, wait two minutes.

  f. start the computer.

  g. when the computer is completely loaded, check if the problem persists.

• My internet rpet 'unidentified network' + "the default gateway is not available"...

  My internet was working fine before, but now repeat me 'unidentified network' and I know that's not my internet because I have another laptop that uses the internet itself very well. Then when I try to solve problems, he said "the default gateway is not available"... of the suggestions?

  Hello

  ·         Did you do last changes made on your computer before the show?

  ·         Using internet connection wired or wireless?

  Method 1:

  Follow the steps in troubleshooting from the link and check if that helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Temporarily disable the firewall on your computer and check if it makes a difference.

  Reference:
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Note: Makes sure to turn Windows Firewall back, once you have done the troubleshooting.

  Method 3:

  Reset WINSOCK, TCP/IP IPv4 and IPv6 TCP/IP stack.
  a. Click Start and in the search box, type cmd.
  b. right click on command prompt, select "Run as Administrator" to open a command prompt.
  c. at the command prompt, type the following commands:
  netsh winsock reset catalog which resets the WINSOCK entries to the default installation.
  netsh int ipv4 reset reset.log that resets the stack TCP/IP IPv4 default installation.
  netsh int ipv6 reset reset.log resets the default install IPv6 TCP/IP stack.
  d. restart the computer.

  Also, see this KB article:

  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357

  Kind regards

• WRT350N: how to specify the default gateway?

  Hello

  I want to use my wrt350n as dhcp server, but to specify another router as the default gateway.

  I have my wrt350n (192.168.1.254) and another modem/router (192.168.1.1). When a client connects to the wrt350n, it is automatically assigned as the default gateway address of the wrt350 (192.3168.1.1). I would like to change it to refer to the other address 192.168.1.1.

  Thanks for your comments

  Raph

  On the configuration, on the basic settings tab page, there is facility of the Internet and network configuration. Setup of the Internet is for the WAN. Assign The DHCP Auto - Configuration so it will automatically get an IP address from the modem/router.

  On the configuration of the network, local IP address should be 192.168.2.1, subnet mask 255.255.255.0. This is where you enable DHCP. The default gateway should be 0.0.0.0 and that's fine, it assigns the LAN IP of the router.

  Once you have saved it, your router configuration page now is 192.168.2.1 and configuration page of your modem/router is 192.168.1.1.

• Losing Internet connection because of the default gateway is not available.

  I keep losing internet connection and when I run the troubleshooter, it comes up saying "the default gateway is not available". I have an HP with Intel dv6985se. I was advised to do the following:
  I had the same problems of chance which I fixed it by simple disabling 'SLEEP ON DISCONNECT' SideScalng disconnect

  1 Access Device Manager (Control Panel > system and security > system > Device Manager)
  2. expand the network adapters
  3. Select the adapter that you are using (if more than 1 Repeat step 4 to 8 for each adapter)
  4. right click and select Properties
  5 click Advanced
  6. If you have installed Nvidia Ethernet configuration click the button
  7. scroll to the bottom of the list and disable the device sleep on disconnection and receive Side Scaling
  8. save the settings

  I appreciate this help info but none of this applies to my computer has. In my device under 'Network adapters' Manager, I do not have Nvidia, Asus and AMD, which is listed under my network cards is "Intel Wireless WiFi Link 4965AGN" and "Realtek RTL8101E Family PCI - E Fast Ethernet NIC (NDIS 6.20)".

  The help that I've provided says disabling "Sleep on Disconnect" and "Receive Side Scaling"... or those who are in one of my "adapter properties tab advanced options" for both my Intel and Realtek... no where does say anything about sleep on disconnect or side scaling.

  I was online with HP cat many times and Ive tried the options they have provided that is basically what I've found here but nothing has worked so far! My computer is 1 1/2 old and is preinstalled with Vista 64-bit. Recently, I have completely restored my computer with Windows 7 64 bit, and ever since then, I can't download anything or talk to HP or any kind of help because I lose the connection. Could someone please help me solve this problem... to be frank and honest he pisses me off beyond words that I never had this problem when I'm on Vista!

  I don't know what else I can provide to better help me to solve this problem, but if anyone would like more information on what programs etc, my computer has let me know and I will provide the information. Below, I'm pasting the info I received through my history of troubleshooting like a Notepad of paper Network Diagnostic and Route.Print document.

  Windows IP configuration

  Name of the host...: Helvis-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: Belkin

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. : Belkin
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-1F-3B-A2-B7-6B
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::58d1:7968:4f2e:e873% 12 (Preferred)
  IPv4 address: 192.168.2.3 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Wednesday, 10 March 2010 19:03:56
  End of the lease...: Sunday, April 17, 2146 01:58:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 218111803
  DHCPv6 DUID customer...: 00-01-00-01-13-1C-37-DE-00-1E-68-7F-D5-C3
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: Realtek RTL8101E Family PCI - E Fast Ethernet NIC (NDIS 6.20)
  Physical address.... : 00-1E-68-7F-D5-C3
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. Belkin:

  The connection-specific DNS suffix. : Belkin
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::5efe:192.168.2.3%14(Preferred)
  ... Default gateway. :
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: disabled

  Tunnel adapter isatap. {BC831AD2-8EB9-45C9-9FB7-D2CF0E447380}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e76:451:18e9:3f57:fdfc (Preferred)
  Address IPv6 local link...: fe80::451:18e9:3f57:fdfc % 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Print route Notepad document:

  ===========================================================================
  List of the interface
  12.. 00 1f a2 b7 6B 3B... Intel (r) Wireless WiFi Link 4965AGN
  11... 1e 00 7f 68 c3 d5... RealTek RTL8101E Family PCI - E Fast Ethernet NIC (NDIS 6.20)
  1... software Loopback Interface 1
  14.. 00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
  15 00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
  13 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
  ===========================================================================

  IPv4 routing table
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.168.2.1 192.168.2.3 25
  127.0.0.0 255.0.0.0 127.0.0.1 on route 306
  127.0.0.1 255.255.255.255 127.0.0.1 on route 306
  127.255.255.255 255.255.255.255 on-link 127.0.0.1 306
  192.168.2.0 255.255.255.0 on binding 192.168.2.3 281
  192.168.2.3 255.255.255.255 on binding 192.168.2.3 281
  192.168.2.255 255.255.255.255 on binding 192.168.2.3 281
  224.0.0.0 240.0.0.0 on-link 127.0.0.1 306
  224.0.0.0 240.0.0.0 on binding 192.168.2.3 281
  255.255.255.255 255.255.255.255 on-link 127.0.0.1 306
  255.255.255.255 255.255.255.255 on binding 192.168.2.3 281
  ===========================================================================
  Persistent routes:
  None

  IPv6 routing table
  ===========================================================================
  Active routes:
  If metric network Destination Gateway
  13 58: / 0 sur-lien
  1 306: 1/128 liaison
  13 58 2001: / 32 on a link
  2001:0:4137:9e76:451:18e9:3f57:fdfc 13 306 / 128
  Over a link
  12 281 fe80: / 64 On-link
  13 306 fe80: / 64 On-link
  FE80::5EFE:192.168.2.3/128 14 281
  Over a link
  FE80::451:18e9:3f57:fdfc 13 306 / 128
  Over a link
  FE80::58d1:7968:4f2e:e873 12 281 / 128
  Over a link
  1 306 ff00: / 8 On-link
  13 306 ff00: / 8 On-link
  12 281 ff00: / 8 On-link
  ===========================================================================
  Persistent routes:
  None

  Helvis,

  If the error does not recur in safe mode then there is probably a startup item or service causes the error. Follow the steps on the following link to locate the item or service responsible for the error:

  http://support.Microsoft.com/kb/929135

  Hope that helps!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• KICKED OFF & REVIEW DOWNLOAD error "Unable to connect to the default gateway"

  Why am constantly kicked offline with message saying unable to connect to the default gateway? Must constantly to troubleshoot every 30 minutes and restart the router, and also more recent update more critical MSFT will not download? k

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/wifi-keep-disconnect-troubleshoot-default-gateway/369ae5a0-2C25-46EE-B64F-437907d5ade6

  http://Windows.Microsoft.com/en-AU/Windows/configuring-multiple-network-gateways#1TC=Windows-7

  Two threads above can help with the router.