Evacuation of SAN

Similar Questions

• Google shows my weather situation as San Francisco.

  I live in Buckingham (Dallas).  I don't know how this change in San Francisco.  It has just shown one day a couple of weeks and the system won't let me come back to my correct location for the weather.  Called Apple Support and no help.  Referred me to the Weather Channel, but so far, did not get anything else than voice mail.  What happened and how do I get my time back to Buckingham (Dallas)?  I have a Time Machine backup but am wary to try this first.

  Have you checked the Date and time preferences?

• Following the upgrade to 34.0.5, I can access is no longer our SAN, airco, vSphere customers Web web pages, etc. How can I fix this?

  After upgrade to 34.05, can no longer access the web pages of the SAN, the air conditioning system, vSphere Client Web management interface, etc. All still work in Chrome.

  The air conditioning system gives an error:

     Firefox cannot guarantee the safety of your data on 10.32.16.50 because it uses SSLv3, a broken security protocol.
     Advanced info: ssl_error_no_cypher_overlap
  

  The management interface SAN and vSphere customers Web display an empty page. Not sure if they have problems due to SSLv3.

  I understand that you want to be careful, but I seriously doubt that I have to deal with an attack of our SAN. Please, at least give us an option for you connect without worrying.

  Unfortunately, it is not possible so set this preference selectively - with preferences of internal firefox mentioned previously, you can only enable or disable the low globally.

• I would like to install firefox on my mobile of San Francisco - can I do this?

  My Orange San Francisco mobile is unlocked to 3UK and I would run firefox on it.

  It is a phone ARMv6. Mobile Firefox requires a phone that has an ARMv7 support. We investigate adding ARMv6 support if there is no concrete timetable for this work.

• User's home drive do not disconnect on logout - El Cap / SAN / SMB

  10.10.5 managed Server 5.1 customers / 10.11.4 Server and the Profile Manager

  We have recently moved to a new SAN.  Our old SAN (CEM) used to go nuts if we have enabled SMB 2 when connecting with our Macs.  We forced protocol SMB 1 on our customers and this stopped file corruption and the SAN to bananas.

  New SAN (ch) supports SMB 3.  Migrate all user data and found that funny permissions files Mac (movies, music, photos, library etc.).  The "Everyone" group was set to 'Deny' and either remove it, or just refresh perms on a folder that has allowed the correct users access.

  When you use SMB 1 on our new SAN, it was slow as dirt, so we have enabled SMB 3.  Much faster.  Our problems are the following:

  1 - when a new user is created, and they connect for the first time, they get their 'Mac' folders created.  They are made with the funny perms that prevent users who register in these files.  We got around this new users by creating a template for folder for them BEFORE opening of session that contains the correct permissions.  Store us existing users running a monster script to strip and update perms.

  2. when a user logs on to a Mac client in network, their network folder does not disconnect properly, leaving open which means if they connect to another machine their Keychain can go nuts.

  Everyone here has experience with Macs and WITHOUT and dubious permissions?

  Bosco1983 wrote:

  1 - when a new user is created, and they connect for the first time, they get their 'Mac' folders created.  They are made with the funny perms that prevent users who register in these files.  We got around this new users by creating a template for folder for them BEFORE opening of session that contains the correct permissions.  Store us existing users running a monster script to strip and update perms.

  Roughly permissions must be that the owner can access the files and content, but everyone should be declined. As long as the user creates the folder, they should the registered owner.

  Bosco1983 wrote:

  2. when a user logs on to a Mac client in network, their network folder does not disconnect properly, leaving open which means if they connect to another machine their Keychain can go nuts.

  Yes unfortunately network directories have a lot of questions. This is something that I and others have seen as well as various other issues. I have I feel resolved this by putting in place a logouthook script that takes place as his name when the user disconnects, and checks and if necessary disconnects all left to mount the users home directory. Here's my logouthook script.

  #!/bin/bash
  # Kill secd processes left running after user logs out
  killall -9 secinitd
  killall -9 secd
  logger "LogoutHook killed processes"
  # Unmount network home directory share if left mounted after user logs out
  mountpath=`mount | grep /Network | awk '{print $3}'`
  if [ "$mountpath" != "" ]
  then
    umount -f $mountpath
    logger "LogoutHook unmounted network home"
  fi
  # Delete old stuff from /private/var/folders - mainly cache files after user logs out
  # more as a security measure but also helps clear any bad stuff
  find /private/var/folders/* -type d -mtime 1 -exec rm -rf {} \;
  exit
  

• SanLink2 and Dell Compellent SAN?

  Hello world

  I'm currently developing a sharing of the AFP on a Mac Mini with our Dell's Compellent SAN fibre channel storage.

  I have a late 2014 Mac Mini connected through love at first sight for a SanLink2 adapter CF 16 G.  The adapter has two HBA that is connected to our Cisco MDS 9148 fibre channel fabric switches.  The WWPN of the HBA on the adapter have been the subject of a zoning on the fabric buttons, and we cannot FCPING SAN HBA successfully.

  However, we have 2 TB of storage of our Compellent SAN to Dell for the mac mini, and I can't get the mac mini to see volume (do not see it in disk utility and can not see all the new drives in / dev).  I have a support case to open with promise, but he was curious to know if the community had seen.

  I tried fell different cable, different fibers and several reboots.  In my research on Google, I've learned a fun terminal command under OS X: fibreconfig-l [it's a lowercase L].  When I run this command, all I get is the following:

  terminalprompt # fibreconfig-l

  Controllers of

  Targets

  NodeWWN 23:00:00:01:55:5 B: 29:08

  NodeWWN 23:00:00:01:55:5 B: 29:08

  In my monitor OS X system, under the section of Fibre Channel, I get a little more information, but I'm under the impression that I should see (s) Lun in there and I'm not.  Here's what I see:

  Seller: promise

  Product: SANLINK 2

  Review: Firmware 1.1.65.30 material b

  Initiator identifier: 3791655135

  Node World Wide name: 23:00:00:01:55:5 B: 29:08

  Port World Wide name: 24:02:00:01:55:5 B: 29:08

  Address identifier: AE:16:00

  Description: Port 1

  Speed: 4 Gigabit ports

  Topology: Auto (point to point)

  Status: Connection established

  Cable type: optical fiber

  I can provide more information if necessary.  Thanks in advance if anyone has any ideas!

  Hello

  I know some FC HBA require that either a device mapped to LUN 0. For these HBAS if there is no mapped to LUNS 0 none of the storage will be recognized by the client. It has been my experience that whatever it is based on the older chipset of the LSI FC has this problem. The original SanLink FC HBA has no need of any drivers that was also the case for Apple brand LSI FC HBA OSX - thus could perhaps use the some of the previous control logic? Additionally, make sure that you are properly set up as point to point or FC - AL topology in the SANLink 2 configuration utility - this should match what is your San.

  Try this:

  1) map to the storage presented to the Mac with 2 SanLink to LUN 0

  (2) check the topology setting (try it was taking off from point to point auto and try first)

  (3) check if there is of"security groups" on storage that there ID WWN of the SANLink2 registered

  (4) make sure that the storage and the Mac are zoned properly on the FC switch (could be WWN zoning or rezoning of port, in both cases, it must be set up correctly).

  I hope this helps!

  -Jonathon Lee

• Antenna Apple TV screensaver is blocked on San Francisco

  Air screen saver works normally except what happens in San Francisco every time. It was working fine until about two or three weeks.

  Unfortunately there is no way to control what screensaver air rises, outside setting when new are downloaded

  You can give your comments

  http://www.Apple.com/feedback/

• Satellite C660D - evacuated any device from Device Manager wireless

  My * Toshiba Satellite C660D-1 * has suddenly been removed and its wireless Lan adapter. I tried to add the list of legacy hardware to add device manager and all the possible solutions what so ever (believe me I work on it for the last 7 days) but without success. When I switch on the radar screen, it says device wireless disabled. more card flash the F8-wireless switch connection has also disappeared.

  Guys it's really stupid and frustrating. guys please help. I downloaded all the card driver available on the Web from Toshiba site available wireless network. Please help me by replying to this message or send me an email: [email protected]

  any kind of help would be very appreciated. the evacuated any device Wireless Device Manager list and when I added one from legacy devices it says that the software for this device is installed correctly, but it still does not properly errod code: 31

  Have you updated the BIOS or done something that may be responsible for this?

• Appreciate direction correct forum, as if to suggest an emoji Aladdin Sane if necessary

  I would suggest the creation of an emoji Aladdin Sane, if appropriate?

  Tintinrocks wrote:

  I would suggest the creation of an emoji Aladdin Sane, if appropriate?

  Sorry, apple is not responsible for the manufacturing of emoji.

  Using google and you will know that, then you can let them know.

• Migration of data from records on Win2K8 cluster to a new SAN SAN

  I hope that someone here might have a clear answer to my question. We are currently working on a project to migrate all the data of a former SAN that stores our info Win2K8 Cluster (Quorum, MSDTC and SQL DBs) to a new SAN. I know that databases SQL, the plan is to simply detach the DBs with in SQL, stop SQL services, move the DBs from the old drive to the new location and then reconnect, we intend to reuse the drive letter, so that there will be real problems.

  What I'm having a hard time trying to figure out, is how to move successfully the readers of the page Web MSDTC and Quorum, would I simply create a new set and removing the current Quorum and MSDTC leads or is there a way to move the data on the page Web MSDTC and the Quorum of the current location reuse the old drive letters and stored it on the new San without having to change any configuration or break the cluster.

  All clearification would be much help.

  Thank you.

  Hi Vince,.

  This problem would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  Thank you.

• 2 san LUNS have been disassembled automatically need to pull up the same

  Dear Experts,

  last night all of a sudden we found two san LUNS are not mounted on one of the vcb server, but we are able to see the same on a disk management window, need your help how to mount these LUNS without losing any data. How to download buttons pressure or attachment...

  Need urgent help

  concerning

  Mr. VMware

  Hello

  What operating system is installed on the computer?

  Contact VMware support for assistance.

  http://www.VMware.com/support/

  Hope this information helps.

• If win 2003 is upgraded for the 2008 edition, it will fix alingment compensate for the problem with the SAN disks?

  If win 2003 is upgraded for the 2008 edition, it will fix alingment compensate for the problem with the SAN disks?

  Hi elvirkaric,

  Your question in Windows Server 2008 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/w7itproinstall/threads

• How to bring the SAN disk online in win2k8

  I added a few discs san using Iscsi. But all my disks are offline. So is there any command to make all disks both online...

  Hi bharathkumar_Gannu,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the following forum.

  Windows Server 2008 forums

• GTA san andreas does not open with windows 7! How to silve this if you please help me

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: gta san andreas does not open with windows 7! How to silve this if you please help me

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Review the information from the Windows 7 Compatibility Center.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=software&s=Grand%20theft%20auto

  He says that version 2 is not compatible.

  If Aero is the problem, disable it before installing the game and then turn back on.
  I would say as you right-click on Setup and select "Run as Administrator".

  I hope this helps.

  Marilyn

• has been able to play gta vice city and san andras and now I changed the frm windows XP to 7. but now I'm not able to play another game

  original title: card__ graphic

  I was able to play gta vice city and san andras and now I changed the frm windows XP to 7. but now I'm not able to play any other game m .is it probkem of bone or my graphics card?

  -----------------