Export part of the signal in ASCII or excel

Similar Questions

• Determine the position of a part of the signal on a graph

  Hi all

  I have a problem. I determine the position of a part of the signal on a chart. So, I have to determine the maximum value of the part (this is not a problem).

  Signal a lot of noise. I did some filtration but still signal have noise. Concerning this, filter change signal, two later when I take one measure, there is a possibility that this is not true.

  Anyone has idea how to determine the position of a part of a signal automatically, for the various signals (similar).

  There are photos attached where is what belongs to an interest in a signal. There is a VI where is an a test signal.

  Thank you

  Hello

  From the screenshot, I understand that you only interested in the local maximum of the signal.

  There is a VI that detects peaks when you specify a certaing point and this point maximum width.

  Later, it's just a matter of setting the value of local maximum of you. Basically, you'll have to point once again got 1 d table than VI.

  I enclose a VI that can be a good starting point for your application.

  Best regards

  Ion R.

• extract the random part of the signal

  If I'm loading a signal from a LVM file, is there a way to extract a random part of the signal?  Just some information, I load several files through a loop/case structure and each of the files can be of different lengths, so I don't know beforehand how long the signal is.

  Thank you

  George

  The best way to do what you want to do is the following:

  1. Read the file using the Express read the file of measures. It will show the entire file in memory.
  2. This convert a unique waveform or table of waveforms using the Express Of the DDT. This will not create a copy of data.
  3. Point of use of Detection of level trigger base to find the location of your departure.
  4. Get the subset of waveform to pick the section of interest.

  If your waveforms are large enough so that it causes memory problems, you can analyze the text of the file directly, but it is much more complicated and could easily be much slower if you do not quite accurate (see notes above).  If you need to pursue this matter, let know us and we can provide the best direction.

• FPGA acquires only the positive part of the signal

  Hi all

  I have the NI USB-7855R and using the personality of DAQ balanced example of e/s (http://www.ni.com/example/5961/en/). I plugged my generator Agilent to AI0 (in mode CSR) and I have the following problems:

  (1) waveform graph in LabVIEW is only to show the positive part of the sine wave that I am providing to the Board of Directors (clipping at 0 V). Only by compensating the signal from the signal generator, I am able to get the two cycles.

  (2) while I am out 5 Vpp on the generator of signals on the graph of a waveform in LabVIEW I see only 1.5 mVp.

  Any suggestions on what could be the problem?

  Thanks in advance or your help!

  The first graph of "analog input" in your link shows the analog inputs are converted to unsigned integers (U32) before their passage in the FPGA-> host FIFO. Negative values will obviously be lost make this conversion.

• DataPump export part of the table

  Hello
  
  I have the pattern, where I ca. 100 tables and two large tables, with hundreds of millions of records. I want to export the schema with restriction on this two tables with data pump so that only part of the data is exported as custom where condition. Is this possible with expdp?
  I have hard to create the new table in the contours with my selection of data from large tables and then exclude the original paintings using the option EXCLUDE, however it seems to me a waste of resources and time on the server. Welcomes all ideas, thank you!
  
  Published by: kamilp on October 5, 2009 07:25

  Hello

  Yes, just use the query clause and specify a table name:

  Lets say, you want to get everything from the last 10 days of the big table 1

  Anais = large_table_1: ' date_column > sysdate-10.

  If you want to get everything with part_number more than 1000 for large table 2

  Query = large_table_2 "part_number > 1000.

  Use this solution in the export command

  expdp System/Manager schemas directory of my_schema = dpump_dir = my_schema.dmp charly dumpfile = large_table_1: ' date_column > sysdate-10 "query = large_table_2"part_number > 1000.

  Dean

• Exporting part of the EP 7

  I would like to export a part of my project in two hours two minutes to record on DVD or send it to a friend. My project was imported from VHS via a Canopus ADVC 110 analog digital converter and thus is one continuous piece.  I have edited, but now I want to export a particular edited clip. How this is done? Thank you!

  Welcome to the forum.

  There are two simple ways to do so.

  First of all, mark you segment with the WAB (work area bar) and share in DV - AVI w / 48 KHz 16-bit Audio. Then import that into a new DV project, add Menus, and burn to disc.

  Second, do a Save_As, leaving your original project intact. Then, remove all but this segment. Add Menus and burn them on DVD.

  Good luck

  Hunt

• Part of a Signal amplitude

  Hello!

  I managed to find the amplitude of the signal saved as a spreadsheet using Amplitude and Levels.vi together. It works very well. How can I find the part of the signal amplitude (let's say the first 10% or 0.0001 seconds)? In a Word, how do I set up time limits for VI?

  Thanks for your help.

  Judging by your code you seem to have a good understanding of the manipulation of waveform.  You can use the get Wfm subset VI (waveform palette) or just to roll your own hoarder of subset in the tools of the table palette.  The subset of Wfm get has the advantage of calculating the time based on the dt.

• Export button on the Advanced sub-region Switcher does not fetch data in excel

  Hi all

  I have an urgent need.

  The question is:

  I have a Swich area, based on its attribute VO, Case1-> makes Advanced Table1, CAS2-> make advanced table2

  Now, I have exportButton in advance Table1 and Table2 advance.

  After querying data on the page, by clicking the export button set to these tables in advance (in the region of switcher), open the excel file, but with no data in it.

  I looked and I saw in the guide of the OFA switcher column requires setting 'Export the view attribute' but my problem isn't switch column.

  My question is exportButton not work on advanced table that is part of the container case region switch, excel opens without any data in it (advanced table VO has the data displayed on the page).

  Please help with your valuable suggestions.

  Thank you

  Sree

  Hi Mary,

  Visit this link:

  Blog on Oracle of Mukul technology: implementation of export button features programmatically

  Sushant-

• When I try to send an email to multiple recipients, I get this message: "there are non-ASCII characters in the local part of the address of the recipient. This is not

  I bought a new computer. When I try to send an e-mail to multiple recipients, now, I get this message: "there are non-ASCII characters in the local part of the address of the recipient. It is not yet supported. If please change this address and try again. "I don't know what are the non-ASCII characters, so I don't know what to do. I never had this problem on my old computer. Please explain in simple language.

  The 'local' part in the context of email addresses, the part to the left of the symbol @. The warning is a bit of a surprise, because in general the owner of a mail server is relatively free to specify the address format. There is a movement to allow the games to other characters to be used in the fields, so I'm a little disappointed to see that, apparently, e-mail does not support the latter in the local part yet or it can be your SMTP server that generates this message.

  ASCII characters ("American Standard Code for Information Interchange") are, on the whole, the English alphabet, uppercase and lowercase, as well as figures, common punctuation and case of things like the asterisks, obliques and media bars, but not of accented characters. But even apparently simple things like spaces and dashes have cousins who, at first glance, appear to be identical, but are not represented in the ASCII system. I am thinking especially nonbreaking spaces, dash and half-quadratin.

  But I don't know why your new computer must have caused these warnings.

• Qosmio G30-220: HD-DVD via HDMI - error message Impossible to export the signal

  Hello

  When I play a HD-DVD on my G30-220 LCD_panel, it works like a charm (with the Toshiba HD - DVD player software).

  When I switch to dualview to export the signal through HDMI to my LCD TV (HDCP), I get an error message:

  ' Cannot implement the signal. Please switch to the internal display "(this is not the exact English message. I get the error message in Dutch and I've translated).

  Hello

  As much as I know the dual display is not possible. Either watch you on LCD display or on the TV. The two of them at the same time will not work. Reason because it's the protection against copying, and also because of very high data transfer.

  I tested it with Qosmio friends on my LCD HD-ready TV.

• cancel the export of the signal at high level

  Hello

  I try to send a short pulse from a meter out to one of the three PFI consecutively. The lines are supposed to be 'high', when I change from one to the other PFI.

  When I export the signal, the road will remain active, which is not what I need from the pulse will be then output to more than one line.

  I tried almost everything I knew, including research forum, but all I find are to know how to cancel the export by setting the PFI in three States. It is not enough that he let the line logically low.

  All attempts to take over the line by a for example a digital camera output high fail on me.

  Can someone help me?

  Thank you

  Michael

  Hello

  So here's the solution I ended up with. Not very pretty, so if someone has suggestions for improvement, I'll be happy to learn.

  Hello

• Premiere Pro problem: everything get more big, and that part of the clip will be exported...

  

  on the left of the original item, right how looks like I did the color correction. I don't know why it displays only a part of the clip. I can also export only the part that you see on the right.

  It is the same for all projects! :-(

  Set your monitor to MADE it (goes to 100%, where the zoom).

  Open the if who does not show a screendump of parameters of export with the exit on the left.

• PDF of naming when exporting using a part of the file name (JS) IDCS4

  I have a script that will use a PDF Export Preset for each page of a document to export individually. The script uses the ID name of the document and adds a "_Final.

  For example:

  Identity name to docs:

  138-140 TEST 10_WORKER.indd

  Name of the final PDF:

  138-139 TEST 10_WORKER_Final_1.pdf

  138-140 TEST 10_WORKER_Final_2.pdf

  138-140 TEST 10_WORKER_Final_3.pdf

  The first three digits represent the first page number in the document. I want to use these numbers and add gradually to the following PDF page numbering. I'm looking to do using our standard naming convention that looks like this...

  MYTEST_138.PDF

  MYTEST_139.PDF

  MYTEST_140.PDF

  Any guidance would be greatly appreciated. Thank you!

  Hey Danny,

  It will help you some.

  If (app.documents.length! = 0) {}

  var myFolder = file ("" ~ / Desktop "");

  If (myFolder! = null) {}

  var myPageName, CheminMonFichier, myFile;

  myDocument var = app.activeDocument;

  var my_suffix = parseInt ((app.activeDocument.name) .substr (0.3))

  If (typeof (my_suffix)! = 'number')

  {

  Exit();

  }

  for (var myCounter = 0; myCounter< mydocument.pages.length;="">

  If (. appliedSection.name myDocument.pages.item (myCounter)! = "") {}

  myDocument.pages.item (myCounter).appliedSection.name = "";

  }

  myPageName = myDocument.pages.item (myCounter) .name;

  app.pdfExportPreferences.pageRange = myPageName;

  CheminMonFichier = myFolder + "/" + "MYTEST_" + (my_suffix + myCounter) + ".pdf";

  myFile = new File (myFilePath);

  app.scriptPreferences.userInteractionLevel = UserInteractionLevels.neverInteract;

  myDocument.exportFile (ExportFormat.pdfType, myFile, false, "Type the name of your pre-defined here PDF file");

  app.scriptPreferences.userInteractionLevel = UserInteractionLevels.interactWithAll;

  }

  }

  }

  else {}

  Alert ("no document is open. Please open a document and try again. ») ;

  Exit();

  }

  Alert ("Done");

  Shonky

• I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

  Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

  The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

  Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

• Project seems OK to iMove, using the part of the video is damaged.

  I created a project in iMovie. 10.1.1. everything looks and plays OK.

  It contains only clips and transitions, video camcorder and original sounds.

  It plays OK in iMovie.

  Using the shared file... translates into a corrupted mp4 file.

  I tried various resolutions, always the same result.

  Here is a screenshot of part of the video, which does not play, some static, some jerky movements.

  Thank you.

  

  Hello Tokyo,

  Thanks for the screen shot showing the corruption of the shared iMovie project. It is encouraging that the project plays well in iMovie, but we need to isolate what can happen here.

  Before you begin, it is always good to have up-to-date backups.

  OS X El Capitan: of alternatives for the backup of your Mac

  You have tested with different resolutions.  It also happens with different Compression and quality settings?

  If it works, it can get you an export but we should always isolate why these exports did not work.

  This happens with other projects?  If this isn't the case, then there is a problem with this project specifically.

  If you do not currently have another project to test with you can create a new little project for the test.

  iMovie (2013): create a new movie

  You can use the construction in camera to create new content, fees for the test.

  If the problem is with just the initial project, you can duplicate to troubleshoot a copy.  Duplicate project by clicking on it in the Finder and choose duplicate.

  That your project contains only clips and transitions, first to see if it is a question of transition by removing the (or half of them) and to share to see if it works now.  If it works, one of the deleted transitions is the question and you can begin to add to that their return to isolate.

  If it is not yet implemented with no transition, then it can be a problem of clip. As with transitions, take half and test.

  iMovie (2013): organize your events and projects

  Continue to isolate to refine the offending clip.  Then re - import fresh clip and test.

  Note to check 'the other half' if necessary, it may be easier to delete this test project and to reproduce the original again to continue his tests.

  If the problem occurs with all projects and then see if there is a problem with your user account settings by testing with another user account.

  How to test a question in another account on your Mac - Apple Support

  Test with a new project and see if it works with this new account.  If so, then there is a problem with your user account, and we need to clean up.

  1 open the ~/Library folder in your user account

  2. move anything in the files Caches and preferences that starts with com.apple.imovie on the desktop

  including the iMovie user specific files:

  iMove 2013:

  ~/Library/containers/com. Apple.iMovie.app

  ~/Library/caches/iMovie/

  3. search for and move plugins QuickTime of third party on the desktop:

  / Library/QuickTime /.

  Here's the Apple Codecs that do not need to be removed:

  /Library/QuickTime/AppleIntermediateCodec.component

  /Library/QuickTime/AppleMPEG2Codec.component

  4 restart the computer and test. If it works, you can remove the files from.  If no change, you can put the removed preferences by replacing the newly created files.

  If the problem occurs with the new user iMovie itself may need to be reinstalled.

  OS X Yosemite: install, update and uninstall applications

  This may seem long, but the goal is to isolate which raises the question so we can fix it.

  Please let us know how it goes.