facing problem in communicating with chassis cRIO-9104 NI Max

I tried to communicaste with my cRIO-9004 using the ethernet cable that is connected to the same subnet as the PC master. It is mounted on the cRIO-9104 chassis that has a reconfiurable FPGA and 8 slots.

But I could not find cRIO-9004 in the specified window NOR MAX chassis as unknown.

I am new user of this module and the software. Help, please

Hey, Vinayak,.

I'm not sure that there is a problem here. Usually, you'd do anything with Max modules are you able to add them to your project in LabVIEW?

Tags: NI Hardware

Similar Questions

  • Compliling VI in LabVIEW with cRIO-9004 controller and chassis cRIO-9104

    I tried to compile in LabVIEW with cRIO 9004 and cRIo-9104 connected.

    It has three options

    (1) use the server local compilation.

    (2) to connect to the network compile Server

    (3) to connect to the service of LabVIEW FPGA cloud compile

    But I'm unable to compile my program using one of these.

    How can I get my compilation made? Help, please.

    Thanks YouCp

    Service provider shared's Standard Service program is an annual fee of NOR, which in turn allow you to update your modules and LabVIEW and benefiting from the support of NEITHER.

    https://www.NI.com/services/software_benefits.htm

  • Facing problems of performance with ESXi

    Dear Sir

    I am facing a problem and I couldn't find a solution for her, I have two virtual environment on the site of min and the other on the recovery site, and I use SRM between them.

    The main site contains 12 SUN 6270 blade system 5.1 of VMware ESXi and vcenter 5.1 with clarion Cx4 (SAN storage)

    The DR site contain 5 blade Dell 5.1 of VMware ESXi and vCenter 5.1 with clarion CX4 (SAN storage) system

    I'm Clariion Storage VMAX, my question is on the main site when I add and mount LUN to ESXi hosts when I rescan there took an hour to complete a new analysis, the performance is very bad, in the face of the strange disconnect on the issue of the host, although I checked the compatibility between the Sun and ESXi 5.1 It is compatible

    the DR I'm not confronted with this problem it is fast and the performance is excellent.

    I need a solution please

    Fixed after I removed the clarion and fix some issues on Sun blades fiber cards

    performance of becoming better than before

  • Communication with thermocouple (cRIO)

    Can a Labview software running on a PC to communicate directly with a thermocouple or is needed to communicate with the FPGA or OTR?

    Double wire

  • Problem of indexing with Google Drive sync folder

    Indexing is working in all areas on my Windows 7 computer, except for my folder of Google Sync Drive.  I have already ruled out a problem with google reader.  No there.  Seems to be an indexing problem associated with this folder.  Any suggestions to fix this problem of indexing?

    Hello

    Welcome to the Microsoft Community Forums. I understand that you are facing problem of indexing with Google Sync Drive folder.

    You did changes to the computer before the show?

    I suggest the link and follow the steps in troubleshooting.

    Improve Windows searches using the index: frequently asked questions.

    http://Windows.Microsoft.com/en-in/Windows7/improve-Windows-searches-using-the-index-frequently-asked-questions

    Refer to how to solve problems with search and indexing?

    If the problem persists after you perform the steps in troubleshooting from the link above and if you have problem in Windows, please do not hesitate to answer us, we will be happy to help you.

    Thank you.

  • Photosmart C4795 all-in-1 main: all-in-one HP Photosmart C4700 printer unable to establish 2 way communication with the PC

    I have more than one year of experience using this printer with no problems. Several days ago, it has become unplugged from the PC that I have been using it for over a year & stayed like that for 2 or 3 days. At the end of those 2 or 3 days, the cable has been properly reconnected, but was unable to restore '2 - way communication' with my PC since then.

    As this is a scanner/printer I have proven it always of the functions as a photo Copier.

    To try to solve this problem, I updated the drivers & replaced the cable with a new one without success.

    My OS is Windows 7, as this PC 4 or 5 year, is not compatible with windows 10.

    PS - I would also try to use it with my new PC (a Touchsmart laptop HP with Windows 10 15), but my terms of service for the State of Photosmart C4795 printer software which using the software on more than 1 computer is a violation of the terms of service.

    Running the diagnostics to http://www.hp.com/go/tools can help solve the problem of communication with your PC.  Download and run "print and Scan Doctor."

    For your Windows 10 machine I suggest you download the recommended driver and software from HP here.

  • Problem of Communication of the ISE - AD

    Dear Experts,

    I get the error in ISE while I'm trying to authenticate below.

    "ISE has the problem of communication with active directory with its machine authentication." In the identity of external Sources, the ISE is connected to the group. What to do... ?

    And also please tell me between ISE and AD, using what port number or protocol that he communicates... ?

    Thanks in advance...

    KVS

    Hi Ludovic,.

    That is right. It only supports LDAP on port 389 (clear text), this feature is expected to be supported, but no work has yet been done. This is an improvement for your reference request:

    CSCsx72116 : WLC: Add support for LDAP secure

    Symptom:

    WLC does not support the Protocol LDAPS (secure LDAP).

    Conditions:

    Usually connect to a LDAP secure port 636.

    Workaround solution:

    Plain of using LDAP.

    From now on, either you can continue to use plain LDAP (389) or put the ACS/ISE between to secure communications between them.

    ~ BR
    Jatin kone

    * Does the rate of useful messages *.

  • external communication with swf?

    Hello

    IM loading in intro2swf with the following

    btn_cont2_mc. Visible = false;

    addChildAt (intro_container_mc, 0);
    intro_container_mc.x = 400;
    intro_container_mc.y =-300;

    Stop();

    introvisit();

    function introvisit (): void {}

    If (introlevel == 2) {}
    lvlLoader2 = new Loader();                     Create a new instance of the Loader class
    Url2 = new URLRequest ("intro2.swf");
    lvlLoader2.load (url2); load the SWF file
    intro_container_mc. AddChild (lvlLoader2);

    now the swf file loads correctly and in the right place, but I have a btn on the scene I want to hide, and at a certain point in my loaded swf I want to display the button using a frame event enter


    intro_container_mc.addEventListener (Event.ENTER_FRAME, added0);

    function added0(event:Event):void {}

    If (intro_container_mc.currentFrame == 1) {}

    btn_cont2_mc. Visible = true;

    MovieClip (this.parent).e_mc.cap_talk_txt.text = "Stormy."

    }

    I need to do it this way so that I can change the text at various points in the history of the swf file I can change the text

    but whenever I have it try, the button does not appear or change the text, with problems of communication with swf, I tried

    intro_container_mc.addEventListener (Event.ENTER_FRAME, added0);

    intro_container_mc.lvlLoader2.addEventListener (Event.ENTER_FRAME, added0);

    intro_container_mc.lvlLoader2.storm_mc.addEventListener (Event.ENTER_FRAME, added0);

    who have no effect, the animation inside the swf file is kept in a movie clip called storm_mc

    hope you guys can help me solve this problem

    Thank you

    fonzio

    use:

    function removelistd (): void {}

    {if (Loader.stage)}

    removeChild (loader)

    btn_cont2_mc.buttonMode = false;

    btn_cont2_mc. RemoveEventListener (MouseEvent.CLICK, continuey);

    btn_cont2_mc. RemoveEventListener (MouseEvent.MOUSE_OUT, conty2Out);

    btn_cont2_mc. RemoveEventListener (MouseEvent.MOUSE_OVER, conty2Over);

    swf2Main_mc.storm_mc. RemoveEventListener (Event.ENTER_FRAME, added0);

    loader.contentLoaderInfo.removeEventListener (Event.COMPLETE, completeF);

    }

    }

    ask yourself if it is the charger should I put above

    tried swf2Main_mc and charger in all sorts of ways however continue to be he

    ArgumentError: Error #2025: the supplied DisplayObject must be a child of the caller.

    at flash.display::DisplayObjectContainer/removeChild()

    to MethodInfo - 360)

    to MethodInfo-(357)

    just need help, cleaning and then its done

    Thanks in advance

    fonzio

  • In firefox 30, I am facing problem with my wordpress site. I have a blank page.

    After the update to firefox 30, I am facing problem with my wordpress site. My http://www.anthony.co.in Site works great until firefox 29. but little now a blank page. Tried to reset/reinstall and even tried the other PC. Still the same issue. After downgrade to firefox, my site is back very well. Only problem is with firefox 30. Any help would be useful

    Hello

    Line 500, z-index for less than 81.

    . RM-wrapper > div > {div.rm - front}
    z index: 80;
    }

  • How to read the status of User1 DIP-switch with a cRIO FPGA chassis?

    How to read the State of the DIP switches on a FPGA cRio chassis?

    I work with a cRIO 9022... My idea is to put the system in "service" mode with USER1 switch to IT and communicate with the FPGA via the FPGA - GUI (VI) on the host computer instead via the RT module that is used in normal conditions.

    Any ideas? Unfortunately, I don't have an unused channel on the left... .and (as I know) cannot use the interface RS232 of FPGA.

    Many thanks in advance,

    Luke

    Hi, this is the correct information. You cannot read the FPGA of DIP-switch status. The only thing you could do is to use the function of Reading Switch.vi located under the range of functions-> real-> utilities RT time

    It's how you probably know side host RT and not the FPGA.

    Cordially Virginia

  • Problem with getting communication with old instrument GPIB-ENET/100

    Hello!

    I'm trying to get my program in VB.net to communicate with an older instrument (Infratek 305 A, measure of power) via a GPIB-ENET/100 device.

    The manual of the instrument does not say what GPIB standard, it supports, but the instrument is detected by the measurement and Automation Explorer.

    Detected by that I mean that MAE has detected an instrument located on the right GPIB address, but indicated identification is the output measure instrument string

    instead of the name of instrument (as shown for some more recent instruments of Agilent).

    When I run my application, I followed the communication with NISpy.

    Configuration of the device seems to work and I present only once in the program.

    The problem is reading data from the instrument. Whenever I read the data, I get a correct string of the instrument. But the problem is

    I get the same data in two consecutive and all readings first after that I get new data and also these new data are received in two consecutive readings.

    According to the manual of the instrument the instrument generates the data as follows:

    "A row of data ends with CRLF. The instrument can send multiple rows of data. "When all of the data transfer is complete the EOI (end or identify) is sent.

    My endpoint settings are:

    Send EOI to write complete: YES

    Terminate read on EOS: No.

    EOS byte: 2

    8 bit EOS compare: YES

    Define EOI with EOS on write: No.

    How can I configure the GPIB-ENET/100 to work with my instrument?

    Here are som NISpy logs:

    # Configuration #.

    61 ibwrt(UD3, "C0C2C4C8..", 10 (0xA))
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:43.671 call duration 00:00:00.079
    ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

    62 ThreadIbcntl()

    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:43.750 call duration 00:00:00.000
    ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

    63 ibwrt(UD3, "K0K3K5K9..", 10 (0xA))
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:43.765 call duration 00:00:00.125
    ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

    64 ThreadIbcntl()
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:43.890 call duration 00:00:00.000
    ibsta: 0 x 100 iberr: 0 ibcntl: 10 (0xa)

    65 ibwrt(UD3, "F14F18F24..", 11 (0xB))
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:43.890 call duration 00:00:09.250
    ibsta: 0 x 100 iberr: 0 ibcntl: 11 (0xb)

    66 ThreadIbcntl()
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:54:53.140 call duration 00:00:00.000
    ibsta: 0 x 100 iberr: 0 ibcntl: 11 (0xb)

    ### LU ###

    437 ibrd(UD3, "*AC/1.0A480V/...", 1024 (0x400))
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:58:52.484 call duration 00:00:00.094
    ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

    438 ThreadIbcntl()
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:58:52.578 call duration 00:00:00.000
    ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

    439 ThreadIbcntl()
    PID: 0x0000113C Thread ID: 0x000008B4
    Departure time: 13:58:52.578 call duration 00:00:00.000
    ibsta: 0 x 2100 iberr: 0 ibcntl: 225 (0xe1)

    Hello!

    I don't have the opportunity to test with other controllers.

    However, I found a solution to my problem.

    The instrument should output 4 lines of data.

    L1 - line with comments

    L2 - line with current values

    L3 - line with the values of voltage

    L4 - line with power values

    The first line of the reading stops the instrument of implementation of additional measures.

    The measurements in the instrument began reading the last line of data (L4)

    The problem was that the instrument for a reason any also released a fifth line, which was empty.

    Read this line 5' th stopped the instrument again.

    By configuring the HW to finish reading on EOS, with EOS PMQS, the value byte, I could read the

    buffer of the instrument with a line output instead. This way I could read just L1 - L4

    and the instrument could work again.

    Next time I should read data from the Instr. first of all, I would like to read the empty line, then

    L1 - L4.

    Why the outputs Instr. an additional empty line will be left not resolved.

    My problem is solved.

  • Problem of the printer, I get "the computer is unable to establish two-way communication with the device.

    Original title: printer problem

    "The computer is unable to establish two-way communication with the device. I have pluged a all cables and pluged in that they return.

    Hello
     
    1. What is the brand of your printer?
    2. when the question is is produced?
    3. you remember to make changes to your computer before the problem?
    4. when exactly you get this error?
     
    I would temporarily disable all security software and check if the problem persists.
     

    http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
     
    Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
     
    If you have an HP printer, you can consult the links below.
     
     

    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • Windows has encountered a problem communicating with a device connected to your computer. Status: 0xc00000e9.

    * Original title: 0xc00000e9

    Hi all

    I had a problem - would be great if someone could help me!

    =====

    Windows has encountered a problem communicating with a device connected to your computer.

    This error...

    File: / Boot/bcd

    Status: 0xc00000e9

    Info: An unexpected i/o error has occurred

    ==========

    I press ESC = exit or enter = continue it tries to start, but eventually back to the black screen. So I can't pass this screen. I do not of hava a recovery for Windows disk... And the laptop is a Sony Vaio with Windows 2008. A couple of days, I have connected to my work through the laptop environment and forgot to close - battery went down--and now this...

    Can anyone help?

    Please see the message (response) by Afsal Taher:
    http://answers.Microsoft.com/en-us/Windows/Forum/all/new-computer-running-Windows-7-unexpected-IO-error/46b4fc7a-9a83-4db2-9a00-dca512797e61

  • Windows has encountered a problem communicating with a device connected to your computer.

    When you start the computer laptop, windows Boot Manager appears.

    He reads

    Windows has encountered a problem communicating with a device connected to your computer.

    file: \Boot\BCD

    status: 0xc00000e9

    Info: an unexpected i/o error has occurred.

    When I I go through F8, safe mode, last known good configuration, running in debug ect mode.

    running in safe mode past with him, freezes for abit in the past to a black screen with just the cursor and the Center recovery running VAIO, last good configuration, known debug mode. This windows is loading files, then the windows boot screen were it freezes then goes to a black screen with just a cursor.

    Place the cursor, I am unable to do anything else on this screen.

    is it far from getting the laptop to function normally again or is it finally the end of his life?

    the laptop is a sony VAIO E series (VPCEA25FG) running under windows 7.

    Hello

    The error - an unexpected i/o error has occurred, status: (0Xc00000e9) is a material error in the BIOS of your computer.

    Basically, it's to tell you that the computer is not able to communicate effectively with the hard drive.

    Try the Startup Repair.  Startup Repair is designed to prevent a reinstall tedious to diagnose and repair problems that prevent Windows startup.

    To run the Startup Repair tool, see the links below for more details:

    What are the system recovery options in Windows 7?
    http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7


    Startup Repair: frequently asked questions
    http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

    I also suggest you to update the BIOS. Update the BIOS, contact the manufacturer of the system!

    Warning of the BIOS:

    BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    To ask your question in the Forum of Sony, refer to this link.

    http://community.Sony.com/?XID=M:header:eSupport

  • I bought the Tablet st 2 Dell Latitude with oem windows 8. After a few months. But since August the year last, I am facing problem and my device hung on several occasions.

    Dear Sir, almost a year I bought the Tablet st 2 Dell Latitude with oem windows 8. After a few months, I go to 8.1 and it worked very well. But since August the year last, I am facing problem and my device hung on several occasions. I restored the device, I tried to restored on the plant but no help. Is it possible if I replace win 8 for windows 7 because I feel very uncomfortable.

    Thanks & best regards,

    Hassan jamal Shah

    Please run a check of system files (SFC) & DISM if you're on win 8 or higher 

    All instructions are in our Wiki article below...
    If you have any questions please ask us for .

Maybe you are looking for