Factory accidentally in configuration, how to cope?

Similar Questions

• I have built in speakers of my laptop and I recently accidentally uninstalled them how can I reinstall them?

  I have built in speakers of my laptop and I recently accidentally uninstalled them how can I reinstall them? Please tell me in detail, but if it's simple, so I can do it myself

  Thank you very much

  Hello

  Make a right click the small speaker double click - reading devices - speakers (if not displayed then
  Click in the main box on the Read tab - show disabled right devices)-the general
  tab - use of the device - use this device (enabled)

  View showing the speaker the screen and if necessary to display disabled devices.

  

  -General tab - use of the device - screen display use this device (enabled)

  

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• I have an Officejet Pro L7580 all-in-one. How do you find the printer did how many copies?

  I have an Officejet Pro L7580 all-in-one.  How do I know how many copies the machine made?

  Dragon-fur (unusual name!)

  Thanks again for your suggestions, which led me to the answer.

  Looking more closely at the options in the HP Solution Center, which I thought I had already exhausted, I followed these links - settings, print settings, the Toolbox for printer, information, reviews, myprintmileage, source, which led me to the total number of pages, number of total jobs and many other information, which, apparently, is monitored by HP.

  Thanks for the clues get me there.

  Kind regards

  Tony

• Catch 22 - Port Trunk Configurations: how to combine identifiers VLAN native with DHCP (but allows traffic of VM)

  Catch 22 - Port Network Configurations: how to combine identifiers VLAN native with DHCP (but allow the virtual computer)

  I came across a Catch 22.  Maybe someone can restore the directly here.  I found a "witch hunt" for sure.

  It comes with the Ports of junction on the side of the switch of the ESX host network.

  Context:

  Ok. The Setup is a HP Blade C7000 enclosure.  I try to configure ports for switching to the blades.  ESX 3.5 U4 will be installed the BL460cs.  Installation is preferred method: revive unattended.  No problem with the syntax of Kick-Start,

  I am here, it's the side network.

  The problem:

  I find a major complication in that the switch ports must be configured for both traffic Service Console and VMkernel, more Virtual Machine since only two NICs by blade. Not best practices, but we have only two switches Cisco 3020 inside.  The two uplink physical NIC is paired in the same vSwitch.  (No iSCSI does fortunately).

  So the Catch 22 question is as follows:

  If the id VLAN native set up on the switch port, DHCP works of course and the VMware boot loader is able to grasp a binary / packets on the network (FTP Site) and install OK.  But after no installation, no communication with SC unless I set the VLAN id of the SC to '0 '.  The value "4" 0 does not communication, but "40" is the VLAN native.

  If id configuring VLAN native retired from the Switch port, DHCP will not work and host does not have IP address during the VMware boot process.  This is as expected as traffic without label is not assigned an eligible

  VLAN, so no comms.

  The Port of the Switch configuration:

  interface GigabitEthernet0/16

  SERVERNAME description

  switchport trunk encapsulation dot1q

  switchport trunk vlan native 40

  switchport trunk allowed vlan 40-254

  switchport mode trunk

  switchport nonegotiate

  Speed 1000

  No cdp enable

  spanning tree portfast trunk

  end

  Summary

  OK, let's summarize where things are and if possible please attach responses to their digital identity.

  (1) is there a way to delete the VLAN tagging altogether side ESX host? Not only the id '0 '. The problem is with clearly with the VLAN native defined as "40".  If "40" IDs specified on the Group of ports for the Service Console, no joy, no comms. If the id of '0' value, capable of ping gateway and communicate on the network.

  (2) what is the problem with the definition of VLAN native as "40" when the config for the switch port is set as VLAN native "40"?  Or if it was a problem?  Both parameters clearly do not work together.

  (3) a switch receiving a unmarked frame it will assign to the VLAN Trunk native. Ok. Trunking bases and why I need a VLAN specified on the port for DHCP native work.  But it seems that since the id VLAN is set manually even as VLAN native, closed communications and no traffic as possible.

  (4) executives made tag 802. 1 q VLAN native?  I think that it is not and this could well be the problem. Since the id VLAN "40" is not labeled, but try to score the side host vSwitch port group.

  Please let me know your thoughts, community and how in general, we are approaching 2 NIC ESX configurations.

  When trunking multiple VLANs, you either have a default VLAN is nothing is tagged, or you don't.  That's what the vlan native to you, it defines which VLAN would be used if no tag is visible on the packets traversing the network.  For servers, if you are marking, then everything has to tag, if you're not marking at the server level, then the port must be either an access port or a VLAN native or default must be set.  I also don't keep your service console the same network as your vm.  Keep this isolated for the security of the network.  If you isolate this VLAN, you can separate and use a single IP address for installation and one for post construction.

  Or, you can provide an IP address during the build.

  -KjB

  VMware vExpert

• How/why copies will be created - and they are actual copies?

  Hello

  I search through a collection and I noticed each photo has a copy - the only difference that I see is this 'copy 1' shows under "name of the copy.

  How to get created these copies? Could I have made a copy of each photo in a collection by accidentally hitting a shortcut might be? In addition, these copies of the photo or a few copies in Lightroom?

  When I try to remove them, I have an error message and must use CMD + OPT + SHIFT + DELETE to delete - I delete the original somehow or is the right way to get rid of them?

  See you soon

  Ben

  Looks like virtual copies - Ctrl/Cmd ' (apostrophe), will create and since then Ctrl/Cmd, (comma) is the shortcut for preferences, I have created virtual copies from time to time when my intention was to open the preferences.

  However, it may be useful to develop the error remove them - do not know why there was no error - your problem may run more deep...

  R

• HP Officejet Pro 8610: Unclear Instructions online, using the phone fax configuration, how to print envelopes

  Terminology used in the instructions I'm not familiar with.

  Hi @chazz85,

  I'd be more than happy to help you with your configuration envelopes and printing of fax.

  Are there specific terminology that you want me to explain?

  Let's start with the implementation of the fax machine.

  The best market-well because it is in this document to set up a new Fax.

  For me to simplify this configuration for you, I would need to learn more about the installation of your home Tel/fax line.

  • Is he a dedicated phone line? Only used for faxing.
  • Or is it a shared phone line? Phone and Fax.
  • Is your analog phone provider (typical telephone lines) or digital? (Cable connection)

  If the row is shared;

  • You have the distinctive ring service? 2 numbers, same phone line that present different ringtone profiles to indicate the type of incoming call
  • You have an answering machine? An answering voice calls in the same phone number you use for fax calls.
  • You have voicemail? A subscription to voicemail service using the same phone number as the fax.

  The (Simplified) recommended configuration would be;

  1. Telephone jack in the wall (RJ11) connected to line 1 on the printer using the cable provided in the box with the printer

     Then, if any;

  2. Port 2 - EXT on the back of the printer connected to the answering machine (using a phone cable)
  3. Your phone will then connect on the answering machine (once again using any phone cable)

  Once I have more information about your setup I can help you further.

  Now for printing the envelope.

  I recommend the user to the 8610 Guide to show you how to correctly load an envelope. I copied the steps here for you;

  NOTE: If your printer has a second tray (tray 2), do not insert the envelopes for printing in this slot.

  1. remove the main input tray. Remove all existing paper from the tray.

  

  2. Insert the envelopes facing print down and charge according to the chart. Make sure that the stack of envelopes does not exceed the lower line of the marking in the status bar. For more information, see the diagram engraved in the status bar.

  

  NOTE: Do not load envelopes while the printer prints.

  3. slide the paper width guides in the tray until they touch the edge of the stack of envelopes, then re-insert the tray.

  

  4. remove the output tray extension until the planned paper size is reached.

  

  I need to know what program you are trying to print from. If it's Microsoft Word, I find this document print an envelope very useful.

  If it's another program, you can try the manual suggests.

  1 load the envelopes face to print down in the status bar.

  2. in the menu file in your software, click print.

  3. make sure that your printer is selected.

  4. click on the button that opens the Properties dialog box. Depending on your software application, this button can be called properties, Options, configure the printer, printer, printer or preferences.

  5. Select the appropriate options.

  • Under the layout tab, select Portrait orientation or landscape .
  • On the paper/quality tab, select the paper type appropriate media drop-down list in the area of selection of the status bar, and then select the appropriate, print quality in the quality settings area.
  • Click on the Advanced button in the paper/output box, select the size of paper in the paper size drop-down list.

  6. click OKand then click print or OK in the print dialog box.

  Please let me know if these steps solved your problem, or if there is anything else I can do to help.

  I look forward to hear from you!

  Thank you

• my desktop pc does not recognize my password, can't do reset disk just dvd e-reader, not f g h, can't install flash drive without password. Can I reset to factory settings, if so how.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• camera is accidentally turned on how can I disable it

  Device was accidentally activated by my son. How do you turn it off.

  Found my own answer.  You must open the camera again.  Then pull the top of your toolbar to start, click on 'settings' (you should be in camera app settings now), select "permissions" and there you will see written "webcam and microphone" with a type of cursor "button" and next to him, he said 'on '.  Use your mouse to drag the button completely to the left. Once there, it will show "off".  Problem solved.  Again, it was on a laptop, so not sure how this translates a smartphone.

• My old disk got accidentally formatted. How can I go on the replacement of the 10 component of Photoshop on my new computer? I always have the serial number of the software that I lost.

  How can I download and reinstall Photoshop element 10 on a new computer after my old hard drive got accidentally formatted?

  Download Photoshop Elements products | 11: 10

• Just installed Configurator - how to accept the EULA?

  Hello

  I just downloaded and installed the Configurator on my MacBook Pro with Mac OS X 10.6.3.

  When Configurator starts, it displays a window with the end user license agreement. This window has two buttons "Quit", and click a greyed on 'Accept', which does not have a mouse. I did scroll all the text of the EULA to see if there was any suspicion but could find none.

  How can I activate the button accept?

  If I click the button leaving the Configurator on the EULA window closes (no big surprise).

  Grateful for any advice.

  There is a check box, please select the box first, then the "I agree" button will be activated.

• Feature of Illustrator accidentally turned on - how to disable?

  I must have accidentally pressed something, because Illustrator has just started telling me everything is. Whenever I run my mouse over an object or a path, the outline of the object appears in a light blue color, as well as 'anchor' or 'path', depending on what the object is. See screenshot below.

  

  No one knows what it is and how to disable?

  Some guides.

  Display > bearings commented to turn it off.

• Accidentally blocked Firefox - how to unlock?

  I'm relatively new to using Firefox. When I got a popup asking to connect Firefox, I accidentally blocked Firefox completely. I don't know where to start to recover. I don't want to lose all my favorites. Help!

  Thank you.

  If it was your firewall asking you the weather to allow firefox to connect so you can change that in windows7 by going to start > Control Panel > system and security. Under Firewall, click on allow a program through windows firewall.

  If you cannot run all firefox, go to C:\Program Files\Mozilla Firefox\firefox.exe

  Firefox should run.

  Good luck

• I accidentally loaded MacKeeper, how do I remove it?

  I was downloading what I thought was an upgrade of Flash Player and got MacKeeper on my top bar. Looks a bit like the caricature of WallE Eva. How to get rid of this thing?

  MacKeeper is malware, uninstall it immediately. Always install only site Adobes Flash, NEVER by another site!

  https://MacKeeper.com/uninstall_mackeeper

• Applesyncnotifier.exe accidentally deleted. How can I get that back?

  Original title: Help me please

  I deleted the applesyncnotifier.exe by mistake and I want to install it again. How?

  Hello

  You asked the question correctly

  AppleSyncNotifier.exe sound an application that installs with Itunes that keeps your mp3 files and applications that you put on a mobile device organized and saved

  reinstall iTunes

  Follow the information from apple to the links below

  Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  http://support.Apple.com/kb/HT1923

  ____________________________________________________

  Problem installing iTunes or QuickTime for Windows

  http://support.Apple.com/kb/HT1926

  ____________________________________________________

  and or ask for their support of itunes

  http://www.Apple.com/support/iTunes/

  ____________________________________________________

  Also try the discussions of apple itunes

  http://discussions.Apple.com/category.jspa?categoryID=149

• I restored my pc to factory settings on dvd, how to put my info on my pc?

  I had a lot of problems with my pc, so I restored it back to factory settings. I back up all my files on dvd, but now I'm having problems trying to get the info in my pc.

  They are on C:, but I don't know what to do now... Thanks for your help!

  Hello

  Were these backup files?  Try the following steps:

  http://www.ehow.com/how_7295480_restore-files-DVD.html